This document provides instructions for disassembling and assembling the main hydraulic pump of a M313D Wheeled Excavator. It lists 36 steps for disassembly, removing components like bolts, valves, pistons, springs, and seals. It then lists 28 steps for assembly, installing components in reverse order and noting specifics like lubrication and torque specifications. The goal is to properly disassemble and reassemble the pump while keeping parts clean to prevent wear and ensuring spring forces are safely released.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...udfjjdjkskkemmd
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing shaft bearings and seals, pistons, springs, and housing components in the reverse order of disassembly. Precise positioning and measurements are required to set component heights and clearances correctly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fujsjjfeskekmm
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing shaft bearings and seals, pistons, springs, and housing components in the reverse order of disassembly. Precise positioning and measurements are required to set component heights and clearances correctly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fhjsjkdmemm
The document provides instructions for disassembling and assembling the main hydraulic pump of an excavator. It lists 31 steps for disassembly, removing components like bolts, seals, springs, and housing pieces. The 34 assembly steps install components in reverse order and include tasks like applying thread lock and installing retaining rings and seals using specialized tools. Precise positioning and cleanliness are emphasized throughout.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fjjsjefkskemm
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing seals, springs, and housing components in the reverse order and ensuring proper alignment and measurements using various tools. Precautions are outlined to contain fluids, mark parts positions, and be aware of spring forces during disassembly and assembly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fjjskekdmem
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing shaft bearings and seals, pistons, springs, and housing components in the reverse order of disassembly. Precise positioning and measurements are required to set component heights and clearances correctly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fhjsjejfjskekemm
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing seals, springs, and housing components in the reverse order and ensuring proper alignment and measurement of clearances using specialized tools. Precautions are outlined to contain fluids, mark parts positions, and safely release spring forces during the processes.
Caterpillar cat m315 d wheeled excavator (prefix w5m) service repair manual (...eudskkejedmm
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...udfjjdjkskkemmd
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing shaft bearings and seals, pistons, springs, and housing components in the reverse order of disassembly. Precise positioning and measurements are required to set component heights and clearances correctly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fujsjjfeskekmm
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing shaft bearings and seals, pistons, springs, and housing components in the reverse order of disassembly. Precise positioning and measurements are required to set component heights and clearances correctly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fhjsjkdmemm
The document provides instructions for disassembling and assembling the main hydraulic pump of an excavator. It lists 31 steps for disassembly, removing components like bolts, seals, springs, and housing pieces. The 34 assembly steps install components in reverse order and include tasks like applying thread lock and installing retaining rings and seals using specialized tools. Precise positioning and cleanliness are emphasized throughout.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fjjsjefkskemm
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing seals, springs, and housing components in the reverse order and ensuring proper alignment and measurements using various tools. Precautions are outlined to contain fluids, mark parts positions, and be aware of spring forces during disassembly and assembly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fjjskekdmem
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing shaft bearings and seals, pistons, springs, and housing components in the reverse order of disassembly. Precise positioning and measurements are required to set component heights and clearances correctly.
Caterpillar cat m313 d wheeled excavator (prefix w3h) service repair manual (...fhjsjejfjskekemm
The document provides instructions for disassembling and assembling the main hydraulic pump of an M313D Wheeled Excavator. It describes 34 steps to disassemble the pump by removing components like bolts, seals, springs, pins, and housing pieces. It then describes 22 steps for reassembly, including installing seals, springs, and housing components in the reverse order and ensuring proper alignment and measurement of clearances using specialized tools. Precautions are outlined to contain fluids, mark parts positions, and safely release spring forces during the processes.
Caterpillar cat m315 d wheeled excavator (prefix w5m) service repair manual (...eudskkejedmm
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. The disassembly procedure involves 34 steps to remove all components of the pump. The assembly procedure involves 24 steps and specifies the required tools and order of installation for all pump components. Dimension measurements and calculations are provided to determine the correct lift-off limitation without shim.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using tools to set specifications like the lift-off limitation. Precautions are provided to prevent contamination and release of spring forces during the process.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. The disassembly procedure involves 34 steps to remove all components of the pump. The assembly procedure involves 24 steps and specifies the required tools and order of installation for all pump components. Dimension measurements and calculations are provided to determine the correct lift-off limitation without shim.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then lists 31 steps for assembly, replacing components and using tools to set dimensions and install retaining rings, seals, bearings, and other parts back into their original positions. Precise assembly is important to prevent contamination and ensure proper pump function.
