Downloaded 10 times
Hybrid iv camera dolly - Chapman UK
- 1. © 2013 Chapman/LeonardStudio Equipment, Inc. Hybrid TM IV Camera Dolly USER GUIDE Operational Instructions & Specifications Hybrid TM IV
- 2. The Operator shouldbe Qualified. For Assistance Please call our 24 hour Customer Service at 1-888-883-6559. © 2001 No part of this manual may be reproduced or electronically transmitted without the written permission of Chapman/Leonard Studio Equipment, Inc.Revision - 05/2014 Ohio 15919 Industrial Parkway Cleveland, OH 44135 Toll Free: 888-758-4826 216-241-4800 Fax: 216-241-4805 Customer Service at 888-883-6559 or 818-764-6726. Chapman / Leonard Certified Locations: Louisiana 668 Distributors Row Suite E Elmwood Business Park New Orleans, LA 70123 Toll Free: 888-758-4826 504-731-6050 Fax: 504-731-6051 Florida Orlando, Florida 32837 Toll Free: 888-337-8243 407-851-3456 Fax: 407-855-1653 New York 38-75 11th Street Toll Free: 888-758-4826 Fax: 718-389-1899 Texas 1901 E. 51st Street Toll Free: 888-758-4826 512-473-0084 Fax: 512-473-0042 MAIN OFFICE 12950 Raymer Street, North Hollywood, CA 91605 www.chapman-leonard.com Toll Free: 888-883-6559 818-764-6726 Fax: 818-764-6730 Rentals 818-764-4347 Leasing 818-764-9391 Accounting UK and Europe Chapman Leonard Studio Equipment, Ltd. Unit 2 North Orbital Commercial Park Napsbury Lane, St. Albans, Herts www.chapmanleonard.com +44 1 727 838424 Fax: +44 1 727 852241 New Mexico 5650 University Blvd. SE Albuquerque, NM 87106 Toll Free: 888-758-4826 Fax: 505-227-2578 Georgia 120 Parkwest Drive #D Toll Free: 888-758-4826 Fax: 678-583-1858
- 3. The Operator shouldbe Qualified. For Assistance Please call our 24 hour Customer Service at 1-888-883-6559. © 2001 No part of this manual may be reproduced or electronically transmitted without the written permission of Chapman/Leonard Studio Equipment, Inc.Revision - 05/2014 CONTENTS 1 Specifications 3 Geometry Lever 4 Arm Markers 9 Fast Mode 10 Detent Bypass 10 Float Mode 13 Brakes 19 Upper and Lower Board Setup Modes 24 Accessories
- 4. 1. Conventional Mode 2.Crab Mode 3. Round Mode Steering modes The Universal Stop Valve controls arm movement with smooth, feathered stops. Adjustments to the Universal Stop Valve can be made without tools or the need to remove any covers or access plates. The Hybrid IV has a new Valve Control Float A new tire design The Side Board System The Hybrid IV has a built-in heat control system in the hydraulic system to maintain a minimum hydraulic oil tempera- ture of 70ºF. This maintains optimum performance in even the coldest environment. Hybrid TM IV Specifications The Hybrid IV in Low Profile Mode with Vertical Boom Travel 43 in./1.09 m (Low Plate Setup) (Low Plate Setup)
- 5. HYBRID TM IV Camera Dolly Stripped DownCarrying Weight = 395 lbs. (180 kg) Maximum Payload with Strut Attached = 700 lbs. (317.5 kg) 880mm Track Configuration (Legs are set at 80 degrees) CHAPMAN 880mm Track Standard Track Configuration (Legs are set at 12 degrees) 241/2 inch Track Low Profile Extension CHAPMAN 64.2” 4.4” HYBRIDIV 21.4” CHAPMAN 53” 17” 19” 14” HYBRIDIV 0˚ 12.9˚ 45˚ 90˚ 180˚ 90˚ 45˚ 12.9˚ 0˚ Standard Track Standard Track 12˚ Standard Track 80˚ 880mm Track 37” 39” Top View of Leg Configurations Compact & Narrow Track Configuration (Legs are set at 0 degrees) With 7 in. Extension With 7 in. Extension 2113/16 inch Track 29.5” 27” 62” 47.2”
- 6. Hybrid TM IV Geometry Lever SetupLeg Positions Geometry Lever Comments Standard EURO Track 80º Standard Track 12.9º º 241/2 Track Narrow Profile 0º º Compact Profile 180º 0º 168º 1/2 Track 12º 1/2 Track º 0º or 180º in all situations. The lever has three positions. Before the Geometry Lever is moved, the transmission must first be shifted 0º or 12º positions, the Geometry Lever must be moved to the left toward the center line of the Dolly (Inboard). A sticker is mounted near the Geometry Lever as a reminder. Wall Hugger Configuration The Asymmetrical placement close to a wall or a more stable platform for the Operator. Tip: Use the QuickJack to help make quick leg changes
