The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Lowering equipment and releasing pressure before removal, then draining fluid and disconnecting hoses and pipes.
2) Cleaning and replacing filters before installation, then bleeding air from the pump, tightening plugs, and running the engine to circulate oil.
3) Steps for disassembling the pump include draining oil, removing bolts and covers, and pulling parts out carefully. Assembly is the reverse process.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdffujjekdmdmd
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Reinstallation is the reverse of removal. Important steps are cleaning parts, replacing filters, bleeding air from the system, and checking for leaks after startup.
3) The document details the structure of the pump including its main parts and provides diagrams. Disassembly instructions specify cleaning and removing individual components like seals, plates, and shafts. Reassembly follows the reverse order while applying lubricants and torques.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfpwg56547003
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump, including labels and exploded diagrams of the parts.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdff8uejkkdmdm8u
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Disassembly instructions include draining the pump, removing individual parts like the casing, pistons, seals, and plates. Cleaning each part with oil and reapplying lubricant before reassembly is emphasized.
3) Reassembly is the reverse of disassembly, taking care to tighten bolts to the specified torques and replacing seals. Proper cleaning and lubrication of parts is important to prevent damage during installation.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfufjsjekmd8du
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Reinstallation is the reverse of removal. It includes cleaning parts, replacing filters, bleeding air from the system, and checking for leaks after startup.
3) The document then details the structure and components of the main pump, providing a diagram and list. It also provides torque specifications for fasteners and lists recommended tools.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfdujdkksmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump, including labels and exploded diagrams of the parts.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdf8fujsekkdmdme3
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Disassembly instructions include draining the pump, removing individual parts like the casing, pistons, seals, and plates. Cleaning each part with oil and reapplying lubricant during reassembly is emphasized.
3) Reassembly is the reverse of disassembly, taking care to tighten bolts to the specified torques and replacing seals. Proper cleaning and lubrication of parts is important to prevent damage during installation.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdf8dskeddmdd
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Reinstallation is the reverse of removal. It includes cleaning parts, replacing filters, bleeding air from the system, and checking for leaks after startup.
3) The document then details the structure, tools, torque specifications, and procedures for disassembling and reassembling the pump. Disassembly involves removing individual parts like seals, plates, and shafts. Reassembly follows the reverse order while applying lubricants and torques.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump and regulator.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdffujjekdmdmd
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Reinstallation is the reverse of removal. Important steps are cleaning parts, replacing filters, bleeding air from the system, and checking for leaks after startup.
3) The document details the structure of the pump including its main parts and provides diagrams. Disassembly instructions specify cleaning and removing individual components like seals, plates, and shafts. Reassembly follows the reverse order while applying lubricants and torques.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfpwg56547003
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump, including labels and exploded diagrams of the parts.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdff8uejkkdmdm8u
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Disassembly instructions include draining the pump, removing individual parts like the casing, pistons, seals, and plates. Cleaning each part with oil and reapplying lubricant before reassembly is emphasized.
3) Reassembly is the reverse of disassembly, taking care to tighten bolts to the specified torques and replacing seals. Proper cleaning and lubrication of parts is important to prevent damage during installation.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfufjsjekmd8du
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Reinstallation is the reverse of removal. It includes cleaning parts, replacing filters, bleeding air from the system, and checking for leaks after startup.
3) The document then details the structure and components of the main pump, providing a diagram and list. It also provides torque specifications for fasteners and lists recommended tools.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfdujdkksmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump, including labels and exploded diagrams of the parts.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdf8fujsekkdmdme3
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Disassembly instructions include draining the pump, removing individual parts like the casing, pistons, seals, and plates. Cleaning each part with oil and reapplying lubricant during reassembly is emphasized.
3) Reassembly is the reverse of disassembly, taking care to tighten bolts to the specified torques and replacing seals. Proper cleaning and lubrication of parts is important to prevent damage during installation.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdf8dskeddmdd
1) The document provides instructions for removing and installing a hydraulic pump. Key steps include draining the oil, disconnecting hoses and pipes, removing mounting bolts, and lifting out the pump assembly.
2) Reinstallation is the reverse of removal. It includes cleaning parts, replacing filters, bleeding air from the system, and checking for leaks after startup.
3) The document then details the structure, tools, torque specifications, and procedures for disassembling and reassembling the pump. Disassembly involves removing individual parts like seals, plates, and shafts. Reassembly follows the reverse order while applying lubricants and torques.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump and regulator.
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdffujskmd9dokk
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump including the cylinder block, pistons, swash plate, and valves. Disassembly and assembly steps are outlined.
4) The structure of the pump regulator including connecting it during assembly.