The document provides instructions for disassembling and assembling the main hydraulic pump on a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, seals, springs, pistons and other components. It then lists 36 steps for reassembly, instructing technicians to clean parts, apply threadlock and grease, and install components in reverse order of removal, taking care with orientation. Special tools are listed for removing seals and bearings.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, installing components in reverse order and noting markings and orientations. Precision measurements are taken to ensure correct assembly tolerances using various tools like gauges, hubs and bells. Loctite is applied and heat is used in some steps.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
The document provides instructions for disassembling and assembling the main hydraulic pump on a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, seals, springs, pistons and other components. It then lists 36 steps for reassembly, instructing technicians to clean parts, apply threadlock and grease, and install components in reverse order of disassembly, taking care with orientation of marked parts. Special tools are listed that are required for tasks like removing seals and bearings.
The document provides instructions for disassembling and assembling the main hydraulic pump on a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, valves, pistons, springs, and other components. It then lists 36 steps for reassembly, instructing technicians to clean parts, apply threadlock, and reinstall components in reverse order of disassembly using the provided tools. Technicians are advised to mark parts for orientation during reassembly to prevent mixing of components.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, installing components in reverse order and noting markings and orientations. Precision measurements are taken to ensure correct assembly tolerances using various tools like test rings, measuring hubs and gauges. Loctite is applied and heat is used in some steps.
Caterpillar cat m315 d wheeled excavator (prefix w5m) service repair manual (...jfdjskmdmme
The document provides instructions for disassembling and assembling the main hydraulic pump of an M315D Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, valves, pistons, springs, and other components. It then lists 36 steps for reassembly, instructing technicians to install components like bearings, seals, races, and screws in the reverse order of disassembly. Precise positioning and orientation of parts is emphasized for correct reassembly.
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 36 steps for disassembly, including removing components like the valve assembly, pistons, springs, and bearings. It then lists 29 steps for assembly, including installing bearings, pistons, springs, and ensuring proper alignment of components. Safety notices are provided throughout to warn of potential injuries from released pressures or springs.
KOBELCO 140SRLC-3 HYDRAULIC EXCAVATOR Service Repair Manual.pdfjdkksmemmd
This service manual provides instructions for maintenance, repair, and troubleshooting of a Kobelco 140SRLC-3 hydraulic excavator. It begins with general safety information and precautions for working on the machine. The manual is divided into 7 sections covering specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and optional attachments. Technicians are advised to thoroughly prepare and clean the machine before starting any repairs.
KOBELCO 70SR-2 Acera Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
The document is a service manual that provides instructions for disassembling a pilot valve used in a Kobelco Construction Machinery hydraulic excavator model 70SR-2 Acera. It includes diagrams of the valve components and specifies tightening torques. The disassembly instructions describe removing external components like boots and nuts, then internal parts like springs, spools and seals while taking safety precautions for any stored energy in the valve springs.
KOBELCO 17SR-Tier 4 Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
This document provides guidelines and safety precautions for repairing hydraulic excavators. It covers preparing for disassembly, safety during disassembly and assembly, working with hydraulic equipment and electrical components, handling hydraulic parts, welding repairs, and an international unit conversion system. Technicians are instructed to thoroughly read manuals, use proper tools, relieve pressures, and take caution with hot or heavy components. Protective equipment is recommended.
Komatsu WA270PT-3 Wheel Loader Service Repair Manual SN WA270H30051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which requires draining fluids, removing wiring, hoses, and other attachments to the engine before lifting it out.
3) Additional sections provide instructions for removing and installing other components like the radiator, fuel tank, and counterweight. Precise steps are outlined, safety precautions noted, and proper torque specifications and fluid fill amounts are provided.
Komatsu WA270-3 Wheel Loader Service Repair Manual SN WA270H20051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which has many steps including draining fluids, removing wiring, hoses, and mounting components.
