1. This document provides instructions for removing the complete engine from an AXION 800 A61 tractor with a serial number range of A6100100 to present. 2. It details disconnecting various components such as hoses, wiring harnesses, and hydraulic lines to fully separate the engine from the tractor. 3. Special tools are required to lift and support the engine during removal, including engine lifting brackets and a flywheel rotating tool. Proper lifting procedures should be followed due to the engine's 920kg weight.

1. AXION 870-850-830-810
CMATIC
Repair manual
Original repair manual
1/1Couverture RHB AXION 870-810 CMATIC (A61)
2020/3/27http://localhost:8081/webtic/app/Module/2292/1/en/0/210183/001/EN/Target0

2. Validity of this repair manual
This repair manual applies to the following tractor:
Description Type
Tractor serial number
From to
AXION 800 A61 A6100100 —
1/1Validité de ce manuel de réparation
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/2.1.2/210191/001/EN/T...

3. Complete engine
Technical specifications
Number Value Note – Description
1 920 kg Complete engine
For unspecified tightening torques, refer to the section entitled: "Tightening torques".
WARNING
Lifting heavy components.
Risk of death or serious injury.
► Use certified slings or chains in perfect working order.
► Use a certified hoist in perfect working order.
► Use a certified jack or stand which can support the load.
► Use the jack or stand on a flat, horizontal, sufficiently firm surface.
► Place the jack or stand in a suitable location.
NOTICE
Lubricants and fuels end up in the environment.
Environmental pollution
► Collect and store lubricants and fuels in suitable containers and dispose of them properly.
1/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

4. Special tool
Special tool – Reference no.
Carriage to be uncoupled
No. 00 1148 105 0
Special tool – Reference no.
Extension
No. 00 1148 106 0
2/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

5. Special tool – Reference no.
1
Engine lifting brackets kit
No. 00 1152 870 0
Component parts of the NEF 6 kit
2
Bracket at the front of the engine
No. 1149 878 1/1
3
Bracket at the right-hand side of the engine
No. 1149 878 1/2D
4
Bracket at the left-hand side of the engine
No. 1149 878 1/2G
3/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

6. Special tool – Reference no.
Flywheel rotating tool
No. 00 1150 142 0
Removal
► Drain the engine.
► Drain the air conditioning circuit.
► Drain the pneumatic brake circuit (optional).
► Drain the cooling circuit.
► Remove the engine bonnet.
Engine bonnet
.
► Remove the left-hand tank.
Main tankFunction:01 Engine
.
► Remove the exhaust gas post-treatment system. .
4/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

7. ► Remove bolts (1) and (2) and (6).
► Remove the protective panel (3).
► Disconnect the electric starting motor wiring harnesses (4).
► Remove the electric starting motor (5).
► Remove the bolts (1).
► Move aside the protective panel (2).
5/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

8. ► Remove the clamp (1).
► Remove the bolt (2) from the mounting clamp.
► Remove the coolant hose (3).
► Remove the mounting clamps (1), (2) and (3).
► Mark and remove the rigid pipe connectors.
6/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

9. ► Remove the clamps (1).
► Loosen the flexible pipe connector (2).
► Undo connectors (1) and (2).
► Remove the clamp (3).
► Remove the clamps (4), (5), (6) and remove the hoses (7), (8) and (9).
7/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

10. ► Remove the clamp (1).
► Remove the connector (2) and the bolt (3).
► Remove the air conditioning pipes (4) and (5).
Seal the openings of the air conditioning compressor. Attach the pipes to the cabin.
8/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

11. ► Mark and disconnect the electrical wiring harness (1) of the engine.
► Mark and disconnect the electrical wiring harness (2) of the front linkage.
► Mark and disconnect the electrical wiring harness (3) of the front axle.
► Remove the bolts (1).
► Remove the tank mounting panel (2).
9/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

12. ► Decompress the front axle suspension circuit by acting on the suspended front axle hydraulic block (1).
Decompressing the CARRARO front axle suspension hydraulic circuit
► Remove the clamps (2).
► Undo the flexible pipe connector (1).
► Remove the clamps (2).
► Undo the pipe connectors (1).
10/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

13. ► Uncouple the pipes (2), (3) and (4).
► Remove the bolts (1) from the front axle hydraulic block support.
► Remove the suspended front axle hydraulic block.
► Remove the clamps (1), (2), (3) and (4).
► Uncouple the hydraulic connectors.
► Uncouple the air connectors (5) and (6) (optional).
► Remove the bolts (7) and (8) from the air regulator support (optional).
► Remove the air regulator (9) (optional).
11/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

14. ► Remove the clamps (1).
► Mark and uncouple the hydraulic connectors (2).
► Remove the pipes (3).
► Remove the nuts (1) and (2) from the transmission shaft protective panel.
► Remove the transmission shaft protective panel (3).
12/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

15. ► Remove the bolts (1) and (2) from the transmission shaft.
► Remove the transmission shaft (3).
► Remove the bolts (1) and (2).
► Remove the clamps (3), (4), (5) and (9).
► Uncouple the pipes (6), (7) and (8).
13/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

16. ► Disconnect the connector (10).
► Remove the hose (6).
► Remove the clamps (4) and (5).
► Remove the hose (3).
► Remove the bolts (2).
► Remove the expansion bottle assembly and its support (1).
14/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

17. ► Remove the clamp (4).
► Remove the clamps (3).
► Remove the hoses (1) and (2).
► Remove the connectors (1) and (2).
► Remove the bolt (3) from the support bracket.
► Remove the pipes (4) and (5).
► Remove the bolt (1).
► Remove the wiring harness (2) of the "Visctronic" "C080" fan.
15/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

19. ► Remove the bolts and nuts (2).
► Remove the turbocharger protective panel (1).
► Remove the bolts (1).
► Remove the nuts (2).
► Remove the subframe (1) with a suitable lifting tool.
16/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN

20. The support weighs 36 kg.
► Remove the nuts (1).
► Remove the apron (2).
► Remove the coolant pipe (1) located at the rear of the cylinder head.
► Undo the nut (1) of the visco coupler.
17/41Moteur complet
2020/3/27http://localhost:8081/webtic/app/Module/2292/001/en/4.1.1/162371/006/EN