This document provides specifications for Iveco "NEF" diesel engines, including 3 and 4 cylinder atmospheric and turbocharged models. It describes the engines' lubrication and cooling systems, dimensions of components like pistons and cylinders, and torque specifications. The document states that the performance data is only valid if the installer follows Iveco's recommendations, and that any equipment added by the installer must respect the engine's designed power and rpm limits.

1. A3.2 Nectis 207 – 12.2005 – GB
General specification
103vfm00 Fig. 1
"NEF" engines are 3 or 4 cylinder diesel units with
2 valves per cylinder, and may be atmospheric or
turbo-charged. They are equipped with mechanical rotary
injection pumps.
N.B.: The data, characteristics and outputs are only
valid if the installer observes the relevant Iveco
installation recommendations. Any equipment fitted
by the installer must also always respect the torque
and power outputs and rpm figures for which the
engine was designed.

2. A3.4 Nectis 207 – 12.2005 – GB
General specification
3 cylinder engines
Type
CE0304 Atmospheric F4CE0354 Turbo-charged
B*D6.. A*D6.. C*D6..
Compression ratio 17,5: 1
Maximum power *
Maximum torque *
Rated speed (rpm) *
Tick-over speed *
Maximum no-load engine rpm *
• Lubrication
Oil pressure, hot engine:
Supplied by a lobe pump, via a pressure limiting valve and oil filter
– At minimum rpm (bar). 1,2
– At maximum rpm (bar). 3,8
• Cooling Liquid
Water pump drive: Belt driven
Thermostat:
– Starts opening at (°C). 81 ± 2
Lubricant*
• Capacity (litres)
– Engine sump
* Refer to the user manual.
*
bar

3. Nectis 207 – 12.2005 – GB A3.5
General specification
Type
CE0304 Atmospheric F4CE0354 Turbo-charged
B*D6.. A*D6.. C*D6..
Number of cylinders 3
Bore (mm) 104
Stroke (mm) 132
Overall capacity (cm³) 3 364
Ω
+ + + ... =

4. A3.6 Nectis 207 – 12.2005 – GB
General specification
4 cylinder engines
Type
F4CE0404
Atmospheric
F4CE0454
Turbo-charged
A*D6.. A*D6.. C*D6..
Compression ratio 17,5: 1
Maximum power *
Maximum torque *
Rated speed *
Tick-over speed *
Maximum no-load engine rpm *
• Lubrication
Oil pressure, hot engine:
Supplied by a lobe pump, via a pressure limiting valve and oil filter
– At minimum rpm (bar). 1,2
– At maximum rpm (bar). 3,8
• Cooling Liquid
Water pump drive: Belt driven
Thermostat:
– Starts opening at (°C). 81 ± 2
Lubricant*
• Capacity (litres)
– Engine sump
* Refer to the user manual.
*
bar

5. Nectis 207 – 12.2005 – GB A3.7
General specification
The data, characteristics and outputs are only valid if
the installer observes the relevant Iveco installation
recommendations.
Any equipment fitted by the installer must also
always respect the torque and power outputs and rpm
figures for which the engine was designed.
Type
F4CE0404 F4CE0454
A*D6.. A*D6.. C*D6..
Number of cylinders 4
Bore (mm) 104
Stroke (mm) 132
Overall capacity (cm³) 4 485
Ω
+ + + ... =

6. A3.8 Nectis 207 – 12.2005 – GB
Lubrication
Operation
The pressurised lubrication system uses a lobe oil pump
located at the front of the block, driven by the splined ring
attached to the crankshaft cone. Oil is pumped from the
crankcase to the crankshaft, the camshaft and the
cylinder head (oil cooler, turbocharger).
Oil system layout (3-cylinder engine)
221vfm00 Fig. 3
Nomenclature
177 Turbocharger oil return line.
178 Oil filter.
179 Oil cooler element.
180 Oil cooler.
181 Oil pump.
Oil pressure feed.
Oil gravity return route.
177
178
179
180
181

7. Nectis 207 – 12.2005 – GB A3.9
Lubrication
Oil system layout (4-cylinder engine)
221vfm01 Fig. 4
Nomenclature
182 Turbocharger oil return line.
183 Oil filter.
184 Oil cooler element.
185 Oil cooler.
186 Oil pump.
Oil pressure feed.
Oil gravity return route.
182
183
184
186
185

8. A3.10 Nectis 207 – 12.2005 – GB
Cooling
Operation
The pressurised closed circuit engine cooling system has
the following components:
• Expansion tank.
• Radiator, to dissipate the heat extracted from the
engine by the coolant fluid.
• Visco-static cooling fan to increase the radiator's heat
dissipation capability, that also forms part of the engine's
specific build.
– An oil cooler to cool the lubricant oil
– A centrifugal-type water pump located at the front of the
engine block.
– A thermostat that controls the circulation of the coolant
fluid.
Cooling (3-cylinder engine)
251vfm05 Fig. 5
Nomenclature
A Radiator inlet.
B Radiator outlet.
Coolant leaving the thermostat.
Coolant recirculating within the engine.
Coolant entering the water pump.
A
B

