Gc step 2
•
0 likes•99 views
The document provides instructions for performing a pressure test on a gas analyzer. It instructs the user to select a data set from the main menu, enter any missing port numbers, and ensure the correct calibration gases are selected for the measurement range. It then tells the user to plug the glass bottles into the ports in numerical order without opening them. Finally, it directs the user to select the pressure test option from the main menu, confirm it, and check if the test shows the system is sealed. If not, it advises checking the bottles and vacuum pump valves.
Report
Share
Report
Share
Download to read offline
![Step 2. Pressure test
Schritt 2. Dichtigkeitsprüfung
Main menu (Hauptmenu (1)) select Data set (Messreihe angeben)
(5) Loading
PaulBMBF.P64 [sidenote-- include a (site measured at).P64]
(3) Display table (Tabelle anzeigen)
-Enter in missing port number: with row F3 paste in, type in corresponding port
numbers, and switch it with the next row so the changes are assumed.
- Correctly choose calibration gas in the data set! E0, E1, and E2 for the small/short
measurement range, and E1, E2, E3 for the longer measurement range.
In the correct numerical order according to the protocol, plug the glass bottles in the ports,
but DON’T open them.
In main menu (haupmenü), select (2), Pressure test / dichtigkeitsprüfung.
Press “enter” and affirm it with j.
If it is sealed (it will show Dichtigkeit i.O.), continue to step three.
If the pressure test is not i.O. check the marked bottles on the right side of port, if
necessary separately check the pressure on the vacuum pump of the o.a. valves.
In main menu (haupmenü 2) start a new pressure test.](https://image.slidesharecdn.com/gcstep2-121002090836-phpapp01/85/Gc-step-2-1-320.jpg)
Recommended
Multiple step income statement
TSM Company's multiple-step income statement for the year ended December 2014 shows:
Net sales were calculated by starting with gross sales and subtracting sales returns, allowances, and discounts. Cost of goods sold was calculated by adding opening inventory, purchases, and freight in and subtracting returns, allowances, discounts, and closing inventory. Gross profit was calculated by subtracting cost of goods sold from net sales. Total operating expenses including selling, store salaries, advertising, depreciation, freight out, rent, utilities, and insurance expenses were subtracted from gross profit to get income from operations. Other revenues from interest and gains were added to income from operations and other expenses such as interest and casualty losses were subtracted to
Desarrollados subdesarrollados
El documento contrasta las características de los sectores primario, secundario y terciario entre países desarrollados y subdesarrollados. En los países desarrollados, el sector primario se ha reducido y modernizado, mientras que en los países subdesarrollados depende más de la agricultura de subsistencia. El sector secundario emplea a una menor proporción de la población y depende más de la industria moderna en los países desarrollados, mientras que en los países subdesarrollados predomina la industria artesanal. Final
JE Resume
Joel Epstein is a research associate professor who has received numerous grants to develop technology-based educational programs about drug addiction. He has expertise in curriculum design, program development, outcomes evaluation, and the intersection of technology and behavioral health. Epstein has a PhD in clinical/community psychology and has developed several therapeutic smartphone applications. He has been a research associate professor since 2003 and principal investigator on three grants from the National Institute on Drug Addiction totaling over $2.5 million.
Recommended
Multiple step income statement
TSM Company's multiple-step income statement for the year ended December 2014 shows:
Net sales were calculated by starting with gross sales and subtracting sales returns, allowances, and discounts. Cost of goods sold was calculated by adding opening inventory, purchases, and freight in and subtracting returns, allowances, discounts, and closing inventory. Gross profit was calculated by subtracting cost of goods sold from net sales. Total operating expenses including selling, store salaries, advertising, depreciation, freight out, rent, utilities, and insurance expenses were subtracted from gross profit to get income from operations. Other revenues from interest and gains were added to income from operations and other expenses such as interest and casualty losses were subtracted to
Desarrollados subdesarrollados
El documento contrasta las características de los sectores primario, secundario y terciario entre países desarrollados y subdesarrollados. En los países desarrollados, el sector primario se ha reducido y modernizado, mientras que en los países subdesarrollados depende más de la agricultura de subsistencia. El sector secundario emplea a una menor proporción de la población y depende más de la industria moderna en los países desarrollados, mientras que en los países subdesarrollados predomina la industria artesanal. Final
JE Resume
Joel Epstein is a research associate professor who has received numerous grants to develop technology-based educational programs about drug addiction. He has expertise in curriculum design, program development, outcomes evaluation, and the intersection of technology and behavioral health. Epstein has a PhD in clinical/community psychology and has developed several therapeutic smartphone applications. He has been a research associate professor since 2003 and principal investigator on three grants from the National Institute on Drug Addiction totaling over $2.5 million.
