The document provides instructions for removing the front housing on a C4.4 engine. Key steps include:
1. Removing various external components like the fan, pulley, oil pan, and gears.
2. Disconnecting electrical and coolant components from the front housing.
3. Removing several bolts of different lengths that secure the front housing to the engine block.
4. Removing the front housing and gasket from the engine block. Proper identification of removed parts is important for reinstallation.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
The document provides instructions for removing and installing the idler gear on a C4.4 engine. There are separate procedures for a standard idler gear and a heavy-duty idler gear. The removal procedure involves locking the camshaft and crankshaft, removing mounting bolts, and tilting the gear out of position. The installation procedure involves cleaning and inspecting parts, aligning timing marks, lubricating components, and checking specifications such as end play and backlash. Tools and torque specifications are provided.
Caterpillar cat m318 d wheeled excavator (prefix w8p) service repair manual (...fdjjsekksemxs
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 diesel engine. It describes:
1) The required tools and preparation steps, which include locking the camshaft and crankshaft, removing covers, and ensuring the valves are closed.
2) The removal procedure, which involves marking components, loosening rocker arms, and tilting the idler gear during removal.
3) The installation procedure, such as cleaning parts, aligning timing marks, and lubricating before sliding the hub into the idler gear. Precise timing of the camshaft and crankshaft is required.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
The document provides instructions for removing the idler gear from a Caterpillar C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump gear in position using timing pins to maintain proper timing.
2. Removing the idler gear plate bolts and plate, then removing the idler gear and hub assembly.
3. Inspecting the removed parts for wear or damage and replacing as needed.
This document provides instructions for removing and installing the idler gear on a Caterpillar C4.4 engine. The removal process involves locking the camshaft and crankshaft, loosening rocker arm adjusters, and removing bolts and plates to access the idler gear. Installation requires aligning timing marks, checking components for wear, lubricating, and torquing bolts to specified values. End play and backlash are checked using feeler gauges or dial indicators to ensure proper specifications are met.
This document provides instructions for removing and installing an idler gear on a Caterpillar 320D2 GC excavator engine. The removal procedure involves locking the camshaft and crankshaft, loosening rocker arm adjusters, and removing bolts and plates to access the idler gear. The installation procedure specifies cleaning and inspecting parts, aligning timing marks, installing with bolts and checking backlash and end play using tools like feeler gauges. The document contains illustrations to supplement the text instructions.
This document provides instructions for removing and installing the idler gear on a Caterpillar C4.4 engine. The removal procedure involves locking the camshaft and crankshaft, loosening the rocker arms, and removing bolts and plates to access the idler gear. The installation procedure specifies cleaning and inspecting parts, aligning timing marks, checking clearances with tools, and torquing bolts to specifications. Proper lubrication and positioning of identification marks are also emphasized.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
The document provides instructions for removing and installing the idler gear on a C4.4 engine. There are separate procedures for a standard idler gear and a heavy-duty idler gear. The removal procedure involves locking the camshaft and crankshaft, removing mounting bolts, and tilting the gear out of position. The installation procedure involves cleaning and inspecting parts, aligning timing marks, lubricating components, and checking specifications such as end play and backlash. Tools and torque specifications are provided.
Caterpillar cat m318 d wheeled excavator (prefix w8p) service repair manual (...fdjjsekksemxs
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 diesel engine. It describes:
1) The required tools and preparation steps, which include locking the camshaft and crankshaft, removing covers, and ensuring the valves are closed.
2) The removal procedure, which involves marking components, loosening rocker arms, and tilting the idler gear during removal.
3) The installation procedure, such as cleaning parts, aligning timing marks, and lubricating before sliding the hub into the idler gear. Precise timing of the camshaft and crankshaft is required.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
The document provides instructions for removing the idler gear from a Caterpillar C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump gear in position using timing pins to maintain proper timing.
