Caterpillar Cat D9T TRACK-TYPE TRACTOR (Prefix RJS) Service Repair Manual (RJS00001 and up).pdf

Service Repair Manual
Models
D9T TRACK-TYPE TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D9T TRACK-TYPE TRACTOR RJS
Configuration: D9T Track-Type Tractor RJS00001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
D9T Track-Type Tractor Power Train
Media Number -RENR7471-06 Publication Date -01/03/2015 Date Updated -23/08/2018
i06163231
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 138-7575 Link Bracket 8
C 138-7574 Link Bracket 3
D 138-7573 Link Bracket 5
E 5B-4274 Bolt 2
F 1P-0520 Driver Gp 1
G
8B-7559 Adapter 2
8B-7550 Push-Puller Leg 2
3H-0465 Push-Puller Plate 4
1P-5546 Crossarm 1
5P-8715 Forcing Bolt 1
6B-6682 Full Nut 2
H 1U-9478 Nut 1
257-5128 Fixture 1
378-4529 Spanner Wrench As 1
1/13
D9T Track-Type Tractor RJS00001-UP (MACHINE) POWERED BY C18 Engine(SE...
2020/3/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

6V-6080 Torque Multiplier Gp 1
J 8B-7551 Puller Assembly 1
Start By:
a. Remove the torque converter. Refer to Disassembly and Assembly, "Torque Converter -
Remove".
Illustration 1 g01092983
1. Remove bolts (1) and relief valve (2).
2. Remove bolt (3) and retainer (4).
2/13
2020/3/11

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

3. Remove O-ring seal (5) and yoke assembly (6).
4. Remove bolts (7) to remove bearing retainer (8).
5. Remove O-ring seals (9) from bearing retainer (8).
3/13
2020/3/11

6. Remove seal (10) from bearing retainer (8).
7. Loosen nut (11).
8. Remove speed sensor (12) from bearing retainer (8).
9. Attach Tooling (A), Tooling (B), Tooling (C), and a suitable lifting device to torque
converter cover (13).
10. Invert the torque converter. The weight of the torque converter is approximately 340 kg
(750 lb).
11. Remove Tooling (A) and Tooling (C).
4/13
2020/3/11

12. Attach Tooling (A), Tooling (D), and a suitable lifting device to torque converter (13).
13. Remove bolts (14) and torque converter cover (13). The weight of the torque converter
cover is approximately 125 kg (275 lb).
14. Remove O-ring seal (15) from torque converter cover (13).
15. Attach Tooling (C) and a suitable lifting device to output shaft (16).
5/13
2020/3/11

16. Remove output shaft (16).
17. Remove seal ring (17) from ring carrier (18). Remove ring carrier (18) from output shaft
(16).
18. Remove bearing (19) from output shaft (16).
19. Remove bolts (20).
6/13
2020/3/11

20. Attach Tooling (D) and a suitable lifting device to stator support (21).
21. Use Tooling (E) to remove stator support (21).
22. Remove O-ring seals (22) from stator support (21).
23. Remove spring pins (23) from stator support (21).
24. Remove seal ring (25) from seal carrier (24).
25. Remove seal carrier (24) from stator support (21).
7/13
2020/3/11

26. Attach Tooling (B) and a suitable lifting device to stator carrier (26).
27. Remove bolts (27) and stator carrier (26) from rotating housing (28). The weight of stator
carrier (26) is approximately 61 kg (135 lb).
28. Remove bolts (33) from wear sleeve (30). Remove impeller (31).
29. Remove cap (34) from impeller (31).
8/13
2020/3/11

30. Place the carrier assembly into a press. Remove retaining ring (35).
31. Use Tooling (F) to separate stator carrier (26) from stator (36).
9/13
2020/3/11

32. Install Tooling (J) onto carrier (26). Install Tooling (J) and carrier (26) into a press.
33. Install Tooling (F) onto carrier (26). Remove bearing (29) from carrier (26). Remove
retaining ring (35) after bearing (29) has been removed.
34. Remove bolts (37) to remove cover (38) from rotating housing (28).
10/13
D9T Track-Type Tractor RJS00001-UP (MACHINE) POWERED BY C18 Engine(...
2020/3/11

35. Remove retaining ring (39) from bearing (40).
36. Attach Tooling (D) and a suitable lifting device to rotating housing (28).
37. Remove rotating housing (28) from turbine (41). The weight of the rotating housing is
approximately 57 kg (125 lb).
11/13
2020/3/11