3) Procedures for removing and installing other major components like the radiator, fuel tank, and counterweight. Detailed safety precautions and instructions are provided.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkksmemmd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix PJW) Service Repair Manual...jdkksmemmd
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housed within sprocket and motor housings. Bearings must be properly seated and preloaded during assembly. Seals, shims, and other components are also installed according to detailed steps. Proper cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
More Related Content
Similar to Caterpillar Cat M313D WHEELED Excavator (Prefix W3H) Service Repair Manual (W3H00001 and up).pdf
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. The disassembly procedure involves 34 steps to remove all components of the pump. The assembly procedure involves 24 steps and specifies the required tools and order of installation for all pump components. Dimension measurements and calculations are provided to determine the correct lift-off limitation without shim.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using tools to set specifications like the lift-off limitation. Precautions are provided to prevent contamination and release of spring forces during the process.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. The disassembly procedure involves 34 steps to remove all components of the pump. The assembly procedure involves 24 steps and specifies the required tools and order of installation for all pump components. Dimension measurements and calculations are provided to determine the correct lift-off limitation without shim.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like bolts, seals, springs, and bearings. It then lists 31 steps for assembly, replacing components and using tools to set dimensions and install retaining rings, seals, bearings, and other parts back into their original positions. Precise assembly is important to prevent contamination and ensure proper pump function.
The document provides instructions for disassembling and assembling the main hydraulic pump on a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, seals, springs, pistons and other components. It then lists 36 steps for reassembly, instructing technicians to clean parts, apply threadlock and grease, and install components in reverse order of removal, taking care with orientation. Special tools are listed for removing seals and bearings.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, installing components in reverse order and noting markings and orientations. Precision measurements are taken to ensure correct assembly tolerances using various tools like gauges, hubs and bells. Loctite is applied and heat is used in some steps.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
The document provides instructions for disassembling and assembling the main hydraulic pump on a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, seals, springs, pistons and other components. It then lists 36 steps for reassembly, instructing technicians to clean parts, apply threadlock and grease, and install components in reverse order of disassembly, taking care with orientation of marked parts. Special tools are listed that are required for tasks like removing seals and bearings.
The document provides instructions for disassembling and assembling the main hydraulic pump on a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, valves, pistons, springs, and other components. It then lists 36 steps for reassembly, instructing technicians to clean parts, apply threadlock, and reinstall components in reverse order of disassembly using the provided tools. Technicians are advised to mark parts for orientation during reassembly to prevent mixing of components.
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, installing components in reverse order and noting markings and orientations. Precision measurements are taken to ensure correct assembly tolerances using various tools like test rings, measuring hubs and gauges. Loctite is applied and heat is used in some steps.
Caterpillar cat m315 d wheeled excavator (prefix w5m) service repair manual (...jfdjskmdmme
The document provides instructions for disassembling and assembling the main hydraulic pump of an M315D Wheeled Excavator. It lists 34 steps for disassembly, including removing bolts, valves, pistons, springs, and other components. It then lists 36 steps for reassembly, instructing technicians to install components like bearings, seals, races, and screws in the reverse order of disassembly. Precise positioning and orientation of parts is emphasized for correct reassembly.
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315D Wheeled Excavator. It lists 36 steps for disassembly, including removing components like the valve assembly, pistons, springs, and bearings. It then lists 29 steps for assembly, including installing bearings, pistons, springs, and ensuring proper alignment of components. Safety notices are provided throughout to warn of potential injuries from released pressures or springs.
Similar to Caterpillar Cat M313D WHEELED Excavator (Prefix W3H) Service Repair Manual (W3H00001 and up).pdf (12)
KOBELCO 140SRLC-3 HYDRAULIC EXCAVATOR Service Repair Manual.pdfjdkksmemmd
This service manual provides instructions for maintenance, repair, and troubleshooting of a Kobelco 140SRLC-3 hydraulic excavator. It begins with general safety information and precautions for working on the machine. The manual is divided into 7 sections covering specifications, maintenance, systems, disassembly, troubleshooting, engine procedures, and optional attachments. Technicians are advised to thoroughly prepare and clean the machine before starting any repairs.
KOBELCO 70SR-2 Acera Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
The document is a service manual that provides instructions for disassembling a pilot valve used in a Kobelco Construction Machinery hydraulic excavator model 70SR-2 Acera. It includes diagrams of the valve components and specifies tightening torques. The disassembly instructions describe removing external components like boots and nuts, then internal parts like springs, spools and seals while taking safety precautions for any stored energy in the valve springs.
