Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR FB4
Configuration: M314F Wheeled Excavator FB400001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
M314F, M316F, M318F, M320F and M322F Wheeled Excavator Power Train
Media Number -UENR6143-07 Publication Date -01/03/2018 Date Updated -13/03/2018
i06214408
Axle - Remove and Install - Rear Axle
SMCS - 3278-010; 3282-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 380-5719 Hydraulic Jack 1
Start By:
a. Remove the travel motor.
b. Remove the rear tires and rims.
1. Drain the oil from the rear axle into a suitable container for storage or disposal. Refer to
Operation and Maintenance Manual, "Axle Oil (Rear) - Change".
Illustration 1 g01175091
1/4(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 4 g01316583
4. Position Tooling (A) below transmission (3).
5. Disconnect hose assembly (6).
6. Attach a suitable lifting device to rear axle (4). The weight of rear axle (4) and transmission
(3) is approximately 794 kg (1750 lb).
7. Remove nuts (5) and carefully remove rear axle (4) and transmission (3) from the machine.
Illustration 5 g01316587
3/4(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 8. Attach a suitable lifting device to transmission (3). The weight of transmission (3) is
approximately 136 kg (300 lb).
9. Remove bolts (7) and transmission (3).
Installation Procedure
1. Install rear axle (4) in the reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 29 10:15:48 UTC+0800 2020
4/4(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR FB4
Configuration: M314F Wheeled Excavator FB400001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
M314F, M316F, M318F, M320F and M322F Wheeled Excavator Power Train
Media Number -UENR6143-07 Publication Date -01/03/2018 Date Updated -13/03/2018
i06215027
Axle - Disassemble - Front Axle
SMCS - 3278-015; 3282-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8T-0980 Bearing Extractor 1
8T-0504 Bearing Puller 1
1P-0510 Driver Gp 1
B 8T-0984 Holder 1
C 1U-7600 Slide Hammer Puller Gp 1
D
8T-0979 Puller Gp 1
1U-5816 Sleeve 1
E 1U-7502 Repair Stand 1
Start By:
a. Remove the front axle.
b. Remove the final drive carriers, the hubs, and the brakes.
c. Remove the steering housing and bearings.
1/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 1 g01135670
1. Attach a suitable lifting device to the front axle assembly and position the front axle
assembly onto Tooling (E). The weight of the front axle assembly is approximately 213 kg
(470 lb).
2. Remove bolts (2).
3. Attach a suitable lifting device to axle housing (1) and remove axle housing (1). The weight
of axle housing (1) is approximately 68 kg (150 lb).
Illustration 2 g01135682
4. Remove differential (3) from axle housing (4).
2/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 3 g01008032
5. Install Tooling (A) in order to remove bearing cone (5) (not shown).
Illustration 4 g01008033
6. Install Tooling (A) in order to remove bearing cone (6) (not shown).
Illustration 5 g01008034
7. Remove bolts (7) from differential (3).
Illustration 6 g01008036
3/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 8. Remove case (8) from differential (3).
Illustration 7 g01008037
9. Remove thrust washer (9) and side gear (10).
Illustration 8 g01008035
10. Remove spider assembly (11), thrust washer (12), and spider gears (13).
Illustration 9 g01008038
11. Remove side gear (14) and thrust washer (15) (not shown).
4/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 10 g01008039
12. Use a suitable press in order to remove differential case (16) from ring gear (17).
Illustration 11 g01135689
13. Install Tooling (B) to flange (19). Remove nut (18).
Illustration 12 g01138045
14. Remove washer (20) and flange (19).
5/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 13 g01135702
15. Use Tooling (C) in order to remove shaft seal (21).
Illustration 14 g01008565
16. Remove pinion assembly (22).
Illustration 15 g01135703
17. Remove bearing cone (23).
6/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 16 g01008567
Illustration 17 g01008568
18. Remove spacing ring (24).
19. Install Tooling (D) in order to remove bearing cone (25).
Illustration 18 g01135705
20. Remove bearing cup (26) and bearing cup (27) from axle housing (4).
7/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 19 g01135711
21. Remove bearing cup (28) and shim (28A) (not shown) from axle housing (4).
Illustration 20 g01135719
22. Remove bearing cup (29) and O-ring seal (30) from the axle housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Apr 29 10:16:44 UTC+0800 2020
8/8(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR FB4
Configuration: M314F Wheeled Excavator FB400001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
M314F, M316F, M318F, M320F and M322F Wheeled Excavator Power Train
Media Number -UENR6143-07 Publication Date -01/03/2018 Date Updated -13/03/2018
i06215059
Axle - Assemble - Front Axle
SMCS - 3278-016; 3282-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 8T-0984 Holder 1
E 1U-7502 Repair Stand 1
F 6V-2012 Depth Micrometer 1
G
8T-0986 Bearing Installer Gp 1
126-7183 Crossblock 1
H 123-6698 Measuring Ring 1
J 6V-7059 Micrometer 1
K
8T-0976 Measuring Tool 1
1U-5824 Centering Ring 1
L 123-6702 Backlash Gauge Gp 1
M 8T-5096 Dial Indicator Gp 1
N 9S-7354 Torque Wrench Gp 1
1/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 1 g01135853
Illustration 2 g01135855
1. Subtract the Dimension that is stamped on pinion assembly (22) from the Dimension that is
stamped on axle assembly (4). The difference is Dimension (A).