2. Removing the idler gear plate bolts and plate, then removing the idler gear and hub assembly.
3. Inspecting the removed parts for wear or damage and replacing as needed.
This document provides instructions for removing and installing the idler gear on a Caterpillar C4.4 engine. The removal process involves locking the camshaft and crankshaft, loosening rocker arm adjusters, and removing bolts and plates to access the idler gear. Installation requires aligning timing marks, checking components for wear, lubricating, and torquing bolts to specified values. End play and backlash are checked using feeler gauges or dial indicators to ensure proper specifications are met.
This document provides instructions for removing and installing an idler gear on a Caterpillar 320D2 GC excavator engine. The removal procedure involves locking the camshaft and crankshaft, loosening rocker arm adjusters, and removing bolts and plates to access the idler gear. The installation procedure specifies cleaning and inspecting parts, aligning timing marks, installing with bolts and checking backlash and end play using tools like feeler gauges. The document contains illustrations to supplement the text instructions.
This document provides instructions for removing and installing the idler gear on a Caterpillar C4.4 engine. The removal procedure involves locking the camshaft and crankshaft, loosening the rocker arms, and removing bolts and plates to access the idler gear. The installation procedure specifies cleaning and inspecting parts, aligning timing marks, checking clearances with tools, and torquing bolts to specifications. Proper lubrication and positioning of identification marks are also emphasized.
New holland t5.120 electro command tractor service repair manualfusjejfskekemm
This service manual provides maintenance and repair instructions for T5.100, T5.110, and T5.120 Electro Command tractors. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader, accessories, platform and bodywork. Safety precautions are provided throughout.
New holland t5.110 electro command tractor service repair manualfusjejfskekemm
This service manual provides maintenance and repair instructions for T5.100, T5.110, and T5.120 Electro Command tractors. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader, accessories, and the platform, cab, bodywork and decals. Safety precautions are provided throughout.
New holland t4.85 n tractor service repair manualfusjejfskekemm
This document is a service manual for tractor models T4.75N, T4.85N, T4.95N, T4.105N, T4.65V, T4.75V, T4.85V, T4.95V, and T4.105V. It contains information on engine service, clutch service, transmission service, four-wheel drive systems, front and rear axle systems, power take-off systems, brake systems, and hydraulic systems for these tractor models. The manual is intended to guide service technicians in maintenance, repair, and troubleshooting of components.
New holland l218, l220 tier 4 b (final) skid steer loader service repair manu...fusjejfskekemm
This document is a service manual for New Holland L218 and L220 skid steer loaders that meet Tier 4B emission standards. It contains sections covering the engine, cooling system, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, cab climate control, electrical systems, front loader and bucket, and the platform, cab, bodywork, and decals. Safety information is provided at the beginning regarding servicing the equipment and personal safety precautions.
New holland l170 skid steer service repair manualfusjejfskekemm
This document provides the table of contents for the repair manual for L160 and L170 skid steers. It lists 15 sections that are included in the manual, such as the engine, rear drive axle, brakes, and electrical system. The document focuses on Section 10 for the engine, outlining chapters on general engine information, removal and disassembly, maintenance of engine components, reassembly, installation back into the skid steer frame, and operation of the cooling system. The repair manual contains detailed instructions and specifications to service and repair the engine and other systems.
New holland b80 b backhoe loader service repair manualfusjejfskekemm
This document is a service manual for a Case backhoe loader that contains instructions for servicing and maintaining various systems of the machine, including the engine, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, electrical systems, front loader, booms, dippers, buckets, accessories, and bodywork. It provides part numbers and safety information to technicians servicing the equipment.
This document is a service manual for liquid-cooled horizontal crankshaft engines models LH630, LH685, LH750, and LH760. It contains 11 sections covering safety, troubleshooting, various engine systems, disassembly, inspection, and reassembly. Section 1 provides important safety information, including warnings about rotating parts, hot parts, accidental starts, carbon monoxide, electrical shock, hot liquids, explosive gases, flammable solvents, and recommendations for proper oil, coolant, and fuel types.
Hyster j006 (h6.0 ft europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing and repairing various components of a lift truck, including:
- Side covers, floor plates, seats, dashes, and hoods. Removal and installation steps are provided.
- Counterweights, mufflers, overhead guards, engines, exhaust systems, and LPG fuel tanks. Procedures for checks, repairs, and safety label installation are included.
