This document provides instructions for servicing a chainsaw, including dismantling, cleaning, inspection and assembly of various systems. It outlines safety regulations that must be followed when working on the chainsaw. Technical specifications are provided for the 570 and 575XP models. A list of required service tools is included. The sections cover the starter, electrical system, clutch, lubrication system, carburetor, tank unit, anti-vibration system, piston/cylinder, crankcase and crankshaft. Instructions are given for checking the chain brake and chain catcher safety equipment.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. CONTENTS
Introduction.................................................. 3
Safety regulations ....................................... 4
Symbols ....................................................... 5
Technical data.............................................. 6
Service tools ................................................ 8
Service data ............................................... 10
Safety equipment....................................... 12
Starter......................................................... 18
Electrical system ....................................... 20
Centrifugal clutch...................................... 26
Lubrication system ................................... 28
Carburettor................................................. 30
Tank unit..................................................... 40
Anti-vibration system................................ 42
Piston and cylinder ................................... 43
Crankcase and crankshaft........................ 49
3. INTRODUCTION
English – 3
General
This Workshop Manual provides a comprehensive
description of how to trouble shoot, repair and test the
chainsaw. A description of different safety measures that
should be taken during repair work is also given.
Safety
Note! The section dealing with safety should be read
andunderstoodbyallwhocarryout repairandservice
work on the chainsaw.
Warning symbols can be found in this Workshop Manual
and on the chainsaw. See page 3. A new warning symbol
mustbeappliedassoonaspossibleifawarningsymbolon
the chainsaw has been damaged or is missing to ensure
the greatest possible safety when using the chainsaw.
Tools
Specialtoolsmustbeusedduringspecificsteps.Allservice
tools are listed in the Workshop Manual. Usage is evident
from respective sections.
Always use Husqvarna original parts:
• Spare parts
• Service tools
• Accessories
Target Group
When producing this Workshop Manual the assumption
has been made that personnel who use it have general
knowledge in the repair and service of small engines.
The Workshop Manual must be read and understood by
personnel who are to carry out repair work and service on
the chainsaw. The Manual is also suitable for use when
training new employees.
Modifications
Modifications will be successively introduced on the
chainsaw during production. When these modifications
affect servicing and/or spare parts, separate service
information will be sent out on each occasion. This means
that in time this Workshop manual will become out of
date. In order to prevent this, the Manual should be read
together with all service information issued concerning
the chainsaw in question.
Layout
This Workshop Manual can be used in two different
ways:
• For the repair of a particular system on the
chainsaw.
• Dismantling and Assembly of the entire chainsaw.
Repair of a particular system
Whenaparticularsystemonthechainsawistoberepaired,
proceed as follows:
1. Look up the page for the system in question.
2. Carry out the sections: Dismantling
Cleaning and inspection
Assembly
Dismantling and Assembly of the entire chainsaw
Proceed as follows when the entire chainsaw is to be
dismantled and assembled:
1. Look up page 19, which deals with the Starter and
carry out the instructions under the heading
Dismantling.
2. Leaf forward in the book and carry out Dismantling
in the order given in the sections.
3. Go back the the Starter on page 1 and carry out the
instructions under Cleaning and inspection.
4. Leaf forward in the book and carry out Cleaning
and inspection in the order given in the sections.
5. Order or take out all requisite spare parts from the
stores.
6. Look up page 47 which deals with the Crankcase
and carry out the instructions under Assembly .
7. Leaf forward in the book and carry out Assembly
in the order given in the sections.
To improve understanding some sections provide a
Description first of the actual unit.
Numbering
Position references to components inside the figures are
designated A, and B, etc.
The figures are number 1, 2 etc.
The position references figure numbers restart in each
new section.
4. SAFETY REGULATIONS
4 – English
WARNING!
The warning text warns of the risk of
personal injury if the instructions are
not followed.
General instructions
The workshop where chainsaw repairs are to be done
must be equipped with safety equipment as set out in
local regulations.
