- The document provides repair instructions for various components on a forklift truck frame, including covers, panels, and plates, load wheels, and general safety warnings.
- Key components that can be repaired include the front frame panels, operator compartment cover, drive unit compartment door, various pads, and caster wheel cover. Instructions are provided for removing and installing these parts.
- Load wheel removal instructions include removing the nut, washers, axle bolt, and then pressing or tapping the bearings and axle sleeves from the load wheels using a soft punch and hammer to avoid damage.
Hyster b108 (e40 b [americas]) forklift service repair manualjfjskeksemmmd
This document provides information on servicing and repairing gear pumps. It describes the components and operation of single-stage and tandem gear pumps. The main steps for repair are removal, disassembly, cleaning, inspection, and reassembly. Key points include inspecting gears, housings, thrust plates and seals for wear or damage and replacing any worn parts. Proper cleaning and ensuring no dirt enters during reassembly are important to prevent failures.
Hyster g007 (h210 hd) forklift service repair manualfujdwjjsekkemme
This document provides instructions for servicing the hydraulic tank on Hyster lift trucks. It describes how to remove the tank by disconnecting hoses and electrical connections, draining the fluid, and removing mounting hardware. It also provides cleaning and repair instructions for the tank, including preparing it for welding. The installation instructions describe reconnecting all hoses and mounting the tank back onto the lift truck frame. Safety precautions are provided throughout to warn of hazards like sparks near flammable vapors.
Hyster p005 (h110) forklift service repair manualjfjskeksemmmd
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Disassembly steps are provided to take apart the differential case halves. Specifications and troubleshooting information are also referenced.
Hyster g007 (h12.00 xm europe) forklift service repair manualfdujsjefjskekmsme
The document provides instructions for repairing the counterweight, fenders, hood, hydraulic tank, and other parts of a service vehicle. It describes removing and installing the heavy counterweight using lifting devices. Procedures are given for removing and replacing side counterweights, repairing leaks in the hydraulic tank through cleaning and welding, and removing the hood assembly or pivoting it out of the way for access. Safety warnings are included throughout regarding the heavy components, welding near electronic modules, and cleaning tank interiors.
Hyster g007 (h250 hd) forklift service repair manualusfjjsjekkemm
This document provides instructions for removing and installing the hydraulic tank on Hyster lift trucks. Key steps include draining the hydraulic oil from the tank, disconnecting hoses and electrical connections, and removing mounting hardware. The tank should be cleaned and inspected for leaks before reinstallation. Proper safety precautions are outlined, including disconnecting battery cables and using approved cleaning solutions and welding practices.
Hyster e019 (h10.00 xm 12ec, europe) forklift service repair manualujdfjjjdfkkskemm
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and other parts. The counterweight is heavy and must be lifted carefully using lifting devices. Fenders are also heavy and require lifting safely. Instructions are provided for removing, inspecting, and reinstalling these parts, as well as other components like the hood and hydraulic tank. Welding precautions are noted to avoid damaging electronic modules.
Hyster h006 (h135 ft) forklift service repair manualfusjefjsekksemm
This document provides instructions for servicing various components of a lift truck, including:
1. Removing and installing side covers, the seat, dash, kick panel, and seal plate.
2. Removing and installing the hood support and door assembly, which requires lifting equipment due to the assembly's weight.
3. Removing and installing the LPG tank and bracket assembly, with warnings about avoiding sparks near the LPG system.
Hyster h006 (h135 ft) forklift service repair manualfjsjekkdmmemm
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, seats, dashes, and hoods.
2) Inspecting operator restraint systems like seat belts.
3) Removing and installing steering columns, dashes, kick panels, and seal plates.
4) Removing and installing hood supports and door assemblies.
The document contains detailed step-by-step instructions and diagrams to guide maintenance and repairs. Safety warnings are also provided about putting the lift truck on blocks during work.
Hyster b108 (e40 b [americas]) forklift service repair manualjfjskeksemmmd
This document provides information on servicing and repairing gear pumps. It describes the components and operation of single-stage and tandem gear pumps. The main steps for repair are removal, disassembly, cleaning, inspection, and reassembly. Key points include inspecting gears, housings, thrust plates and seals for wear or damage and replacing any worn parts. Proper cleaning and ensuring no dirt enters during reassembly are important to prevent failures.
Hyster g007 (h210 hd) forklift service repair manualfujdwjjsekkemme
This document provides instructions for servicing the hydraulic tank on Hyster lift trucks. It describes how to remove the tank by disconnecting hoses and electrical connections, draining the fluid, and removing mounting hardware. It also provides cleaning and repair instructions for the tank, including preparing it for welding. The installation instructions describe reconnecting all hoses and mounting the tank back onto the lift truck frame. Safety precautions are provided throughout to warn of hazards like sparks near flammable vapors.
Hyster p005 (h110) forklift service repair manualjfjskeksemmmd
This document provides repair procedures for differentials used in lift trucks. It describes the components of a typical differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures describe how to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. Disassembly steps are provided to take apart the differential case halves. Specifications and troubleshooting information are also referenced.
Hyster g007 (h12.00 xm europe) forklift service repair manualfdujsjefjskekmsme
The document provides instructions for repairing the counterweight, fenders, hood, hydraulic tank, and other parts of a service vehicle. It describes removing and installing the heavy counterweight using lifting devices. Procedures are given for removing and replacing side counterweights, repairing leaks in the hydraulic tank through cleaning and welding, and removing the hood assembly or pivoting it out of the way for access. Safety warnings are included throughout regarding the heavy components, welding near electronic modules, and cleaning tank interiors.
Hyster g007 (h250 hd) forklift service repair manualusfjjsjekkemm
This document provides instructions for removing and installing the hydraulic tank on Hyster lift trucks. Key steps include draining the hydraulic oil from the tank, disconnecting hoses and electrical connections, and removing mounting hardware. The tank should be cleaned and inspected for leaks before reinstallation. Proper safety precautions are outlined, including disconnecting battery cables and using approved cleaning solutions and welding practices.
Hyster e019 (h10.00 xm 12ec, europe) forklift service repair manualujdfjjjdfkkskemm
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and other parts. The counterweight is heavy and must be lifted carefully using lifting devices. Fenders are also heavy and require lifting safely. Instructions are provided for removing, inspecting, and reinstalling these parts, as well as other components like the hood and hydraulic tank. Welding precautions are noted to avoid damaging electronic modules.
