This service manual provides instructions for servicing components of JCB backhoe loaders models 3CX, 4CX, and 5CX. It contains sections covering various systems of the machine including the engine, fuel and exhaust systems, cooling system, brake system, hydraulic system, and electrical system. The manual instructs technicians on removing, installing, and servicing components and includes diagrams identifying parts. Safety warnings are provided throughout advising technicians to follow instructions carefully and wear proper protective equipment when servicing machines.
Caterpillar cat 140 h motor grader (prefix cca) service repair manual (cca000...fiskefjskemem
This document provides instructions for assembling a piston pump used in a 140H motor grader. It describes 58 steps to install various components like seals, springs, pins and manifolds. Special tools are required and cleanliness is important to prevent contamination. Finally, it notes the pump must be properly primed and broken in after assembly to avoid early failures.
Jcb 3 cx backhoe loader service repair manual sn from 2254521 and upfujsjefjskekmem
This service manual provides instructions for servicing the components of JCB 3CX, 4CX, and 5CX backhoe loaders. It contains sections on machine systems and components including the engine, fuel and exhaust systems, cooling system, brakes, steering, hydraulics, electrical system and more. Safety information is provided at the beginning noting the importance of understanding the manual before operating the machine.
Jcb 550 140 telescopic handler service repair manual sn from 2902000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear. Safety information is also provided to ensure the work is performed correctly.
Jcb hydradig 110 w wheeled excavator service repair manual (serial no. from 2...fiskefjskemem
This document provides instructions for removing and installing the oil sump on a JCB Hydradig 110W wheeled excavator. It begins with an introduction to the engine's lubrication system and the role of the oil sump. The component identification section outlines the main parts of the oil sump. The removal and installation section provides a step-by-step process for accessing the engine and safely removing the oil sump, replacing gaskets, and reinstalling the sump. Proper torque values for fasteners are also included.
Jcb 536 70 telescopic handler service repair manual sn 2460601 and upfujsjefjwerkskemm
This service manual section contains information about JCB diesel engines. It provides a basic description of engine components and operation, including the starter motor, fuel injection system, lubrication system, and ancillary drive components. The manual identifies internal engine parts such as pistons, connecting rods, valves, bearings, and gears. It specifies that all components should be renewed if worn and that leakages should be prevented during maintenance.
Jcb js160 tier 4i and t4 f excavator service repair manualfujsjefjwerkskemm
This service manual provides instructions for servicing JCB excavators models JS115 through JS190. It contains sections on the machine body and framework, operator station, engine, driveline, hydraulic system, electrical system and other components. The section on the engine covers topics like removing and installing the rocker cover, camshaft, tappets and oil sump. Precise instructions are provided along with torque specifications and safety warnings.
Caterpillar cat 305.5 e mini hydraulic excavator (prefix mx5) service repair ...fiskefjskemem
The document provides instructions for servicing components of a 305.5E Mini Hydraulic Excavator powered by a C2.4 engine. It includes procedures for removing and installing the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The steps describe using various tools and ensuring proper alignment of components and timing marks during installation.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 140 h motor grader (prefix cca) service repair manual (cca000...fiskefjskemem
This document provides instructions for assembling a piston pump used in a 140H motor grader. It describes 58 steps to install various components like seals, springs, pins and manifolds. Special tools are required and cleanliness is important to prevent contamination. Finally, it notes the pump must be properly primed and broken in after assembly to avoid early failures.
Jcb 3 cx backhoe loader service repair manual sn from 2254521 and upfujsjefjskekmem
This service manual provides instructions for servicing the components of JCB 3CX, 4CX, and 5CX backhoe loaders. It contains sections on machine systems and components including the engine, fuel and exhaust systems, cooling system, brakes, steering, hydraulics, electrical system and more. Safety information is provided at the beginning noting the importance of understanding the manual before operating the machine.
Jcb 550 140 telescopic handler service repair manual sn from 2902000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear. Safety information is also provided to ensure the work is performed correctly.
Jcb hydradig 110 w wheeled excavator service repair manual (serial no. from 2...fiskefjskemem
This document provides instructions for removing and installing the oil sump on a JCB Hydradig 110W wheeled excavator. It begins with an introduction to the engine's lubrication system and the role of the oil sump. The component identification section outlines the main parts of the oil sump. The removal and installation section provides a step-by-step process for accessing the engine and safely removing the oil sump, replacing gaskets, and reinstalling the sump. Proper torque values for fasteners are also included.
Jcb 536 70 telescopic handler service repair manual sn 2460601 and upfujsjefjwerkskemm
This service manual section contains information about JCB diesel engines. It provides a basic description of engine components and operation, including the starter motor, fuel injection system, lubrication system, and ancillary drive components. The manual identifies internal engine parts such as pistons, connecting rods, valves, bearings, and gears. It specifies that all components should be renewed if worn and that leakages should be prevented during maintenance.
Jcb js160 tier 4i and t4 f excavator service repair manualfujsjefjwerkskemm
This service manual provides instructions for servicing JCB excavators models JS115 through JS190. It contains sections on the machine body and framework, operator station, engine, driveline, hydraulic system, electrical system and other components. The section on the engine covers topics like removing and installing the rocker cover, camshaft, tappets and oil sump. Precise instructions are provided along with torque specifications and safety warnings.
