The document provides descriptions and repair procedures for a planetary gear axle. It has the following key points:
1. The planetary gear axle has an axle housing containing two final drive assemblies, each with a planetary gear unit that increases torque to the drive wheels.
2. Operation involves the differential rotating the axle shafts and sun gears, which rotate planetary pinions to turn the planetary spiders and hub, driving the wheels while the ring gear remains stationary.
3. Repair procedures include removing the drive wheels, draining fluids, disconnecting lines and shafts, and disassembling components like the planetary gear carrier, ring gear and hub assemblies. Detailed steps are provided for each part.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfdujjdfjekmemm
The document provides descriptions and repair procedures for a planetary gear axle. It describes the components of the axle, including the axle housing, final drive assemblies, planetary gear units, axle shafts, sun gears, ring gears, planetary pinions, and carrier. It then gives steps to disassemble the axle, including removing wheels, draining fluid, and separating the planetary gear carrier, ring gear, and wheel hub. Reassembly procedures are also provided.
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualusuejjskkemme
The document provides descriptions and repair procedures for a planetary gear axle assembly. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio and increases torque to the drive wheels. The assembly includes components like an axle housing, axle shafts, sun gears, planetary gears, ring gears, and a differential. The repair section outlines removing and disassembling the axle components, inspecting and replacing worn parts, and cleaning procedures to prepare components for reassembly. Welding is not recommended for repair.
Hyster p005 (h4.0 ft5 europe) forklift service repair manualfusjfjskekmem
1. The document provides repair procedures for the drive axle and differential assembly of a lift truck. It describes how to remove and disassemble the drive axle, clean and inspect parts, and reassemble and install the drive axle.
2. The procedures include draining oil, removing wheels and shafts, disassembling planetary gears and needle bearings, cleaning parts, and inspecting gears, bearings, and shafts for wear or damage.
3. Detailed steps are provided for reassembling the planetary gears with grease, installing parts in the differential housing, mounting the drive axle, filling with oil, and testing operation upon completion.
Hyster a216 (j40 xm2) forklift service repair manualfksefkskemm
This document provides repair procedures for the differential, speed reducer, drive axle, and axle mounts of a lift truck. It describes the components and their assembly. The main steps are:
1. Remove the drive unit assembly by taking off the axle mounts, draining fluid, and sliding it out.
2. Disassemble the components like removing gears, bearings, and separating the housings.
3. Clean all parts using solvent and air dry them.
4. Inspect parts for wear and damage.
5. Reassemble following the reverse order, making sure to properly align components and apply correct torque to fasteners.
Hyster a216 (j60 xm2) forklift service repair manualfjjskefkskem
The document provides descriptions and repair procedures for the differential, speed reducer, drive axle, and axle mounts of a lift truck. It describes the components of the drive unit assembly and how it is fastened to the frame. The speed reducer and differential are assembled as a single unit with gears that transfer power. The repair section provides steps to remove, disassemble, clean, inspect, and reassemble the components, including removing the drive unit assembly from the frame and disassembling the differential housing.
The document provides instructions for repairing various components of a lift truck including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant before removing the radiator, and notes the need to add coolant after installation. Safety warnings are provided throughout regarding putting the lift truck on blocks and adding additional blocks when removing heavy components to maintain stability.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfusjefjskefksem
This document provides descriptions and repair procedures for a planetary gear axle. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The document describes the components of the axle, including the differential, brakes, sun gear, planetary gears, ring gear, and hub. It then provides step-by-step instructions to disassemble the axle housing, planetary gear carrier, ring gear assembly, and wheel hub.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfdujsjefjskekmsme
This document provides descriptions and repair procedures for a planetary gear axle. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The document describes the components of the axle, including the differential, brakes, sun gear, planetary gears, ring gear, and hub. It then provides step-by-step instructions to disassemble the axle housing, planetary gear carrier, ring gear assembly, and wheel hub.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfdujjdfjekmemm
The document provides descriptions and repair procedures for a planetary gear axle. It describes the components of the axle, including the axle housing, final drive assemblies, planetary gear units, axle shafts, sun gears, ring gears, planetary pinions, and carrier. It then gives steps to disassemble the axle, including removing wheels, draining fluid, and separating the planetary gear carrier, ring gear, and wheel hub. Reassembly procedures are also provided.
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualusuejjskkemme
The document provides descriptions and repair procedures for a planetary gear axle assembly. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio and increases torque to the drive wheels. The assembly includes components like an axle housing, axle shafts, sun gears, planetary gears, ring gears, and a differential. The repair section outlines removing and disassembling the axle components, inspecting and replacing worn parts, and cleaning procedures to prepare components for reassembly. Welding is not recommended for repair.
Hyster p005 (h4.0 ft5 europe) forklift service repair manualfusjfjskekmem
1. The document provides repair procedures for the drive axle and differential assembly of a lift truck. It describes how to remove and disassemble the drive axle, clean and inspect parts, and reassemble and install the drive axle.
2. The procedures include draining oil, removing wheels and shafts, disassembling planetary gears and needle bearings, cleaning parts, and inspecting gears, bearings, and shafts for wear or damage.
3. Detailed steps are provided for reassembling the planetary gears with grease, installing parts in the differential housing, mounting the drive axle, filling with oil, and testing operation upon completion.
Hyster a216 (j40 xm2) forklift service repair manualfksefkskemm
This document provides repair procedures for the differential, speed reducer, drive axle, and axle mounts of a lift truck. It describes the components and their assembly. The main steps are:
1. Remove the drive unit assembly by taking off the axle mounts, draining fluid, and sliding it out.
2. Disassemble the components like removing gears, bearings, and separating the housings.
3. Clean all parts using solvent and air dry them.
4. Inspect parts for wear and damage.
5. Reassemble following the reverse order, making sure to properly align components and apply correct torque to fasteners.
Hyster a216 (j60 xm2) forklift service repair manualfjjskefkskem
The document provides descriptions and repair procedures for the differential, speed reducer, drive axle, and axle mounts of a lift truck. It describes the components of the drive unit assembly and how it is fastened to the frame. The speed reducer and differential are assembled as a single unit with gears that transfer power. The repair section provides steps to remove, disassemble, clean, inspect, and reassemble the components, including removing the drive unit assembly from the frame and disassembling the differential housing.