- 7. Hybrid TM IV Arm Markers ColoredVelcro Markers attach to the Arm (Upper and Lower). They can be repositioned to different locations on the Arm Precise, repetitive Stops are possible at all speeds. An improved Stop Valve System allows even faster, smoother stops. adjustment that can be performed in the field by a qualified technician. Marker Indicator Markers Lined Up
- 8. Hybrid TM Conventional Mode therear wheels pivot as the operator Crab Mode all wheels turn in uni- Round Handles. Control Pins can be set to limit which modes can can make transitions with confidence. Never use pliers or channel locks on any part of the Dolly. 1. Shift fully to clear the (Halfway between Crab/ Conv. or Crab/Round.) 2. shift into Round, Crab or Conventional Modes. If the transmission still NOTE Locked Position FREE SHIFTING BETWEEN ALL SELECTIONS BOTH PINS OUT SHIFTING BETWEEN CRAB & CONVENTIONAL ONLY TOP PIN OUT BOTTOM PIN IN SHIFTING BETWEEN CRAB & ROUND ONLY TOP PIN IN BOTTOM PIN OUT LOCKED IN CRAB ONLY BOTH PINS IN 2 1
- 9. ” ” Crab Steering Mode Hybrid TM The HybridIV can be shifted smoothly into either Round the course of a shot, even while with confidence. is a new feature of the Hybrid IV. The Dolly can now be turned completely within it an ideal choice for is the selection used most any direction. The camera lens maintains its orientation to the Conventional Steering Mode Round Steering Mode Minimum Turn Radius 20 inches Minimum Turn Radius 31 inches
- 10. feels loose. Thenturn the bottom collar until it can be removed. 1 Hybrid Series of Dollies. 2 Column. 3 4 5 screw and collar. Test the dolly by 76 Make sure that the wheels are all oriented Hybrid TM
- 11. Hybrid TM The Universal StopValve The UP Feathering Lever The DOWN Feathering Lever - Control Valve Handle removed for clarity. When making Stop Adjustments: 1. Be certain the Arm is well beyond the desired Stop point. Then turn the Lever in beyond the desired Stop point. 2. Open the Main Control Valve to approach the desired Stop. 3. Open Lever to achieve movement until the desired Stop point is reached. 4. Close the Main Control Valve. For rapid deceleration beyond the normal for this system, the Dolly Grip can use the Stop Valve to initiate the Stop, then finalize the Stop with the Main Control Valve. DOWN UP More Travel Less Travel Push TurnTurn DOWN Less Travel More Travel Push Turn Turn UP
- 12. WARNING! Failure to placethe Control Valve in the Neutral position may cause the arm Hybrid TM IV Fast Mode push the arm down when the control value is opened. The Fast Mode Value is located on the rear left side of the NOTE
- 13. WARNING! Hybrid TM IV Detent Bypass NOTE: theArm is now reverse direction without hesitation. Therefore, the Float position is achieved. Additionally the Grip can select their own Detent as preferred for a smoother transition from an upward or downward direction. New to the Hybrid IV dolly is the ability to eliminate the detent feature of the Control the Detent feature. There are only two Hybrid TM IV Float Mode A new feature of the Hybrid IV dolly is the ability to fine tune how the arm reacts to the Control Valve Handle. The The Detent Bypass is ON when the button is pushed IN. It is OFF when the button is pulled out.
- 14. Hybrid TM The Valve ControlHandle doubles as into the Foot Pump. Hybrid TM Do not attempt maintenance on the Start Button For Optimal Safety Electrical Ground
- 15. Hybrid TM IV Brakes - incline. Hybrid TM clearance of5/16 inch can be adjusted down to zero. In the Adjustable Detent Control System this can be felt as the Off position is between the Detents. qualified technician. Valve Control Handle Foot Pump
- 16. The default position Hybrid TM Flipped 12 3 4 Remove Quick Release Pin Replace Quick Release Pin and Tighten Nut Foot Rest Other Leveling Head Options The same Set Up as shown above, but Head in the Normal Up position BACK POSITION The payload on can be increased to 700 lbs. if the Support Strut is in place. FRONT POSITION For PayLoad Over 350 lbs BACK POSITION
- 17. Hybrid TM Head into place. CamLever Button on the side. The Head will now rotate Payload.