Hyster h006 (h135 ft) forklift service repair manualfusjefjsekksemm
This document provides instructions for servicing various components of a lift truck, including:
1. Removing and installing side covers, the seat, dash, kick panel, and seal plate.
2. Removing and installing the hood support and door assembly, which requires lifting equipment due to the assembly's weight.
3. Removing and installing the LPG tank and bracket assembly, with warnings about avoiding sparks near the LPG system.
Hyster h006 (h135 ft) forklift service repair manualfjsjekkdmmemm
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, seats, dashes, and hoods.
2) Inspecting operator restraint systems like seat belts.
3) Removing and installing steering columns, dashes, kick panels, and seal plates.
4) Removing and installing hood supports and door assemblies.
The document contains detailed step-by-step instructions and diagrams to guide maintenance and repairs. Safety warnings are also provided about putting the lift truck on blocks during work.
Hyster h006 (h155 ft) forklift service repair manualfujsjfjkskekmm
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, seats, dashes, and hoods.
2) Inspecting operator restraint systems like seat belts.
3) Removing and installing frames, counterweights, engines, and fuel tanks.
4) Proper blocking and stability procedures when components that affect the vehicle's center of gravity are removed.
Hyster h006 (h155 ft) forklift service repair manualfujdfjjskkkemw
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, the seat, dash, kick panel, and seal plate.
2) Removing and installing the hood support and door assembly, including disconnecting related components.
3) Removing and installing the hood door assembly on each side of the lift truck.
4) Instructions are provided for each component with detailed steps and diagrams to guide the process. Safety warnings are included for working with certain systems like the LPG tank.
Hyster h006 (h135 ft) forklift service repair manualfujfjjjskekemm
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, the seat, dash, kick panel, and seal plate.
2) Removing and installing the hood support and door assembly, including disconnecting related components.
3) Removing and installing the hood door assembly on each side of the lift truck.
4) Instructions for the LPG tank and bracket assembly removal are provided at the end. Safety warnings are given regarding the flammable nature of LPG.
Hyster j006 (h6.0 ft europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing and repairing various components of a lift truck, including:
- Side covers, floor plates, seats, dashes, and hoods. Removal and installation steps are provided.
- Counterweights, mufflers, overhead guards, engines, exhaust systems, and LPG fuel tanks. Procedures for checks, repairs, and safety label installation are included.
- Frames, fuel tanks, hydraulic tanks, and counterweight mounts. Component descriptions and identification are given.
- Operator restraint systems including seat belts and hip restraints. Inspection and functionality checks are outlined.
- Hood support assemblies, hood doors, pre-cleaners, and related components
Hyster j006 (h7.0 ft europe) forklift service repair manualjfksekmmdme
The document provides instructions for servicing and repairing various components of a lift truck, including:
- Removing and installing side covers, floor plates, seats, dashes, and hood assemblies.
- Inspecting and servicing the operator restraint system including seat belts.
- Removing and installing seal plates, steering columns, and hood support assemblies.
- Guidelines for putting the lift truck on blocks for maintenance and warnings about stability.
- Diagrams illustrating the locations and attachments of different parts.
Hyster j006 (h7.0 ft europe) forklift service repair manualfjjskekdmmem
This document provides instructions for servicing and repairing various components of a lift truck, including:
- Side covers, floor plates, seats, dashes, and hoods. Removal and installation steps are provided.
- Counterweights, mufflers, overhead guards, engines, exhaust systems, and LPG fuel tanks. Procedures for checks, repairs, and safety label installation are included.
- Frames, fuel tanks, hydraulic tanks, and counterweight mounts. Component descriptions and identification are given.
- Operator restraint systems including seat belts and hip restraints. Inspection and function checks are outlined.
- Hood support assemblies, hood doors, pre-cleaners, and related components
Hyster j006 (h6.0 ft europe) forklift service repair manualfusjfjskekmem
The document provides instructions for servicing and repairing various components of a lift truck, including:
- Removing and installing side covers, floor plates, seats, dashes, and hood assemblies.
- Inspecting and servicing the operator restraint system including seat belts.
- Removing and installing seal plates, steering columns, and hood support assemblies.
- Guidelines for putting the lift truck on blocks for maintenance and warnings about stability.
- Diagrams illustrating the locations and attachments of different parts.
Hyster d098 (e100 z) forklift service repair manualfujsefkksekfm
This document provides descriptions and service procedures for parts of an electric lift truck frame, including:
- The frame itself, counterweight assembly, overhead guard, hood, seat assembly, access panels, and label positions.
- It describes the battery compartment, including adjustable spacers to prevent battery movement, warnings about battery size and weight limits, and how to access components under the floor plates.
- The final section covers servicing the battery restraint system, hood, seat assembly, and operator restraint system. It describes how to raise and lower the hood and seat assembly to access the battery, and how to ensure the battery is securely locked in place during operation.
Hyster d098 (e100 zs) forklift service repair manualfusjefjsekksemm
This document provides descriptions and service procedures for parts of an electric lift truck frame, including:
- The frame itself, counterweight assembly, overhead guard, hood, seat assembly, access panels, and label positions.
- It describes the battery compartment, including adjustable spacers to prevent battery movement, warnings about battery size and weight limits, and how to access components under the floor plates.
- The final section covers servicing the battery restraint system, hood, seat, and operator restraint system, including how to raise and lower the hood and seat assembly to access the battery.
Hyster d098 (e70 z) forklift service repair manualfjskkddmmmse
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment prevent battery movement and must be properly adjusted.
- The overhead guard, hood, seat, and battery restraint are removed and installed following specific procedures.
- The counterweight
Hyster d098 (e80 z) forklift service repair manualfjsjefksekkksemm
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment prevent battery movement and must be adjusted properly.
- The overhead guard, hood, seat, and battery restraint are removed and installed following specific procedures.
- The counterweight
Hyster d098 (e100 z) forklift service repair manualfujjsefjkskem
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment control battery movement and must ensure it cannot move more than 13mm in any direction.
- The overhead guard, hood, seat, and battery restraint are part of the operator restraint
Hyster d098 (e100 zs) forklift service repair manualfujsjfjkskekmm
This document provides descriptions and service procedures for parts of an electric lift truck frame, including:
- The frame itself, counterweight assembly, overhead guard, hood, seat assembly, access panels, and label positions.
- It describes the battery compartment, including adjustable spacers to prevent battery movement, warnings about battery size and weight limits, and how to access components under the floor plates.
- The final section covers servicing the battery restraint system, hood, seat assembly, and operator restraint system. It describes how to raise and lower the hood and seat assembly to access the battery.