Hyundai r140 lc 9 crawler excavator service repair manualfksjksmmde
This document provides instructions for removing and installing a hydraulic pump. It describes removing the pump by draining the oil, disconnecting hoses and pipes, and removing mounting bolts. Installation is the reverse of removal. It also provides details on the pump components, bleeding air from the system, and tightening torques for bolts. Regulator structure and components are also outlined.
Hyundai R145CR-9 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Lowering work equipment, releasing pressure from lines before removal, draining oil from the tank.
2) Disconnecting hoses and pipes, removing mounting bolts, and pulling the pump assembly out of the housing.
3) Reinstallation is done in reverse order, adding new oil and bleeding air from the system before testing.
Hyundai r110 7 crawler excavator service repair manualfhsejkdkmem
This document provides instructions for removing and installing a hydraulic pump.
The key steps for removal are:
1) Draining the oil from the hydraulic tank and piping
2) Disconnecting all hoses and lines connected to the pump
3) Removing mounting bolts and pulling the pump assembly out of the housing
The key steps for installation are:
1) Cleaning and replacing any worn parts like filters or seals
2) Adding oil to the hydraulic tank
3) Bleeding air from the system by loosening vent plugs and running the engine
4) Checking for oil leaks after installation is complete.
The document also provides diagrams and part numbers for the pump components and instructions for
Hyundai r110 7 crawler excavator service repair manualfhsjekkdkem
This document provides instructions for removing and installing a hydraulic pump. It describes:
1. Draining the oil from the hydraulic tank and disconnecting hydraulic lines and hoses before removing mounting bolts and pulling the pump assembly out of the housing.
2. Disassembling the pump by removing swash plate, pistons, seals, and valve plates. Cleaning and inspecting parts is emphasized before reassembly.
3. Reassembling the pump by reversing the disassembly steps and tightening bolts to the specified torques. Bleeding air from the system by loosening plugs is described.
Hyundai R160LC-3 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1. Draining the oil from the hydraulic tank and pump before removal.
2. Disconnecting all hydraulic lines and electrical connections to fully remove the pump assembly.
3. Reversing the removal procedures for installation, including reconnecting all lines, bleeding air from the system, and checking for leaks.
Hyundai R180LC-7 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and disassembling various parts of an excavator travel device. Some of the key steps include:
1. Removing the track shoe assembly, cover, hose, bolts and sprocket to remove the travel device assembly from the excavator.
2. Disassembling the brake valve section and hydraulic motor section by removing parts like the rear flange kit, valve kit, timing plate, pins and bearings.
3. Draining oil from the reduction gear before disassembling parts like the cylinder block, piston assembly, swash plate, shaft and seals.
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. Proper maintenance such as following instructions, using correct tools and parts, cleaning components, and ensuring tight fasteners is important to maximize engine performance and longevity. The document provides an overview of engine operation and maintenance procedures.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the key features of the engines such as their OMEGA combustion bowl design and specifications including power, torque, and idle speeds. Exploded diagrams show the main engine components and assemblies in the DE12, DE12TI, and DE12TIS configurations. General repair instructions are provided to guide proper maintenance techniques.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. The manual includes symbols to indicate maintenance tasks and safety instructions for preventing environmental damage when disposing of waste. It aims to help customers and distributors properly operate and maintain the engines to retain maximum performance over the long term.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdffujskmd9dokk
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, cover, screws, nuts, and other minor parts. The manual provides an exploded diagram of the power unit and an index of the parts to allow technicians to identify replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdffujskmd9dokk
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdffujskmd9dokk
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdffujskmd9dokk
This document is a service manual that provides instructions for safely maintaining Clark forklifts. It discusses identifying information for specific forklift models covered by the manual and how the manual is organized. The document also provides extensive safety guidelines and warnings for maintenance personnel, covering topics like ensuring adequate ventilation, blocking wheels before starting work, disconnecting batteries, and only performing approved modifications. Personnel are instructed to carefully read and understand all safety procedures before working on forklifts.
Clark EPX 16-20S Forklift Service Repair Manual.pdffujskmd9dokk
This document is the service manual for Clark forklift models TMX12-25 and ECX16-18. It provides instructions on using and arranging the manual, which is divided into standardized groups and sections. The manual outlines safety practices and procedures for maintaining the forklifts, including proper lifting, jacking, and blocking of the vehicles. It emphasizes using qualified personnel and following the manufacturer's recommendations to safely conduct maintenance and repairs.
Clark CMP 70 Forklift Service Repair Manual.pdffujskmd9dokk
This document provides instructions for safely maintaining Clark industrial trucks. It outlines 21 safe maintenance practices, such as raising trucks on blocks before working on them, disconnecting batteries, inspecting brakes and other components regularly, and using lifting equipment of the proper capacity when removing heavy components. Technicians are instructed to follow the manufacturer's recommendations and use genuine or approved replacement parts.