Gc step 2 (1)
The document provides instructions for pressure testing and analyzing gas samples. It first describes how to select a data set and check port numbers and calibration gases for the pressure test. It then explains how to plug bottles into ports without opening them and run the pressure test. Finally, it outlines how to start the analysis, enter a file name, start the analysis by watching the graph, and open bottles if the calibration curve looks correct.
Gc step 2 (1)
The document provides instructions for pressure testing and analyzing gas samples. It first describes how to select the data set and check port numbers and calibration gases. It then instructs to plug bottles into ports without opening them and run a pressure test from the main menu. If the test shows no leaks, proceed to analysis; if leaks are detected, check bottle connections or vacuum pump. It finally outlines how to start analysis by entering a file name in SDDMM_KK format and monitoring the graph to check calibration before opening bottles.
Gc step 2 (1)
The document provides instructions for pressure testing and analyzing gas samples. It first describes how to select a data set and check port numbers and calibration gases for the pressure test. It then explains how to plug bottles into ports without opening them and run the pressure test. Finally, it outlines how to start the analysis, enter a file name, start the analysis while monitoring the graph, and open bottles if the calibration curve looks correct.
Instruction guide for gas phase chromatograph
This instruction guide provides steps for calibrating and using a gas phase chromatograph. It outlines two calibration procedures using different gas concentrations and detector settings. It also describes how to view and adjust the detector baselines and graphs during calibration and analysis. Proper positioning of valves and ensuring the printer has paper are also covered.
Instruction guide for gas phase chromatograph
This instruction guide provides steps for calibrating and using a gas phase chromatograph. It outlines two calibration procedures using different gas concentrations and detector settings. It also describes how to view and adjust the detector baselines and graphs during calibration and analysis. Proper positioning of valves and ensuring the printer has paper are also covered.
Instruction guide for gas phase chromatograph
This instruction guide provides steps for calibrating and using a gas phase chromatograph. It outlines two calibration procedures using different gas concentrations and detector settings. It also describes how to view and adjust the detector curves during calibration and advises plugging bottles into plots after calibration but not opening them.
Instruction guide for gas phase chromatograph
1. The instruction guide provides steps for calibrating a gas phase chromatograph, including preparing the printer and positioning valves between gas bottles and the chromatograph.
2. The main steps are to select the appropriate data set from the main menu depending on the gas concentration and location being tested, and to set the chromatograph control panel accordingly.
3. The guide also provides instructions for performing analysis, accessing gas processor and graphic functions, and correcting baseline curves during calibration using visual references on the chromatograph and monitor.
Instruction guide for gas phase chromatograph
1) Prepare the gas chromatograph by ensuring the paper is loaded properly in the printer and the 3-way valves are positioned correctly between the bottle table and instrument.
2) Perform calibration by selecting the data set menu and inputting the calibration gas concentrations. Set the appropriate detector range based on the gas concentration.
3) Analyze samples by selecting the analysis menu, inputting the data name, selecting the gas processor, and adjusting the detector baselines according to the instrument displays.
Instruction guide for gas phase chromatograph
1) Prepare the gas chromatograph by ensuring the paper is loaded properly in the printer and the 3-way valves are positioned correctly between the bottle table and instrument.
2) Perform calibration by selecting the data set menu and inputting the calibration gas concentrations. Set the appropriate detector range based on the gas concentration.
3) Analyze samples by selecting the analysis menu, inputting the data name, selecting the gas processor, and adjusting the detector baselines according to the instrument displays.
Gc step 2
The document provides instructions for performing a pressure test on a gas measurement system. It instructs the user to select a data set from the main menu, enter any missing port numbers, and ensure the correct calibration gases are selected for the measurement range. It then tells the user to plug glass bottles containing the calibration gases into the ports in numerical order without opening them. Finally, it directs the user to select the pressure test option from the main menu, confirm it, and check if the system is sealed. If not sealed, it advises checking the bottles and vacuum pump valves.
Gc step 2
The document provides instructions for performing a pressure test on a gas measurement system. It instructs the user to select a data set from the main menu, enter any missing port numbers, and ensure the correct calibration gases are selected for the measurement range. It then tells the user to plug glass bottles containing the calibration gases into the ports in numerical order without opening them. Finally, it directs the user to select the pressure test option from the main menu, confirm it, and check if the system is sealed properly. If not sealed, it advises checking the bottles and vacuum pump valves.
More Related Content
Similar to Gc step 2
Gc step 2 (1)
The document provides instructions for pressure testing and analyzing gas samples. It first describes how to select a data set and check port numbers and calibration gases for the pressure test. It then explains how to plug bottles into ports without opening them and run the pressure test. Finally, it outlines how to start the analysis, enter a file name, start the analysis by watching the graph, and open bottles if the calibration curve looks correct.
Gc step 2 (1)
The document provides instructions for pressure testing and analyzing gas samples. It first describes how to select the data set and check port numbers and calibration gases. It then instructs to plug bottles into ports without opening them and run a pressure test from the main menu. If the test shows no leaks, proceed to analysis; if leaks are detected, check bottle connections or vacuum pump. It finally outlines how to start analysis by entering a file name in SDDMM_KK format and monitoring the graph to check calibration before opening bottles.