The document provides instructions for repairing various components of a lift truck including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant before removing the radiator, and notes the need to add coolant after installation. Safety warnings are provided throughout regarding putting the lift truck on blocks and adding additional blocks when removing heavy components to maintain stability.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfusjefjskefksem
This document provides descriptions and repair procedures for a planetary gear axle. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The document describes the components of the axle, including the differential, brakes, sun gear, planetary gears, ring gear, and hub. It then provides step-by-step instructions to disassemble the axle housing, planetary gear carrier, ring gear assembly, and wheel hub.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfdujsjefjskekmsme
This document provides descriptions and repair procedures for a planetary gear axle. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The document describes the components of the axle, including the differential, brakes, sun gear, planetary gears, ring gear, and hub. It then provides step-by-step instructions to disassemble the axle housing, planetary gear carrier, ring gear assembly, and wheel hub.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfujjdfjkwskemme
The document provides descriptions and repair procedures for a planetary gear axle. It describes the components of the axle, including the axle housing, two final drive assemblies which contain planetary gear units, differential, and brake assemblies. It then provides detailed steps for disassembling, inspecting, repairing, cleaning, and reassembling the various components of the planetary gear axle.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfjsekqazxkdmmem
This document provides descriptions and repair procedures for a planetary gear axle. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The document describes the components of the axle, including the differential, brakes, sun gear, planetary gears, ring gear, and hub. It then provides step-by-step instructions to disassemble the axle housing, planetary gear carrier, ring gear assembly, and wheel hub.
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualfujsjefjskekemm
The document provides descriptions and repair procedures for a planetary gear axle assembly. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio and increases torque to the drive wheels. The assembly includes an axle housing, axle shafts, sun gears, planetary gears, ring gears, and differentials. The repair section provides steps to disassemble, inspect, repair, clean, and reassemble the various components. Welding is not permitted and worn parts must be replaced. Ground metal surfaces require solvent cleaning only while other parts can be cleaned in hot alkaline solutions.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfusjfjskekmem
The document provides information about repairing a planetary gear axle. It describes the components of the axle, including the axle housing, two final drive assemblies that contain planetary gear units, differential, and service/parking brakes. The operation of the planetary gearing is explained. Repair procedures are outlined for disassembling, inspecting, cleaning, and replacing worn parts. Welding is not recommended for repair. Ground metal parts require solvent cleaning only.
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualfusjjjsekkekm
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies, a differential, and service/parking/auxiliary brake assemblies.
2) Each final drive assembly is a planetary gear unit that changes the final drive ratio to increase torque to the drive wheels. It includes components like an axle shaft, sun gear, ring gear hub, planetary pinions, and a carrier.
3) The repair process involves removing the wheels, draining fluids, disconnecting brake and drive components, and then disassembling the individual parts like the planetary carrier, ring gear hub, and wheel hub to access and replace components. Proper support and safety precautions are
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualusjfjkememe
The document provides descriptions and repair procedures for a planetary gear axle assembly. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The operation section describes how the differential and sun gears rotate the axle shafts and planetary gears to turn the wheels. The repair section gives instructions for disassembling, cleaning, inspecting, and replacing worn parts before reassembly. Safety warnings are provided throughout regarding lifting heavy components and handling brake dust.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfusjejfskekemm
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies that are planetary gear units to increase torque to the drive wheels.
2) It provides an overview of the main components - axle shafts, sun gears, planetary pinions, planetary gear carriers, ring gears, and differentials. Service and parking brakes are also installed.
3) The operation section explains how the differential rotation causes the axle shafts and sun gears to rotate, turning the planetary pinions which rotate the planetary spiders and drive wheels, while the ring gear and hub do not rotate.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfjsekkdmme
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies that are planetary gear units to increase torque to the drive wheels.
2) It provides diagrams and descriptions of the key components, including the axle shafts, sun gears, planetary pinions, planetary gear carriers, ring gears, and differentials.
3) The repair process is outlined, beginning with removing the wheels and tires, then draining fluids before disassembling the various components like the planetary gear carriers, ring gears, and wheel hubs. Safety warnings are provided throughout.
Hyster d024 (s7.0 ft europe) forklift service repair manualfjjskefkskem
This document provides instructions for removing and repairing a drive axle, differential, and wet disc brakes on a service vehicle. It describes removing the drive axle by draining fluids, disconnecting lines and hoses, and removing mounting hardware. It then details disassembling the planetary gear assembly within the drive axle by removing retaining rings, gears, seals, and bearings. Finally, it outlines disassembling the wet disc brakes by removing mounting screws, pistons, springs, plates, and discs.
Hyster h007 (h170 hd) forklift service repair manualfjsjfjskeksmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how the planetary axles operate and provides instructions for identifying the exact axle model. It then provides steps for disassembling the planetary axle assembly including draining lubricant, removing brake drums, planetary spiders, pinion gears, ring gears, wheel hubs and bearings.
Hyster h007 (h190 hd) forklift service repair manualfjskekdmmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how to disassemble the planetary axle assembly, including draining lubricant, removing wheels and brake drums, and removing the planetary spider and gearing components.
Hyster h007 (h210 hd) forklift service repair manualfjskekdmmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how the planetary axles operate and provides instructions for identifying the exact axle model. It then provides steps for disassembling the planetary axle assembly including draining lubricant, removing brake drums, planetary spiders, pinion gears, ring gears, wheel hubs and bearings.
Hyster h007 (h280 hd) forklift service repair manualfjsekqazxkdmmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how to disassemble the planetary axle assembly, including draining lubricant, removing wheels and brake drums, and removing the planetary spider and gearing components.
Hyster h007 (h230 hd) forklift service repair manualfjsjfjskeksmem
The document provides descriptions and repair procedures for a planetary gear axle. It describes the components of the axle including the hypoid gearing, planetary spur gearing, and wheel hub assemblies. The procedures describe how to disassemble the wheel ends, planetary spider and gearing assembly, dry brakes, and other components for inspection or replacement of parts. Detailed diagrams are provided to identify the components.