KOBELCO 17SR-Tier 4 Hydraulic Excavator Service Repair Manual.pdfjdkksmemmd
This document provides guidelines and safety precautions for repairing hydraulic excavators. It covers preparing for disassembly, safety during disassembly and assembly, working with hydraulic equipment and electrical components, handling hydraulic parts, welding repairs, and an international unit conversion system. Technicians are instructed to thoroughly read manuals, use proper tools, relieve pressures, and take caution with hot or heavy components. Protective equipment is recommended.
Komatsu WA270PT-3 Wheel Loader Service Repair Manual SN WA270H30051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which requires draining fluids, removing wiring, hoses, and other attachments to the engine before lifting it out.
3) Additional sections provide instructions for removing and installing other components like the radiator, fuel tank, and counterweight. Precise steps are outlined, safety precautions noted, and proper torque specifications and fluid fill amounts are provided.
Komatsu WA270-3 Wheel Loader Service Repair Manual SN WA270H20051 and up.pdfjdkksmemmd
This document provides instructions for servicing a wheel loader, including:
1) Removing and installing the engine hood, which requires disconnecting wiring, hoses, and other components.
2) Removing and installing the engine, which has many steps including draining fluids, removing wiring, hoses, and mounting components.
3) Procedures for removing and installing other major components like the radiator, fuel tank, and counterweight. Detailed safety precautions and instructions are provided.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkksmemmd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix PJW) Service Repair Manual...jdkksmemmd
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housed within sprocket and motor housings. Bearings must be properly seated and preloaded during assembly. Seals, shims, and other components are also installed according to detailed steps. Proper cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...jdkksmemmd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...jdkksmemmd
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and installation of identification marks are emphasized to ensure correct reassembly of components. Tools required are also listed.
The document provides instructions for disassembling and assembling the front axle of a M322D MH Wheeled Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, thrust washers, retaining rings, and bearings. Instructions are provided to remove the ring gear housing, carrier gear, piston, seals, discs, and hub. Precautions and notes are included to aid the technician.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant and ensuring proper torque specifications are followed for nuts and bolts. Cleanliness and use of the correct tools are emphasized throughout.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, bearing cones, shims, seals, sprockets, gears and carriers. Proper bearing preload is critical and is achieved through measuring clearances and determining the correct shim thickness. Lifting devices and clean lubricant are used during assembly to install heavy components like the sprocket housing and carrier assemblies.
This document provides assembly instructions for a hydraulic pump in 3 steps:
1. Install various internal components of the pump like bearings, pistons, seals according to 61 illustrated steps.
2. Attach the pump control unit with additional internal components like springs, valves, fittings in 59 illustrated steps.
3. Connect the assembled hydraulic pump and control unit together and install it on the excavator by securing with bolts.
This document provides disassembly instructions for the final drive carriers, hubs, and brakes on the front and rear axles of an M322C wheeled excavator. It lists 41 steps to fully disassemble the components, including removing retaining rings, gears, bearings, seals, and other parts using various specialized tools. Detailed illustrations accompany each step to show how to remove the individual pieces and subassemblies. Safety notices are also provided regarding releasing pressure and containing fluids before disassembly.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkksmemmd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...jdkksmemmd
The document provides instructions for disassembling and assembling a travel motor. It is a 28 step process that includes removing parts like seals, bearings, and housing components. Precision is required to reinstall the springs, pistons, and other small parts correctly. The final steps are to install the motor housing cover and tighten the bolts to the specified torque.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M313D WHEELED EXCAVATOR W3H
Configuration: M313D Excavator W3H00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
M313D Wheeled Excavator Machine Systems
Media Number -KENR6025-04 Publication Date -01/03/2017 Date Updated -06/03/2017
i02817263
Main Hydraulic Pump - Disassemble
SMCS - 5070-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 1U-7600 Slide Hammer Puller Gp 1
Start By:
a. Remove the main hydraulic pump. Refer to Disassembly and Assembly, "Main Hydraulic
Pump and Pump Drive Coupling - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Note the location and orientation of the components for assembly purposes.
Illustration 1 g01247191
Illustration 2 g01247153
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (3) and valve assembly (2).