Caterpillar cat 305.5 e mini hydraulic excavator (prefix mx5) service repair ...fiskefjskemem
The document provides instructions for servicing components of a 305.5E Mini Hydraulic Excavator powered by a C2.4 engine. It includes procedures for removing and installing the crankshaft rear seal, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The steps describe using various tools and ensuring proper alignment of components and timing marks during installation.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Jcb 509 42 telescopic handler service repair manual sn from 1402020 and upfdjjsekksemxs
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks with model numbers 506-36, 507-42, 509-42, 510-56, and 512-56. The manual contains sections covering the machine components, including the engine, brake system, hydraulic system, electrical system, and driveline. The section summarized provides instructions for removing and installing the front and rear cases of the semi-automatic gearbox. The process requires using various special tools and consumables, checking clutch shaft end floats, and applying sealants and threadlocker to fasteners.
This service manual provides instructions for servicing components of the 6TFT and 6TST engines, including the engine, body and framework, operator station, fuel and exhaust systems, cooling system, brakes, steering, driveline, hydraulic system, electrical system, fasteners, and consumable products. The manual contains sections on general information, component identification, and procedures for removing and installing parts. Safety precautions are provided throughout regarding safe operation and maintenance of the machine.
Jcb js220 tracked excavator service repair manual sn from 2460501 onwardsfusjefjkskem
This service manual provides information on servicing excavator models JS200, JS210, JS220, and JS235. It contains instructions from the manufacturer and copyrighted content. The manual covers safety procedures and contains sections on various machine systems including the engine, fuel system, cooling system, driveline, hydraulics, electrical system and other components.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fusjefjkskem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
Jcb tm420 telescopic wheel loader service repair manual sn 2454001 and upfusjjfksekmme
This service manual section provides instructions for removing and installing the master clutch, as well as disassembling and assembling it. The master clutch controls gear changes in the transmission. Removal involves using jacking bolts and threaded lifting eyes to detach the clutch cover and drum. Assembly is the reverse of disassembly, replacing worn parts as needed and applying the specified torques. Special tools like retainers and a mandrel are required for some steps.
Jcb 325 t skid steer loader service repair manual sn from 2476302 to 2477300fujsjefjskekmem
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb 135 hd skid steer loader service repair manual (sn 2431601 and up)fiskefjskemem
This service manual provides instructions for servicing a JCB 135 HD and 155 HD skid steer loader. It contains sections covering the machine systems, including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides detailed descriptions of components, operating principles, maintenance and repair procedures, specifications, and safety information. Technicians are instructed to carefully follow the procedures in the manual to properly service the machine.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upfiskefjskemem
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics, and electrical systems. Specific models covered include 526-56, 531-70, 533-105, 535-95, 536-60, and others. Safety warnings are provided throughout and procedures for removal and installation are described in detail with torque specifications.
Jcb 65 r 1 compact excavator service repair manual (sn from 1913904 to 1914244)fusefjjskekemm
This service manual provides instructions for servicing the excavator track and running gear components. It includes sections on track adjustment and removal/installation of various track components like steel and rubber tracks, track links, idler wheels, and the gearbox sprocket. Safety warnings are provided throughout advising technicians to properly support the machine, release tension slowly, and take precautions when working with recoil units.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
Claas axion 850 810 (type a09) tractor service repair manualfusefjskekkmem
1) The document provides instructions for removing and refitting the front axle, epicycloid reducer, and joint unit on a CLAAS AXION 850-810 tractor.
2) Key steps when removing the front axle include draining fluids, removing mounting hardware, wheels, and radiator components.
3) Dismantling the epicycloid reducer involves removing gears, bearings, seals, and mounting components.
4) Removing the joint unit requires taking off the steering bars, supports, and wheel shaft.
Jcb 540 v180 telescopic handler service repair manual sn from 2902000 onwardscdfvvv
This service manual provides instructions for servicing the Loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upcdfvvv
This service manual provides information for servicing and repairing Loadall rough terrain variable reach trucks. It contains instructions for machine components, attachments, body and framework, operator station, heating and air conditioning, engine, fuel and exhaust systems, cooling system, brake system, steering system, driveline, hydraulic system, and electrical system. The manual instructs technicians on removal and installation of components like the engine, and provides torque specifications and other technical details.
Jcb 536 70 lp tier 4 telescopic handler service repair manual sn from 2460601...cdfvvv
This document provides service and repair instructions for fuel injectors in JCB Loadall vehicles. It begins with an introduction to the injector components and operation. The main sections provide procedures for checking injector operation with diagnostic tools, removing and installing individual injectors, and removing and installing injector seals in the cylinder head. The summary highlights that the document contains procedures for servicing fuel injectors, including checking operation, removing and installing individual injectors, and removing and installing injector seals.
Jcb 536 70 tier 4 telescopic handler service repair manual sn from 2902000 on...cdfvvv
This document provides service and repair instructions for fuel injectors on JCB Loadall vehicles. It describes injector components and identification, includes a check procedure using diagnostic tools, and outlines removal and installation steps. Special tools are required for tasks like leak testing and installing injector seals. Torque specifications are provided for reinstalling injectors and seals.