Yale b878 gdp60 70 ca, glp60-70ca (gp-gdp-glp135-155ca) lift truck service re...fujsekksmem
This document is a service manual that contains sections covering various components of a GDP/GLP60-70CA lift truck, including:
- The frame, counterweight, hood, and overhead guard.
- GM engines, a Perkins diesel engine, cooling system, fuel systems, transmission, differential, drive axle, steering, brakes, hydraulics, controls, tilt cylinders, electrical, instruments, diagnostics, lift cylinders, mast, fasteners, specifications, maintenance, and diagrams.
- Procedures are provided for removing and installing the counterweight, hood, and overhead guard while maintaining stability of the lift truck during maintenance. Capacities and weights of counterweights are listed
Hyster h50 xm (h177) forklift service repair manualjfjkskekfsmem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, overhead guard, hood, side covers, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h65 xm (h177) forklift service repair manualfjskefkksemm
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h55 xm (h177) forklift service repair manualfjjkefkksem
This document provides instructions for servicing the operator module, overhead guard, counterweight, exhaust system, and LED lights of a forklift. It describes removing and installing these components, including warnings about stability and safety when parts that affect the vehicle's center of gravity are removed. Proper use of lifting devices and installation of stabilizing blocks is emphasized. Technical details like component weights and fastener torques are provided.
Hyster h65 xm (h177) forklift service repair manualfjjskefkskem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h50 xm (h177) forklift service repair manualfjskekfkemm
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h45 xm (h177) forklift service repair manualfjjkskekfsmem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
This document provides definitions for common abbreviations used in tractor manuals and descriptions of universal symbols seen on tractor instruments and controls. It defines abbreviations such as 2WD, 4WD, PTO, rpm, and others. It also describes common symbols and their meanings, such as those indicating diesel fuel, engine speed, temperature, and others. The purpose is to guide the operator in understanding the operation of the tractor.
Kohler command pro cv1000 vertical crankshaft service repair manualfusjefjsekksemm
This service manual provides instructions for servicing a vertical crankshaft Command Pro engine models CV940-CV1000. The 10 section manual covers: safety information, tools, troubleshooting, air intake system, fuel system, lubrication system, electrical system, disassembly, inspection/reconditioning, and reassembly. A maintenance schedule in section 1 lists procedures to perform daily, weekly, and every 150-600 hours including checking fluid levels, cleaning components, and replacing spark plugs and air filters.
More Related Content
Similar to Hyster d470 (n35 zr) forklift service repair manual
Hyster h006 (h155 ft) forklift service repair manualfujsjfjkskekmm
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, seats, dashes, and hoods.
2) Inspecting operator restraint systems like seat belts.
3) Removing and installing frames, counterweights, engines, and fuel tanks.
4) Proper blocking and stability procedures when components that affect the vehicle's center of gravity are removed.
Hyster h006 (h155 ft) forklift service repair manualfujdfjjskkkemw
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, the seat, dash, kick panel, and seal plate.
2) Removing and installing the hood support and door assembly, including disconnecting related components.
3) Removing and installing the hood door assembly on each side of the lift truck.
4) Instructions are provided for each component with detailed steps and diagrams to guide the process. Safety warnings are included for working with certain systems like the LPG tank.
Hyster h006 (h135 ft) forklift service repair manualfujfjjjskekemm
This document provides instructions for servicing various components of a lift truck, including:
1) Removing and installing side covers, the seat, dash, kick panel, and seal plate.
2) Removing and installing the hood support and door assembly, including disconnecting related components.
3) Removing and installing the hood door assembly on each side of the lift truck.
4) Instructions for the LPG tank and bracket assembly removal are provided at the end. Safety warnings are given regarding the flammable nature of LPG.
Hyster j006 (h6.0 ft europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing and repairing various components of a lift truck, including:
- Side covers, floor plates, seats, dashes, and hoods. Removal and installation steps are provided.
- Counterweights, mufflers, overhead guards, engines, exhaust systems, and LPG fuel tanks. Procedures for checks, repairs, and safety label installation are included.
- Frames, fuel tanks, hydraulic tanks, and counterweight mounts. Component descriptions and identification are given.
- Operator restraint systems including seat belts and hip restraints. Inspection and functionality checks are outlined.
- Hood support assemblies, hood doors, pre-cleaners, and related components
Hyster j006 (h7.0 ft europe) forklift service repair manualjfksekmmdme
The document provides instructions for servicing and repairing various components of a lift truck, including:
- Removing and installing side covers, floor plates, seats, dashes, and hood assemblies.
- Inspecting and servicing the operator restraint system including seat belts.
- Removing and installing seal plates, steering columns, and hood support assemblies.
- Guidelines for putting the lift truck on blocks for maintenance and warnings about stability.
- Diagrams illustrating the locations and attachments of different parts.
Hyster j006 (h7.0 ft europe) forklift service repair manualfjjskekdmmem
This document provides instructions for servicing and repairing various components of a lift truck, including:
- Side covers, floor plates, seats, dashes, and hoods. Removal and installation steps are provided.
- Counterweights, mufflers, overhead guards, engines, exhaust systems, and LPG fuel tanks. Procedures for checks, repairs, and safety label installation are included.
- Frames, fuel tanks, hydraulic tanks, and counterweight mounts. Component descriptions and identification are given.
- Operator restraint systems including seat belts and hip restraints. Inspection and function checks are outlined.
- Hood support assemblies, hood doors, pre-cleaners, and related components
Hyster j006 (h6.0 ft europe) forklift service repair manualfusjfjskekmem
The document provides instructions for servicing and repairing various components of a lift truck, including:
- Removing and installing side covers, floor plates, seats, dashes, and hood assemblies.
- Inspecting and servicing the operator restraint system including seat belts.
- Removing and installing seal plates, steering columns, and hood support assemblies.
- Guidelines for putting the lift truck on blocks for maintenance and warnings about stability.
- Diagrams illustrating the locations and attachments of different parts.
Hyster d098 (e100 z) forklift service repair manualfujsefkksekfm
This document provides descriptions and service procedures for parts of an electric lift truck frame, including:
- The frame itself, counterweight assembly, overhead guard, hood, seat assembly, access panels, and label positions.
- It describes the battery compartment, including adjustable spacers to prevent battery movement, warnings about battery size and weight limits, and how to access components under the floor plates.
- The final section covers servicing the battery restraint system, hood, seat assembly, and operator restraint system. It describes how to raise and lower the hood and seat assembly to access the battery, and how to ensure the battery is securely locked in place during operation.