Gc step 2 (1)
The document provides instructions for pressure testing and analyzing gas samples. It first describes how to select a data set and check port numbers and calibration gases for the pressure test. It then explains how to plug bottles into ports without opening them and run the pressure test. Finally, it outlines how to start the analysis, enter a file name, start the analysis while monitoring the graph, and open bottles if the calibration curve looks correct.
Instruction guide for gas phase chromatograph
This instruction guide provides steps for calibrating and using a gas phase chromatograph. It outlines two calibration procedures using different gas concentrations and detector settings. It also describes how to view and adjust the detector baselines and graphs during calibration and analysis. Proper positioning of valves and ensuring the printer has paper are also covered.
Instruction guide for gas phase chromatograph
This instruction guide provides steps for calibrating and using a gas phase chromatograph. It outlines two calibration procedures using different gas concentrations and detector settings. It also describes how to view and adjust the detector baselines and graphs during calibration and analysis. Proper positioning of valves and ensuring the printer has paper are also covered.
Instruction guide for gas phase chromatograph
This instruction guide provides steps for calibrating and using a gas phase chromatograph. It outlines two calibration procedures using different gas concentrations and detector settings. It also describes how to view and adjust the detector curves during calibration and advises plugging bottles into plots after calibration but not opening them.
Instruction guide for gas phase chromatograph
1. The instruction guide provides steps for calibrating a gas phase chromatograph, including preparing the printer and positioning valves between gas bottles and the chromatograph.
2. The main steps are to select the appropriate data set from the main menu depending on the gas concentration and location being tested, and to set the chromatograph control panel accordingly.
3. The guide also provides instructions for performing analysis, accessing gas processor and graphic functions, and correcting baseline curves during calibration using visual references on the chromatograph and monitor.
Instruction guide for gas phase chromatograph
1) Prepare the gas chromatograph by ensuring the paper is loaded properly in the printer and the 3-way valves are positioned correctly between the bottle table and instrument.
2) Perform calibration by selecting the data set menu and inputting the calibration gas concentrations. Set the appropriate detector range based on the gas concentration.
3) Analyze samples by selecting the analysis menu, inputting the data name, selecting the gas processor, and adjusting the detector baselines according to the instrument displays.
Instruction guide for gas phase chromatograph
1) Prepare the gas chromatograph by ensuring the paper is loaded properly in the printer and the 3-way valves are positioned correctly between the bottle table and instrument.
2) Perform calibration by selecting the data set menu and inputting the calibration gas concentrations. Set the appropriate detector range based on the gas concentration.
3) Analyze samples by selecting the analysis menu, inputting the data name, selecting the gas processor, and adjusting the detector baselines according to the instrument displays.
Similar to Gc step 2 (9)
More from Rodrigo Rudge
Gc step 2
The document provides instructions for performing a pressure test on a gas measurement system. It instructs the user to select a data set from the main menu, enter any missing port numbers, and ensure the correct calibration gases are selected for the measurement range. It then tells the user to plug glass bottles containing the calibration gases into the ports in numerical order without opening them. Finally, it directs the user to select the pressure test option from the main menu, confirm it, and check if the system is sealed. If not sealed, it advises checking the bottles and vacuum pump valves.
Gc step 2
The document provides instructions for performing a pressure test on a gas measurement system. It instructs the user to select a data set from the main menu, enter any missing port numbers, and ensure the correct calibration gases are selected for the measurement range. It then tells the user to plug glass bottles containing the calibration gases into the ports in numerical order without opening them. Finally, it directs the user to select the pressure test option from the main menu, confirm it, and check if the system is sealed properly. If not sealed, it advises checking the bottles and vacuum pump valves.
More from Rodrigo Rudge (7)
Gc step 2
- 1. Step 2. Pressure test Schritt 2. Dichtigkeitsprüfung Main menu (Hauptmenu (1)) select Data set (Messreihe angeben) (5) Loading PaulBMBF.P64 [sidenote-- include a (site measured at).P64] (3) Display table (Tabelle anzeigen) -Enter in missing port number: with row F3 paste in, type in corresponding port numbers, and switch it with the next row so the changes are assumed. - Correctly choose calibration gas in the data set! E0, E1, and E2 for the small/short measurement range, and E1, E2, E3 for the longer measurement range. In the correct numerical order according to the protocol, plug the glass bottles in the ports, but DON’T open them. In main menu (haupmenü), select (2), Pressure test / dichtigkeitsprüfung. Press “enter” and affirm it with j. If it is sealed (it will show Dichtigkeit i.O.), continue to step three. If the pressure test is not i.O. check the marked bottles on the right side of port, if necessary separately check the pressure on the vacuum pump of the o.a. valves. In main menu (haupmenü 2) start a new pressure test.