Jcb 536 60 telescopic handler service repair manual sn 2460601 and upcdfvvv
This document provides instructions for removing and installing the bedplate on a 4-cylinder JCB engine. Key steps include:
1. Removing components like the engine, drive belt, oil sump, fuel pipes and injectors, rocker cover and assembly.
2. Positioning the engine upside down supported at the front cylinder block.
3. Removing the flywheel.
4. Using a template and sealant to install the new bedplate, and torquing bolts to the specified values.
Jcb 535 95 telescopic handler service repair manual sn 2460601 and upcdfvvv
This service manual section provides information on servicing the engine. It describes the basic operation and components of the JCB Tier 2/3 4-cylinder diesel engine. The introduction covers the engine systems and operation, including fuel injection, air intake, lubrication, and ancillary drive. Component identification diagrams show the major internal engine parts.
Jcb 531 70 telescopic handler service repair manual sn 2460601 and upcdfvvv
This service manual section provides information on servicing the engine. It describes the basic operation and components of the JCB Tier 2/3 4-cylinder diesel engine. The introduction covers the engine systems and operation, including fuel injection, air intake, lubrication, and ancillary drive. Component identification diagrams show the major internal engine parts.
Jcb 526 56 telescopic handler service repair manual sn 2460601 and upcdfvvv
This service manual section provides information on servicing the engine. It describes the basic operation and components of the JCB Tier 2/3 4-cylinder diesel engine. The introduction outlines the engine systems and operation, including fuel injection, valve actuation, lubrication, cooling and starting. Component identification diagrams show the major internal and external engine parts.
Jcb 225 t skid steer loader service repair manual sn from 2478301 to 2478700cdfvvv
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine overview, attachments, body/framework, operator station, HVAC, engine, fuel/exhaust, cooling, brakes, driveline, hydraulics, and electrical systems. The section summarized focuses on servicing the engine crankshaft, including removal/installation instructions and specifications. Technicians are advised to follow all safety procedures, use the proper tools, and replace all worn parts.
Jcb 225 t skid steer loader service repair manual sn from 2476302 to 2477300cdfvvv
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine overview, attachments, body/framework, operator station, HVAC, engine, fuel/exhaust, cooling, brakes, driveline, hydraulics, and electrical systems. The document provides an introduction to servicing the engine crankshaft, including guidelines on checking crankshaft condition and removing/installing the crankshaft. Technicians are instructed to follow all safety procedures, use the proper tools, and replace all necessary components.
Jcb 509 42 telescopic handler service repair manual sn from 1402020 and upfdjjsekksemxs
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks with model numbers 506-36, 507-42, 509-42, 510-56, and 512-56. The manual contains sections covering the machine components, including the engine, brake system, hydraulic system, electrical system, and driveline. The section summarized provides instructions for removing and installing the front and rear cases of the semi-automatic gearbox. The process requires using various special tools and consumables, checking clutch shaft end floats, and applying sealants and threadlocker to fasteners.
This service manual provides instructions for servicing components of the 6TFT and 6TST engines, including the engine, body and framework, operator station, fuel and exhaust systems, cooling system, brakes, steering, driveline, hydraulic system, electrical system, fasteners, and consumable products. The manual contains sections on general information, component identification, and procedures for removing and installing parts. Safety precautions are provided throughout regarding safe operation and maintenance of the machine.
Jcb js220 tracked excavator service repair manual sn from 2460501 onwardsfusjefjkskem
This service manual provides information on servicing excavator models JS200, JS210, JS220, and JS235. It contains instructions from the manufacturer and copyrighted content. The manual covers safety procedures and contains sections on various machine systems including the engine, fuel system, cooling system, driveline, hydraulics, electrical system and other components.
Caterpillar cat 938 g wheel loader (prefix 9hs) service repair manual (9hs000...fusjefjkskem
The document provides instructions for removing and installing the cylinder head on a Caterpillar 3126 engine. It describes removing components like the fuel filter base, governor, and manifolds before removing the cylinder head bolts and gasket. For installation, it instructs to clean surfaces, install a new gasket, lubricate and tighten bolts in a specific sequence, and then reinstall the removed components. It also provides guidance on checking reusable parts and contains safety notices.
Jcb tm420 telescopic wheel loader service repair manual sn 2454001 and upfusjjfksekmme
This service manual section provides instructions for removing and installing the master clutch, as well as disassembling and assembling it. The master clutch controls gear changes in the transmission. Removal involves using jacking bolts and threaded lifting eyes to detach the clutch cover and drum. Assembly is the reverse of disassembly, replacing worn parts as needed and applying the specified torques. Special tools like retainers and a mandrel are required for some steps.
Jcb 325 t skid steer loader service repair manual sn from 2476302 to 2477300fujsjefjskekmem
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb 135 hd skid steer loader service repair manual (sn 2431601 and up)fiskefjskemem
This service manual provides instructions for servicing a JCB 135 HD and 155 HD skid steer loader. It contains sections covering the machine systems, including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides detailed descriptions of components, operating principles, maintenance and repair procedures, specifications, and safety information. Technicians are instructed to carefully follow the procedures in the manual to properly service the machine.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upfiskefjskemem
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics, and electrical systems. Specific models covered include 526-56, 531-70, 533-105, 535-95, 536-60, and others. Safety warnings are provided throughout and procedures for removal and installation are described in detail with torque specifications.