Hyster d098 (e100 zs) forklift service repair manualfusjefjsekksemm
This document provides descriptions and service procedures for parts of an electric lift truck frame, including:
- The frame itself, counterweight assembly, overhead guard, hood, seat assembly, access panels, and label positions.
- It describes the battery compartment, including adjustable spacers to prevent battery movement, warnings about battery size and weight limits, and how to access components under the floor plates.
- The final section covers servicing the battery restraint system, hood, seat, and operator restraint system, including how to raise and lower the hood and seat assembly to access the battery.
Hyster d098 (e70 z) forklift service repair manualfjskkddmmmse
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment prevent battery movement and must be properly adjusted.
- The overhead guard, hood, seat, and battery restraint are removed and installed following specific procedures.
- The counterweight
Hyster d098 (e80 z) forklift service repair manualfjsjefksekkksemm
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment prevent battery movement and must be adjusted properly.
- The overhead guard, hood, seat, and battery restraint are removed and installed following specific procedures.
- The counterweight
Hyster d098 (e100 z) forklift service repair manualfujjsefjkskem
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment control battery movement and must ensure it cannot move more than 13mm in any direction.
- The overhead guard, hood, seat, and battery restraint are part of the operator restraint
Hyster d098 (e100 zs) forklift service repair manualfujsjfjkskekmm
This document provides descriptions and service procedures for parts of an electric lift truck frame, including:
- The frame itself, counterweight assembly, overhead guard, hood, seat assembly, access panels, and label positions.
- It describes the battery compartment, including adjustable spacers to prevent battery movement, warnings about battery size and weight limits, and how to access components under the floor plates.
- The final section covers servicing the battery restraint system, hood, seat assembly, and operator restraint system. It describes how to raise and lower the hood and seat assembly to access the battery.
Yale b878 gdp60 70 ca, glp60-70ca (gp-gdp-glp135-155ca) lift truck service re...fujsekksmem
This document is a service manual that contains sections covering various components of a GDP/GLP60-70CA lift truck, including:
- The frame, counterweight, hood, and overhead guard.
- GM engines, a Perkins diesel engine, cooling system, fuel systems, transmission, differential, drive axle, steering, brakes, hydraulics, controls, tilt cylinders, electrical, instruments, diagnostics, lift cylinders, mast, fasteners, specifications, maintenance, and diagrams.
- Procedures are provided for removing and installing the counterweight, hood, and overhead guard while maintaining stability of the lift truck during maintenance. Capacities and weights of counterweights are listed
Hyster h50 xm (h177) forklift service repair manualjfjkskekfsmem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, overhead guard, hood, side covers, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h65 xm (h177) forklift service repair manualfjskefkksemm
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h55 xm (h177) forklift service repair manualfjjkefkksem
This document provides instructions for servicing the operator module, overhead guard, counterweight, exhaust system, and LED lights of a forklift. It describes removing and installing these components, including warnings about stability and safety when parts that affect the vehicle's center of gravity are removed. Proper use of lifting devices and installation of stabilizing blocks is emphasized. Technical details like component weights and fastener torques are provided.
Hyster h65 xm (h177) forklift service repair manualfjjskefkskem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h50 xm (h177) forklift service repair manualfjskekfkemm
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Hyster h45 xm (h177) forklift service repair manualfjjkskekfsmem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Similar to Hyster d470 (n35 zr) forklift service repair manual (20)
This document provides definitions for common abbreviations used in tractor manuals and descriptions of universal symbols seen on tractor instruments and controls. It defines abbreviations such as 2WD, 4WD, PTO, rpm, and others. It also describes common symbols and their meanings, such as those indicating diesel fuel, engine speed, temperature, and others. The purpose is to guide the operator in understanding the operation of the tractor.
Kohler command pro cv1000 vertical crankshaft service repair manualfusjefjsekksemm
This service manual provides instructions for servicing a vertical crankshaft Command Pro engine models CV940-CV1000. The 10 section manual covers: safety information, tools, troubleshooting, air intake system, fuel system, lubrication system, electrical system, disassembly, inspection/reconditioning, and reassembly. A maintenance schedule in section 1 lists procedures to perform daily, weekly, and every 150-600 hours including checking fluid levels, cleaning components, and replacing spark plugs and air filters.
This document is a service manual that provides safety and general information for Command vertical crankshaft engines models CV11-16, CV460-465, and CV490-495. It contains 11 sections covering topics like safety precautions, special tools, troubleshooting, maintenance schedules, specifications, and disassembly/reassembly procedures. The manual instructs technicians on proper service and repair of these engine models.
Kawasaki tj27 d 2 stroke air-cooled gasoline engine service repair manualfusjefjsekksemm
This document is the service manual for a TJ27D 2-stroke air-cooled gasoline engine. It provides information on locating specific topics, lists abbreviations used, covers emission control systems and tampering guidelines, and includes a foreword on safely and properly using the manual for maintenance and repair. The manual contains sections on general information, periodic maintenance, fuel system, engine top end, crankshaft, electrical system, recoil starter, troubleshooting and more.
Kawasaki kel26 a handheld edger service repair manualfusjefjsekksemm
This service manual provides information for servicing a Kawasaki KEL26A handheld edger. It contains general information sections covering safety, specifications, maintenance schedules, torque values, and more. The manual is intended for use by trained mechanics and contains detailed instructions for maintenance and repair procedures.
Kawasaki kbh43 a trimmer brushcutter service repair manualfusjefjsekksemm
This document provides information for servicing trimmer/brushcutter engines produced by Kawasaki Heavy Industries, including model numbers and manuals. It begins with copyright information and warnings against reproducing content without permission. Abbreviations used in service manuals are then defined. The document continues with information on exhaust emission control systems and a foreword on properly using service manuals.
Hyster k005 (h5.00 xm europe) forklift service repair manualfusjefjsekksemm
This document provides repair procedures for various components of a lift truck, including the counterweight, hood, overhead guard, LED lights, and operator restraint system. It describes removing and installing the counterweight, which involves installing eyebolts and a lifting device. The hood repair section discusses adjusting the hood latch and striker. Removal and installation of the overhead guard requires a lifting device and removing/replacing mounting bolts. Replacing LED lights involves disconnecting the light assembly from the harness and mounting bracket. Inspection and repair of the operator restraint system components like the seat belt and hip restraint is also covered.