9. Nectis 207 – 12.2005 – GB A3.11
Cooling
Cooling system (4-cylinder engine)
251vfm06 Fig. 6
Nomenclature
A Radiator inlet.
B Radiator outlet.
Coolant leaving the thermostat.
Coolant recirculating within the engine.
Coolant entering the water pump.
A
B

10. A3.12 Nectis 207 – 12.2005 – GB
Turbocharger
Operation
Turbo-charged version of the engine
167vfm00 Fig. 7
The air intake system consists of an air filter and an
exhaust-driven compressor (turbocharger).
Air from the compressor outlet is fed directly to the inlet
manifold.
Nomenclature
4 Exhaust.
209 Air filter.
210 Turbocharger. A 3 cylinder version.
B 4 cylinder version.
210
4
210
209
209
A
B
4

11. Nectis 207 – 12.2005 – GB A3.13
DIMENSIONS
Dimensions - build clearances
Type Atmospheric Turbo-charged
Engine block and components of the crank drive mechanism (mm)
Cylinder
Cylinder liner diameter 1
(machined)
104,000 – 104,024
Piston
Supplied replacement
pistons:
Measured dimension (X) 52,4 55,9
External diameter (ø 1) 103,755 – 103,773 103,730 – 103,748
Gudgeon pin bore (ø 2) 38,010 – 38,016 38,010 – 38,016
Piston - Cylinder liner
clearance
0,227 – 0,269 0,252 – 0,294
Piston diameter (ø 1)
(repair size)
Ø1 + 0,4
Piston overtravel height (X) 0,28 – 0,52
Gudgeon pins (ø 3) 37,994 – 38,000
Gudgeon pin clearance in
piston
0,010 – 0,022
Piston ring grooves
X1*
X2
X3
* Measure across the 101 mm diameter.
2,600 – 2,620
2,550 – 2,570
4,030 – 4,050
2,705 – 2,735*
2,440 – 2,460
4,030 – 4,050
Rings
S1
S2
S3
2,470 – 2,500
2,478 – 2,490
3,970 – 3,990
2,560 – 2,605
2,350 – 2,380
3,970 – 3,990
Ring clearance - groove
1
2
3
0,100 – 0,150
0,060 – 0,092
0,040 – 0,080
0,100 – 0,175
0,060 – 0,110
0,040 – 0,080
Rings + 0,4
ø 1
X
ø 1
X
ø 2
X
ø 3
X2
X1
X3
S1
S3
S2

12. A3.14 Nectis 207 – 12.2005 – GB
DIMENSIONS
Type Atmospheric Turbo-charged
Engine block and crank assembly (mm)
Piston ring gap in cylinder
liner:
X1
X2
X3
0,25 – 0,55
0,30 – 0,55
0,30 – 0,55
0,30 – 0,40
0,60 – 0,80
0,30 – 0,55
Connecting rod
Bush housing in small end (ø
1)
40,987 – 41,013
Big-end bearing shell housing
(ø 2)
72,987 – 73,013
Small end bush dimensions
External (ø 4)
Internal (ø 3)
40,987 – 41,013
38,019 – 38,033
Replacement big-end bearing
shells supplied (S)
1,955 – 1,968
Gudgeon pin clearance - bush 0,019 – 0,039
Big-end bearing shells
(repair size)
0,250 – 0,500
Crankshaft
Main journals (ø 1) 82,990 – 83,010
Big-end journals (ø 2) 68,987 – 69,013
X1
X2
X3
ø 1
ø 2
S
ø 4
ø 3
ø 1 ø 2

13. Nectis 207 – 12.2005 – GB A3.15
DIMENSIONS
Type Atmospheric Turbo-charged
Engine block and crank assembly (mm)
Crankshaft main bearing
shells (S1)
2,456 – 2,464
Big-end bearing shells (S2) 1,955 – 1,968
Engine block
Main bearing
N° 1 - 4 (ø 3)
N° 2 - 3 (ø 3)
87,982 – 88,008
87,977 – 88,013
Set of bearing shells - main
bearing
N° 1 - 4
N° 2 - 3
0,064 – 0,095
0,059 – 0,100
Set of big-end bearing shells 0,033 – 0,041
Main bearing shells (repair
size)
Big-end bearing shells (repair
size)
+ 0,250 ; + 0,500
Main bearing with thrust
shoulder (X1)
37,475 – 37,550
Main bearing with thrust
shoulder (X2)
31,730 – 32,280
Thrust bearing shells (X3) 37,28 – 37,38
Crankshaft thrust bearing end
float
0,095 – 0,270
S1 S2
ø 3
X1
X2
X3

