This document is a maintenance manual for the GPC2000 Series. It provides safety information and procedures for maintenance, repair, and testing of components. The manual contains sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, and electrical diagrams. Safety must be followed when working on the truck including following all applicable regulations and only allowing qualified personnel to perform repairs.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
10. 3
3
MP/MS-0000-MA
SAFETY
MS-GPC2000-GB 04/02 • Rev. A • Printed in Germany
REV. 1 4/00
OPTION
Safety Symbols used in the
Manual
To help guide you through the manual and to highlight
particular danger areas, we have used graphic illustra-
tions:
DANGER
This symbol indicates life-threatening risks
● Failure to comply with this notice may
result in severe or fatal injuries to yourself
or other people.
WARNING
This symbol indicates the risk of serious
injury and/or serious material damage.
● Failure to comply with this notice may
result in severe injuries to yourself or other
people and/or serious material damage.
CAUTION
This symbol indicates the risk of minor
injury and/or minor material damage.
● Failure to comply with this notice may
result in minor injuries to yourself or other
people and/or minor material damage.
INFORMATION
Contains additional information with
supplementary notes and hints.
OPTION
These items relate to optional features not
supplied with the standard version.
General Maintenance and Repair
Safety Notes
DANGER
Read the safety notices in the truck Mainte-
nance and Operator's Manuals.
● Failure to do so could result in severe or
fatal injuries to maintenance personnel
and/or other persons.
Motorised vehicles can be dangerous if maintenance
and service are neglected. For this reason maintenance
and inspections must be carried out at regular short
intervals by trained personnel working to approved
company guidelines.
DANGER
Follow all national/local safety regulations
applicable for maintenance work, e.g. for
work on higher levels.
● Failure to do so could result in severe or
fatal injuries to maintenance personnel and/
or other persons.
Maintenance and Repair
1. Maintenance work must only be carried out in
accordance with the test and maintenance pro-
gram contained in the present Maintenance
Manual and any applicable service notices.
2. Only qualified and authorised personnel may
carry out work on the truck.
3. Always keep fire extinguishers in good working
condition. Do not approach fluid levels or leaks
with a naked flame.
4. To clean, use a non flammable, non combustible
cleaning solution which is groundwater-neutral.
Only carry out cleaning with an oil separator.
Protect the electrical system from dampness.
5. Keep the service area clean, dry and well-venti-
lated.
6. Do not allow oil to penetrate the ground or enter
the draining system. Used oil must be recycled.
Oil filters and desiccants must be treated as
special waste products. Relevant applicable
regulations must be followed.
7. Neutralise and thoroughly rinse any spilled battery
fluid immediately.
11. 4
4
MP/MS-0000-MA
SAFETY
MS-GPC2000-GB 4/02 • Rev. A • Printed in Germany
REV. 1 4/00
8. Keep the truck clean. This will facilitate the loca-
tion of loose or faulty components.
9. Make sure that capacity and data plates, warnings
and labels are legible at all times.
10. Alterations or modifications by the owner or
operator are not permitted without the express
written authorisation from Crown.
11. Only use original Crown spare parts to ensure the
reliability, safety and suitability of the Crown truck.
Before Leaving the Truck
● Stop the truck.
● Lower the fork carriage fully.
● Apply the parking brake.
● Turn off the travel switch and remove the key.
● Block all wheels when parking on an uneven
surface.
Before Carrying out Work on the Truck
● Raise the truck to free the drive wheel. Press the
emergency Stop button and disconnect the
battery.
● Prevent the truck from rolling away.
● Before carrying out work on the hoist frame, the
lift mast or on the fork carriage: Block these parts
according to maintenance instructions in order to
prevent them from dropping.
● Only carry out operational testing when there is
sufficient room to manoeuvre, to avoid the risk of
injury to yourself and others.
Before Operating the Truck
● Check the safety devices.
● Get into the driver's seat.
● Check the operation of the lifting device, travel
direction switch, speed control, steering, warning
devices and brakes.
Warnings and Labels on the Truck
During regular maintenance check that the warnings
and labels on the truck are complete and legible.
● Clean any illegible labels.
● Replace any faulty or missing labels.
The order and meaning of the warnings and labels on
the truck are described in section 10.9 of the parts
manual.