Hyster h177 (h2.50 xm) forklift parts catalogue manualfusjefjsekksemm
This document is a parts manual for a Challenger H2.00-H3.20XM truck. It is divided into 13 sections covering the frame, engines, fuel system, electrical system, transmission, steering, brakes, hydraulics, mast systems, options, and a numerical index. Section 1 covers the frame and includes diagrams and part numbers for components such as the overhead guard, floorplates, hood, seats, labels, and load backrest extension.
Hyster f187 (s60 ft) forklift service repair manualfusjefjsekksemm
The document provides instructions for repairing components of a transmission. It describes how to remove and replace the transmission's torque converter. Key steps include separating the transmission from the engine, draining the transmission oil, and removing the torque converter. New gaskets and O-rings are installed before reattaching the torque converter housing and transmission housing using capscrews.
Hyster e004 (s100 xmbcs) forklift service repair manualfusjefjsekksemm
This document provides descriptions and instructions for repairing gear pumps. It discusses the basic components and operation of single-stage and tandem gear pumps. The repair process involves removing the pump, disassembling it, cleaning the parts, inspecting for wear, and reassembling. Key steps include separating the housing sections, removing gears/shafts, pulling bearings, and inspecting parts for grooves, scratches, or excessive wear that would require replacement. Seals are commonly worn and need replacing. Care must be taken to properly orient parts and note locations of seals during disassembly and reassembly.
Hyster c160 (j35 xmt) forklift service repair manualfusjefjsekksemm
This document provides descriptions and service procedures for parts of an electric forklift frame including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It describes the battery restraint system which holds the battery in place if the forklift tips over. The battery restraint plate is connected to the frame with a hinge and latch mechanism. Spacers in the battery compartment prevent battery movement. The document provides instructions for raising the battery restraint and hood to access components and ensuring the battery is securely latched in place during operation.
Hyster b098 (e5.00 b europe) forklift service repair manualfusjefjsekksemm
This document provides information about repairing gear pumps. It describes the components and operation of single-stage and tandem gear pumps. The key steps for repair include removal of the pump, disassembly, cleaning and inspection of parts, and reassembly. Worn or damaged seals are a common cause of pump failure. Replacement of seals is often more cost effective than a full rebuild of the pump. Care must be taken during disassembly and reassembly to properly align parts and ensure cleanliness of the hydraulic system.
Cummins onan generator set with power command 3100 controller model (dqba ) s...fusjefjsekksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting procedures, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and instructions for maintenance and repairs.
Cummins onan generator set with power command 3100 controller model (dfcc ) s...fusjefjsekksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets equipped with PowerCommand 3100 controllers. It contains sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and safety instructions for working on the generator set and power control systems.
This service manual provides information to technicians for troubleshooting, testing, and repairing the Hydroject 3000/4000. It contains chapters covering safety, product records, the engine, hydraulic system, electrical system, water system, wheels and steering, and addendums specific to the Hydroject 4000. Technicians are instructed to follow safety procedures, refer to the operator's manual, and only perform maintenance described in this manual.
Cummins onan generator set with power command 3100 controller model (dfab ) s...fusjefjsekksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Cummins onan dqcb generator set with qsk23 g3 engine and power command 2100 c...fusjefjsekksemm
This document is a service manual that provides instructions for servicing generator sets with model numbers DQCA-DQCC that use a QSK23G3 engine and PowerCommand 2100 controller. It contains sections on control operation, circuit boards and modules, troubleshooting, control adjustment and service, servicing the generator, an optional enclosure fuel tank system, and wiring diagrams. The manual provides technical information and safety instructions for working on the generator set components.
Case tr340 tier 4 b (final) alpha series compact track loader service repair ...fusjefjsekksemm
This service manual provides information on servicing and repairing the SR270, SV340, TR340, and TV380 skid steer loaders and compact track loaders. It covers the engine, fuel system, cooling system, lubrication system, power coupling, front and rear axles, hydrostatic drive, brakes, hydraulic systems, frames, wheels, tracks, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual includes introduction sections on safety, fluids, specifications, identification, and basic instructions for servicing. It provides exploded views and specifications for replacement parts.
This document is the service manual for the Greensmaster 1000/1600. It provides information to service technicians for troubleshooting, testing, and repairing components. Safety is emphasized, with instructions to read the manual, wear protective equipment, fuel safely, and more. The manual contents include safety information, product records, engine systems, electrical systems, controls, cutting units, and a grooming reel kit chapter.
Case tr320 tier 4 a alpha series compact track loader service repair manual p...fusjefjsekksemm
This document is a service manual for Case skid steer loaders and compact track loaders. It provides information on safety procedures, torque specifications, product identification, and maintenance of the engine, front axle, rear axle, and other systems. The document contains copyright information, part numbers, and replaces prior service manuals. It instructs technicians to follow procedures carefully when servicing equipment.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. 100 SRM 1185 Repairs - General
General
WARNING
DO NOT make repairs or adjustments unless
you have been properly trained and specifi-
cally authorized to do so. Repairs and adjust-
ments that are incorrect can create dangerous
operating conditions.
DO NOT operate a lift truck that needs repairs.
Report the need for repairs to your supervisor
immediately. If repair is necessary, disconnect
the battery and attach a DO NOT OPERATE tag
to the control handle.
This section contains descriptions of the frame com-
ponents, repair procedures, and assembly informa-
tion. These components include the frame weldment,
door, floor plate, and covers. The overhead guard and
base arms are also covered in this section.
Throughout this section, forward will refer to travel
in the direction of the forks, and left and right will be
from the perspective of an operator in the operator
compartment facing the forks. See Figure 1.
A. LEFT
B. RIGHT
C. FORWARD
Figure 1. Travel Orientation
Description
The frame is available in two sizes: small chassis
and large chassis. The small chassis is used for the
N30ZDR, N35-40ZR, N30ZDRS, and N35-40ZRS
unit and uses a smaller drive unit. The small chas-
sis frame is available with a 368.3 mm (14.5 in.) or
419.1 mm (16.5 in.) battery compartment width.
The large chassis is used for the N35ZDR and N45ZR
unit and uses a larger drive unit. The large chas-
sis frame is available with a 419.1 mm (16.5 in.),
469.9 mm (18.5 in.), or 546.1 mm (21.5 in.) battery
compartment width.
The frame has mounts for the following parts:
• Mast Assembly
• Steering System Parts
• Electrical System Parts
• Hydraulic System Parts
• Door, Floor Plate, Access Panels, and Covers
The overhead guard fastens to the mast. A rear op-
erator guard leg provides protection for the operator
and unobstructed operation of the lift truck. The op-
erator guard leg fastens between the overhead guard
and the frame. Repair procedures for major compo-
nents that fasten to the frame are in separate sec-
tions. See each section for the system that has the
part to be repaired.
