1) The document provides assembly and disassembly instructions for a gear motor and control valve used in a wheeled excavator.
2) The gear motor assembly instructions include installing bearings, seals, gears, and housing components in 12 steps.
3) The control valve disassembly instructions describe removing 33 parts in 12 steps, taking care with springs that could cause injury.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5. Illustration 7 g01172343
8. Install seal (7) and seal (8) .
Illustration 8 g01172342
9. Install bearing (6) .
Illustration 9 g01172341
10. Install O-ring seal (5) .
4/5(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 10 g01172340
11. Install O-ring seal (3) and housing (4) .
Illustration 11 g01172339
12. Install head (2) and bolts (1). Tighten bolts (1) to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
End By: Install the gear motor. Refer to Disassembly and Assembly, "Gear Motor (Hydraulic
Generator) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 13:00:00 UTC+0800 2020
5/5(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C MH WHEELED EXCAVATOR BEB
Configuration: M318C Material Handler BEB00001-02000 (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M318C and M322C Excavators Machine Systems
Media Number -RENR9213-02 Publication Date -01/12/2006 Date Updated -05/12/2006
i02370432
Gear Motor (Hydraulic Generator) - Install
SMCS - 5061-012
Installation Procedure
Illustration 1 g01182780
1. Install key (8) .
1/3(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 2 g01182778
2. Install hub (6), lockwasher (7), and nut (5). Tighten nut (5) to a torque of 80 ± 20 N·m (59 ±
15 lb ft).
Illustration 3 g01182776
3. Install coupling (4) .
2/3(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 4 g01182829
4. Position gear motor (1) and install bolts (2). Connect hose assemblies (3) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 13:00:57 UTC+0800 2020
3/3(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C MH WHEELED EXCAVATOR BEB
Configuration: M318C Material Handler BEB00001-02000 (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M318C and M322C Excavators Machine Systems
Media Number -RENR9213-02 Publication Date -01/12/2006 Date Updated -05/12/2006
i02370509
Control Valve (Hydraulic Generator) - Remove
SMCS - 5051-011
Removal Procedure
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
At operating temperature, the hydraulic oil is hot and under pressure.
Hot oils can cause burns.
To prevent possible personal injury, release the pressure in the work
tool hydraulic circuit (boom, stick, bucket, and swing), travel circuits,
and the hydraulic oil tank at the filler cap before any hydraulic lines or
components are disconnected or removed.
Remove the filler cap only when the engine is stopped and the filler cap
is cool enough to touch.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
Illustration 1 g01182843
2/3(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 1. Disconnect hose assemblies (4) and harness assembly (3) .
2. Remove bolts (2). Use two people to remove control valve (1). The weight of control valve
(1) is approximately 34 kg (75 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 13:01:53 UTC+0800 2020
3/3(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C MH WHEELED EXCAVATOR BEB
Configuration: M318C Material Handler BEB00001-02000 (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M318C and M322C Excavators Machine Systems
Media Number -RENR9213-02 Publication Date -01/12/2006 Date Updated -05/12/2006
i02388710
Control Valve (Hydraulic Generator) - Disassemble
SMCS - 5051-015
Disassembly Procedure
Start By:
A. Remove the control valve (hydraulic generator). Refer to Disassembly and Assembly,
"Control Valve (Hydraulic Generator) - Remove".
Illustration 1 g01192533
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
1/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (1) and actuator (2) .
Illustration 2 g01192535
2. Remove solenoid valve (3), spring (6), and O-ring seals (4) and (5) .
Illustration 3 g01192536
3. Remove retainer (10), spool (9), plug (8), and makeup valve (7) .
2/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 4 g01192537
4. Remove backup ring (11) and O-ring seals (12) from makeup valve (7) .
Illustration 5 g01192538
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Remove plugs (13) and (14) .