13. 7
M1.0-0000-0007
7
INTRODUCTION
MS-GPC2000-GB 04/02 • Rev. A • Printed in Germany MS-ITD-6620
series. Brochures can be obtained from your CROWN
dealer or from the following address:
CROWN Gabelstapler GmbH
Moosacher Str. 52
80809 Munich
GERMANY
Tel.: +49 (0)89 / 93 002 -0
Fax: +49 (0)89 / 93 002 -175 oder 133
Using the Manual
The manual is divided into sections. The following table
shows how the manual is structured.
A01M-gb
General
The present manual is designed for Customer Service
engineers who wish to familiarise themselves with the
maintenance work required for the various truck compo-
nents.
It also contains troubleshooting sections which can be
used to identify and remedy truck faults.
INFORMATION
This book is not an operating manual. It is
designed solely for specialist personnel
who have been trained and authorised to
carry out the work described in the manual.
This manual therefore contains fewer and less detailed
warnings than the Operator's Manual, as the latter is aimed
at persons who have very little or no prior experience at
all.
Operating Instructions
This manual contains no operating instructions. An
operating instructions manual is supplied with the vehicle.
Additional copies can be ordered as required.
With the help of this manual you and your personnel will
be able to ensure the long service life, operational safety
and error free functioning of your CROWN vehicle.
Service Training
CROWN offers the appropriate vehicle related training for
service personnel. Details on this training can be obtained
from CROWN on request.
Ordering Spare Parts
The maintenance manual does not cover spare parts.The-
se are listed in a separate manual.
Spare parts can be ordered by quoting:
● The truck specification number
● The truck model number
● The truck serial number
This information can be found on the truck's data plate.
Only if this information is provided can the order be
processed quickly, correctly and reliably.
Please refer to the Technical Specifications Sheet for the
utilisable loads, technical data and dimensions for this
e
c
n
a
n
e
t
n
i
a
M
s
n
o
i
t
c
e
S
n
o
i
t
c
e
S n
o
i
t
p
i
r
c
s
e
D
X
D
I t
n
e
t
n
o
C
f
o
e
l
b
a
T
A
M y
t
e
f
a
S
D
T
I
-
S
M n
o
i
t
c
u
d
o
r
t
n
I
1
-
S
M t
n
e
m
t
s
u
j
d
A
d
n
a
n
o
i
t
a
c
i
r
b
u
L
2
-
S
M s
c
i
l
u
a
r
d
y
H
3
-
S
M t
i
n
U
e
v
i
r
D
4
-
S
M l
a
c
i
r
t
c
e
l
E
5
-
S
M e
k
a
r
B
6
-
S
M g
n
i
r
e
e
t
S
7
-
S
M m
s
i
n
a
h
c
e
M
g
n
i
t
f
i
L
/
t
s
a
M
8
-
S
M r
e
d
n
i
l
y
C
A
I
D s
m
a
r
g
a
i
D
l
a
c
i
r
t
c
e
l
E
D
Y
H c
i
t
a
m
e
h
c
S
c
i
l
u
a
r
d
y
H
14. 8
M1.0-0000-0008
8
INTRODUCTION
MS-GPC2000-GB 04/02 • Rev. A • Printed in Germany
MS-ITD-6620
Modeldescription
Low Level Order Picker, 1.600 kg capacity
GPC2020
Modeldescription
Low Level Order Picker, 2.000 kg capacity
GPC2040
Modeldescription
Rider Pallet Truck with Steering Wheel, 2.000 kg capacity
GPC2040S
Model-Number
This manual describes the maintenance and repairs for the following truck versions:
16. 11
LUBRICATION AND ADJUSTMENT
MS-GPC2000-GB 04/02 • Rev. A • Printed in Germany
1B
377
192
583
1
2
1
2
3
3
4
MS-6620-003
A
MS-6620-004
MS-1.0-6620
Jacking up the Truck
CAUTION
Always support a raised truck with wooden
blocks or other suitable equipment, thereby
relieving the jack.
The instruction "jack up the truck" always assumes that
the raised truck will be lowered onto a secure surface.
To jack up the truck, proceed as follows (Picture MS-
6620-003):
● Lift the forks to maximum height.
● Secure both loadwheels with a wedge (1).
● Apply a jack with sufficient capacity (> 900 kg) at
the middle of the chassis frame and raise the
truck (2).
● Place sufficiently sized woodenblocks (hard
wood)
on both sides underneath the chassis and lower
the truck onto the blocks (3).