- Frames, fuel tanks, hydraulic tanks, and counterweight mounts. Component descriptions and identification are given.
- Operator restraint systems including seat belts and hip restraints. Inspection and functionality checks are outlined.
- Hood support assemblies, hood doors, pre-cleaners, and related components
Hyster g019 (h16.00 xm 6 europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing various components of a lift truck, including removing and installing the air cleaner, exhaust system, hood assembly, and hydraulic tank. Key steps include draining fluids, disconnecting hoses and electrical connections, removing mounting hardware, and lifting components away from the frame with caution. Proper identification of removed parts and reinstallation in reverse order is emphasized.
Hyster g005 (h4.00 xl 5) forklift service repair manualfusjejfskekemm
The document provides information about repairing gear pumps. It describes the components and operation of single-stage and tandem gear pumps. The key steps for repair include removal, disassembly, cleaning, inspection, and reassembly. Worn or damaged seals are a common cause of pump failure. The seals can be replaced, but if other components like gears or bearings are worn, a new pump may be more cost effective than repair. Careful documentation of part locations and orientations is important during disassembly and reassembly.
Hyster g004 (s80 ftbcs) forklift service repair manualfusjejfskekemm
This document provides repair procedures for manual and electronic main control valves used in hydraulic lift trucks. There are two main types of control valves - manual and electro-hydraulic. The electro-hydraulic valve uses electronics to control lift, lower, tilt and auxiliary functions. It also has an emergency manual lowering valve. The document describes removing the control valve which involves disconnecting hydraulic hoses and electrical connectors, removing mounting bolts, and removing O-rings between valve sections.
Hyster f006 (h7.00 xl) forklift service repair manualfusjejfskekemm
This document provides a description and repair procedures for the steering axle assembly on various lift truck models. It describes the components of the steering axle including the axle frame, steering cylinder, tie rods, and spindle and hub assemblies. It explains that the steering axle is articulated and connected to the frame with center pivot mounts. The document then provides detailed removal and installation instructions for the steering axle on different lift truck models.
Hyster f005 (h3.50 xl) forklift service repair manualfusjejfskekemm
The document provides instructions for repairing the speed reducer and differential assembly of a lift truck. It includes descriptions of the components, removal and disassembly steps, cleaning and inspection guidelines, and assembly procedures. Some key points:
- The speed reducer and differential are housed together, with the speed reducer transferring power between the transmission and differential gears.
- To repair, the entire drive axle assembly is removed from the lift truck as a unit. It is then disassembled by removing components like the axle shafts, speed reducer housing, ring and pinion gears, and bearings.
- Parts are cleaned and inspected for wear or damage before assembly. Assembly involves installing bearings and gears back into their
Hyster d007 (h190 xl) forklift service repair manualfusjejfskekemm
The document provides repair procedures for a differential. It describes removing and disassembling the differential from the axle housing. Procedures are given for adjusting the pinion bearings and carrier shims to set the pinion depth correctly when installing a new pinion and ring gear set. The ring gear is heated and installed on the differential case half. The case halves are then assembled along with the other differential components and lubricated before installation.
Hyster c114 (ej1.25 xl europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing the brake system on certain electric lift truck models. It describes the components and operation of the master cylinder and wheel cylinders. The repair procedures for the master cylinder and brakes on the EJ1.25-1.75XL models are then outlined in detail, including removal, disassembly, inspection, cleaning, and reassembly of the parts. Diagrams are included to illustrate the components and proper assembly. Safety warnings are provided throughout regarding handling of brake components and fluids.
New holland w300 c wheel loader service repair manualfusjejfskekemm
This service manual provides instructions for servicing a Wheel Loader model W270C-W300C. It contains sections covering general information, engines, fuel systems, electrical systems, steering, powertrains, brakes, hydraulics, mounted equipment, and schematics. The document provides section indexes listing topics and their corresponding section numbers for easy navigation. It also includes standard torque specifications for hardware, fluids and lubricants information, and a metric conversion chart.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfusjejfskekemm
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies that are planetary gear units to increase torque to the drive wheels.