Hyster f117 (h50.00 xm 16ch europe) forklift service repair manualfsefkksefmme
This document provides repair procedures for a differential assembly. It describes removing the differential carrier from the axle housing and then disassembling the differential carrier. The procedures cover removing the differential and ring gear assembly, drive pinion and pinion carrier from the differential carrier housing. Detailed steps are provided to properly support the vehicle, drain oil, disconnect driveline components, and remove fasteners holding parts together. Safety warnings are included to prevent injury when using jack stands and mallets during the repair process.
Hyster f117 (h52.00 xm 16ch europe) forklift service repair manualfsefkksefmme
This document provides repair procedures for a differential assembly. It describes removing the differential carrier from the axle housing and then disassembling the differential carrier. The procedures cover removing the differential and ring gear assembly, drive pinion and pinion carrier from the differential carrier housing. Detailed steps are provided to disassemble the differential and ring gear assembly. Safety warnings and cautions are included throughout regarding properly supporting the vehicle, using appropriate tools to avoid damage, and marking parts for reassembly.
Hyster a917 (h900 hds) forklift service repair manualfujsjfjksekem
This document provides repair procedures for differentials. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures explain how to remove the differential carrier from the axle housing, disassemble the differential and ring gear assembly, and remove the drive pinion and pinion carrier from the differential carrier. Detailed steps are provided for removing parts like the bearing caps, thrust screw, and differential case halves. Safety warnings and cautions are also included throughout.
Hyster a917 (h970 hds) forklift service repair manualfjsekksmemm
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Hyster a917 (h1050 hds) forklift service repair manualfujsjefkksekmm
This document provides repair procedures for differentials. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, disassemble the differential and ring gear assembly, and disassemble the drive pinion and pinion carrier from the differential carrier. Detailed steps are provided for removing parts like the bearing caps, thrust screw, and drive pinion. Safety warnings and cautions are included throughout.
Hyster a917 (h970 hds) forklift service repair manualfujsjefjkskefksem
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Mc cormick v series cab tier 2 new generation (2005 2007) - rp03 - v80 tracto...fjsekkdmeik
This document provides information on engine parts for a V80 tractor, including part numbers, descriptions, and repair kit information. It lists individual parts like cylinders, crankshafts, gears, and rings. It also provides the repair kit numbers and specifications for rebuilding the engine, noting color coding and shim thickness variations between kits. Replacement part quantities are specified based on the number of tractors sold.
Mc cormick v series cab tier 2 new generation (2005 2007) - rp03 - v75 tracto...fjsekkdmeik
This document contains parts listings and repair instructions for engine components. It includes kits for crankshaft replacement or repair with different shim options, as well as kits for connecting rod replacement that are designated by color. It also lists components like pistons, rings, gears, and related fasteners that may need to be replaced during an engine overhaul.
More Related Content
Similar to Hyster e117 (h1050 hd ch) forklift service repair manual
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfujjdfjkwskemme
The document provides descriptions and repair procedures for a planetary gear axle. It describes the components of the axle, including the axle housing, two final drive assemblies which contain planetary gear units, differential, and brake assemblies. It then provides detailed steps for disassembling, inspecting, repairing, cleaning, and reassembling the various components of the planetary gear axle.
Hyster b214 (h22.00 xm 12ec europe) forklift service repair manualfjsekqazxkdmmem
This document provides descriptions and repair procedures for a planetary gear axle. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The document describes the components of the axle, including the differential, brakes, sun gear, planetary gears, ring gear, and hub. It then provides step-by-step instructions to disassemble the axle housing, planetary gear carrier, ring gear assembly, and wheel hub.
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualfujsjefjskekemm
The document provides descriptions and repair procedures for a planetary gear axle assembly. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio and increases torque to the drive wheels. The assembly includes an axle housing, axle shafts, sun gears, planetary gears, ring gears, and differentials. The repair section provides steps to disassemble, inspect, repair, clean, and reassemble the various components. Welding is not permitted and worn parts must be replaced. Ground metal surfaces require solvent cleaning only while other parts can be cleaned in hot alkaline solutions.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfusjfjskekmem
The document provides information about repairing a planetary gear axle. It describes the components of the axle, including the axle housing, two final drive assemblies that contain planetary gear units, differential, and service/parking brakes. The operation of the planetary gearing is explained. Repair procedures are outlined for disassembling, inspecting, cleaning, and replacing worn parts. Welding is not recommended for repair. Ground metal parts require solvent cleaning only.
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualfusjjjsekkekm
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies, a differential, and service/parking/auxiliary brake assemblies.
2) Each final drive assembly is a planetary gear unit that changes the final drive ratio to increase torque to the drive wheels. It includes components like an axle shaft, sun gear, ring gear hub, planetary pinions, and a carrier.
3) The repair process involves removing the wheels, draining fluids, disconnecting brake and drive components, and then disassembling the individual parts like the planetary carrier, ring gear hub, and wheel hub to access and replace components. Proper support and safety precautions are
Hyster b214 (h16.00 xm 12ec europe) forklift service repair manualusjfjkememe
The document provides descriptions and repair procedures for a planetary gear axle assembly. It has two final drive assemblies, each with a planetary gear unit that changes the final drive ratio. The operation section describes how the differential and sun gears rotate the axle shafts and planetary gears to turn the wheels. The repair section gives instructions for disassembling, cleaning, inspecting, and replacing worn parts before reassembly. Safety warnings are provided throughout regarding lifting heavy components and handling brake dust.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfusjejfskekemm
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies that are planetary gear units to increase torque to the drive wheels.
2) It provides an overview of the main components - axle shafts, sun gears, planetary pinions, planetary gear carriers, ring gears, and differentials. Service and parking brakes are also installed.
3) The operation section explains how the differential rotation causes the axle shafts and sun gears to rotate, turning the planetary pinions which rotate the planetary spiders and drive wheels, while the ring gear and hub do not rotate.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfjsekkdmme
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies that are planetary gear units to increase torque to the drive wheels.
2) It provides diagrams and descriptions of the key components, including the axle shafts, sun gears, planetary pinions, planetary gear carriers, ring gears, and differentials.
3) The repair process is outlined, beginning with removing the wheels and tires, then draining fluids before disassembling the various components like the planetary gear carriers, ring gears, and wheel hubs. Safety warnings are provided throughout.