Jcb 65 r 1 compact excavator service repair manual (sn from 1913904 to 1914244)fusefjjskekemm
This service manual provides instructions for servicing the excavator track and running gear components. It includes sections on track adjustment and removal/installation of various track components like steel and rubber tracks, track links, idler wheels, and the gearbox sprocket. Safety warnings are provided throughout advising technicians to properly support the machine, release tension slowly, and take precautions when working with recoil units.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
Claas axion 850 810 (type a09) tractor service repair manualfusefjskekkmem
1) The document provides instructions for removing and refitting the front axle, epicycloid reducer, and joint unit on a CLAAS AXION 850-810 tractor.
2) Key steps when removing the front axle include draining fluids, removing mounting hardware, wheels, and radiator components.
3) Dismantling the epicycloid reducer involves removing gears, bearings, seals, and mounting components.
4) Removing the joint unit requires taking off the steering bars, supports, and wheel shaft.
Jcb 540 v180 telescopic handler service repair manual sn from 2902000 onwardscdfvvv
This service manual provides instructions for servicing the Loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upcdfvvv
This service manual provides information for servicing and repairing Loadall rough terrain variable reach trucks. It contains instructions for machine components, attachments, body and framework, operator station, heating and air conditioning, engine, fuel and exhaust systems, cooling system, brake system, steering system, driveline, hydraulic system, and electrical system. The manual instructs technicians on removal and installation of components like the engine, and provides torque specifications and other technical details.
Jcb 536 70 lp tier 4 telescopic handler service repair manual sn from 2460601...cdfvvv
This document provides service and repair instructions for fuel injectors in JCB Loadall vehicles. It begins with an introduction to the injector components and operation. The main sections provide procedures for checking injector operation with diagnostic tools, removing and installing individual injectors, and removing and installing injector seals in the cylinder head. The summary highlights that the document contains procedures for servicing fuel injectors, including checking operation, removing and installing individual injectors, and removing and installing injector seals.
Jcb 536 70 tier 4 telescopic handler service repair manual sn from 2902000 on...cdfvvv
This document provides service and repair instructions for fuel injectors on JCB Loadall vehicles. It describes injector components and identification, includes a check procedure using diagnostic tools, and outlines removal and installation steps. Special tools are required for tasks like leak testing and installing injector seals. Torque specifications are provided for reinstalling injectors and seals.
Jcb 536 60 telescopic handler service repair manual sn 2460601 and upcdfvvv
This document provides instructions for removing and installing the bedplate on a 4-cylinder JCB engine. Key steps include:
1. Removing components like the engine, drive belt, oil sump, fuel pipes and injectors, rocker cover and assembly.
2. Positioning the engine upside down supported at the front cylinder block.
3. Removing the flywheel.
4. Using a template and sealant to install the new bedplate, and torquing bolts to the specified values.
Jcb 535 95 telescopic handler service repair manual sn 2460601 and upcdfvvv
This service manual section provides information on servicing the engine. It describes the basic operation and components of the JCB Tier 2/3 4-cylinder diesel engine. The introduction covers the engine systems and operation, including fuel injection, air intake, lubrication, and ancillary drive. Component identification diagrams show the major internal engine parts.
Jcb 531 70 telescopic handler service repair manual sn 2460601 and upcdfvvv
This service manual section provides information on servicing the engine. It describes the basic operation and components of the JCB Tier 2/3 4-cylinder diesel engine. The introduction covers the engine systems and operation, including fuel injection, air intake, lubrication, and ancillary drive. Component identification diagrams show the major internal engine parts.
Jcb 526 56 telescopic handler service repair manual sn 2460601 and upcdfvvv
This service manual section provides information on servicing the engine. It describes the basic operation and components of the JCB Tier 2/3 4-cylinder diesel engine. The introduction outlines the engine systems and operation, including fuel injection, valve actuation, lubrication, cooling and starting. Component identification diagrams show the major internal and external engine parts.
Jcb 225 t skid steer loader service repair manual sn from 2478301 to 2478700cdfvvv
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine overview, attachments, body/framework, operator station, HVAC, engine, fuel/exhaust, cooling, brakes, driveline, hydraulics, and electrical systems. The section summarized focuses on servicing the engine crankshaft, including removal/installation instructions and specifications. Technicians are advised to follow all safety procedures, use the proper tools, and replace all worn parts.
Jcb 225 t skid steer loader service repair manual sn from 2476302 to 2477300cdfvvv
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine overview, attachments, body/framework, operator station, HVAC, engine, fuel/exhaust, cooling, brakes, driveline, hydraulics, and electrical systems. The document provides an introduction to servicing the engine crankshaft, including guidelines on checking crankshaft condition and removing/installing the crankshaft. Technicians are instructed to follow all safety procedures, use the proper tools, and replace all necessary components.
Jcb 155 hd skid steer loader service repair manual (sn 2431601 and up)cdfvvv
This service manual provides information for servicing a JCB 135 HD and 155 HD skid steer loader. It contains sections covering the machine systems, including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides illustrations and instructions for removal, installation, maintenance, and repair of parts. Safety precautions are described, requiring technicians to fully understand the manual before operating or servicing the machine.