2) It provides an overview of the main components - axle shafts, sun gears, planetary pinions, planetary gear carriers, ring gears, and differentials. Service and parking brakes are also installed.
3) The operation section explains how the differential rotation causes the axle shafts and sun gears to rotate, turning the planetary pinions which rotate the planetary spiders and drive wheels, while the ring gear and hub do not rotate.
Hyster a917 (h40.00 xm 12 europe) forklift service repair manualfusjejfskekemm
This document provides descriptions and repair procedures for differentials. It describes the typical components of a differential assembly, including the housing, ring and pinion gear set, and differential assembly. The repair procedures cover removing the differential carrier from the axle housing, removing the differential and ring gear from the carrier, and removing the drive pinion and pinion carrier from the carrier. Detailed steps are provided for disassembling the differential and ring gear assembly and disassembling the drive pinion and pinion carrier.
Hyster a236 (h450 hd) forklift service repair manualfusjejfskekemm
This document provides repair procedures for differentials used in H400HD, H400HDS, H450HD, and H450HDS lift trucks. It describes the components of a typical differential assembly and provides step-by-step instructions for removing the differential carrier from the axle housing, removing the differential and ring gear from the carrier, and removing the drive pinion and pinion carrier. It also gives directions for disassembling the differential and ring gear assembly. Specifications and troubleshooting information are provided at the end.
Hyster a217 (n30 fr) forklift service repair manualfusjejfskekemm
This document provides specifications for various parts and lift capacities for the N30FR, N40EA/ER, N40FR, N45ER, N45FR, N50EA, and N50FA lift truck models. Some key details include:
- The basic lift capacities for each model at a 24 inch and 500mm load center.
- Battery specifications like voltage, compartment size, and battery size/weight for each model.
- Hydraulic system specifications like pump output, relief valve pressures, and tank capacities.
- Reach carriage specifications like stroke lengths and torque specifications for each model.
- Frame repair procedures like replacing the load wheels.
New holland t5.120 electro command tractor service repair manualfusjejfskekemm
This service manual provides maintenance and repair instructions for T5.100, T5.110, and T5.120 Electro Command tractors. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader, accessories, platform and bodywork. Safety precautions are provided throughout.
New holland t5.110 electro command tractor service repair manualfusjejfskekemm
This service manual provides maintenance and repair instructions for T5.100, T5.110, and T5.120 Electro Command tractors. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader, accessories, and the platform, cab, bodywork and decals. Safety precautions are provided throughout.
New holland t4.85 n tractor service repair manualfusjejfskekemm
This document is a service manual for tractor models T4.75N, T4.85N, T4.95N, T4.105N, T4.65V, T4.75V, T4.85V, T4.95V, and T4.105V. It contains information on engine service, clutch service, transmission service, four-wheel drive systems, front and rear axle systems, power take-off systems, brake systems, and hydraulic systems for these tractor models. The manual is intended to guide service technicians in maintenance, repair, and troubleshooting of components.
New holland l218, l220 tier 4 b (final) skid steer loader service repair manu...fusjejfskekemm
This document is a service manual for New Holland L218 and L220 skid steer loaders that meet Tier 4B emission standards. It contains sections covering the engine, cooling system, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, cab climate control, electrical systems, front loader and bucket, and the platform, cab, bodywork, and decals. Safety information is provided at the beginning regarding servicing the equipment and personal safety precautions.
New holland l170 skid steer service repair manualfusjejfskekemm
This document provides the table of contents for the repair manual for L160 and L170 skid steers. It lists 15 sections that are included in the manual, such as the engine, rear drive axle, brakes, and electrical system. The document focuses on Section 10 for the engine, outlining chapters on general engine information, removal and disassembly, maintenance of engine components, reassembly, installation back into the skid steer frame, and operation of the cooling system. The repair manual contains detailed instructions and specifications to service and repair the engine and other systems.