Illustration 3 g01135856
2. Use a Tooling (F) to measure the thickness of bearing cup (26) and bearing cone (23).
Record this Dimension as Dimension (B).
3. Subtract Dimension (B) from Dimension (A). The difference is Value (C). Value (C) is the
thickness of the shims that are needed for the correct pinion depth.
2/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 4 g01135858
Illustration 5 g01135861
4. Lower the temperature of bearing cup (27) and bearing cup (26).
Note: The shims are installed behind bearing cup (27).
5. Install the amount of shims that were determined in Steps 1 through 3 into axle housing (4).
6. Use Tooling (G) to install bearing cup (27) into axle housing (4).
7. Install bearing cup (26).
3/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 6 g01018522
8. Raise the temperature of bearing cone (25). Lower the temperature of pinion assembly (22).
9. Install bearing cone (25) onto pinion assembly (22).
Illustration 7 g01135868
10. Install Tooling (H) onto pinion assembly (22).
4/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 8 g01135870
11. Install pinion assembly (22) into axle housing (4).
12. Raise the temperature of bearing cone (23). Install bearing cone (23) onto pinion assembly
(22).
Illustration 9 g01135877
13. Install flange (19). Install washer (20) and nut (18).
14. Install Tooling (B) onto flange (19).
Illustration 10 g01135891
Note: During the tightening of nut (18), make several full revolutions of pinion assembly
(22) in both directions.
15. Use Tooling (N) to tighten nut (18) until a rolling torque between 1 N·m (9 lb in) and 2 N·m
(18 lb in) is obtained.
5/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 11 g01135877
16. Remove Tooling (B). Remove nut (18), washer (20), and flange (19).
Illustration 12 g01135927
17. Remove bearing cone (23) and pinion assembly (22) from axle housing (4).
Illustration 13 g01135868
6/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 18. Remove Tooling (H).
Illustration 14 g01135934
19. Use Tooling (J) to measure the thickness of Tooling (H). Record this Dimension as
Dimension (D). Dimension (D) is the thickness that is required for spacer ring (24) in Step
20.
Illustration 15 g01018582
20. Install spacer ring (24) onto pinion assembly (22).
7/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 16 g01135927
21. Install pinion assembly (22) into axle housing (4).
22. Raise the temperature of bearing cone (23). Install bearing cone (23) onto pinion assembly
(22).
Illustration 17 g01135877
23. Install flange (19). Install washer (20) and nut (18). Install Tooling (B). Tighten nut (18) to
a torque of 430 N·m (317 lb ft). Remove Tooling (B).
8/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 18 g01135891
24. If necessary, change the thickness of the spacer ring that was installed during Step 20 in
order to achieve a rolling torque between 1 N·m (9 lb in) and 2 N·m (18 lb in). Use Tooling
(N) in order to check the rolling torque.
Illustration 19 g01135877
25. Install Tooling (B). Remove nut (18), washer (20), flange (19), and Tooling (B).
9/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 20 g01135935
26. Install shaft seal (21).
Illustration 21 g01135877
27. Install flange (19). Install washer (20) and nut (18). Install Tooling (B). Tighten nut (18) to
a torque of 430 N·m (317 lb ft).
28. Remove Tooling (B) from flange (19).
Illustration 22 g01018596
29. Lower the temperature of differential case (16). Raise the temperature of ring gear (17).
30. Install ring gear (17) onto differential case (16).
10/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 23 g01018597
31. Install thrust washer (15) and side gear (14).
Illustration 24 g01018899
Note: The tabs of the thrust washers (12) must be installed in the upward position.
32. Install spider gears (13), thrust washers (12), and spider assembly (11).
Illustration 25 g01018900
33. Install side gear (10) and thrust washer (9).
11/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 26 g01018901
34. Install case (8) onto differential (3).
Illustration 27 g01018902
35. Install bolts (7) into differential (3). Tighten bolts (7) to a torque of 145 N·m (107 lb ft).
Illustration 28 g01018903
36. Raise the temperature of bearing cone (6) and bearing cone (5).
37. Install bearing cone (6) and bearing cone (5).
12/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 29 g01018904
38. Install shim (28A) (not shown) and bearing cup (28) into axle housing (4).
Illustration 30 g01135958
39. Install bearing cup (29) into Tooling (K).
Illustration 31 g01135961
40. Install differential (3) into axle housing (4).
13/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Illustration 32 g01135969
41. Install Tooling (K) onto differential (3) and axle housing (4).
Note: During the adjustment of Tooling (K), make several full revolutions of pinion
assembly (22) in both directions.
42. Adjust Tooling (K) until differential (3) is free of play and free of pressure. Tighten the lock
bolt.
Illustration 33 g01135979
43. Install Tooling (L) to the bore of the differential shaft.
44. Install Tooling (M) onto Tooling (K) and Tooling (L) in order to measure the backlash. The
correct backlash is between 0.15 mm (0.006 inch) and 0.25 mm (0.010 inch).
45. Change the thickness of shim (28A) from Step 38 in order to correct the backlash.
Note: Do not loosen the lock bolt on Tooling (K). Remove Tooling (K) and bearing cup
(29) as a unit.
46. Remove Tooling (M) and Tooling (L). Remove Tooling (K) and bearing cup (29) as a unit.
14/22(W)
w
2020/4/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...