Hyster d024 (s7.0 ft europe) forklift service repair manualfjjskefkskem
This document provides instructions for removing and repairing a drive axle, differential, and wet disc brakes on a service vehicle. It describes removing the drive axle by draining fluids, disconnecting lines and hoses, and removing mounting hardware. It then details disassembling the planetary gear assembly within the drive axle by removing retaining rings, gears, seals, and bearings. Finally, it outlines disassembling the wet disc brakes by removing mounting screws, pistons, springs, plates, and discs.
Hyster h007 (h170 hd) forklift service repair manualfjsjfjskeksmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how the planetary axles operate and provides instructions for identifying the exact axle model. It then provides steps for disassembling the planetary axle assembly including draining lubricant, removing brake drums, planetary spiders, pinion gears, ring gears, wheel hubs and bearings.
Hyster h007 (h190 hd) forklift service repair manualfjskekdmmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how to disassemble the planetary axle assembly, including draining lubricant, removing wheels and brake drums, and removing the planetary spider and gearing components.
Hyster h007 (h210 hd) forklift service repair manualfjskekdmmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how the planetary axles operate and provides instructions for identifying the exact axle model. It then provides steps for disassembling the planetary axle assembly including draining lubricant, removing brake drums, planetary spiders, pinion gears, ring gears, wheel hubs and bearings.
Hyster h007 (h280 hd) forklift service repair manualfjsekqazxkdmmem
This document provides descriptions and repair procedures for planetary gear axles. It describes the components of the planetary axle assembly including the carrier/differential assembly, hypoid gearing, planetary spur gearing in the wheel hubs. It provides diagrams of the wheel end cross sections and identifies components. The document describes how to disassemble the planetary axle assembly, including draining lubricant, removing wheels and brake drums, and removing the planetary spider and gearing components.
Hyster h007 (h230 hd) forklift service repair manualfjsjfjskeksmem
The document provides descriptions and repair procedures for a planetary gear axle. It describes the components of the axle including the hypoid gearing, planetary spur gearing, and wheel hub assemblies. The procedures describe how to disassemble the wheel ends, planetary spider and gearing assembly, dry brakes, and other components for inspection or replacement of parts. Detailed diagrams are provided to identify the components.
Hyster f117 (h50.00 xm 16ch europe) forklift service repair manualfsefkksefmme
This document provides repair procedures for a differential assembly. It describes removing the differential carrier from the axle housing and then disassembling the differential carrier. The procedures cover removing the differential and ring gear assembly, drive pinion and pinion carrier from the differential carrier housing. Detailed steps are provided to properly support the vehicle, drain oil, disconnect driveline components, and remove fasteners holding parts together. Safety warnings are included to prevent injury when using jack stands and mallets during the repair process.
Hyster f117 (h52.00 xm 16ch europe) forklift service repair manualfsefkksefmme
This document provides repair procedures for a differential assembly. It describes removing the differential carrier from the axle housing and then disassembling the differential carrier. The procedures cover removing the differential and ring gear assembly, drive pinion and pinion carrier from the differential carrier housing. Detailed steps are provided to disassemble the differential and ring gear assembly. Safety warnings and cautions are included throughout regarding properly supporting the vehicle, using appropriate tools to avoid damage, and marking parts for reassembly.
Hyster a917 (h900 hds) forklift service repair manualfujsjfjksekem
This document provides repair procedures for differentials. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures explain how to remove the differential carrier from the axle housing, disassemble the differential and ring gear assembly, and remove the drive pinion and pinion carrier from the differential carrier. Detailed steps are provided for removing parts like the bearing caps, thrust screw, and differential case halves. Safety warnings and cautions are also included throughout.
Hyster a917 (h970 hds) forklift service repair manualfjsekksmemm
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Hyster a917 (h1050 hds) forklift service repair manualfujsjefkksekmm
This document provides repair procedures for differentials. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, disassemble the differential and ring gear assembly, and disassemble the drive pinion and pinion carrier from the differential carrier. Detailed steps are provided for removing parts like the bearing caps, thrust screw, and drive pinion. Safety warnings and cautions are included throughout.
Hyster a917 (h970 hds) forklift service repair manualfujsjefjkskefksem
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Safety precautions are provided and components are labeled in diagrams.
Similar to Hyster e117 (h1050 hd ch) forklift service repair manual (20)
Mc cormick v series cab tier 2 new generation (2005 2007) - rp03 - v80 tracto...fjsekkdmeik
This document provides information on engine parts for a V80 tractor, including part numbers, descriptions, and repair kit information. It lists individual parts like cylinders, crankshafts, gears, and rings. It also provides the repair kit numbers and specifications for rebuilding the engine, noting color coding and shim thickness variations between kits. Replacement part quantities are specified based on the number of tractors sold.
Mc cormick v series cab tier 2 new generation (2005 2007) - rp03 - v75 tracto...fjsekkdmeik
This document contains parts listings and repair instructions for engine components. It includes kits for crankshaft replacement or repair with different shim options, as well as kits for connecting rod replacement that are designated by color. It also lists components like pistons, rings, gears, and related fasteners that may need to be replaced during an engine overhaul.
Mc cormick v series cab tier 2 (2003 2005) - rp02 - v85 tractor service repai...fjsekkdmeik
This document provides parts information for an engine, listing component part numbers, descriptions, and other technical details. It includes listings for various engine kits, cylinders, bearings, valves, pistons, shafts, gears, and other internal engine parts. Notes provide information on serial numbers ranges for parts and indicators that some items are not serviced and must be replaced as assemblies.
Mc cormick v series cab tier 2 (2003 2005) - rp02 - v75 tractor service repai...fjsekkdmeik
This document contains parts lists and component information for various engine systems. It includes lists of parts with identification numbers, descriptions, and kit or replacement part numbers. Notes provide additional details like serial number ranges and component functions.
Mc cormick ttx tier 3 (2007 ) - xtx4 - 230 tractor service repair manualfjsekkdmeik
This document provides a list of components for an engine assembly. It includes over 70 line items with descriptions of parts like screws, bolts, pins, plates, manifolds, and more. Each item includes information on the part number, quantity, and any references. The document also indicates this is for an Iveco 154kw engine that meets Tier 3 emissions standards from 2007 onwards for the XTX4 model 230.