New holland b80 b backhoe loader service repair manualfusjejfskekemm
This document is a service manual for a Case backhoe loader that contains instructions for servicing and maintaining various systems of the machine, including the engine, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, electrical systems, front loader, booms, dippers, buckets, accessories, and bodywork. It provides part numbers and safety information to technicians servicing the equipment.
This document is a service manual for liquid-cooled horizontal crankshaft engines models LH630, LH685, LH750, and LH760. It contains 11 sections covering safety, troubleshooting, various engine systems, disassembly, inspection, and reassembly. Section 1 provides important safety information, including warnings about rotating parts, hot parts, accidental starts, carbon monoxide, electrical shock, hot liquids, explosive gases, flammable solvents, and recommendations for proper oil, coolant, and fuel types.
Hyster j006 (h6.0 ft europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing and repairing various components of a lift truck, including:
- Side covers, floor plates, seats, dashes, and hoods. Removal and installation steps are provided.
- Counterweights, mufflers, overhead guards, engines, exhaust systems, and LPG fuel tanks. Procedures for checks, repairs, and safety label installation are included.
- Frames, fuel tanks, hydraulic tanks, and counterweight mounts. Component descriptions and identification are given.
- Operator restraint systems including seat belts and hip restraints. Inspection and functionality checks are outlined.
- Hood support assemblies, hood doors, pre-cleaners, and related components
Hyster g019 (h16.00 xm 6 europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing various components of a lift truck, including removing and installing the air cleaner, exhaust system, hood assembly, and hydraulic tank. Key steps include draining fluids, disconnecting hoses and electrical connections, removing mounting hardware, and lifting components away from the frame with caution. Proper identification of removed parts and reinstallation in reverse order is emphasized.
Hyster g005 (h4.00 xl 5) forklift service repair manualfusjejfskekemm
The document provides information about repairing gear pumps. It describes the components and operation of single-stage and tandem gear pumps. The key steps for repair include removal, disassembly, cleaning, inspection, and reassembly. Worn or damaged seals are a common cause of pump failure. The seals can be replaced, but if other components like gears or bearings are worn, a new pump may be more cost effective than repair. Careful documentation of part locations and orientations is important during disassembly and reassembly.
Hyster g004 (s80 ftbcs) forklift service repair manualfusjejfskekemm
This document provides repair procedures for manual and electronic main control valves used in hydraulic lift trucks. There are two main types of control valves - manual and electro-hydraulic. The electro-hydraulic valve uses electronics to control lift, lower, tilt and auxiliary functions. It also has an emergency manual lowering valve. The document describes removing the control valve which involves disconnecting hydraulic hoses and electrical connectors, removing mounting bolts, and removing O-rings between valve sections.
Hyster f006 (h7.00 xl) forklift service repair manualfusjejfskekemm
This document provides a description and repair procedures for the steering axle assembly on various lift truck models. It describes the components of the steering axle including the axle frame, steering cylinder, tie rods, and spindle and hub assemblies. It explains that the steering axle is articulated and connected to the frame with center pivot mounts. The document then provides detailed removal and installation instructions for the steering axle on different lift truck models.
Hyster f005 (h3.50 xl) forklift service repair manualfusjejfskekemm
The document provides instructions for repairing the speed reducer and differential assembly of a lift truck. It includes descriptions of the components, removal and disassembly steps, cleaning and inspection guidelines, and assembly procedures. Some key points:
- The speed reducer and differential are housed together, with the speed reducer transferring power between the transmission and differential gears.
- To repair, the entire drive axle assembly is removed from the lift truck as a unit. It is then disassembled by removing components like the axle shafts, speed reducer housing, ring and pinion gears, and bearings.
- Parts are cleaned and inspected for wear or damage before assembly. Assembly involves installing bearings and gears back into their
Hyster d007 (h190 xl) forklift service repair manualfusjejfskekemm
The document provides repair procedures for a differential. It describes removing and disassembling the differential from the axle housing. Procedures are given for adjusting the pinion bearings and carrier shims to set the pinion depth correctly when installing a new pinion and ring gear set. The ring gear is heated and installed on the differential case half. The case halves are then assembled along with the other differential components and lubricated before installation.