2. Remove plug (1) and the O-ring seal from piston pump (4).
Illustration 3 g01173466
3. Remove roller (7), spring (6), and piston (5).
Illustration 4 g01247146
4. Remove nut (8) and coil (9).
3/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g01247149
5. Remove cartridge (10), O-ring seal (11), pin (12), plug (13), and the O-ring seal.
Illustration 6 g01247151
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
6. Remove cap (24), plug (23), O-ring seal (22), spring retainer (21), spring (20), spring (19),
spring retainer (18), pin (17), spacer (16), spool (15), and housing (14).
4/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 7 g01247258
7. Remove plug (25) and plug (26).
8. Remove cap (31), plug (30), O-ring seal (28), fitting (29), and pin (27).
Illustration 8 g01247262
9. Remove pins (32), O-ring seals (33), O-ring seal (34), pin (35), and lever (36).
Illustration 9 g01173603
10. Remove coupling (38), O-ring seal (39), bolts (37), and flange (40).
5/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 10 g01173605
11. Remove O-ring seal (41) from flange (40).
Illustration 11 g01173606
Illustration 12 g01173608
Personal injury can result from being struck by parts propelled by a
released spring force.
6/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove bolts (43) and pump adapter (42).
Note: Seat adjusters (44) and (45) will come apart as pump adapter (42) is being removed.
To prevent mixing of parts, slowly remove pump adapter (42).
Illustration 13 g01173609
Illustration 14 g01173615
7/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 15 g01173616
13. Remove rods (46).
14. Mark the position of port plate (47) in relation to pump adapter (42) for assembly purposes.
Remove port plate (47).
15. Remove spring (48) from seat adjuster (44).
16. Remove bushing (49), spring (50), and rod (51) from seat adjuster (45).
Illustration 16 g01173619
17. Remove bearing (52), plugs (53), and the O-ring seals from pump adapter (42).
8/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 17 g01312794
18. Mark the position of the maximum angle stop screw (54) prior to removal from the piston
pump (4). Remove maximum angle stop screw (54). Repeat for the opposite side of the
piston pump in order to remove the minimum angle stop screw.
Illustration 18 g01312797
19. Remove O-ring seal (57). Remove swashplate (56) and rotating assembly (55) as one piece.
Illustration 19 g01312798
9/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 20 g01312799
Note: Mark barrel (63), pistons (58), and swashplate (56) for orientation.
20. The swashplate must be heated in order to melt the thread lock . Remove bolts (62) from
swashplate (56).
Note: Bolts (62) should be replaced with new bolts.
21. Remove retainers (60) and (61) from swashplate (56).
22. Remove rotating assembly (55) from swashplate (56).
Illustration 21 g01312800
10/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 22 g01312801
23. Remove pistons (58) from barrel (63).
24. Remove retainer plate (59) from pistons (58).
Illustration 23 g01312802
Illustration 24 g01312803
25. Remove retainer (64) from barrel (63).
26. Remove cup springs (65) and shims (66) from barrel (63).
Note: Mark orientation of cup springs (65) and shims (66) for installation.
11/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 25 g01312804
27. Remove plugs (67) and slotted pins (68).
Illustration 26 g01312805
28. Remove rods (69) from swashplate (57).
Illustration 27 g01312807
29. Remove bearings (70 ) from piston pump (4).
12/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 28 g01312808
30. Remove outer races (71) from piston pump (4).
Illustration 29 g01312809
31. Use Tooling (A) to remove retaining ring (72).
32. Use Tooling (B) to remove seal (73).
33. Use Tooling (A) to remove retaining ring (74).
Illustration 30 g01312812
34. Remove shaft (75) from the piston pump.
13/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 31 g01312814
35. Use Tooling (A) to remove retaining ring (76) from shaft (74).
36. Remove bearing (77) from shaft (75). Use a suitable press to remove bearing (77).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Apr 26 21:34:34 UTC+0800 2020
14/14(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M313D WHEELED EXCAVATOR W3H
Configuration: M313D Excavator W3H00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
M313D Wheeled Excavator Machine Systems
Media Number -KENR6025-04 Publication Date -01/03/2017 Date Updated -06/03/2017
i06804170
Main Hydraulic Pump - Assemble
SMCS - 5070-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
C
464-4892(1)
Test Ring 1
128-2746(2)(3)
Test Ring 1
D
129-3873(1)
Measuring Hub 1
129-3874(2)(3)
Measuring Hub 1
E 128-2744 Measuring Bell 1
F - Vernier Height Gauge 1
G 1P-0510 Driver Gp 1
H
464-4893(1)
Alignment Plug 1
128-2742(2)
Alignment Plug 1
437-5508(3)
Alignment Plug 1
J - Loctite 242 -
(1)
Use for 95 cc pumps.