Mc cormick ttx tier 3 (2007 ) - xtx4 - 210 tractor service repair manualfjsekkdmeik
This document contains parts lists and diagrams for components of an engine assembly. It lists over 70 individual part numbers, descriptions and quantities. Reference numbers link the components to assembly diagrams on other pages. The parts include items like screws, pins, bearings, manifolds, pistons, gears and more.
Mc cormick ttx tier 3 (2007 ) - xtx4 - 190 tractor service repair manualfjsekkdmeik
This document contains parts listings and diagrams for components of an engine assembly. It lists part numbers, descriptions, quantities and references other assemblies. Notes provide information on markets, serial numbers and page references for some components. The high level information is engine replacement parts and diagrams for assemblies such as the cylinder head, camshaft and crankshaft.
Mc cormick t series tier 3 (2007 2010) - cp02 - t80 f-m tractor service repai...fjsekkdmeik
This document provides parts information for an engine replacement. It includes lists of components with part numbers, references, and other technical specifications. The parts are for a Tier 3 McCormick tractor from 2007-2010 and include items like cylinders, pistons, sensors, hoses, and other engine parts.
Mc cormick t series tier 3 (2007 2010) - cp02 - t 105 f-m-c tractor service r...fjsekkdmeik
This document provides parts information for various engine components. It includes part numbers, descriptions, replacement part numbers, and other technical specifications. The parts are for Perkins engines that meet Tier 3 emissions standards from 2007-2010 for agricultural tractors.
Mc cormick t series tier 3 (2007 2010) - cp02 - t 100 f-m-c tractor service r...fjsekkdmeik
This document contains parts lists and component information for various engine systems. It includes items like cylinder heads, pistons, pumps, sensors and their associated reference numbers. Installation and replacement instructions are provided along with part numbers and serial number ranges for applicability.
Mc cormick t series restyling (2011 ) - cp03 - t100 f-m-c tractor service re...fjsekkdmeik
This document provides parts information for engines and components. It includes lists of parts with identification numbers, quantities, and notes on replacement options and part numbers. Key information includes identification of engine models and part numbers for components like pistons, rods, pumps, sensors and more.
Mc cormick t series restyling (2011 ) - cp03 - t 105 f-m-c tractor service r...fjsekkdmeik
This document provides parts information for various engine components. It includes lists of parts with identification numbers, quantities, and other technical specifications. The parts are grouped by component type and include items like pistons, rods, pumps, sensors and more. Replacement part numbers are provided where needed along with other installation or ordering notes.
Mc cormick t series restyling (2011 ) - cp03 - t 90 f-m-c tractor service re...fjsekkdmeik
This document contains parts lists and component information for engines and engine systems for tractors. It includes lists of parts with part numbers, quantities and references to replacement kits or part numbers. Notes provide information on component applications and whether items are serviced or require replacement.
Mc cormick mtx tier3 restyling (2009 ) - rpd1 - 150 tractor service repair m...fjsekkdmeik
This document provides a list of components for an engine assembly. It includes the reference number, description, and quantity of each component. Additional information includes the market applicability and page references for some components.
Mc cormick mtx tier3 restyling (2009 ) - rpd1 - 135 tractor service repair m...fjsekkdmeik
This document provides a list of components for an engine assembly including identification numbers, descriptions, and quantities. It includes items like screws, gaskets, dowel pins, pistons, rods, bearings, pumps, magnets and other engine parts. Notes provide information on markets, serial numbers, and references to other pages for additional details. The purpose is to specify all items needed for the engine assembly.
This document provides a list of parts for Massey Ferguson 8450/8460 Tier 2 tractors. It includes 52 numbered items with descriptions of engine parts like the cylinder block, timing gear housing, alternator, and starter. The parts are identified by part number, quantity, and a brief description. Footnotes provide additional details for some items.
This document provides a list of parts for Massey Ferguson 8450/8460 Tier 2 tractors. It includes 52 numbered items with descriptions of engine parts like the cylinder block, timing gear housing, alternator, and starter. The parts are identified by part number, quantity, and a brief description. Footnotes provide additional details for some items.
Massey ferguson mf8260 tractor parts catalogue manualfjsekkdmeik
This document provides a list of parts and their descriptions for the engine and related components of a Massey Ferguson 8260 tractor. It includes 21 items related to the valve mechanism and camshaft, including the rocker shaft, rockers, tappets, camshaft and related hardware. The document also lists parts for the cylinder block, timing gear housing, flywheel housing, crankshaft, pistons, connecting rods and other engine components.
Kubota b5100 d p tractor parts catalogue manualfjsekkdmeik
The document provides instructions for parts books, including definitions of column headings in parts number pages. It lists country codes used in parts books in different countries. It then provides an example page from a parts book, listing part numbers, descriptions, quantities and other information for various components of an engine and other systems.
Kubota b4200 d tractor parts catalogue manualfjsekkdmeik
The document provides instructions for using a parts book for a B4200D tractor. It begins with definitions of the column headings used on parts number pages, including the part number, description, quantity, and compatibility codes. It then provides a sample parts listing page with over 200 part numbers, descriptions, and other details. It ends with notes about country codes that may be included to indicate part number differences between countries.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. 1400 SRM 1171 Operation
General
This section has a description and the repair procedures for the planetary gear axle.
Description
The planetary gear axle has an axle housing and two
final drive assemblies. See Figure 1 and Figure 2.
Each final drive assembly is a planetary gear unit.
The planetary gear assembly changes the final drive
ratio, which increases the torque to the drive wheels.
Each unit has a drive axle, sun gear, ring gear hub,
and ring gear. There are also three planetary pin-
ions, a planetary spider, and a housing. The differ-
ential is also installed in the axle housing. The ser-
vice brake is also installed on the drive axle. See the
section Service Brake for your lift truck, for repair
instructions of the brakes.
Operation
The rotation of the differential causes the axle shafts and the sun gears to rotate. The sun gears then cause
the planetary pinions to rotate. Rotation of the pinions causes the planetary spiders to rotate the hubs and the
drive wheels. The ring gear and the ring gear hub do not rotate.
1
6. 1400 SRM 1171 Planetary Gear Axle Repair
Planetary Gear Axle Repair
REMOVE
Drive Wheels and Tires
NOTE: The final drive assemblies can be removed
with the drive axle installed in the lift truck. If the
drive axle must be removed, do the following steps.
If the drive axle will not be removed, do only the re-
quired steps.