No one may repair the chainsaw unless they have read
and understood the contents of this Workshop Manual.
ThisWorkshopManualcontainsthefollowingwarningtexts
in relevant places. Warning texts are positioned before the
procedures they refer to.
Special instructions
The fuel used in the chainsaw has the following hazardous
properties:
1. The fluid and its fumes are poisonous.
2. Can cause skin irritation.
3. Is highly inflammable.
The bar, chain and clutch cover (chain brake) must be
fitted before the saw is started otherwise the clutch can
work loose and cause personal injury.
Wear ear-muffs when test running.
Do not use the saw until it has been adjusted so that the
chain remains still when idling.
After test running, do not touch the muffler until it has
cooled. Risk of burn injuries.
Insufficient lubrication of the chain can result in the chain
breaking,whichcancauseseriousorevenlife-threatening
injury.
Ensure that the spring in the starter does not fly out and
cause personal injury.
If the spring tension is activated on the starter pulley
when it is to be taken up, the spring can fly out and cause
personal injury.
Checkthatthebrakeisappliedwhenremovingthepressure
spring on the chain brake. Otherwise the pressure spring
can fly out and cause personal injury.
Afterrepair,thechainbrakemustbecheckedinaccordance
with the instructions on page 16.
When replacing the crankshaft bearings note that the
crankcase halves are hot. Wear protective gloves
Do not direct the compressed air jet towards the body
when using compressed air. Air can penetrate into the
blood circulation, which means mortal danger.
NOTE!
This text warns of material damage if the ins-
tructions are not followed.
!
5. SYMBOLS
English – 5
Symbols on the chainsaw
The following symbols are moulded into the chainsaw
casing.
Symbols in this Workshop Manual
This symbol indicates a risk of personal
injury if instructions are not followed.
Choke
Switch for hand grip heater
Fuel filler
Stop button
Screw to adjust chain lubrication
Chain oil filler
6. 6 – English
TECHNICAL DATA
Displacement Bore Stroke Max. power/rpm
cm3
/ cubic inch Ømm/Øinch mm/inch kW/hp/ rpm
570 67,9 cm3
/4.1 49 mm/1,9" 36/1,4 3,6/4,9, 9600 rpm
575XP 73,5 cm3
/4.5 51 mm/2,0" 36/1,4 4,0/5,5, 9600 rpm
Guide bar length Chain speed at max. Chain pitch Drive link
cm/inch power and 9600 rpm mm/inch mm/inch
m/s
570 16-81/18-32 21,4 9,52/3,8 1,5/0,058
575XP 16-81/18-32 21,4 9,52/3,8 1,5/0,058
Spark plug gap Ignition system Air gap Carburettor type
mm/inch mm/inch
570 0,5/0,02 SEM/CD/COT 0,30 mm/0,012 Zama C1M-EL28
575XP 0,5/0,02 SEM/CD/COT 0,30 mm/0,012 Zama C1M-EL28
7. TECHNICAL DATA
English – 7
Idling speed Engage speed Max. speed Spark plug
rpm rpm rpm
570 2 700 3600 13600 NGK BPMR7A
Champion RCJ 7Y
575XP 2 700 3600 13600 NGK BPMR7A
Champion RCJ 7Y
Fuel tank volume Oil pump capacity Oil tank volume Automatic oil pump
Litres/US pint cm3
/min Litres/US pint
570 0,70/1,5 5-22/xx rpm 0,40/0,8 Yes
575XP 0,70/1,5 5-22/xx rpm 0,40/0,8 Yes
Weight without Weight with Hand grip heater Electric carburettor
bar and chain bar and chain Watts/rpm heater
kg/lbs kg/lbs Watts/rpm
570 6,8/14,9 XP18" 8,0kg/17,6 65/10000 Yes
575XP XP 6,8/14,9 XP18" 8,0kg/17,6 65/10000 Yes
XPG 7,0/15,4
rpm
GAS OIL
9. SERVICE TOOLS
English – 9
The tools listed here are service
tools intended for use on the
chainsaw in question. In addition
to these tools, a standard set of
hand tools is required.