- 18. Hybrid TM The Narrow SideBoards attach to either side of the Hybrid IV. They slide into place and are secured to the chassis with two thumb screws. As shown in this picture. Low Mode Setup. The Standard Side Boards attach to either side of the Hybrid IV onto the Narrow Side Boards are secured to the chassis with two thumb screws. connects to the Standard Side Board.
- 19. The Standard SideBoards are also adjustable for and aft on the the board to the desired location. Position lock down knob. Hybrid TM The Side Boards may be moved to the rear of the Dolly for easy access to the front thumb screw. Then move the board forward to access the rear thumb screw.
- 20. The Adjustable FrontBoard attaches with Board in either the Upper or Lower position. Hybrid TM A latch is located on the Chassis to hold the Adjustable Front Board or the Lift Pins in place. 2 - 43 1
- 21. Hybrid TM IV Upper andLower Board Setup Modes attached to the Hybrid IV, a stable platform allows the Grip to move the Dolly with a Camera Operator on board. Full Lower Side Board Setup
- 22. Hybrid TM Full Side BoardSet Up (Upper or Lower) Standard Side Board Set Up Narrow Side Board Set Up Boards are only used in the Upper Position. 1R 6 1L 6 4 4 22 5R 5L3 4 7R 7L 22 1R 1L 3
- 23. 7L 7R Hybrid TM IV Accessories Narrow SideBoard (Left) Front Board (Adjustable) Narrow Corner Board (Left) Dolly Seat w/Collar Front Lift/Push Bars Rear Lift/Push Bars Seat Offset Dolly Nose Seat Head w/Nose L Plate Low Camera Plate Accessory Cart Cover Hybrid IV User Guide Location 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 M R M R U L&R U U M F M F M F M F M F M A U A U F M A M L M L B B B M R M R M R B B M A M L M L M A M A B B B B B Number 1L 1R 2 3 4 5L 5R 6 7L 7R Left Rear (Aft) 6
- 24. Hybrid TM U Upper M Middle B LLeft Side R F Front A Aft (Rear) LEGEND 1R 1L Nose Seat Left Side
- 25. Hybrid TM improve performance onFloors, Hardwood, Track and behind tire squeaks and the tendency of tires to stick to Use the same spray to clean the tires.
- 26. FOR USE WITHALL CHAPMAN DOLLIES the lower rear Side Board Hole. the lower center Side Board Hole. the center Side Board Hole. Easily lifts the Hustler dolly Easily lifts the Hybrid dolly Easily lifts the PeeWee dolly for a to a different side board hole.
- 27. Hybrid TM TM IV For Metal Neverdirectly spray the Dolly with water. Use soap and water applied to a cloth or paper towel, or preferably a brush to wipe down the rubber and metal parts of the Dolly. the finish. A clean Dolly will ensure optimum performance with Performance on Tile Floors, Hardwood, Track and even on Concrete. Use the same spray to clean the Tires. For Rubber and Plastic Hybrid TM IV Optional Accessories The optional Rainhouse protects the camera and operator from the elements. Also available in an opaque sunshade version. Rear Deck Board Grip Pouch
- 28. Hybrid TM Use all four makea move with Bar per end or per side may cause injury. Bars from the Accessory Cart to remove the Dolly are fully seated and the of the Hybrid IV is 395 lbs. Remove the Lifting Bars from the dolly and place them in the crate. Accessories that come off the Hybrid IV to be placed in or on the Accessory Cart. The dolly is cradled and no additional bolts or straps are needed. One side of the Accessory Cart Crate can be lowered to form a ramp. The Accessory Cart can then be wheeled
- 29. Hybrid TM Dolly must beproperly crated before shipment. If no bays are available, please park on Raymer Street and advise the Rental Office of your arrival. Our Rental Staff is well trained to process equipment and documents efficiently *ALL RENTALS must be returned by 10:00 AM at the North Hollywood Facility. 12950 Raymer Street North Hollywood, CA 91605 n Rental Office Hours: Monday - Friday: 7:00 AM – 6:00 PM Saturday: 8:00 AM – 12:00 PM Sundays: CLOSED 210 118 405 SHERMAN WAY RAYMER ST. COLDWATERCYN. 170 134 101 118 N