2. Crankshaft bearing seals
Technical specifications
Number Value Note – Description
1 — Crankshaft front bearing seal
2 — Crankshaft rear bearing seal
For unspecified tightening torques, refer to the section entitled: "Tightening torques".
Environment!
Lubricants and fuel are harmful to the environment.
Pollution
► Collect lubricants and fuel in appropriate containers; store and dispose of them in accordance with the
regulations in force.
Special tool
1/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
3. Special tool (I) – Reference no.
Tool for removing the rear bearing seal
N o. 00 1130 887 0
2/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
4. Special tool (II) – Reference no.
Tool for fitting the rear bearing seal
N o. 00 1130 889 0
Special tool (III) – Reference no.
Tool for removing the front bearing seal
N o. 00 1130 886 0
3/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
5. Special tool (IV) – Reference no.
Tool for fitting the front bearing seal
N o. 00 1130 888 0
Removing the crankshaft rear bearing seal
► Drain the engine oil.
► Uncouple the engine from the transmission.
4/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
6. ► Remove the transport damper (1).
Transport damper
► Remove the engine flywheel (2).
Flywheel
► Remove the centring pin (1).
► Position the special tool (I) on the seal.
To make it easier to fit the bolts of the special tool, make a hole of 3.5 mm (1) at a depth of 5 mm in
the inner ring of the seal.
5/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
7. ► Remove the inner section of the seal using the special tool (I).
► Remove the outer section of the seal using a slide hammer.
Fitting the crankshaft rear bearing seal
► Fit the crankshaft seal using the special tool (II).
Replace the centring pin if it is damaged.
► Fit the centring pin (1).
6/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
8. ► Fit the engine flywheel (2).
Flywheel
► Fit the transport damper (1).
Transport damper
► Couple the engine to the transmission.
Chassis-engine-gearbox coupling
► Fill the engine with oil.
► Perform an operating check.
Removing the crankshaft front bearing seal
► Drain the engine oil.
► Remove the pulley assembly (1)
Crankshaft pulleyFunction:01 Engine
7/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
9. ► Remove the centring pin (1) for mounting the special tool (III).
► Position the special tool (III) on the seal.
To make it easier to fit the bolts of the special tool, make a hole of 3.5 mm (1) at a depth of 5 mm in
the inner ring of the seal.
► Remove the inner section of the seal using the special tool (III).
► Remove the outer section of the seal using a slide hammer.
8/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
10. Fitting the crankshaft front bearing seal
► Fit the crankshaft seal using the special tool (IV).
Replace the centring pin if it is damaged.
► Fit the centring pin (1).
► Fit the pulley assembly (1).
Crankshaft pulleyFunction:01 Engine
9/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
11. ► Fill the engine with oil.
► Perform an operating check.
10/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
12. Crankshaft bearing seals
Technical specifications
Number Value Note – Description
1 — Crankshaft front bearing seal
2 — Crankshaft rear bearing seal
For unspecified tightening torques, refer to the section entitled: "Tightening torques".
Environment!
Lubricants and fuel are harmful to the environment.
Pollution
► Collect lubricants and fuel in appropriate containers; store and dispose of them in accordance with the
regulations in force.
Special tool
1/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
13. Special tool (I) – Reference no.
Tool for removing the rear bearing seal
N o. 00 1130 887 0
2/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
14. Special tool (II) – Reference no.
Tool for fitting the rear bearing seal
N o. 00 1130 889 0
Special tool (III) – Reference no.
Tool for removing the front bearing seal
N o. 00 1130 886 0
3/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
15. Special tool (IV) – Reference no.
Tool for fitting the front bearing seal
N o. 00 1130 888 0
Removing the crankshaft rear bearing seal
► Drain the engine oil.
► Uncouple the engine from the transmission.
4/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
16. ► Remove the transport damper (1).
Transport damper
► Remove the engine flywheel (2).
Flywheel
► Remove the centring pin (1).
► Position the special tool (I) on the seal.
To make it easier to fit the bolts of the special tool, make a hole of 3.5 mm (1) at a depth of 5 mm in
the inner ring of the seal.
5/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. ► Remove the inner section of the seal using the special tool (I).
► Remove the outer section of the seal using a slide hammer.
Fitting the crankshaft rear bearing seal
► Fit the crankshaft seal using the special tool (II).
Replace the centring pin if it is damaged.
► Fit the centring pin (1).
6/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
19. ► Fit the engine flywheel (2).
Flywheel
► Fit the transport damper (1).
Transport damper
► Couple the engine to the transmission.
Chassis-engine-gearbox coupling
► Fill the engine with oil.
► Perform an operating check.
Removing the crankshaft front bearing seal
► Drain the engine oil.
► Remove the pulley assembly (1)
Crankshaft pulleyFunction:01 Engine
7/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...
20. ► Remove the centring pin (1) for mounting the special tool (III).
► Position the special tool (III) on the seal.
To make it easier to fit the bolts of the special tool, make a hole of 3.5 mm (1) at a depth of 5 mm in
the inner ring of the seal.
► Remove the inner section of the seal using the special tool (III).
► Remove the outer section of the seal using a slide hammer.
8/10Joints de paliers du vilebrequin
2020/3/27http://localhost:8081/webtic/app/Module/1095/003/en/4.3.5/164659/003/EN/T...