Jcb 135 hd skid steer loader service repair manual (sn 2431601 and up)cdfvvv
This service manual provides instructions for servicing a JCB skid steer loader models 135 HD and 155 HD. It contains sections covering the machine systems including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides detailed descriptions of components, operating principles, maintenance and repair procedures, specifications, and safety information. Technicians are instructed to carefully follow the procedures in the manual to properly service the loader and ensure safe operation.
Jcb 5 cx backhoe loader service repair manual sn from 2509500 and upcdfvvv
This service manual provides instructions for servicing components of JCB backhoe loaders models 3CX, 4CX, and 5CX. It contains sections covering various systems of the machine including the engine, fuel and exhaust systems, cooling system, brake system, hydraulic system, and electrical system. The manual instructs technicians on removing, installing, and servicing components and includes diagrams identifying parts. Safety warnings are provided throughout advising technicians to follow instructions carefully and wear proper protective equipment when servicing machines.
Jcb 3 cx backhoe loader service repair manual sn from 2509500 and upcdfvvv
This service manual provides instructions for servicing components of JCB 3CX, 4CX, and 5CX backhoe loaders, including the machine, attachments, body, operator station, HVAC, engine, fuel and exhaust systems, cooling system, brake system, steering system, driveline, hydraulic system, electrical system, fasteners, consumable products, and after sales. The manual contains safety warnings and instructions for removing and installing components. It provides identification diagrams and specifications for proper servicing.
Caterpillar cat 305.5 e mini hydraulic excavator (prefix mx5) service repair ...cdfvvv
The document provides instructions for servicing components of a 305.5E Mini Hydraulic Excavator engine. It describes procedures for removing and installing the crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The summaries provide tools needed and step-by-step instructions for each procedure.
Caterpillar cat 303 e cr mini hydraulic excavator (prefix smg) service repair...cdfvvv
The document provides instructions for removing and installing a governor and fuel injection pump on a Caterpillar 303E CR Mini Hydraulic Excavator. It describes removing 11 parts in 11 steps to remove the governor, including bolts, springs, plates and shafts. It then describes installing the governor in 11 corresponding steps. Separate sections provide 3 steps to remove the fuel injection pump and 4 steps to install it, noting the importance of matching shim thicknesses. Another section outlines 4 steps for removing fuel injectors and 4 steps for installing them.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rse) service repair ...cdfvvv
The document provides instructions for disassembling and assembling the swing motor and swing drive of a 303.5E Mini Hydraulic Excavator. It lists 32 steps for disassembly, removing components like valves, springs, spools, checks valves, plates, and gears. It then lists 28 steps for assembly, installing these components in reverse order. Precautions are provided for parts under spring force. Required tools include bearing pullers, crossblocks, and retaining ring pliers.
Caterpillar cat 140 h motor grader (prefix cca) service repair manual (cca000...cdfvvv
1) The document provides assembly instructions for a piston pump used in a 140H motor grader.
2) It describes 57 assembly steps involving over 30 individual parts like pistons, springs, seals, and manifolds.
3) Special tools and cleanliness are emphasized to prevent damage during assembly, and proper break-in is noted after assembly is complete.
Caterpillar cat 140 h motor grader (prefix 8km) service repair manual (8km000...cdfvvv
This document provides instructions for removing and installing various engine components on a Caterpillar 140H motor grader, including:
- Inlet and exhaust valves
- Valve guides
- Valve seat inserts
- Engine oil filter base
The instructions include lists of required tools, step-by-step procedures, diagrams, and safety notices for each component.
Caterpillar cat 140 g motor grader (prefix 13w) service repair manual (13w004...cdfvvv
This document provides instructions for servicing the hydraulic pump and control valves on a Caterpillar 140G motor grader. It describes how to remove and install the hydraulic pump, including disconnecting hoses and removing mounting hardware. It also details how to disassemble and assemble the pump for component replacement. Separate instructions are provided for removing and installing the hydraulic control valves as an assembly, and then further disassembling the valves.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. 15 - Engine
54 - Flywheel
00 - General
15 - 217 9813/6950-3 15 - 217
00 - General
Introduction .................................................. 15-217
Component Identification ............................. 15-218
Remove and Install ..................................... 15-219
Introduction
Flywheels are used to provide continuous energy in
systems, where the energy source is not continuous.
In such cases, the flywheel stores energy when
torque is applied by the energy source, and it
releases stored energy when the energy source is
not applying torque to it.
In a reciprocating engine, a flywheel is used to
maintain constant angular velocity of the crankshaft.
The flywheel, which is mounted on the crankshaft,
stores energy when torque is exerted on it by a firing
piston, and it releases energy to its mechanical loads
when no piston is exerting torque on it.
4. 15 - Engine
54 - Flywheel
00 - General
15 - 219 9813/6950-3 15 - 219
Remove and Install
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start. The flywheel is installed with a
crankshaft position sensor target disc. DO NOT
remove the target disc. If the disc is defective the
flywheel must be replaced.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
Removal
1. Remove the bolts and withdraw the flywheel from
the crankshaft hub. The bolts MUST NOT be
reused. Discard the bolts.
Figure 330.