14
Item Description Used for Order No.
1 Piston stop Locking the crankshaft 504 91 06-05
2a Cover plate, exhaust Sealing the exhaust port 502 54 11-02
2b Cover plates, inlet kit Sealing the intake system 502 52 48-01
3 Pressure testing device Produce pressure when
leakage testing 531 03 06-23
4 Crankecase splitting tool Dismantling the crankshaft 502 52 49-01
5 Puller Pulling bearing of crankshaft 504 90 90-01
6 Flywheel puller kit Dismantling of the flywheel 502 51 49-02
7 Piston assembly kit Assembling the piston 502 50 70-01
8 Crankshaft assembly tool Assembling the crankshaft 502 50 30-20
9 Seal ring extractor Pulling of seal ring 504 91 40-01
10 Pressure test adapter Pressure testing cylinder 503 84 40-02
11 Feeler gauges ignition gap Air gap tool 502 51 34-02
12 Tachometer Checking engine rpm 502 71 14-01
13 Test spark plug Checking the ignition module 502 71 13-01
14 Clutch tool Dismantling of clutch 502 52 22-01
15 Assembly pliers Assembly of spark plug cap 502 50 06-01
16 Hook for fuel filter Removing fuel filter 502 50 83-01
17 Assembly fixture Assembling chain saw 502 51 02-01
18 Hexagonal screwdriver For M4 screws 502 50 86-01
18 Hexagonal screwdriver For M5 screws 502 50 87-01
18 Hexagonal screwdriver For M6 screws 502 50 88-01
19 Allen key For M4 screws 502 50 19-01
19 Allen key For M5 screws 502 50 18-01
19 Allen key For M6 screws 502 50 64-01
15 16 17
18 19
M4
M5
M6
M4
M5
M6
10. 10 – English
SERVICE DATA
Key to diagrams
The figures next to parts screwed on indicate
the tightening torque Nm.
9Nm 4mm
13Nm 13mm
20Nm 19mm
20Nm 5mm
15Nm 5mm
15Nm 13mm
9Nm 4mm
9Nm 4mm
4.5Nm 4mm
8.5Nm 4mm
1.5Nm
1.5Nm
3.5Nm 4mm
11Nm 5mm
20Nm
5.5Nm 4mm
= Lubricate with two-stroke oil.
= Lubricate with chain oil.
= Lubricate with grease.
12. 12 – English
SAFETY EQUIPMENT
Min. 0.8 mm
WARNING!
Checkthatthebrakeison.Otherwisethe
pressure spring can fly out and cause
personal injury.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Chain brake
Dismantling
1. Dismantle the following parts first:
• Chain and bar. See the Operator's Manual.
2. Push the hand guard forward so that the chain brake
is on. See fig. 1.
3. Remove the chain guide-plate (A). See fig. 1.
4. Remove the four screws (B) and the cover over the
chain brake mechanism. See fig. 1.
!
A
B
C
E
D
F
Fig. 5
A
B
5. Remove the pressure spring by freeing the back end
with a screw driver. See fig. 2.
6. Remove the locking ring (A) with washer (B) and
lift up the clutch drum (E) with needle bearing (D)
and chaindrive sprocket (C). See fig. 3.
7. Remove the hand guard, two screws (A). Note the
sleeve on the starter side. See fig. 4.
8. Remove the toggle joint (E) with attached brake
band. See fig. 5.
Inspection
Clean and inspect all parts.
The thickness of the brake band must nowhere be less
than 0,8 mm. See fig. 5.
A
13. SAFETY EQUIPMENT
English – 13
WARNING!
Ensure that the spring does not fly out
and cause personal injury. Wear pro-
tective glasses.
!
Assembly
Assemble the chain brake as follows:
1. Fit the toggle joint and brake band.
2. Grease the moving parts of the toggle joint (D) and
fit the unit on the chain saw. See fig. 6.
3. Compress the spring using a conical screwdriver
6.5 mm wide and press it down with your thumb.