More Related Content
Similar to Hyundai R180LC-9 Crawler Excavator Service Repair Manual.pdf
Hyundai R140LC-9 Crawler Excavator Service Repair Manual.pdffujskmd9dokk
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Draining the oil from the hydraulic tank and disconnecting hoses and pipes to remove the pump assembly.
2) Reversing the removal steps for installation, including adding new oil, bleeding air from the system, and checking for leaks.
3) The structure and components of the main pump including the cylinder block, pistons, swash plate, and valves. Disassembly and assembly steps are outlined.
4) The structure of the pump regulator including connecting it during assembly.
Hyundai r140 lc 9 crawler excavator service repair manualfksjksmmde
This document provides instructions for removing and installing a hydraulic pump. It describes removing the pump by draining the oil, disconnecting hoses and pipes, and removing mounting bolts. Installation is the reverse of removal. It also provides details on the pump components, bleeding air from the system, and tightening torques for bolts. Regulator structure and components are also outlined.
Hyundai R145CR-9 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1) Lowering work equipment, releasing pressure from lines before removal, draining oil from the tank.
2) Disconnecting hoses and pipes, removing mounting bolts, and pulling the pump assembly out of the housing.
3) Reinstallation is done in reverse order, adding new oil and bleeding air from the system before testing.
Hyundai r110 7 crawler excavator service repair manualfhsejkdkmem
This document provides instructions for removing and installing a hydraulic pump.
The key steps for removal are:
1) Draining the oil from the hydraulic tank and piping
2) Disconnecting all hoses and lines connected to the pump
3) Removing mounting bolts and pulling the pump assembly out of the housing
The key steps for installation are:
1) Cleaning and replacing any worn parts like filters or seals
2) Adding oil to the hydraulic tank
3) Bleeding air from the system by loosening vent plugs and running the engine
4) Checking for oil leaks after installation is complete.
The document also provides diagrams and part numbers for the pump components and instructions for
Hyundai r110 7 crawler excavator service repair manualfhsjekkdkem
This document provides instructions for removing and installing a hydraulic pump. It describes:
1. Draining the oil from the hydraulic tank and disconnecting hydraulic lines and hoses before removing mounting bolts and pulling the pump assembly out of the housing.
2. Disassembling the pump by removing swash plate, pistons, seals, and valve plates. Cleaning and inspecting parts is emphasized before reassembly.
3. Reassembling the pump by reversing the disassembly steps and tightening bolts to the specified torques. Bleeding air from the system by loosening plugs is described.
Hyundai R160LC-3 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and installing a hydraulic pump. It describes:
1. Draining the oil from the hydraulic tank and pump before removal.
2. Disconnecting all hydraulic lines and electrical connections to fully remove the pump assembly.
3. Reversing the removal procedures for installation, including reconnecting all lines, bleeding air from the system, and checking for leaks.
Hyundai R180LC-7 Crawler Excavator Service Repair Manual.pdfdjfksekmdmdm
The document provides instructions for removing and disassembling various parts of an excavator travel device. Some of the key steps include:
1. Removing the track shoe assembly, cover, hose, bolts and sprocket to remove the travel device assembly from the excavator.
2. Disassembling the brake valve section and hydraulic motor section by removing parts like the rear flange kit, valve kit, timing plate, pins and bearings.
3. Draining oil from the reduction gear before disassembling parts like the cylinder block, piston assembly, swash plate, shaft and seals.
Similar to Hyundai R180LC-9 Crawler Excavator Service Repair Manual.pdf (7)
Daewoo Doosan DE12TIS Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo Doosan DE12TI Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. Proper maintenance such as following instructions, using correct tools and parts, cleaning components, and ensuring tight fasteners is important to maximize engine performance and longevity. The document provides an overview of engine operation and maintenance procedures.
Daewoo Doosan DE12T Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the key features of the engines such as their OMEGA combustion bowl design and specifications including power, torque, and idle speeds. Exploded diagrams show the main engine components and assemblies in the DE12, DE12TI, and DE12TIS configurations. General repair instructions are provided to guide proper maintenance techniques.
Daewoo Doosan DE12 Diesel Engine Service Repair Manual.pdffujskmd9dokk
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. The manual includes symbols to indicate maintenance tasks and safety instructions for preventing environmental damage when disposing of waste. It aims to help customers and distributors properly operate and maintain the engines to retain maximum performance over the long term.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdffujskmd9dokk
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, listed with their part numbers and the quantity required. Key components included are the power unit enclosure, rear doors, cover, screws, nuts, and other minor parts. The manual provides an exploded diagram of the power unit and an index of the parts to allow technicians to identify replacement parts.