3/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 6 g01192539
6. Remove spring (15) and O-ring seal (16) from plug (13) .
Illustration 7 g01192540
7. Remove spring (17) and O-ring seal (18) from plug (14) .
Illustration 8 g01192542
8. Remove spool (20) and nut (19) .
4/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 9 g01192543
9. Remove cartridge (21). Remove plugs (22), (23), and (24) .
Illustration 10 g01192544
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove bolts (26), plate assembly (25), and O-ring seal (27) .
5/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 11 g01192547
11. Remove spring (28) and plug (29) .
Illustration 12 g01192548
Illustration 13 g01192549
6/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove plug (30), cone (31), spring (32), and O-ring seal (33) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 13:02:49 UTC+0800 2020
7/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C MH WHEELED EXCAVATOR BEB
Configuration: M318C Material Handler BEB00001-02000 (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M318C and M322C Excavators Machine Systems
Media Number -RENR9213-02 Publication Date -01/12/2006 Date Updated -05/12/2006
i02388711
Control Valve (Hydraulic Generator) - Assemble
SMCS - 5051-016
Assembly Procedure
Illustration 1 g01192549
1/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 2 g01192548
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install O-ring seal (33), spring (32), cone (31), and plug (30). Tighten plug (30) to a torque
of 120 N·m (89 lb ft).
Illustration 3 g01192547
2. Install spring (28) and plug (29). Tighten plug (29) to a torque of 200 N·m (148 lb ft).
Illustration 4 g01192544
2/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
3. Install plate assembly (25), O-ring seal (27), and bolts (26). Tighten bolts (26) to a torque of
10.4 N·m (92 lb in).
Illustration 5 g01192543
4. Install cartridge (21). Install plugs (22), (23), and (24). Tighten plug (22) to a torque of 60
N·m (44 lb ft). Tighten plug (23) to a torque of 45 N·m (33 lb ft). Tighten plug (24) to a
torque of 80 N·m (59 lb ft).
Illustration 6 g01192542
3/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. 5. Install spool (20) and nut (19). Tighten nut (19) to a torque of 80 N·m (59 lb ft).
Illustration 7 g01192539
6. Install spring (15) and O-ring seal (16) to plug (13) .
Illustration 8 g01192540
7. Install spring (17) and O-ring seal (18) to plug (14) .
4/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 9 g01192538
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8. Install plugs (13) and (14). Tighten plug (13) to a torque of 80 N·m (59 lb ft). Tighten plug
(14) to a torque of 90 N·m (66 lb ft).
Illustration 10 g01192537
9. Install backup ring (11) and O-ring seals (12) to makeup valve (7) .
Illustration 11 g01192536
5/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. 10. Install retainer (10), spool (9), plug (8), and makeup valve (7). Tighten makeup valve (7) to
a torque of 100 N·m (74 lb ft). Tighten plug (8) to a torque of 45 N·m (33 lb ft).
Illustration 12 g01192535
11. Install solenoid valve (3), spring (6), and O-ring seals (4) and (5). Tighten solenoid valve (3)
to a torque of 12 ± 5 N·m (106 ± 44 lb in).
Illustration 13 g01192533
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
12. Install actuator (2) and bolts (1). Tighten bolts (1) to a torque of 10.4 N·m (92 lb in).
6/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. End By: Install the control valve (hydraulic generator). Refer to Disassembly and Assembly,
"Control Valve (Hydraulic Generator) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Apr 10 13:03:45 UTC+0800 2020
7/7(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C MH WHEELED EXCAVATOR BEB
Configuration: M318C Material Handler BEB00001-02000 (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M318C and M322C Excavators Machine Systems
Media Number -RENR9213-02 Publication Date -01/12/2006 Date Updated -05/12/2006
i02370510
Control Valve (Hydraulic Generator) - Install
SMCS - 5051-012
Installation Procedure
Illustration 1 g01182843
1. Use two people to position control valve (1). The weight of control valve (1) is
approximately 34 kg (75 lb). Install bolts (2) .
2. Connect hose assemblies (4) and harness assembly (3) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Fri Apr 10 13:04:43 UTC+0800 2020
1/2(W)
w
2020/4/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...