See fig. 7.
4. Grease and fit the lever (A). See fig. 6.
5. Grease and fit the retaining bush (B) with spring (C).
See fig. 5.
6. Fit the cover over the chain brake mechanism. Four
bolts (B). Tighten the bolts to 4 Nm. See fig. 1.
7. Fit the chain guide-plate with bolt (A). See fig. 1.
8. Fit the hand guard with the sleeve on the starter
side. See fig. 8.
9. Push back the hand guard so that the chain brake
is in the off position.
10.Check that the brake strap is correctly positioned in
the recess in the crankcase. See fig. 9.
11.Grease in the needle bearing before fitting. Fit the
clutch drum (E) with needle bearing (D) and chain
drive sprocket (C). See fig. 3.
12.Fit the washer (B) and locking ring (A). See fig. 3.
13.Fit the cylinder cover, chain and bar. See Operator's
Manual.
Fig. 6
Fig. 9
6.5mm
Fig. 7
Fig. 8
D
A
C B
A
14. 14 – English
SAFETY EQUIPMENT
WARNING!
After repair, the chain brake must be
checked according to the following
instructions.
Bar length, L Height, H
18-32 inches 35 cm
For this test, the engine must not be running.
Check that the chain brake cuts in as follows:
1. Hold the chain saw over a stable surface as shown in
fig. 10.
The distance between the bar and surface is given
in the table below.
2. Let go of the front hand grip and let the chainsaw
pivot round on the rear hand grip.
3. When the bar hits the surface the chain brake
should cut in.
!
Function check
L
L
Fig. 10
L
H
Fig. 11
Chain catcher
There are two types of types of mountings for the chain
catcher fitted on the spike bumper or the crankcase.
Dismantle the chain and bar. See Operator's Manual.
Inspect the chain catcher and replace it if it is damaged.
The bolts should be tightened to 6 Nm. See fig. 11.
Fit the chain and bar. See Operator's Manual.
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. SAFETY EQUIPMENT
English – 15
WARNING!
Do not touch the muffler until it has
cooled. Risk of burn injuries.
!
Fig. 12
Fig. 13
Dismantling
1. Remove the two lower M5 bolts and the mufflerʼs
two M6 bolts. See fig. 12.
2. Remove the gasket and cooling plate. See fig. 12.
3. If the saw is fitted with a spark-arrester, remove it.
See fig. 12.
Inspection
Clean all components and check the following:
1. That the spark-arrester is intact.
2. That the muffler and muffler mounting are not
cracked or otherwise defect.
3. That the gasket is undamaged.
Assembly
1. Clean the contact surfaces to the gasket, cooling
plate and cylinder.
2. If the saw is fitted with a spark-arrester, refit it. See
fig. 12.
3. Fit the cooling plate, gasket and muffler to the
cylinder.
Tighten the two M6 bolts to the cylinder to 14 Nm.
Tighten the four M5 bolts to 10 Nm.
Muffler
Stop switch
Dismantling
The stop switch is in the off position when the switch is
pressed down and in the on position when the switch is
pressed upwards.
Inspection
Measure the resistance by connecting an ohmmeter to
the stop switch. See fig. 13. The resistance should be
as follows:
”0” pressed down - less than 0.1 ohm.
”1” pressed up - more than 1000 ohm.
Assembly
The earth lead is fitted in the upper or lower connection.
See fig. 14.
Fig. 14
A
B
17. 16 – English
SAFETY EQUIPMENT
Throttle lock
Lower the rear of the tank by removing the screws A, B
and C. See fig. 15.
Remove the screw A on hand grip insert. See fig. 16.
Remove the handle insert (A). Remove the guide pin for
the throttle (B) and throttle lock (C) using a punch. See
fig. 17.
Press apart with a screwdriver or the like, the throttle
lock/control and take out the throttle lock from the recess
in the hand grip. See fig. 18.
Now remove the spring.
Fig. 18
Fig. 16
Fig. 17
A
B
C
A
Fig. 15