1. Place lift truck on solid, level surface.
2. Put blocks on each side (front and back) of the
steer tires to prevent movement of the lift truck.
See Figure 3, Figure 4, and Figure 5.
3. Put mast in a vertical position.
4. Put a block under each outer mast channel.
5. Tilt mast fully forward until drive tires are raised
from the surface.
CAUTION
Do not place blocks under fuel and hydraulic
hoses or fuel and hydraulic tank. Damage to
the lift truck may occur.
6. Put additional blocks under frame behind the
drive tires.
WARNING
Completely remove air pressure from tire be-
fore it is removed from lift truck. Because dual
wheels are installed, remove air pressure from
both tires. Air pressure in tires can cause tire
and wheel parts to explode, causing serious in-
jury or death.
7. Remove air from tire.
8. Remove valve core to verify that all air is out of
inner tube.
9. Push a wire through valve stem to verify the stem
does not have a restriction.
10. Remove wheel nuts and clamps.
WARNING
The tires and wheels can weigh approximately
875 kg (1929 lb). Verify the lifting device has
the rated capacity to lift the tires and wheels
or personal injury may occur.
11. Remove wheel and tire from lift truck.
1. STEER AXLE/STEER TIRES 2. DRIVE AXLE/DRIVE TIRES
Figure 3. Put Lift Truck on Blocks (A917)
5
7. Planetary Gear Axle Repair 1400 SRM 1171
1. STEER AXLE/STEER TIRES 2. DRIVE AXLE/DRIVE TIRES
Figure 4. Put the Lift Truck on Blocks (B222)
1. STEER AXLE/STEER TIRES
2. DRIVE AXLE/DRIVE TIRES
Figure 5. Put the Lift Truck on Blocks (E117
and F117)
DISASSEMBLE
Drive Axle
1. Apply brakes ten to twenty times until accumu-
lated hydraulic brake pressure is released.
2. Drain oil from the end of axle housing.
3. Rotate hub assembly until oil drain plug in plan-
etary gear carrier is at the bottom.
4. Remove oil drain plug and drain oil.
5. Drain cooling oil from service brakes.
WARNING
Brake linings can contain dangerous fibers.
Breathing dust from these linings is a cancer
or lung disease hazard. Do not create dust! Do
not clean brake parts with compressed air or
by brushing. Use vacuum equipment approved
for brake dust or follow the cleaning proce-
dure in this section. When the brake drums
are removed, do not create dust.
Do not sand, grind, chisel, hammer, or change
linings in any way that will create dust. Any
changes to linings must be done in a restricted
area with special ventilation. Protective cloth-
ing and a respirator must be used.
NOTE: Under normal conditions, the disc assembly
(fixed and rotating discs) of the oil-cooled brakes is
replaced when the drive axle is disassembled.
6. Disconnect service brake lines.
7. Disconnect brake lines for parking brake at the
differential.
8. Disconnect cooling oil lines for oil-cooled brakes.
9. Put caps on all hydraulic lines, ports, and fit-
tings.
10. Disconnect drive shaft at differential.
11. Put forks of another lift truck under the axle for
support.
6
8. 1400 SRM 1171 Planetary Gear Axle Repair
12. Remove bolts and nuts that hold the axle to the
frame.
WARNING
Verify the lifting device has the rated capacity
of 4500 kg (9921 lb) when moving the drive axle.
13. Remove drive axle from lift truck frame.
WARNING
Cleaning solvents are flammable and toxic and
can cause skin irritation. When using clean-
ing solvents, always follow the solvent manu-
facturer’s recommended safety precautions.
WARNING
Compressed air can move particles so that they
cause injury to the user or to other personnel.
Verify that the path of the compressed air is
away from all personnel. Wear protective gog-
gles or a face shield to prevent injury to the
eyes.
14. Clean all parts in solvent and dry with com-
pressed air.
Planetary Gear Carrier
1. Align marks on planetary gear carrier and wheel
hub for correct alignment when reassembling the
unit. See Figure 6.
A. RIM MOUNTED
1. ALIGNMENT MARKS
Figure 6. Alignment Marks
2. Remove cover from planetary gear carrier. See
Figure 7.
1. HUB
2. COVER
3. PLANETARY GEAR CARRIER
Figure 7. Planetary Gear Carrier Cover
3. Remove planetary gear carrier capscrews.
NOTE: Do not remove planetary gear carrier at this
time.
4. Insert a pry bar into assembly notches and sep-
arate planetary gear carrier from wheel hub as-
sembly. See Figure 8.
Figure 8. Planetary Gear Carrier Separation
7
9. Planetary Gear Axle Repair 1400 SRM 1171
WARNING
Use caution when using lifting devices. When
using a lifting strap, inspect strap for damage
before using. Do not use a lifting strap to shock
load or drop load a component. Serious per-
sonal injury and damage to components may
occur.
Verify the lifting device has the rated capacity
of 150 kg (331 lb) when moving the planetary
gear carrier.
5. Use a lifting device to remove planetary gear car-
rier from wheel hub assembly. See Figure 9.
Figure 9. Planetary Gear Carrier Removal
WARNING
Observe all WARNINGS and CAUTIONS pro-
vided by press manufacturer concerning press
operation to avoid serious injury and possible
damage to components during assembly and
installation procedures.
NOTE: If a press is not available, use a brass drift
and mallet to remove pinion shafts.
6. Place the planetary gear carrier assembly in a
press with flange side DOWN. Support the spi-
der assembly as required.
NOTE: Use a soft material in bottom of the catch con-
tainer to prevent damage to the pinion shafts.
7. Place a container under the press to catch the
planetary pinion shafts as they are pressed out of
the planetary gear carrier and planetary pinion
gears.
8. Press each pinion shaft out of planetary gear car-
rier and planetary gear. See Figure 10.
1. SPIDER
2. PINION SHAFT
3. OUTER THRUST WASHER
4. PLANETARY GEAR
5. SMALL BORE INNER THRUST WASHER
Figure 10. Pinion Shaft
9. Remove planetary gears and thrust washers
from planetary gear carrier.
Ring Gear, Ring Gear Hub, and Wheel Hub
1. Remove snap ring from end of axle shaft. See
Figure 11.