1
2
1
3
T3
1 Flywheel 2 Flywheel fixing bolts (x8)
3 Flywheel location dowel Y Angle tightening mark
5. 15 - Engine
54 - Flywheel
00 - General
15 - 220 9813/6950-3 15 - 220
Installation
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. Align the flywheel location dowel.
4. Renew the fixing bolts. Tighten the new bolts to
the correct torque value in three stages.
Tighten the bolts in sequence in diagonally opposing
pairs. As a visual check, mark the bolts to the
flywheel before you start. When the bolts have been
angle tightened the marks will appear as at 120°.
Table 111. Torque Table
Item Torque Value
(Nm)
Angle (de-
grees)
2 (Ist Stage) 40
2 (2nd Stage) 120
2 (Final Stage) +120
6. 15 - Engine
54 - Flywheel
03 - Housing
15 - 221 9813/6950-3 15 - 221
03 - Housing
Remove and Install
Special Tools
Description Part No. Qty.
Template for Sealant
Flywheel Housing to
Gear Case (4 Cyl Elec )
892/12349 1
Before Removal
The flywheel housing is integral with the drive gears
front case. When the housing is removed the drive
gears will be exposed. DO NOT attempt to remove
the camshaft and the drive gears. Removing the
camshaft with the engine in the upright position will
cause the tappets to dislodge, requiring the engine
block to be dismantled.
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start.
2. Remove the flywheel. Refer to (PIL 15-54).
3. Remove the starter motor. Refer to (PIL 15-75).
Removal
1. Remove the flywheel housing fixing bolts and
then separate the flywheel housing from the gear
case.
2. If required, undo the bolts and remove the access
cover.
3. Remove and discard the crankshaft rear oil seal.
Take care not to damage the seal bore in the
housing.
7. 15 - Engine
54 - Flywheel
03 - Housing
15 - 222 9813/6950-3 15 - 222
Figure 331.
4
2
5
1
7
6
3
X
2 Y
T4
Y
Y
Z
1 Flywheel housing 2 Dowel - 12 mm
3 Dowel - 10 mm 4 Flywheel housing fixing bolts (x6) M10
5 Flywheel housing fixing bolts (x12) M8 6 Access cover
7 Access cover fixing bolts (x2) Y Fixing point
X Flywheel housing mating face Z Alternative fixing holes
T3 Alignment pins T4 Sealant template
Before Installation
1. Carefully remove all traces of the old sealant
compound from the flywheel housing mating
faces.
2. Use a suitable degreasing agent to clean the
inside of the flywheel housing.
3. Carefully inspect all gears, bearings and shafts
for signs of excessive wear or damage. If wear
or damage is evident, the components must be
renewed.
8. 15 - Engine
54 - Flywheel
03 - Housing
15 - 223 9813/6950-3 15 - 223
Installation
Anaerobic sealant will not start to cure whilst it
is open to the atmosphere, however when air is
excluded (for instance when the two parts are
put together) it will immediately start to harden.
Make sure that all the necessary tools, bolts
etc. are readily available prior to assembling the
components. The parts must be installed and torque
tightened within5min with a maximum permissible
time of 15min
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. Make sure that the dowels are installed to the
mating face of the flywheel housing.
4. Install the sealant template T4 on the housing.
Locate the holes in the template, use the dowel
and three fixing bolts in the fixing points.
Special Tool: Template for Sealant Flywheel
Housing to Gear Case (4 Cyl Elec ) (Qty.: 1)
5. Use the template T4 as a guide, apply a
continuous bead of sealant around the flywheel
housing mating face
Length/Dimension/Distance: 1.5mm
5.1. Some engines feature a flywheel housing
with a different fixing hole pattern. Use the
template to apply the sealant but apply
sealant manually in the position shown at Z.
6. Remove the three fixing bolts at positions.
Remove the template T4, make sure not to
smudge the sealant. Discard the template.
7. Locate the flywheel housing on the alignment
pins T3 on the crankcase and install the fixing
bolts. Progressively tighten the bolts to the
correct torque value.
7.1. Remove the alignment pins to install the last
two M10 fixing bolts.
7.2. The parts must be separated, thoroughly
cleaned and fresh sealant applied if the
parts have not been torque tightened within
the maximum time period.
Duration: 15min
8. Install the access cover and use the bolts to
secure. Tighten the bolts to the correct torque
value. Refer to Table 112.
After Installation
1. Install a new crankshaft rear oil seal.
2. Install the flywheel.
3. Install the starter motor.
Table 112. Torque Values
Item Nm
4 47
5 24
7 24
9. 15 - Engine
54 - Flywheel
09 - Gear Ring
15 - 224 9813/6950-3 15 - 224
09 - Gear Ring
Remove and Install
CAUTION Wear eye protection when you drive
the gear ring off the flywheel.
If the flywheel gear teeth are damaged or excessively
worn, the gear ring can be replaced with a new one.
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start.
2. Remove the flywheel from the crankshaft hub.
Figure 332.
1
2
X
1 Flywheel
2 Gear ring
x Position of hole
Removal
1. Note that the gear teeth have a lead-in chamfer
on one side to assist the starter motor pinion to
engage. Note which way around the gear ring is
installed to make sure that the new gear ring is
installed the same way on assembly.
2. Place the flywheel flat on a firm surface. Drill a
hole through the gear ring below the root of one
of the gear teeth as shown. Drive a chisel into the
adjacent tooth to spread the gear ring apart. Take
care not to damage the flywheel or the position
sensor target disc.