Crown LP3020 Lift Truck Service Repair Manual.pdffujskmd9dokk
The document provides maintenance information for LP3010/3020 series trucks. It contains sections on lubrication and adjustment, hydraulics, the drive unit, electrics, brakes, steering, lifting mechanisms, cylinders, and electrical diagrams. The document includes safety notes, inspection and maintenance schedules, repair and replacement procedures, and diagrams. Revisions provide corrections and additions to the text as well as changes to diagrams, tables, and descriptions.
Crown GPC2000 Series Lift Truck Parts Catalogue Manual.pdffujskmd9dokk
This document provides lubrication information for a parts manual. It lists the recommended lubricants and their specifications for various components of the product. Grease type 2 is recommended for bearings and grease type 2-P for ball bearings. Mobilex 00-200 is suitable for lower operating temperatures, while Mobilex 005-200 is recommended for higher temperatures.
Clark TMX12-25 Forklift Service Repair Manual.pdffujskmd9dokk
This document is a service manual that provides instructions for safely maintaining Clark forklifts. It discusses identifying information for specific forklift models covered by the manual and how the manual is organized. The document also provides extensive safety guidelines and warnings for maintenance personnel, covering topics like ensuring adequate ventilation, blocking wheels before starting work, disconnecting batteries, and only performing approved modifications. Personnel are instructed to carefully read and understand all safety procedures before working on forklifts.
Clark EPX 16-20S Forklift Service Repair Manual.pdffujskmd9dokk
This document is the service manual for Clark forklift models TMX12-25 and ECX16-18. It provides instructions on using and arranging the manual, which is divided into standardized groups and sections. The manual outlines safety practices and procedures for maintaining the forklifts, including proper lifting, jacking, and blocking of the vehicles. It emphasizes using qualified personnel and following the manufacturer's recommendations to safely conduct maintenance and repairs.
Clark CMP 70 Forklift Service Repair Manual.pdffujskmd9dokk
This document provides instructions for safely maintaining Clark industrial trucks. It outlines 21 safe maintenance practices, such as raising trucks on blocks before working on them, disconnecting batteries, inspecting brakes and other components regularly, and using lifting equipment of the proper capacity when removing heavy components. Technicians are instructed to follow the manufacturer's recommendations and use genuine or approved replacement parts.
Clark CMP 60 Forklift Service Repair Manual.pdffujskmd9dokk
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark CMP 50 Forklift Service Repair Manual.pdffujskmd9dokk
This document is the service manual for Clark Material Handling Company's CMP50/60/70 trucks. It contains safety instructions for maintaining the trucks, including raising them on blocks, disconnecting batteries, and checking for fuel and electrical system issues. The manual is arranged by topic groups and sections for locating specific maintenance and repair procedures.
Caterpillar Cat D400E II EJECTOR TRUCK (Prefix APF) Service Repair Manual (AP...fujskmd9dokk
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety notices warn of potential injury from compressed springs and ensure clean and contamination-free assembly.
Caterpillar Cat 336F L Excavator (Prefix YFD) Service Repair Manual (YFD00001...fujskmd9dokk
This document provides instructions for disassembling the travel motor on a 336F excavator. It involves removing over 30 components in 27 steps, including the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include bolts, nuts, washers, threaded rods, eyebolts, drivers, pullers, and other specialized tooling. Detailed illustrations are provided to show each component and step in the disassembly process. Safety notices advise wearing protective equipment when removing or releasing parts under spring force.
Caterpillar Cat 336F L Excavator (Prefix DSW) Service Repair Manual (DSW00001...fujskmd9dokk
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety notices advise wearing protective equipment when compressing springs or releasing pressurized components during disassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Digital Fleet Management - Why Your Business Need It?
Hyundai R180LC-9 Crawler Excavator Service Repair Manual.pdf
1.
2.
3. 8-7
1. REMOVAL AND INSTALL
1. REMOVAL AND INSTALL
REMOVAL
REMOVAL
Lower the work equipment to the ground
and stop the engine.
Operate the control levers and pedals
several times to release the remaining
pressure in the hydraulic piping
Loosen the breather slowly to release the
pressure inside the hydraulic tank.
Escaping fluid under pressure can
Escaping fluid under pressure can
penetrate the skin causing serious injury.
penetrate the skin causing serious injury.
Loosen the drain plug under the hydraulic
tank and drain the oil from the hydraulic
tank.
·Hydraulic tank quantity : 124ℓ(32.8 U.S.
gal)
Remove socket bolts (11) and disconnect
hoses (1,2).
Disconnect pilot line hoses (5, 6, 7, 8, 9,
10).