Hyster c114 (ej1.25 xl europe) forklift service repair manualfusjejfskekemm
This document provides instructions for servicing the brake system on certain electric lift truck models. It describes the components and operation of the master cylinder and wheel cylinders. The repair procedures for the master cylinder and brakes on the EJ1.25-1.75XL models are then outlined in detail, including removal, disassembly, inspection, cleaning, and reassembly of the parts. Diagrams are included to illustrate the components and proper assembly. Safety warnings are provided throughout regarding handling of brake components and fluids.
New holland w300 c wheel loader service repair manualfusjejfskekemm
This service manual provides instructions for servicing a Wheel Loader model W270C-W300C. It contains sections covering general information, engines, fuel systems, electrical systems, steering, powertrains, brakes, hydraulics, mounted equipment, and schematics. The document provides section indexes listing topics and their corresponding section numbers for easy navigation. It also includes standard torque specifications for hardware, fluids and lubricants information, and a metric conversion chart.
Hyster b214 (h18.00 xm 12ec europe) forklift service repair manualfusjejfskekemm
1) The document describes the planetary gear axle assembly, which includes an axle housing, two final drive assemblies that are planetary gear units to increase torque to the drive wheels.
2) It provides an overview of the main components - axle shafts, sun gears, planetary pinions, planetary gear carriers, ring gears, and differentials. Service and parking brakes are also installed.
3) The operation section explains how the differential rotation causes the axle shafts and sun gears to rotate, turning the planetary pinions which rotate the planetary spiders and drive wheels, while the ring gear and hub do not rotate.
Hyster a917 (h40.00 xm 12 europe) forklift service repair manualfusjejfskekemm
This document provides descriptions and repair procedures for differentials. It describes the typical components of a differential assembly, including the housing, ring and pinion gear set, and differential assembly. The repair procedures cover removing the differential carrier from the axle housing, removing the differential and ring gear from the carrier, and removing the drive pinion and pinion carrier from the carrier. Detailed steps are provided for disassembling the differential and ring gear assembly and disassembling the drive pinion and pinion carrier.
Hyster a236 (h450 hd) forklift service repair manualfusjejfskekemm
This document provides repair procedures for differentials used in H400HD, H400HDS, H450HD, and H450HDS lift trucks. It describes the components of a typical differential assembly and provides step-by-step instructions for removing the differential carrier from the axle housing, removing the differential and ring gear from the carrier, and removing the drive pinion and pinion carrier. It also gives directions for disassembling the differential and ring gear assembly. Specifications and troubleshooting information are provided at the end.
Hyster a217 (n30 fr) forklift service repair manualfusjejfskekemm
This document provides specifications for various parts and lift capacities for the N30FR, N40EA/ER, N40FR, N45ER, N45FR, N50EA, and N50FA lift truck models. Some key details include:
- The basic lift capacities for each model at a 24 inch and 500mm load center.
- Battery specifications like voltage, compartment size, and battery size/weight for each model.
- Hydraulic system specifications like pump output, relief valve pressures, and tank capacities.
- Reach carriage specifications like stroke lengths and torque specifications for each model.
- Frame repair procedures like replacing the load wheels.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR F4A
Configuration: M314F Wheeled Excavator F4A00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820290
Idler Gear - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7306 Engine Turning Tool 1
B 364-9107
Timing Pin
(Fuel Injection Pump)
1
C 230-6284
Timing Pin
(Camshaft)
1
D
136-4632
Timing Pin
(Crankshaft)
1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
1/6(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel
pump gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02485936
2/6(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g01994553
1. Remove plug (1) from the cylinder block and remove O-ring seal (2) from the plug.
2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
3. Install Tooling (D) through Hole (W) in order to lock the crankshaft so that number one
piston is at top dead center on the compression stroke.
4. Ensure that Tooling (C) is installed into Hole (X) in camshaft gear (3). Use Tooling (C) in
order to lock the camshaft in the correct Position.
Note: Ensure that the gears are marked in order to show alignment. Refer to Illustration 2.