Installation
1. Make sure that all items are clean and free from
damage and corrosion.
2. Heat up the new gear ring, preferably in an oven
to make sure that the heat is applied evenly
around the circumference. Do not heat the gear
ring above
Temperature: 200°C (391.7°F)
3. When sufficiently heated, install the gear ring into
position over the flywheel. Make sure that the
gear ring is installed the correct way around.
After Installation
1. Install the flywheel to the crankshaft hub.
10. 15 - Engine
60 - Oil Pump
00 - General
15 - 227 9813/6950-3 15 - 227
00 - General
Introduction .................................................. 15-227
Component Identification ............................. 15-228
Check (Condition) ........................................ 15-230
Remove and Install ..................................... 15-231
Introduction
The oil pump is a rotor type pump located inside the
timing gear case. The pump is driven by gears via
the crankshaft.
The pump consists of two rotors, one running inside
the other. The outer rotor has one more lobe than the
inner rotor and turns on a different axis.
When rotated the gap between the inner and outer
rotor lobes increases, drawing oil in through the
inlet port. After a half rotation the gap reaches a
maximum, the inlet port is closed and the outlet port
opens.
Further rotation causes the gap between the lobes to
diminish, forcing the oil out through the outlet port.
A pressure relief valve assembly is integral with the
pump body. As oil pressure increases it acts on a
spool to overcome the pressure of the spring. As the
spool moves it uncovers a port allowing pressurised
oil directly back to the inlet port. In practice the
spool is continually opening and closing to maintain
the correct oil pressure value. The valve is not
adjustable.
11. 15 - Engine
60 - Oil Pump
00 - General
15 - 228 9813/6950-3 15 - 228
Component Identification
Figure 333.
1
1 3 2 4
4
9
6
1
7 7a
8 8a
5
5
1 Oil pump 2 Outer rotor
3 Inner rotor 4 Inlet port
5 Outlet port 6 Relief valve assembly
7 Relief valve spring 7a Relief valve port (return to inlet port 4)
8 Relief valve spool 8a Relief valve pressure port (connected to port 5)
9 Oil pump connecting ports (engine bed plate)
12. 15 - Engine
60 - Oil Pump
00 - General
15 - 229 9813/6950-3 15 - 229
Figure 334.
10
10 CCV Anti drain back valve
13. 15 - Engine
60 - Oil Pump
00 - General
15 - 230 9813/6950-3 15 - 230
Check (Condition)
1. Check the oil pump internal parts for signs of
damage and excessive wear.
2. Use feeler gauges to measure the inner and
outer rotor clearance, and the rotor end float to
confirm they are within service limits.
Refer to: PIL 15-12-00.
14. 15 - Engine
60 - Oil Pump
00 - General
15 - 231 9813/6950-3 15 - 231
Remove and Install
Special Tools
Description Part No. Qty.
Torque Wrench
(10-100Nm)
993/70111 1
The illustrations show the engine inverted. If the
oil pump is being removed prior to crankshaft or
camshaft removal, the engine must be inverted. If
the oil pump only is being removed (for inspection or
renewal) then the engine need not be inverted.
This procedure requires service parts. Make sure
you have obtained the correct service parts before
you start, refer to Parts Catalogue.
Before Removal
1. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
2. Drain the oil from the engine, refer to (PIL 15-21).
3. Remove the starter motor, refer to (PIL 15-75).
4. Remove the flywheel, refer to (PIL 15-54).
5. Remove the flywheel housing, refer to (PIL
15-54).
Figure 335.
X
Y
2
1
3
4
1 Oil pump 2 Oil pump fixing bolts (x4)
3 Flywheel hub 4 Flywheel hub fixing bolt
X Crankshaft gear Y Oil pump location dowel
15. 15 - Engine
60 - Oil Pump
00 - General
15 - 232 9813/6950-3 15 - 232
Remove
1. Remove the flywheel hub fixing bolt.
2. Remove the flywheel hub. DO NOT remove the
crankshaft gear.
3. Remove the oil pump fixing bolts and lift the oil
pump away from the timing gear case.
The oil pump is a non-serviceable item. If the oil
pump is damaged or worn it must be renewed as a
complete assembly.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all parts are clean and free from
damage and corrosion.
3. Lubricate the pump rotor with clean engine oil.
4. Make sure that the oil pump location dowel
locates into the hole in the gear timing case.
5. Install the flywheel hub into the crankshaft gear,
locating on the dowel. Tighten the bolts to the
correct torque value.
Special Tool: Torque Wrench (10-100Nm) (Qty.:
1)
After Replacement
1. Install the flywheel housing, refer to (PIL 15-54).
2. Install the flywheel to the crankshaft hub, refer to
(PIL 15-54).
3. Install the starter motor, refer to (PIL 15-75).
4. Fill the engine with engine oil, refer to (PIL
15-21).
Table 113. Torque Values
Item Nm
2 24
4 47
16. 15 - Engine
84 - Sensor
09 - Knock
15 - 289 9813/6950-3 15 - 289
Remove and Install
The following procedure is for one knock sensor. The
procedure for both sensors is identical.
Before Removal
1. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
Remove
1. Get access to the engine.
2. Disconnect the electrical connector at the knock
sensor.