Repairs - General
Repair is seldom required on the frame unless the
truck has been structurally damaged. Most truck re-
pairs involve removing the system parts that attach
to the frame. Refer to the appropriate section for the
system that needs repair. To separate the mast from
the frame, refer to the sections Mast, Repair 4000
SRM 1195 and Reach Carriages 4500 SRM 1196.
To replace the load wheels in the base arms, see the
section Periodic Maintenance 8000 SRM 1197 or
Load Wheels in this section.
The caster wheel assembly is part of the steering
assembly. See the section Steering System 1600
SRM 1187 to replace the caster wheel assembly or
the caster wheels.
To replace the drive wheels or tires, see the section
Periodic Maintenance 8000 SRM 1197.
1
3. Covers, Panels, and Plates 100 SRM 1185
WELDING
WARNING
Remove the battery and disconnect the battery
connector before welding. Welding can cause a
fire and/or an explosion. Make sure there is no
oil or grease near the weld area and that the
area is well-ventilated.
Forklift truck frames and components may
have polyurethane paint. Welding, burning, or
other heat sufficient to cause thermal decom-
position of the paint may release isocyanates.
These chemicals are allergic sensitizers to the
skin and respiratory tract irritants. Overexpo-
sure may occur without odor warning. When
performing work, utilize good industrial hy-
giene practices, including removal of all paint
(prime and finish coats) to the metal around
the area to be welded. Use local ventilation,
and/or supplied, air-respiratory protection.
CAUTION
Certain welding repairs require factory ap-
proval. Structural members such as base
arms, axle weldments, and mast components
require written Hyster engineering approval
before repairing or replacing. Contact your
local dealer for factory assistance.
CAUTION
Connect the welding ground clamp as close to
the weld area as possible to prevent welding
current from straying.
Only properly trained, authorized technicians should
perform welding repairs.
Covers, Panels, and Plates
FRONT FRAME PANEL (LEFT AND RIGHT)
Remove the screws from the upper and lower ends of
the front frame panel. Pull the lower end of the panel
away from the frame of the lift truck and gently work
up the side of the panel to pull it from the retainer
clips securing the panel to the frame. Pull the top end
tabs out of the operator compartment cover. Repeat
for opposite side as necessary. See Figure 2.
NOTE: On right-side, front frame panels, ensure the
diagnostic connector cap is positioned correctly to al-
low the cover to seat properly.
To install the panel, position the upper end of the
panel partially into the retaining clip on the frame.
Insert the tabs on the upper end of the panel into
the slots in the operator compartment cover. Work
the sides of the panel into the retaining clips until all
areas of the panel are aligned with the frame. Align
the holes in the panel with the mounting brackets
on the frame and loosely install the screws into the
upper end and lower end of the panel. Make certain
the panel is seated correctly against the frame and
tighten the screws to secure in place. See Figure 2.
Figure 2. Front Frame Panel (Left Side)
2
4. 100 SRM 1185 Covers, Panels, and Plates
Legend for Figure 2
1. OPERATOR COMPARTMENT COVER
2. FRAME
3. LOWER BRACKET
4. LOWER SCREW
5. FRONT COVER PANEL (LEFT)
6. TABS
7. UPPER BRACKET
8. UPPER SCREW
OPERATOR COMPARTMENT COVER
Remove the front frame panels from the lift truck.
See Front Frame Panel (Left and Right). Remove
the two screws securing the operator cover to the
frame brackets. One is located on the lower right
side of the operator compartment above the opera-
tor presence switch. The other is located beside the
overhead guard post mount, at the bottom of the cup
holder. Pull the operator compartment cover up from
the front right corner. Continue pulling the cover up
along the edge of the frame in both directions until
the cover is free from the retaining clips. See Fig-
ure 3.
1. OPERATOR COMPARTMENT COVER
2. RETAINING SCREW
3. FRAME
4. FRONT COVER PANEL (LEFT)
Figure 3. Operator Compartment Cover
To install, position the cover over the electrical com-
partment. Align the lip of the cover to the retaining
clips. Press the lip of the cover into the retaining
clips starting at the overhead guard post and con-
tinue around until completely seated. Align the holes
in cover with the mounting brackets and install re-
taining screws as removed. Install the front frame
panels to complete assembly. Refer to Front Frame
Panel (Left and Right).
DRIVE UNIT COMPARTMENT DOOR
Completely loosen the two socket head capscrews se-
curing the drive unit compartment door closed. The
screws are spring-loaded and are retained to the door
by clips. Pull the door open on its hinges. To close,
push the door closed and start both socket head cap-
screws loosely into the mounting holes. When both
screws are started, verify that the door seats prop-
erly against the frame and tighten the screws.
DOOR PAD
Open compartment door and remove the seven cap-
screws holding the pad to the door. Lift the pad over
the steering mechanism and remove.
To instal the pad, lower it over the steering mecha-
nism and position it onto the door. Install the seven
socket head capscrews as removed.
OPERATOR BACK PAD
Side-Stance Models
Remove the five socket head capscrews retaining pad
to the adjuster mechanism and remove the pad.
To install, position the back pad onto the adjuster
mechanism and loosely install the five socket head
capscrews as removed. Verify that the back pad seats
properly to the adjuster mechanism and tighten to
secure as removed.
Forward-Stance Models
NOTE: On models with Aft Travel controls, guide
the aft travel control handle wiring harness into/out
of the frame when installing/removing the operator
back pad.
Remove the operator compartment cover to access
the screw securing the front of the operator back pad
to the frame. Remove the two screws securing the
operator back pad to the frame and remove the pad
from the frame.
3
5. Load Wheels 100 SRM 1185
To install, position the back pad against the frame
as removed. Install the two screws securing pad to
frame as removed, and reinstall the operator com-
partment cover.
OPERATOR FRONT PAD
Remove the operator compartment cover from the lift
truck. See Operator Compartment Cover. Remove
the screws securing the pad brackets to the frame.
Pull the top of the pad away from the frame and then
lift the pad from the lower retaining clips.
To install, position the lower pad brackets into the
retaining clips. Position the upper end of the pad to
the frame. Align the pad bracket holes and install the
screws to secure the pad in place. Install the operator
compartment cover in place.
CASTER WHEEL COVER
Remove the two socket head capscrews on top of the
caster wheel cover and lift cover from the clips secur-
ing it to the frame.