Remove socket bolts (12) and disconnect
pump suction pipe (4).
When pump suction tube is disconnect-
ed, the oil inside the piping will flow out,
so catch it in oil pan.
Sling the pump assembly and remove the
pump mounting bolts.
· Weight : 100 kg (220 lb)
Pull out the pump assembly from
housing.
When removing the pump assembly,
check that all the hoses have been
disconnected.
GROUP 3 PUMP DEVICE
GROUP 3 PUMP DEVICE
12
1
11
4
2
3
A1
A2
B1
Pi1
Dr
B3
A3
Psv
Pi2
5
6 7
8
9
10
1)
1)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
※
(8)
※
13031GE18
14098MP01
14098MP02
4. 8-8
INSTALL
INSTALL
Carry out installation in the reverse order to
removal.
Remove the suction strainer and clean it.
Replace return filter with new one.
Remove breather and clean it.
After adding oil to the hydraulic tank to the
specified level.
Bleed the air from the hydraulic pump.
Remove the air vent plug (2EA).
Tighten plug lightly.
Start the engine, run at low idling, and
check oil come out from plug.
Tighten plug.
Start the engine, run at low idling (3~5
minutes) to circulate the oil through the
system.
Confirm the hydraulic oil level and check
the hydraulic oil leak or not.
2)
2)
(1)
(2)
(3)
(4)
(5)
(6)
①
②
③
④
(7)
(8)
6. 8-10
TOOLS AND TIGHTENING TORQUE
TOOLS AND TIGHTENING TORQUE
Tools
Tools
The tools necessary to disassemble/reassemble the pump are shown in the follow list.
2)
2)
(1)
(1)
Tool name & size Part name
Name B
Hexagon socket
head bolt
PT plug
(PT thread)
PO plug
(PF thread)
Hexagon socket
head setscrew
4 M 5 BP-1/16 - M 8
5 M 6 BP-1/8 - M10
6 M 8 BP-1/4 PO-1/4 M12, M14
8 M10 BP-3/8 PO-3/8 M16, M18
17 M20, M22 BP-1 PO-1, 1 1/4, 1 1/2 -
- Hexagon bolt Hexagon nut
VP plug
(PF thread)
19 M12 M12 VP-1/4
24 M16 M16 -
27 M18 M18 VP-1/2
30 M20 M20 -
36 - - VP-3/4
Adjustable angle wrench Medium size, 1 set
Screw driver Minus type screw driver, Medium size, 2 sets
Hammer Plastic hammer, 1 set
Pliers For snap ring, TSR-160
Steel bar Steel bar of key material approx. 10×8×200
Torque wrench Capable of tightening with the specified torques
Allen wrench
B
Double ring spanner,
socket wrench, double (single)
open end spanner
B
8. 8-12
DISASSEMBLY
DISASSEMBLY
Select place suitable to disassembling.
Select clean place.
Spread rubber sheet, cloth or so on on
overhaul workbench top to prevent parts
from being damaged.
Remove dust, rust, etc, from pump
surfaces with cleaning oil or so on.
Remove drain port plug (468) and let oil
out of pump casing (front and rear pump).
3)
3)
Place pump horizontally on workbench
with its regulator-fitting surface down and
separate pump casing (271) from valve
block (312).
Before bringing this surface down, spread
rubber sheet on workbench without fail to
prevent this surface from being damaged.
(1)
※
※
(2)
(3)
(6)
※
Loosen hexagon socket head bolts (401)
which tighten swash plate support (251),
pump casing (271) and valve block (312).
If gear pump and so on are fitted to rear
face of pump, remove them before
starting this work.
(5)
※
Remove hexagon socket head bolts (412,
413) and remove regulator.
(4)
(210-7) MP01
(210-7) MP02
9. 8-13
Pull cylinder block (141) out of pump
casing (271) straightly over drive shaft
(111). Pull out also pistons (151), set
plate (153), spherical bush (156) and
cylinder springs (157) simultaneously.
Take care not to damage sliding surfaces
of cylinder, spherical bushing, shoes,
swash plate, etc.
(7)
※
Remove hexagon socket head bolts (406)
and then seal cover (F, 261).
Fit bolt into pulling out tapped hole of seal
cover (F), and cover can be removed
easily.
Since oil seal is fitted on seal cover (F),
take care not to damage it in removing
cover.
Remove hexagon socket head bolts (408)
and then seal cover (R, 262).
In case fitting a gear pump, first, remove
gear pump.
Tapping lightly fitting flange section of
swash plate support (251) on its pump
casing side, separate swash plate support
from pump casing.
(8)
※
※
(9)
Remove shoe plate (211)and swash plate
(212) from pump casing (271).