5. Use Tooling (B) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
3/6(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 3 g01994556
6. Use Tooling (E) in order to loosen threaded inserts (5) on all rocker arms (6). Unscrew
threaded inserts (5) on all rocker arms (6) until all valves are fully closed.
Note: Failure to ensure that ALL threaded inserts are fully unscrewed can result in contact
between the valves and pistons.
4/6(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 5 g01994557
7. Mark plate (8) in order to show orientation.
Note: Identification will ensure that the plate can be installed in the original orientation.
8. Remove bolts (7).
9. Remove plate (8).
10. Remove the assembly of idler gear (4).
11. Remove hub (9) from the recess in the front housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 28 11:30:37 UTC+0800 2020
6/6(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR F4A
Configuration: M314F Wheeled Excavator F4A00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820291
Idler Gear - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 364-9107
Timing Pin
(Fuel Injection Pump)
1
C 230-6284
Timing Pin
(Camshaft)
1
D
136-4632
Timing Pin
(Crankshaft)
1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
F
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
1/9(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. (2)
This Tool is used in the aperture for the electric starting motor.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center for No. 1 Piston" for the
correct procedure.
Illustration 1 g02491276
2/9(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g01996475
2. Ensure that Tooling (D) is installed in Hole (W) in the cylinder block. Use Tooling (D) in
order to lock the crankshaft in the correct Position. Refer to System Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
3. Ensure that Tooling (C) is installed into Hole (X) in camshaft gear (3).
4. Use Tooling (B) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
3/9(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 5 g01996576
5. Clean idler gear (4) and inspect the idler gear for wear and damage. Refer to Specifications,
"Gear Group (Front)" for more information. If necessary, replace the idler gear.
6. Clean hub (9) and inspect the hub for wear and damage. Refer to Specifications, "Gear
Group (Front)" for more information. If necessary, replace the hub.
7. Lubricate hub (9) with clean engine oil. Install hub (9) into the recess in the front housing.
Ensure that oil Hole (Z) is to the top of the hub.
8. Install idler gear (4) onto hub (9). Ensure that the timing marks are toward the front of the
idler gear.
9. Align the timing mark on idler gear (4) with the timing mark on camshaft gear (3), fuel
injection pump gear (10) and crankshaft gear (11). Refer to the Illustration 5. Install the
assembly of idler gear (4) to hub (9).
10. Clean plate (8) and inspect the plate for wear and damage. If necessary, replace the plate.
11. Lubricate plate (8) with clean engine oil. Align the holes in plate (8) with the holes in hub
(9). Install the plate in the original orientation.
Note: Ensure that the identification mark TOP is upward.
12. Install bolts (7). Tighten the bolts to a torque of 44 N·m (32 lb ft).
13. Remove Tooling (B), Tooling (C), and Tooling (D).
6/9(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Note: Ensure that timing marks are aligned, before removing the Tooling (B), Tooling (C),
and Tooling (D).
14. Use Tooling (F) in order to check the end play for the idler gear. Refer to Specifications,
"Gear Group (Front)" for more information.
15. Use Tooling (F) in order to check the backlash between the idler gear and the camshaft gear.
Refer to Specifications, "Gear Group (Front)" for more information.
16. Use Tooling (F) in order to check the backlash between the idler gear and the crankshaft
gear. Refer to Specifications, "Gear Group (Front)" for more information.
17. Use Tooling (F) in order to check the backlash between the idler gear and the fuel injection
pump gear. Refer to Specifications, "Gear Group (Front)" for more information.
18. Lightly lubricate all of the gears with clean engine oil.
NOTICE
Failure to ensure that the crankshaft is set in the safe position will
result in interference between the pistons and the valves. Interference
between the pistons and the valves will result in damage to the engine.
19. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
7/9(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 6 g01994556
20. Ensure that the guides for the pushrods are correctly positioned on the threaded inserts (5).
Use Tooling (E) in order to tighten threaded inserts (5) on all rocker arms (6). Tighten the
threaded inserts to a torque of 30 N·m (265 lb in).
Note: When the threaded insert is tightened, the threaded insert must be seated correctly
into the cup for the pushrod.