3. Remove the bolt and remove the knock sensor
from the crankcase.
The knock sensor is a non-serviceable item. If the
sensor is defective it must be replaced.
Figure 366.
A
B C
A Knock sensor
B Electrical connector
C Bolt
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that the sensor mates fully with the
adjacent face on the crankcase.
3. Tighten the bolt to the correct torque value.
Torque: 22–26N·m
17. 15 - Engine
84 - Sensor
14 - Exhaust Manifold Temperature
15 - 290 9813/6950-3 15 - 290
14 - Exhaust Manifold Temperature
Introduction .................................................. 15-290
Operation ..................................................... 15-291
Check (Operation) ....................................... 15-291
Remove and Install ..................................... 15-292
Introduction
The exhaust manifold temperature sensor is screwed
directly into the top of the exhaust manifold between
cylinder 3 and 4 exhaust outlet ports.
Figure 367. Exhaust manifold
temperature sensor location
18. 15 - Engine
84 - Sensor
14 - Exhaust Manifold Temperature
15 - 291 9813/6950-3 15 - 291
Operation
The exhaust manifold temperature sensor measures
the exhaust gas temperature from the engine, before
it reaches the turbocharger. The analogue voltage
signal is 1–4.5V.
Check (Operation)
For the full inspection and testing procedure, refer to
the help files in ServiceMaster.
19. 15 - Engine
84 - Sensor
14 - Exhaust Manifold Temperature
15 - 292 9813/6950-3 15 - 292
Remove and Install
Special Tools
Description Part No. Qty.
Deep Socket 892/12351 1
Before Removal
1. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
Figure 368.
N
A
A Exhaust manifold temperature sensor
Remove
1. Get access to the engine.
2. Disconnect the electrical connector at the
exhaust manifold temperature sensor.
3. Use the special tool to remove the sensor from
the exhaust manifold.
Special Tool: Deep Socket (Qty.: 1)
4. Discard the sealing washer.
The exhaust manifold temperature sensor is a non-
serviceable item. If the sensor is faulty or damaged
it must be renewed.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Renew the sealing washer.
3. Tighten the exhaust manifold temperature
sensor to the correct torque value.
Table 138. Torque Values
Item Nm
N 45
20. 15 - Engine
84 - Sensor
16 - Exhaust Manifold Pressure
15 - 293 9813/6950-3 15 - 293
16 - Exhaust Manifold Pressure
Introduction .................................................. 15-293
Operation ..................................................... 15-294
Check (Operation) ....................................... 15-294
Remove and Install ..................................... 15-295
Introduction
The exhaust manifold pressure sensor also known
as the manifold absolute pressure sensor is a device
that is used to calibrate the fuel delivery on an ECM
(Engine Control Module) Controlled engine.
The sensor is mounted in the rear section of the
rocker cover.
Figure 369.
C
C
C Exhaust manifold pressure sensor
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. 15 - Engine
84 - Sensor
16 - Exhaust Manifold Pressure
15 - 294 9813/6950-3 15 - 294
Operation
The exhaust manifold pressure sensor informs
the ECM (Engine Control Module) of the exhaust
manifold pressure. To attain an accurate and stable
reading the take-off point is piped from the exhaust
manifold between cylinders 3 and 4. This is fed
to a sample chamber in the corner of the rocker
cover where the sensor is screwed directly into the
pressure path.
The sensor produces an analogue signal from
1–4.5V which informs the ECM of the exhaust
manifold pressure. The voltage output proportional to
pressure is 0.5–4.5V.
Check (Operation)
1. For the full inspection and testing procedure,
refer to the help files in ServiceMaster.
23. 15 - Engine
84 - Sensor
16 - Exhaust Manifold Pressure
15 - 295 9813/6950-3 15 - 295
Remove and Install
Special Tools
Description Part No. Qty.
Deep Socket 892/12351 1
Before Removal
1. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
Figure 370.
1
P1
2
1 Exhaust manifold pressure sensor
2 Electrical connector
P1 Sealing washer
Remove
1. Get access to the engine.
2. Disconnect the electrical connector at the
exhaust manifold pressure sensor.
3. Use the special tool to remove the sensor from
the exhaust manifold.
Special Tool: Deep Socket (Qty.: 1)
4. Discard the sealing washer.
The exhaust manifold pressure sensor is a non-
serviceable item. If the sensor is faulty or damaged
it must be renewed.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Renew the sealing washer.
3. Use the special tool to tighten the exhaust
manifold pressure sensor to the correct torque
value.
Table 139. Torque Values
Item Nm
1 22.5
24. 15 - Engine
84 - Sensor
17 - Temperature and Manifold Air Pressure (TMAP)
15 - 296 9813/6950-3 15 - 296
17 - Temperature and Manifold Air
Pressure (TMAP)
Introduction .................................................. 15-296
Operation ..................................................... 15-297
Check (Operation) ....................................... 15-297
Remove and Install ..................................... 15-298
Introduction
The TMAP (Temperature Manifold Air Pressure)
sensor is mounted in a port on top of the inlet
manifold. It measures the inlet manifold boost air
pressure and temperature. The sensor incorporates
a piezo-resistive element and resistor.
Figure 371.
D
D
D TMAPsensor