(11)
(10)
(210-7) MP03
(210-7) MP04
(210-7) MP05
(210-7) MP06
10. 8-14
If necessary, remove stopper (L, 534),
stopper (S, 535), servo piston (532) and
tilting pin (531) from pump casing (271),
and needle bearing (124) and splined
coupling (114) from valve block (312).
In removing tilting pin, use a protector to
prevent pin head from being damaged.
Since loctite is applied to fitting areas of
tilting pin and servo piston, take care not
to damage servo piston.
Do not remove needle bearing as far as
possible, except when it is considered to
be out of its life span.
Do not loosen hexagon nuts of valve
block and swash plate support.
If loosened, flow setting will be changed.
(14)
※
※
※
※
Remove valve plates (313, 314) from
valve block (312).
These may be removed in work (6).
(13)
※
Tapping lightly shaft ends of drive shafts
(111, 113) with plastic hammer, take out
drive shafts from swash plate supports.
(12)
(210-7) MP07
(210-7) MP08
11. 8-15
ASSEMBLY
ASSEMBLY
Fo r r e a s s e m bl i n g r eve r s e t h e
disassembling procedures, paying
attention to the following items.
Do not fail to repair the parts damaged
during disassembling, and prepare
replacement parts in advance.
Clean each part fully with cleaning oil
and dry it with compressed air.
Do not fail to apply clean working oil to
sliding sections, bearings, etc. before
assembling them.
In principle, replace seal parts, such as
O-rings, oil seals, etc.
For fitting bolts, plug, etc., prepare a
torque wrench or so on, and tighten them
with torques shown in page 8-11, 12.
For the double-pump, take care not to
mix up parts of the front pump with those
of the rear pump.
(1)
4)
4)
①
②
③
④
⑤
⑥
Fit swash plate support (251) to pump
casing (271), tapping the former lightly
with a hammer.
After servo piston, tilting pin, stopper (L)
and stopper (S) are removed, fit them
soon to pump casing in advance for
reassembling.
In tightening servo piston and tilting pin,
use a protector to prevent tilting pin head
and feedback pin from being damaged.
In addition, apply loctite (Medium
strength) to their threaded sections.
(2)
※
※
(210-7) MP09
12. 8-16
Place pump casing with its regulator fitting
surface down, fit tilting bush of swash
plate to tilting pin (531) and fit swash plate
(212) to swash plate support (251)
correctly.
Confirm with fingers of both hands that
swash plate can be removed smoothly.
Apply grease to sliding sections of swash
plate and swash plate support, and drive
shaft can be fitted easily.
(3)
※
※
Assemble piston cylinder subassembly
〔c y l i n d e r bl o ck ( 1 4 1 ) , p i s t o n
subassembly (151, 152), set plate (153),
spherical bush (156), spacer (158) and
cylinder spring (157)〕.
Fit spline phases of retainer and cylinder.
Then, insert piston cylinder subassembly
into pump casing.
(6)
Assemble seal cover (F, 261) to pump
casing (271) and fix it with hexagon
socket head bolts (406).
Apply grease lightly to oil seal in seal
cover (F).
Assemble oil seal, taking full care not to
damage it.
For tandem type pump, fit rear cover
(263) and seal cover (262) similarly.
(5)
※
※
※
To swash plate support (251), fit drive
shaft (111) set with bearing (123), bearing
spacer (127) and snap ring (824).
Do not tap drive shaft with hammer or so
on.
Assemble them into support, tapping
outer race of bearing lightly with plastic
hammer.
Fit them fully, using steel bar or so on.
(4)
※
※
(210-7) MP10
(210-7) MP11
(210-7) MP12
(210-7) MP13
13. 8-17
Fit valve plate (313) to valve block (312),
entering pin into pin hole.
Take care not to mistake suction / delivery
directions of valve plate.
(7)
※
Putting feedback pin of tilting pin into
feedback lever of regulator, fit regulator
and tighten hexagon socket head bolts
(412, 413).
Take care not to mistake regulator of front
pump for that of rear pump.
(9)
※
Fit valve block (312) to pump casing (271)
and tighten hexagon socket head bolts
(401).
At first assemble this at rear pump side,
and this work will be easy.
Take care not to mistake direction of valve
block.
Clockwise rotation (Viewed from input
shaft side) - Fit block with regulator up
and with delivery flange left, viewed from
front side.
Counter clockwise rotation (Viewed from
input shaft side) - Fit block with delivery
flange right, viewed from front side.
(8)
※
※
※
※
Fit drain port plug (468).
This is the end of reassembling procedures.