21. The engine should not be operated for a period 45 minutes after the threaded inserts on all
the rocker arms have been tightened. This period will allow the force of the valve springs to
purge off excessive engine oil from the hydraulic lifters.
8/9(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 7 g02485936
22. Position a new O-ring seal (2) onto plug (1). Install the plug to the cylinder block and
tighten the plug to a torque of 21 N·m (186 lb in).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 28 11:31:33 UTC+0800 2020
9/9(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR F4A
Configuration: M314F Wheeled Excavator F4A00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820292
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the
correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install" for the correct procedure.
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
d. If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
e. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for
the correct procedure.
f. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove and Install" for the correct procedure.
g. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02488340
1. Slide locking tab (1) (not shown) into the unlocked position.
2. Disconnect harness assembly (2) from coolant temperature sensor (3).
3. Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
4. Remove bolts (6) that secure bypass tube (5) to front housing (7).
2/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 5. Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9)
from bypass tube (5).
Illustration 2 g02488341
6. Remove bolts (10), bolts (11) and bolts (12) from front housing (7).
Note: The bolts are three different lengths. Note the positions of the different bolts.
7. Remove front housing (7) from the cylinder block.
8. Remove gasket (13).
3/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 3 g02488356
9. Remove thrust washer (14) from cylinder block (15).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 28 11:32:28 UTC+0800 2020
4/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR F4A
Configuration: M314F Wheeled Excavator F4A00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820293
Housing (Front) - Remove - Heavy Duty Housing (Front)
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the
correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove" for the correct procedure.
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
d. If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
e. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for
the correct procedure.
f. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove and Install" for the correct procedure.
g. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02490356
1. Slide locking tab (1) (not shown) into the unlocked position.
2. Disconnect harness assembly (2) from coolant temperature sensor (3).
3. Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
4. Remove bolts (6) that secure bypass tube (5) to front housing (7).
2/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. 5. Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9)
from bypass tube (5).
Illustration 2 g02490357
6. Remove bolts (11), bolts (12) and bolts (13) from front housing (7).
Note: The bolts are three different lengths. Note the positions of the bolts of different
length.
7. Remove front housing (7) from the cylinder block.
8. Remove gasket (14).
9. If necessary, follow Step 9.a through Step 9.b in order to remove bearing (10) from housing
(7).
a. Place housing (7) onto a suitable support.
b. Use a suitable tool in order to press bearing (10) out of housing (7).
3/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 3 g02490358
10. Remove thrust washer (15) from cylinder block (16).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 28 11:33:24 UTC+0800 2020
4/4(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M314F WHEELED EXCAVATOR F4A
Configuration: M314F Wheeled Excavator F4A00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820294
Housing (Front) - Install - Heavy Duty Housing (Front)
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6640 Sealant 1
B -
Guide Studs
M8 by 80 mm
2
C
319-6486 Alignment Tool 1
-
Bolts
M10 by 50 mm
3
D 1U-6396 O-Ring Assembly Compound 1
E 7M-7456 Bearing Mount Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/8(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Ensure that the wiring harness assembly is correctly routed and the
cable straps are not over tightened. Over tightening of the cable straps
will damage the wiring harness and the convoluting.
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
If necessary, install blanking plugs to a new front housing. Use Tooling (A) in order to seal
all D-plugs.
2. Clean all the gasket surfaces of the cylinder block.
Illustration 1 g02490396
2/8(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. Illustration 2 g02490397
3. Inspect dowel (17) and dowel (18) for damage. If necessary, replace the dowels in the
cylinder block.
4. Install thrust washer (15) into the recess in cylinder block (16). Refer to Disassembly and
Assembly, "Camshaft - Install" for more information.
5. Install Tooling (B) to cylinder block (16). Refer to Illustration 2.
6. Align a new gasket (10) with Tooling (B). Install the gasket to (16) cylinder block.
Note: Ensure that two circular Tabs (X) on the gasket are engaged in two Holes (Y) in
cylinder block (16). Ensure that dowel (18) in cylinder block (16) is engaged on the gasket.
7. Install Tooling (C) to cylinder block (16).
3/8(W)w
2020/4/28https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...