14. A3.16 Nectis 207 – 12.2005 – GB
DIMENSIONS
Type Atmospheric Turbo-charged
Cylinder head - valvegear (mm)
Valve
Valve guide housings in
cylinder head
See detail under "valves"
Valves: See detail under "valves"
Clearance between valve
stem and valve guide
0,039 – 0,079
Valve head recess below
cylinder head face
Intake (X)
0,336 – 1,072
Exhaust (X)
0,104 – 0,840
X

15. Nectis 207 – 12.2005 – GB A3.17
DIMENSIONS
Type Atmospheric Turbo-charged
Cylinder head - valvegear (mm)
Valve spring height
Spring unloaded: H 63,50
Spring under a load of:
32,9 daN (H1) 49,02
64,1 daN (H2) 38,20
Injector
Injector protrusion (X) Not adjustable
Camshaft
Camshaft bearing housings:
– Rear bearing diameter C
(3-cylinder engine).
– Rear bearing diameter C
and front bearing diameter A
(4-cylinder engine).
59,222 – 59,248
Camshaft bearing housings:
– 2 intermediate bearings
diameter B and front bearing
diameter A
(3-cylinder engine).
– 3 intermediate bearings
diameter B
(4-cylinder engine).
54,089 – 54,139
Camshaft bearings:
ø 53,995 – 54,045
Bearing internal diameter (ø) 54,083 – 54,147
H H1
H2
X
ø A ø B ø C
ø
ø

16. A3.18 Nectis 207 – 12.2005 – GB
DIMENSIONS
Type Atmospheric Turbo-charged
Cylinder head - valvegear (mm)
Clearance between bearings
and camshaft
0,038 – 0,152
Clearance between bearings
and engine block
0,044 – 0,144
Effective valve lift:
Exhaust (H) 11,02
Intake (H) 10,74
Cam followers
Cam follower housing in
block (ø 1)
16,000 – 16,030
Cam follower external
diameter:
Ø2 15,929 – 15,959
Ø3 15,965 – 15,980
Clearance between cam
follower and housing
0,020 – 0,065
Rockers
Rocker shaft (ø 1) 18,963 – 18,975
Rockers (ø 2) 19,000 – 19,026
Clearance between rockers
and rocker shaft
0,025 – 0,063
Adjusting the valve rockers
Inlet valves x (mm) 0,25 ± 0,05
Exhaust valves x (mm) 0,50 ± 0,05
H
ø 1
ø 2
14 32 50
ø 2
ø 3
ø 1
ø 2
X

17. Nectis 207 – 12.2005 – GB A3.19
DIMENSIONS
Valves
Inlet and exhaust valve dimensions (in mm).
Nomenclature
1 Exhaust valve.
2 Intake valve.
131vfm00 Fig. 8
Valve guide/seat dimensions
Nomenclature
3 Intake.
4 Exhaust.
131vfm09 Fig. 9
44,75
45,25
7,960
7,980
7,960
7,980
59,75
60,25
42,13
41,87
45,13
44,87
1 2
43
8,019
8,039

18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

19. A3.20 Nectis 207 – 12.2005 – GB
DIMENSIONS
Valve seat housing dimensions
131vfm11 Fig. 10
Dimensions (mm) of valve seat inserts
131vfm12 Fig. 11
Nomenclature
3 Intake.
4 Exhaust.
34
3,460
3,200
10,400
10,000
1,980
1,580
50,5˚
49,5˚
50,5˚
49,5˚
3,470
10,600˚
10,200˚
1,810
1,550
ø 50,000
ø 47,000
ø 44,400
ø 47,013
ø 46,987
ø 43,663
ø 43,637
34
43,739
43,713
47,089
47,063
ø 42,500ø 39,500
6,516
6,440
45,5˚
44,5˚
60,5˚
59,5˚
6,804
6,728

20. Nectis 207 – 12.2005 – GB A3.21
Torque settings
Front chassis / engine link
A. 39 daN.m (4 M20 nuts).
Engine/transmission link
B. 8 daN.m + Frenetanch (242)
(4 screws HM12x125-65).
C. Locating pin.
D. 8 daN.m + Frenetanch (242)
(8 screws HM12x175-50).
103vfm02 Fig. 12
103vfm03 Fig. 13
AA
B
C
D D
B
C
D D

21. A3.22 Nectis 207 – 12.2005 – GB
Torque settings
101vfm00 Fig. 14
16
23
18
19
20
9
26
1
29
10
32
7
33
25
6
13
11
12
30
31
27
28
35
34
8
4
1422
15
3
2
21
24
17
5