(10)
(210-7) MP14
(210-7) MP16
(210-7) MP17
14. 8-18
3. REGULATOR
3. REGULATOR
STRUCTURE
STRUCTURE (1/2)
1)
1)
412 876 874
A
B
755
858
614
615
613
611
A
B
VIEW C (FRONT)
897
612
641 730 643 708 644 645 646
SECTION B-B
728 924 801
438
P2
KR38-9N37 (FRONT)
KR38-9N35 (REAR)
A
B
413 438
496 724 725
D
D
VIEW C (REAR)
413 438
438
722
496 724 725
079 735 722 466
755
496
753
P1
a
875
P1
a
405
699
Pi
735
Pi
Pi
C
753
Pi
436 436
656
SECTION D-D(REAR)
16092MP04
15. 8-19
REGULATOR
REGULATOR (2/2)
734 653 654 836 651 652 601 624 629 630
655
641
814
898
631
732
628
756
763
887
626
625
733
622
621 623 754
802
627
SECTION A-A
14092MP05
079 EPPR valve assembly
405 Hexagon socket screw (R)
412 Hexagon socket screw
413 Hexagon socket screw
436 Hexagon socket screw
438 Hexagon socket screw
466 Plug (R)
496 Plug
601 Casing
611 Feed back lever
612 Lever (1)
613 Lever (2)
614 Fulcrum plug
615 Adjust plug
621 Compensator piston
622 Piston case
623 Compensator rod
624 Spring seat (C)
625 Outer spring
626 Inner spring
627 Adjust stem (C)
628 Adjust screw (C)
629 Cover (C)
630 Lock nut
631 Sleeve, Pf
641 Pilot cover
643 Pilot piston
644 Spring seat (Q)
645 Adjust stem (Q)
646 Pilot spring
651 Sleeve
652 Spool
653 Spring seat
654 Return spring
655 Set spring
656 Block cover (F)
699 Valve casing (R)
708 O-ring
722 O-ring
724 O-ring
725 O-ring
728 O-ring
730 O-ring
732 O-ring
733 O-ring
734 O-ring
735 O-ring
753 O-ring (R)
754 O-ring
755 O-ring
756 O-ring
763 O-ring
801 Nut
802 Nut
814 Snap ring
836 Snap ring
858 Snap ring
874 Pin
875 Pin
876 Pin
887 Pin
897 Pin
898 Pin
924 Set screw
16. 8-20
TOOLS AND TIGHTENING TORQUE
TOOLS AND TIGHTENING TORQUE
Tools
Tools
The tools necessary to disassemble/reassemble the pump are shown in the follow list.
2)
2)
(1)
(1)
Tool name & size Part name
Name B
Hexagon socket
head bolt
PT plug
(PT thread)
PO plug
(PF thread)
Hexagon socket
head setscrew
4 M5 BP-1/16 - M 8
5 M6 BP-1/8 - M10
6 M8 BP-1/4 PO-1/4 M12, M14
-
Hexagon head
bolt
Hexagon nut
VP plug
(PF thread)
6 M 8 M 8 -
Adjustable angle wrench Small size, Max 36 mm
Screw driver Minus type screw driver, Medium size, 2 sets
Hammer Plastic hammer, 1 set
Pliers For snap ring, TSR-160
Steel bar 4×100 mm
Torque wrench Capable of tightening with the specified torques
Pincers -
Bolt M4, Length : 50 mm
B
Allen wrench
B
Double ring spanner,
socket wrench, double
(single) open end spanner
18. 8-22
DISASSEMBLY
DISASSEMBLY
Since the regulator consists of small
precision finished parts, disassembly and
assembly are rather complicated.
For this reason, replacement of a regulator
assembly is recommended, unless there is
a special reason, but in case disassembly is
necessary for an unavoidable reason, read
through this manual to the end before
starting disassembly.
Choose a place for disassembly.
Choose a clean place.
Spread rubber sheet, cloth, or so on on
top of work-bench to prevent parts from
being damaged.
Remove dust, rust, etc. from surfaces of
regulator with clean oil.
(1)
※
※
(2)
3)
3)
Remove hexagon socket head screw
(438) and remove cover (C,629)
Cover (C) is fitted with adjusting screw
(C, 628), adjusting ring (C, 627), lock nut
(630), hexagon nut (801) and adjusting
screw (924).
Do not loosen these screws and nuts.
If they are loosened, adjusted pressure-
flow setting will vary.
(4)
※
※
Remove hexagon socket head screw
(412, 413) and remove regulator main
body from pump main body.
Take care not to lose O-ring.
(3)
※
(210-7) REG01
(210-7) REG02
19. 8-23
Remove locking ring (858) and take out
fulcrum plug (614) and adjusting plug
(615).
Fulcrum plug (614) and adjusting plug
(615) can easily be taken out with M6 bolt.