To replace, fit the bottom of the cover into the clips
inside the opening and slide the cover into place. In-
stall two socket head capscrews to secure the top of
the cover in place.
Load Wheels
REMOVE
Slightly raise the base arms and support on blocks as
described in the Periodic Maintenance 8000 SRM
1197. Make sure the base arms and load wheels do
not support any weight.
1. Remove the nut, washers, and axle bolt. See Fig-
ure 4.
2. Remove the load wheels from the hanger brack-
ets.
1. AXLE BOLT
2. WASHER
3. HANGER
BRACKETS
4. AXLE SLEEVE
5. BEARING
6. LOAD WHEEL
7. NUT
Figure 4. Load Wheels
3. Remove the axle sleeves and bearings from the
load wheels. Check for wear or roughness as
the bearings are rotated. Replace both bearings
if wear or roughness is noted. Inspect the load
wheels for damage or wear. Replace as necessary.
CAUTION
Use a hammer and a soft punch when removing
bearings to avoid damage to bearings and/or
load wheel.
4. Remove the hanger bracket from the base arms
and inspect thoroughly. Inspect the base arms
thoroughly for damage.
INSTALL
WARNING
Cleaning solvents can be flammable and toxic
and can cause skin irritation. Wear protection
when handling solvents and always follow the
recommendations of the manufacturer.
CAUTION
1. Clean all parts with solvent and inspect thor-
oughly. Replace damaged parts as necessary.
2. Apply lithium grease to the pivot contact on the
hanger brackets. Position the hanger brackets
into the base arms and install the load wheels
and axle sleeves into the hanger brackets. See
Figure 5.
4
6. 100 SRM 1185 Overhead Guard Replacement
1. PIVOT CONTACT
2. HANGER BRACKET
3. LOAD WHEELS
4. BASE ARM
Figure 5. Hanger Bracket Pivots
CAUTION
The bearings are replaced by pressing on the
outer race of the bearing only. Pressing or tap-
ping on the inner race will damage the bearing.
Use a suitable driver when installing bearings
to avoid damage to bearings and/or load wheel.
Replace bearings in sets to maintain proper
wheel loading and operation.
NOTE: Load wheel assemblies that have axle bolts
equipped with lube fittings use side-shielded bear-
ings and must be greased. Assemblies with axle bolts
not equipped with lube fittings use sealed bearings
and cannot be greased.
3. Install the bearings into the load wheels.
a. Sealed Bearings - Install the bearings into
the load wheel assemblies. Position the axle
sleeve into the assembly. Apply antiseize lu-
bricant to the axle bolt.
b. Side-Shielded Bearings - Install one bear-
ing into the load wheel with the shielded side
facing out. Fill the cavity inside of the load
wheel with grease. Install the other bearing
into the load wheel with the shielded side fac-
ing out. Position the axle sleeve into the as-
sembly.
4. Apply grease to the pivot contact on the hanger
brackets. Position the hanger brackets into the
base arms and install the load wheels and axle
sleeves into the hanger brackets.
5. Install a washer onto the axle bolt. Install the
axle bolt through the hanger brackets, bearings,
and axle sleeve with the threads to the inside of
the base arms.
6. Install washers and nuts to the axle bolts. Torque
to 68 N•m (50 lbf ft).
NOTE: If axle shafts are equipped with lube fittings,
grease to fill load wheel cavity. Refer to Periodic
Maintenance 8000 SRM 1197 for regularly sched-
uled maintenance procedures.
Overhead Guard Replacement
WARNING
DO NOT weld mounts for lights or accessories
to the overhead guard. The strength of the
overhead guard can be reduced by welding or
heating.
Install lights and accessories or their mounts
with clamps. The strength of the overhead
guard can be reduced if holes are drilled in the
wrong location or are too large. Contact your
lift truck dealer before welding or drilling
holes in any part of the overhead guard.
The overhead guard assembly is heavy. Be sure
that all lifting devices (hoists, cables, chains,
slings, etc.) are suitable and of adequate capac-
ity to lift the overhead guard.
The overhead guard assembly consists of the over-
head guard and a support post. See Figure 6 and
Figure 7. The overhead guard is attached to the mast
with six capscrews (2) and lockwashers (3). The top
of the support post is bolted to the overhead guard.
The bottom of the post fits into a retainer in the drive
unit compartment.
5
8. Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
9. 100 SRM 1185 Overhead Guard Replacement
Legend for Figure 6
1. OVERHEAD GUARD
2. CAPSCREW
3. LOCKWASHER
4. PLUG (W/O HEAD LAMPS)
5. CAPSCREW
6. CAPSCREW
7. PLUG
8. SUPPORT POST
9. BUSHING
The size of the overhead guard varies depending
upon the battery compartment size.
REMOVE
Refer to WARNING (above) before performing ser-
vice to any overhead guard components.
1. Attach a suitable lifting device to the overhead
guard.
2. Remove the two capscrews (6) retaining the sup-
port post to the overhead guard. See Figure 6.
Pull the support post out of the retainer in the
lift truck frame. Remove the support post.
3. Remove the six capscrews (2) and lockwashers (3)
retaining the overhead guard to the mast. Lower
the overhead guard to the floor.
INSTALL
Refer to WARNING (above) before performing ser-
vice to any overhead guard components.
1. Attach a suitable lifting device to the overhead
guard.
2. Align the overhead guard with the top of the mast
and install the six capscrews (2) and lockwash-
ers (3). See Figure 6. Torque the capscrews to
149 N•m (110 lbf ft).
3. Slide the support post into the retainer in the
lift truck frame. Install the two capscrews (6)
retaining the support post to the overhead guard.
7
11. 100 SRM 1185 Overhead Guard Replacement
Legend for Figure 7
1. OVERHEAD GUARD
2. CAPSCREW
3. LOCKWASHER
4. PLUG (W/O HEAD LAMPS)
5. CAPSCREW
6. CAPSCREW
7. SUPPORT POST
8. BUSHING
FRONT LIGHTS
Two front (head) lights are mounted by their brackets
to the front of the overhead guard.
Bulb Replacement
1. Remove the four screws securing the lens re-
tainer and lens to the assembly. Hold the lens
in place until all screws have been removed
then remove the lens and retainer. Replace as
required. See Figure 8.
2. Remove the bulb from the fixture and replace
with new.
CAUTION
Overtightening the screws can break the lens.
3. Position the lens and the retainer to the fixture
and install the four screws.