(2)
Use for 130 cc pumps.
(3)
Use for 145 cc pumps.
1/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01312814
1. Use Tooling (A) to install bearing (77) to shaft (75). Raise the temperature of bearing (77).
Install retaining ring (76) to shaft (75).
Illustration 2 g01313371
2. Install shaft (75) into the piston pump.
2/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 3 g01312809
3. Use Tooling (A) to install retaining ring (74).
4. Use Tooling (G) to install seal (73).
5. Use Tooling (A) to install retaining ring (72).
Illustration 4 g01312808
6. Install outer races (71) to piston pump (4).
Illustration 5 g01312805
7. Install rods (69) to swashplate (57).
3/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 6 g01313372
Illustration 7 g01313374
8. Install bearings (70) to swashplate (56). Install a rubber band to each of bearings (70). The
rubber band will hold bearings (70) to swashplate (56).
9. Carefully install swashplate (56) to piston pump (4).
Illustration 8 g01313375
10. Cut the rubber band on swashplate (56).
4/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 9 g01312804
Note: Rods (68) must engage slotted pins (68).
11. Install plugs (67) and slotted pins (68).
Illustration 10 g01312794
12. Install the maximum angle stop screw (54). Repeat for the opposite side of piston pump (4)
to install the minimum angle stop screw.
Illustration 11 g01173661
13. Place port plate (47) on a surface plate.
5/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 12 g01173662
14. Install Tooling (H) to port plate (47).
Illustration 13 g01313379
15. Install barrel (63) onto Tooling (H) and port plate (47).
Illustration 14 g01313380
16. Install Tooling (C) to retainer (64). Shims and springs must be removed from retainer (64).
6/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 15 g01313382
17. Install retainer (64) to barrel (63).
Illustration 16 g01313384
18. Install retainer plate (59) to retainer (64).
Illustration 17 g00903603
19. Bolt Tooling (D) to Tooling (E).
7/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 18 g01313386
20. Install assembled Tooling (D) and Tooling (E) into the splined bores of retainer (64). Make
sure that Tooling is properly seated.
Illustration 19 g01313387
21. Record the dimension that is stamped on the side of Tooling (E). This dimension is the
distance from the top of retainer plate (59) to the top of Tooling (E). This dimension is
called Dimension (W).
Illustration 20 g00903619
8/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 22. Use Tooling (F) to measure the distance from the top of the surface plate to the top of
Tooling (E). Record this dimension. Call this Dimension (X).
23. Use the following calculation: Dimension (X) - Dimension (W) = Dimension (Y).
24. Dimension (Y) is the correct lift-off limitation without shim (66).
Note: This is the correct lift-off limitation for the 95 cc main hydraulic pump.
122.65 + 0.0 − 0.200 mm (4.8287 + 0.00 − 0.0078 inch) Call this Dimension (Z).
Note: This is the correct lift-off limitation for the 130 cc and 145 cc main hydraulic pump.
136.95 + 0.0 − 0.200 mm (5.3917 + 0.00 − 0.0078 inch) Call this Dimension (Z).
25. Use the following calculation: Dimension (Z) - Dimension (Y) = Thickness of shim (66).
Note: Shim (66) is available in several thicknesses. Select the correct thickness of shim (66)
to obtain the correct lift-off limitation. Only one shim (66) should be used.
Illustration 21 g01312802
Illustration 22 g01312803
26. Install cup springs (65) and shim (66) to barrel (63).
27. Install retainer (64) to barrel (63).
9/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 23 g01312801
28. Install pistons (58) to retainer plate (59).
Illustration 24 g01312800
29. Install retainer plate (59) with pistons (58) to barrel (63).
Illustration 25 g01313388
10/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 26 g01313391
Illustration 27 g01313392
30. Install rotating assembly (55) into piston pump (4).
31. Install retainers (61) and bolts (62). Use Tooling (J) on bolts (62).
Note: Bolts (62) should be replaced with new bolts.
32. Install O-ring seal (57) to piston pump (4).
Illustration 28 g01173619
33. Install bearing (52), plugs (53), and the O-ring seals in pump adapter (42).
11/18(W)
w
2020/4/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...