2. Remove sun gear. See Figure 11.
3. Remove sun gear thrust washer assembly. See
Figure 12.
8
10. Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
11. 1400 SRM 1171 Planetary Gear Axle Repair
1. SUN GEAR
2. SNAP RING
3. AXLE SHAFT
4. RING GEAR
Figure 11. Sun Gear
1. WHEEL BEARING ADJUSTING NUT
2. WHEEL BEARING ADJUSTING LOCK NUT
3. CAPSCREW
4. AXLE SHAFT
5. THRUST WASHER
Figure 12. Thrust Washer Assembly
4. Remove capscrews from wheel bearing adjusting
lock nut. See Figure 2 and Figure 12.
5. Remove wheel bearing adjusting lock nut and
wheel bearing adjusting nut. See Figure 2 and
Figure 12.
WARNING
Support the wheel hub before you remove
ring gear and ring gear hub assembly. Do not
remove ring gear and ring gear hub assembly
without supporting the wheel hub. Serious
injury and damage to components may occur.
See Figure 13.
NOTE: To avoid dropping and possibly damaging
the outer wheel bearing cone, verify the outer wheel
bearing cone remains in place as you remove the
ring gear hub.
NOTE: If the ring gear hub cannot be removed by
hand, install capscrews into the puller screw holes
in the ring hub flange. Tighten each capscrew the
same amount to separate ring gear hub from spindle
and wheel hub.
6. Remove ring gear hub by pulling it straight out
of wheel hub and off of spindle.
Figure 13. Ring Gear Hub
7. Remove retainer plate capscrews to remove ring
gear from ring gear hub. See Figure 14.
9
12. Planetary Gear Axle Repair 1400 SRM 1171
1. RING GEAR HUB
2. OUTER WHEEL BEARING
3. RETAINER PLATE
4. RING GEAR
Figure 14. Retainer Plate
8. Remove outer wheel bearing from ring gear hub.
NOTE: The ring gear hub assembly includes the hub
and ring sleeve insert. You cannot service these com-
ponents separately.
9. Use a hoist or similar device to lift the wheel hub
and drum slightly to relieve the hub weight and
drum-to-brake shoe drag. See Figure 15.
10. Remove wheel hub assembly from wheel hub
spindle.
Hub Oil Seal and Bearings
1. Position wheel hub with brake end UP to remove
hub oil seal and bearings.
2. Remove rotor mounting capscrews and washers.
3. Remove the rotor.
CAUTION
Do not scratch hub seal bore surface.
4. Remove bearing cups with a suitable puller.
5. Remove bearing cone with a suitable puller.
6. Remove wheel hub oil seal.
Figure 15. Wheel Hub and Drum
Axle Shaft
1. Remove axle shaft from spindle bore and hous-
ing.
2. Disassemble oil-cooled brakes as described in the
section Service Brake for your lift truck.
Spindle
NOTE: The spindle and brake cover are assembled to
the axle housing with the same capscrews.
1. Remove two of the capscrews (opposite each
other) that fasten the spindle to the axle hous-
ing. Replace with two studs, which are long
enough to support the spindle. See Figure 16.
10
13. 1400 SRM 1171 Planetary Gear Axle Repair
1. STUD
Figure 16. Brake Housing Studs
2. Remove the remaining capscrews.
3. Hold the spindle against the axle housing.
WARNING
Verify the lifting device has the rated capacity
to lift the spindle.
4. Use a lifting device to remove the spindle. See
Figure 17.
1. LIFTING DEVICE 2. SPINDLE
Figure 17. Spindle
REPAIR
Repairing or Replacing Parts
WARNING
Do not repair axle housings by bending or
straightening. Repair of axle housings by
bending or straightening can cause poor per-
formance and possible unsafe operation of the
axle. This can cause serious personal injury.
NOTE: Threads must be without damage and clean,
so accurate adjustment and correct torque values can
be applied to fasteners and parts.
Replace worn or damaged parts of an axle assembly.
The following are some examples for possible repair
and replacement:
• Replace any fastener if corners of wrench flats are
worn.
• Replace washers if damaged.
• Replace gaskets, oil seals, and grease seals.
• Clean parts and apply silicon gasket material,
where required.
• Remove nicks, marks, and burrs from parts having
machined or ground surfaces. Use a fine file, India
stone, emery cloth, or crocus cloth.
• Clean and repair threads of fasteners and holes.
Use a die or tap of correct size or a fine file.
Welding
Do not repair the drive axle assemblies by welding.
Welding can detract from the structural integrity of a
component, particularly to heat-treated parts where
the benefit of heat treatment can be nullified by weld-
ing.
11
14. Planetary Gear Axle Repair 1400 SRM 1171
CLEAN
Ground or Polished Parts
WARNING
To prevent serious eye injury, always wear safe
eye protection when performing vehicle main-
tenance or service.
WARNING
Solvent cleaners are flammable, poisonous,
and can cause burns. Examples of solvent
cleaners are carbon tetrachloride, emul-
sion-type cleaners, and petroleum-based
cleaners. To avoid serious personal injury
when using solvent cleaners, carefully follow
the manufacturer’s product instructions and
these procedures.
• Wear safe eye protection.
• Wear clothing that protects your skin.
• Work in a well-ventilated area.
• Do not use gasoline or solvents that contain
gasoline. Gasoline can explode.
• Use hot solution tanks or alkaline solutions
correctly. Follow the manufacturer’s instruc-
tions carefully.
CAUTION
• Use only solvent cleaners to clean ground
or polished metal parts. Hot solution tanks
or water and alkaline solutions will damage
these parts. Isopropyl alcohol, kerosene, or
diesel fuel can be used for this purpose.
• If required, use a sharp knife to remove gas-
ket material from parts. Be careful not to
damage the ground or polished surfaces.
1. Use a cleaning solvent, kerosene, or diesel fuel
to clean ground or polished parts or surfaces.
NEVER USE GASOLINE.
2. Remove gasket material from parts. Use caution
not to damage ground surfaces. Apply grease to
prevent corrosion.
3. DO NOT clean ground or polished parts in a hot
solution tank, water, steam, or alkaline solution.
Parts With Rough Finishes
1. Use a cleaning solvent or a hot solution tank with
a weak alkaline solution to clean parts with a
rough finish.