1. BRACKET
2. RETAINING CAPSCREW AND NUT
3. SCREW
4. LENS RETAINER
5. LENS
Figure 8. Lens Removal
9
12. Overhead Guard Replacement 100 SRM 1185
Assembly Replacement
1. Disconnect the wiring harness from the light as-
sembly connector.
2. Remove the nut and washers from the capscrew
securing the headlight assembly to the bracket.
Slide the capscrew from the bracket and remove
the headlight. See Figure 9.
3. Remove the bracket from the overhead guard and
replace, if necessary.
4. Install bracket to overhead guard, if removed.
5. Position the light assembly to the bracket and in-
stall capscrew and attaching hardware. Tighten
slightly to allow for adjustment.
1. ADJUSTMENT SLOT
2. ADJUSTMENT BOLT
3. OVERHEAD GUARD
4. WIRING HARNESS
5. HEADLIGHT
6. CONNECTOR
7. WIRE CLAMP
8. ATTACHING HARDWARE
Figure 9. Head Light Mounting
10
13. 100 SRM 1185 Overhead Guard Replacement
Rear Work and Caution Light
The rear work and caution lights are options that
mount to the overhead guard near the rear of the
truck. Several configurations of these assemblies are
available and connect to the options harness. To re-
pair the light assemblies, perform the following pro-
cedures. Some repairs may not require total disas-
sembly. Perform only the steps necessary to safely
complete the required service. See Figure 10.
The work light is very similar to the front light, ex-
cept for its mounting platform and location. To re-
pair or replace the work light, refer to the instruc-
tions for repairing or replacing the front lights. See
Front Lights.
Caution Light
1. Move the lift truck to a safe, level area and com-
pletely lower the mast. Turn the key switch to
the OFF position and attach a DO NOT OPER-
ATE tag to the control handle. Block the drive
wheel to prevent unexpected movement.
2. Disconnect the battery power cable connector
from the truck connector located on the right side
of the frame. Pull the battery cable connector
handle to separate the battery connector from
the truck connector.
3. Remove the nuts securing the cage to the light
assembly. Remove the cage.
4. Remove the screws and washers securing the
lens globe to the light assembly. Remove the lens
globe.
5. Remove the bulb from the fixture and replace if
necessary.
6. Connect the battery and turn the key switch to
the ON position. Test for proper operation.
7. Position the lens globe to the light assembly. In-
stall screws to secure.
8. Position the cage onto the studs of the light as-
sembly. Install nuts and washers onto studs.
9. Remove blocks from the wheel and return to ser-
vice.
1. CAGE
2. GLOBE
3. STUDS AND NUTS
4. UPPER MOUNTING FLANGE
5. LOWER MOUNTING FLANGE
6. SCREW
7. MOUNTING BRACKET
8. WORK LIGHT WITH ADJUSTABLE BRACKET
9. WORK LIGHT WIRING HARNESS
10. STROBE WIRING HARNESS
Figure 10. Rear and Caution Light
11
14. Painting Instructions 100 SRM 1185
Painting Instructions
WARNING
Some frames and components are painted with
polyurethane paint. Welding, burning, or other
heat sufficient to cause thermal decomposition
of the paint may release isocyanates. These
chemicals are allergic sensitizers to the skin
and respiratory tract irritants. Overexposure
may occur without odor warning. When heat
must be applied, use good industrial hygiene
practices, including removal of all paint (prime
and finish coats) to the metal around the area
to be heated. Use local ventilation, and/or sup-
plied, air-respiratory protection.
Cleaning solvents may be flammable and/or
toxic and may cause skin irritation. Always
wear proper eye and skin protection.
Always use solvents and paints in an area with
adequate ventilation. DO NOT use solvents or
paints near heat, fire, or electrical equipment
that can make sparks. Follow the paint manu-
facturer’s instructions and precautions.
CAUTION
DO NOT put tape on cylinder rods to protect
from paint. Use a thick layer of multipurpose
grease to protect cylinder rods. Cylinders can
be damaged if operated with tape on the cylin-
der rod.
1. Clean the surface to be painted. Use a solvent
on surfaces to be painted to remove grease and
oil before sanding. DO NOT use solvent to clean
new paint. Make sure all oil and grease is re-
moved.
2. Use sandpaper to remove the top surface of
paint and rust from the metal. All metal sur-
faces where the paint has been removed to the
bare metal must be primed. Apply primer BE-
FORE applying the paint.
3. Protect all surfaces that will not be painted. DO
NOT paint:
All Plastic Covers
Steering Handle
Dash Display
Control Handles
Labels and Information Plates
Operator Pads
Tires and Load Wheels
Chains and Hoses
Battery Connectors
All Switches
Cylinder Rods
Pumps and Motors
Wiring Harnesses or Connectors
CAUTION
Protect electrical components, wiring, and
electrical contacts from overspray.
4. Paint the surfaces using Hyster approved paints.
Follow the proper paint scheme for your lift truck
model (refer to the Parts Manual for specific in-
formation on paint for your lift truck).
5. Install new safety labels. See Safety Labels Re-
placement.
12
15. 100 SRM 1185 Safety Labels Replacement
Safety Labels Replacement
WARNING
Safety labels are installed on the lift truck to
give information about operation and possible
hazards. It is important that all safety labels
are installed on the lift truck and can be read.
DO NOT add to or modify the lift truck. Any
change to the lift truck, the tires, or its equip-
ment can change the lifting capacity. The lift
truck must be rated as equipped and the name-
plate must show the new capacity rating. Con-
tact your lift truck dealer for a replacement
nameplate.
Cleaning solvents can be flammable and toxic
and can cause skin irritation. When using
cleaning solvents, always follow the recom-
mendations of the manufacturer.
If an adhesive plate or label must be replaced, use
the following procedure to install a new label or plate.
See Figure 11 and Figure 12.
1. Clean area with an oil-free cleaner to remove all
oil, grease, and foreign matter. Wipe until com-
pletely dry.
2. Carefully remove only the paper backing from
adhesive. DO NOT touch adhesive surface with
hands or remove front mask from label or plate
face.
3. Exposed adhesive face must be free from all for-
eign matter before positioning label or plate on
surface.
4. Press label or plate down firmly making sure that
all corners are stuck down tight. Make sure that
all air is removed from under the label or plate
and the corners and edges are tight. DO NOT
attempt to move the label or plate once it has
been stuck down.
1. MULTIFUNCTION CONTROL LABEL
2. NAMEPLATE
3. NAMEPLATE COVER
4. RIVET
5. HYDRAULIC FUNCTION DECAL
Figure 11. Operator Compartment Label
Placement
13