● Apply the jack to the forks.
● Place a wooden block under the forks and lower
the truck onto it (4).
Fastening
screws
If there is sufficient distance between the truck centre of
gravity (e.g. 1B) and the rear end of the chassis frame
the truck can be supported by placing a block under the
rear end of the chassis frame (instead of the forks) -
point A in figure above. In this case, place an extra
wooden block under the tips of the lowered fork.
Lifting the Truck with a Crane
DANGER
Make sure the capacity of the crane and the
lifting device is sufficient. If a crane or truck
tips or a load falls, fatal injuries can result.
For lifting the truck, the forks must be in a raised posi-
tion (maximum height).
In order to attach the lifting straps to the truck at the
locations indicated, you must first tilt back the battery
compartment cover and remove the side panels.
Attach the straps (ropes, chains) to the hitch points as
shown in.
Required lifting capacity: 730 kg for a GPC with
1000 mm forks, 870 kg for a GPC with 2880 mm forks
(GPC without battery).
17. M1.0-0000-00012
M1.0-0000-00012
12
LUBRICATION AND ADJUSTMENT
MS-GPC2000-GB 04/02 • Rev. A • Printed in Germany
>
800
> 600
1B
377
192
583
1
120
2
MS-6620-003
MS-1.0-6620
Lifting the Truck with a second
Truck
The GPC can be lifted by another truck from the side.
Required lifting capacity: 730 kg for a GPC with
1000 mm forks, 870 kg for a GPC with 2880 mm forks
(GPC without battery).
● Place the forks of the truck which is doing the
lifting under the GPC chassis as indicated by the
black forks under the GPC in the figure below.
Exception: GPC with fork length over
2000 mm and without battery. Position the forks
of the truck which is doing the lifting as indicated
by the grey forks under the GPC in the figure
below. The forks of the GPC must be in their
uppermost position. Insert a 120 mm thick block
between the forks of the GPC and the corre-
sponding fork of the lifting truck.
● Firmly secure the GPC to the forks of the truck
which is doing the lifting (e.g with appropriate
straps).
Position of the truck’s centre of gravity
1B 1000 mm forks, with 385 kg battery
1 1000 mm forks, without battery
2 2880 mm forks, without battery
Rear fork of the truck which is doing the lifting
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 13
LUBRICATION AND ADJUSTMENT
MS-GPC2000-GB 04/02 • Rev. A • Printed in Germany
100 mm
400
mm
MS-1.0-6620
Towing the Truck
If the truck is without power supply, the brake is applied
to the drive wheel. The truck can be partially lifted and
moved by another truck with a lifting capacity of
1300 kg or more (GPC without load, with 385 kg battery
and 2880 mm fork length). The load wheels remain on
the floor during the procedure.
● Position the fork under the chassis as shown.
● Lift the truck (at the front part) approximately 20
mm off the floor.
CAUTION
The drive wheel must be lifted from the
floor! Otherwise the truck could be dam-
aged.
● Pull the truck slowly straight forward (as indicated
by the black arrow).
Load Wheels
20. M1.0-0000-00014
M1.0-0000-00014
14
LUBRICATION AND ADJUSTMENT
MS-GPC2000-GB 04/02 • Rev. A • Printed in Germany
MS-1.0-6620
De-commissioning
If the truck is to be out of service for 3 months or more,
proceed as follows:
● Disconnect the battery.
● De-commission the battery in accordance with the
manufacturer‘s instructions.
● Clean the truck*). Carry out lubrication in accord-
ance with the Maintenance Manual.
● When storing in adverse environmental conditions
(e.g. saline atmosphere), take appropriate meas-
ures to cover the truck to prevent corrosion.
● Jack up the truck, lower the chassis onto suitable
wooden blocks to clear the wheels from the
ground to prevent the wheels from flattening
under constant pressure.
● Every 3 months, connect the battery, carry out the
daily inspection and operate all the truck func-
tions. Finally, disconnect the battery again.
Re-commissioning
To re-commission the truck, proceed as follows:
● Remove any anti-corrosion film that may have
been applied*).
● Jack up the truck, remove the wooden blocks,
lower the truck.
● Charge the battery or install a charged battery.
● Connect the battery.
● Carry out the daily inspection.
*) Do not use pressure jets and/or solvents with the
truck! Do not use metal brushes!