2. Leave parts in the hot solution tank until they
are completely cleaned and heated. When the
parts are clean, remove them from the tank.
3. Wash the parts with water until alkaline solution
is completely removed.
Axle Assemblies
NOTE: A complete axle assembly can be steam
cleaned on the outside to remove dirt.
NOTE: Before the axle is steam cleaned, close or put
a cover over all the openings in the axle assembly.
Examples of openings are the breathers or vents in
air chambers.
Drying Cleaned Parts
CAUTION
Dry bearings with clean paper or rags. Do not
use compressed air, which can cause abrasive
particles to contaminate the bearings. Damage
to components and reduced lining life can re-
sult.
Immediately after cleaning, use clean paper, rags, or
compressed air to dry parts.
PREVENTING CORROSION
NOTE: Parts must be clean and dry before lubricat-
ing them.
1. If assembling the parts immediately after clean-
ing them, lubricate the clean, dry parts with
grease to prevent corrosion.
2. If storing the parts after cleaning them, apply
a corrosion-preventive material to all machined
surfaces. Store the parts in a special paper or
other material that prevents corrosion.
PARTS INSPECTION
It is very important to inspect all parts carefully and
completely before axle or carrier is assembled. Check
all parts for wear and replace damaged parts. Re-
placement of damaged or worn parts will prevent
breakdown of assembly later.
12
15. 1400 SRM 1171 Planetary Gear Axle Repair
ASSEMBLE
Spindle
1. Install two studs opposite each other on the axle
housing flange. Verify the studs are long enough
to support the spindle.
2. Apply a bead of silicone gasket material on the
mounting surface of the axle housing flange. The
bead must go around each capscrew hole. See
Figure 18.
1. AXLE FLANGE
2. SILICONE BEAD
Figure 18. Axle Flange
WARNING
Verify the lifting device has the rated capacity
to lift the spindle.
3. Use a lifting device to install the spindle on the
guide studs. Verify the spindle cannot fall before
removing the lifting device. See Figure 18.
4. Tighten the capscrews to the torque specified.
See Table 2.
Axle Shaft
1. Replace oil-cooled brake as described in the sec-
tion Service Brake for your lift truck.
2. Install axle shaft through the spindle bore and
housing until it engages the differential side
gear. The shaft end with the snap ring groove
must extend beyond the outer end of the spindle.
Hub Oil Seal and Bearings
1. Position wheel hub with brake end UP to install
hub oil seal and bearings.
2. Position new wheel hub oil seal so that the spring
lip of the seal faces the wheel bearing. Use a suit-
able seal driver to drive seal into same location as
original wheel hub oil seal.
CAUTION
Use caution not to nick the seal oil wear sleeve
end when installing the oil seal wear sleeve. A
nicked oil seal wear sleeve end can damage the
seal lip when installing the wheel hub. Lubri-
cant loss and damage to components may oc-
cur.
3. Carefully install a new oil seal wear sleeve on the
spindle.
4. Lubricate new seals as follows:
• Lubricate the oil seal lips of conventional seals.
• Lubricate the inside diameter of unitized seals.
• Lubricate contact surfaces of the metal rings on
face seals. Do not apply lubricant to any other
part of the face seal.
5. Apply a thin coat of lubricant to the oil seal jour-
nal surface of the spindle.
6. Apply lubricant to the inner bearing cone rollers.
7. Install the inner bearing cone into wheel hub.
NOTE: If the hub bearing cups need to be replaced,
install the new cups with a suitable driver.
8. Install bearing cups into wheel hub.
NOTE: If slinger fits loosely between wheel hub and
drum, apply a bead of liquid gasket material to pre-
vent rattling.
9. Install brake rotor or drum and oil slinger.
10. Install drum or rotor mounting capscrews and
washers.
13
16. Planetary Gear Axle Repair 1400 SRM 1171
Ring Gear, Ring Gear Hub, and Wheel Hub
WARNING
Use caution when using lifting devices. When
using a lifting strap, inspect strap for damage
before using. Do not use a lifting strap to shock
load or drop load a component. Serious per-
sonal injury and damage to components may
occur.
1. Using a hoist or similar device, carefully lift
the wheel hub assembly over wheel hub spin-
dle. Keep the wheel hub assembly aligned with
wheel hub spindle to avoid oil seal damage. See
Figure 15.
2. Install outer wheel bearing cone on the ring gear
hub journal squarely against hub shoulder. Ap-
ply the same lubricant used in the wheel ends to
the rollers. Slip fit outer wheel bearing cone over
ring gear hub journal. See Figure 14.
3. Install retainer plate with bolts.
4. Install ring gear assembly, which includes outer
bearing cone, on wheel hub spindle.
5. Install wheel bearing adjusting lock nut and
wheel bearing nut on spindle. See Figure 2 and
Figure 12.
Wheel Bearing Preload
Adjust
1. Tighten the wheel bearing adjusting nut to the
initial seating torque listed in Table 1.
2. Rotate the wheel hub, a minimum of two full rev-
olutions in both directions.
3. Using a suitable bar and not to exceed 5 kg (10 lb)
of force, tap the ring gear hub to assist in seating
the wheel hub. For location of tapping of suitable
bar, see Figure 19.
Figure 19. Location of tapping the ring gear
hub
4. Repeat tightening the wheel bearing adjusting
nut to the initial seating torque listed in Table 1.
5. Rotate the wheel hub, a minimum of two full rev-
olutions in both directions.
6. Tap the ring gear hub to assist in seating the
wheel hub.
7. Loosen the adjusting nut 1
/8 to 1
/4 turn.
8. Tighten the adjusting nut to the final adjustment
nut torque listed in Table 1.
9. Rotate the wheel hub, a minimum of two full rev-
olutions in both directions.
10. Tap the ring gear hub to assist in seating the
wheel hub.
11. Tighten the adjusting nut to the final adjustment
nut torque listed in Table 1.
12. Repeat Step 9 thru Step 11 until the adjusting
nut can no longer be turned.
Table 1. Wheel Bearing Adjustment Torque
Adjusting Nut Torque
Axle Models
Initial Seating Final Adjustment
PRC-5324 to 7314 813 N•m (600 lbf ft) 678 N•m (500 lbf ft)
PRC-7534 949 N•m (700 lbf ft) 746 N•m (550 lbf ft)
14