(8)
※
Remove snap ring (814) and take out
spring seat (653), return spring (654) and
sleeve (651).
Sleeve (651) is fitted with snap ring (836).
When removing snap ring (814), return
spring (654) may pop out.
Take care not to lose it.
(7)
※
※
Remove hexagon socket head screws
(436, 438) and remove pilot cover (641).
After removing pilot cover, take out set
spring (655) from pilot section.
(6)
After removing cover (C, 629) subassembly,
take out outer spring (625), inner spring
(626) and spring seat (C, 624) from
compensating section.
Then draw out adjusting ring (Q, 645),
pilot spring (646) and spring seat (644)
from pilot section.
Adjusting ring (Q,645) can easily be
drawn out with M4 bolt.
(5)
※
(210-7) REG03
(210-7) REG04
(210-7) REG05
(210-7) REG06
20. 8-24
Draw out pin (874) and remove feedback
lever (611).
Push out pin (874, 4 mm in dia.) from
above with slender steel bar so that it may
not interfere with lever (1, 612).
(10)
Remove lever (2, 613). Do not draw out
pin (875).
Work will be promoted by using pincers or
so on.
(9)
※
(210-7) REG07
(210-7) REG08
(210-7) REG09
(210-7) REG10
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. 8-25
Remove lever (1, 612). Do not draw out
pin (875).
Draw out pilot piston (643) and spool
(652).
D r a w o u t p i s t o n c a s e ( 6 2 2 ) ,
compensating piston (621) and
compensating rod (623).
Piston case (622) can be taken out by
pushing compensating rod (623) at
opposite side of piston case.
This completes disassembly.
(11)
(12)
(13)
※
23. 8-26
ASSEMBLY
ASSEMBLY
For assembly, reverse disassembly
procedures, but pay attention to the
following items.
Always repair parts that were scored at
disassembly.
Get replacement parts ready beforehand.
Mixing of foreign matter will cause
malfunction.
Therefore, wash parts well with cleaning
oil, let them dry with jet air and handle
them in clean place.
Always tighten bolts, plugs, etc. to their
specified torques.
Do not fail to coat sliding surfaces with
clean hydraulic oil before assembly.
Replace seals such as O-ring with new
ones as a rule.
(1)
①
②
③
④
⑤
4)
4)
Spool
Feedback lever
Put compensating rod (623) into
compensating hole of casing (601).
Put pin force-fitted in lever (1, 612) into
groove of compensating rod and fit lever
(1) to pin force-fitted in casing.
(2)
(3)
Fit spool (652) and sleeve (651) into hole
in spool of casing.
Confirm that spool and sleeve slide
smoothly in casing without binding.
Pay attention to orientation of spool.
(4)
※
※
(210-7) 8-27
24. 8-27
Lever (1) side Lever (2) side
(fulcrum plug of
adjusting plug side)
Fit return spring (654) and spring seat
(653) into spool hole and attach snap ring
(814).
(10)
Fit fulcrum plug (614) so that pin force-
fitted in fulcrum plug (614) can be put into
pin hole of lever (2).
Then fix locking ring (858).
Insert adjusting plug (615) and fit locking
ring.
Take care not to mistake inserting holes
for fulcrum plug and adjusting plug.
At this point in time move feedback lever
to confirm that it has no large play and is
free from binding.
(8)
(9)
※
Put pilot piston (643) into pilot hole of
casing.
Confirm that pilot piston slides smoothly
without binding.
Put pin force-fitted in lever (2, 613) into
groove of pilot piston.
Then fix lever (2).
(6)
※
(7)
Fit feedback lever (611), matching its pin
hole with pin hole in spool.
Then insert pin (874).
Insert pin in feedback lever a little to ease
operation.
Take care not to mistake direction of
feedback lever.
(5)
※
※
(210-7) 8-28
(210-7) REG11
(210-7) REG12
(210-7) REG13
25. 8-28
Install cover (C, 629) fitted with adjusting
screws (628), adjusting ring (C, 627), lock
nut (630), hexagon nut (801) and
adjusting screw (924).
Then tighten them with hexagonal socket
head screws (438).
This completes assembly.
(13)
Put spring seat (644), pilot spring (646)
and adjusting ring (Q, 645) into pilot hole.
Then fix spring seat (624), inner spring
(626) and outer spring (625) into
compensating hole.
When fitting spring seat, take care not to
mistake direction of spring seat.
(12)
※
Fit set spring (655) to spool hole and put
compensating piston (621) and piston
case (622) into compensating hole.
Fit pilot cover (641) and tighten it with
hexagonal socket head screws (436,
438).
(11)
(210-7) REG14
(210-7) REG15
(210-7) REG16