38. Remove set screw (42) from locknut (43).
39. Use Tooling (H) to remove locknut (43) from retainer (44).
40. Remove lockwasher (45) from retainer (44).
41. Remove retainer (44) from turbine (41).
12/13
2020/3/11

42. Remove bearing (40) from retainer (44).
43. Remove bolts (46).
44. Remove turbine (41) from hub (47).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Mar 11 11:43:18 UTC+0800 2020
13/13
2020/3/11

Shutdown SIS
Previous Screen
i06163241
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
A 1U-9200 Lever Puller Hoist 1
B 138-7575 Link Bracket 8
C 138-7574 Link Bracket 3
D 138-7573 Link Bracket 5
F 1P-0520 Driver Gp 1
H
1U-9478 Nut 1
257-5128 Fixture 1
378-4529 Spanner Wrench As 1
6V-6080 Torque Multiplier Gp 1
1/13
2020/3/11

1. Install turbine (41) onto hub (47).
2. Install bolts (46). Tighten bolts (46) to a torque of 120 ± 15 N·m (89 ± 11 lb ft).
3. Raise the temperature of bearing (40).
4. Install bearing (40) onto retainer (44).
5. Install retainer (44) onto turbine (41).
2/13
2020/3/11

6. Install lockwasher (45) onto retainer (44).
7. Use Tooling (H) to install locknut (43) onto retainer (44). Tighten locknut (43) to a torque
of 985 ± 35 N·m (726 ± 26 lb ft).
8. Install set screw (42) into locknut (43).
3/13
2020/3/11

9. Lower the temperature of turbine (41).
10. Attach Tooling (D) and a suitable lifting device to rotating housing (28).
11. Install rotating housing (28) onto turbine (41). The weight of the rotating housing is
12. Install retaining ring (39) onto bearing (40).
4/13
2020/3/11

13. Install cover (38) and bolts (37) onto rotating housing (28).
14. Lower the temperature of stator carrier (26).
15. Install stator (36) onto stator carrier (26).
16. Install retaining ring (35) onto stator carrier (26).
5/13
2020/3/11

17. Install impeller (32) onto stator carrier (26).
18. Raise the temperature of bearing cone (29).
19. Install bearing cone (29) onto stator carrier (26).
20. Lower the temperature of bearing cup (34).
21. Install bearing cup (34) from impeller flange (31).
22. Install impeller flange (31).
23. Install wear sleeve (30) and bolts (33). Tighten bolts (33) to a torque of 120 ± 20 N·m
(89 ± 15 lb ft).
6/13
2020/3/11

24. Attach Tooling (B) and a suitable lifting device to stator carrier (26).
25. Install the stator carrier onto rotating housing (28). The weight of the stator carrier is
27. Raise the temperature of seal carrier to a maximum temperature of 66 °C (150 °F).
28. Install seal carrier (24) onto stator support (21).
29. Install seal ring (25) onto seal carrier (24).
30. Install spring pins (23) onto stator support (21).
7/13
2020/3/11

31. Install O-ring seals (22) onto stator support (21).
32. Attach Tooling (D) and a suitable lifting device to stator support (21).
33. Install stator support (21).
8/13
2020/3/11

35. Raise temperature of bearing (19).
36. Install bearing (19) onto output shaft (16).
37. Install ring carrier (18) onto output shaft (16). Install seal ring (17) onto ring carrier (18).
38. Attach Tooling (C) and a suitable lifting device to output shaft (16).
39. Install output shaft (16).
9/13
2020/3/11

40. Install O-ring seal (15) onto torque converter cover (13).
41. Attach Tooling (A), Tooling (D), Tooling (B), and a suitable lifting device to torque
converter (13).
42. Install torque converter cover (13) and bolts (14). The weight of the torque converter cover
is approximately 125 kg (275 lb).
43. Attach Tooling (A), Tooling (B), Tooling (C), and a suitable lifting device to torque
converter cover (13).
44. Invert the torque converter. The weight of the torque converter is approximately 340 kg
(750 lb).
10/13
2020/3/11

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

45. Use Tooling (F) to install seal (10) into bearing retainer (8).
46. Install speed sensor (12) and nut (11) onto bearing retainer (8). Do not tighten nut (11) now.
47. Install O-ring seals (9) onto bearing retainer (8).
48. Install bearing retainer (8) and bolts (7).
11/13
2020/3/11

49. Install yoke assembly (6) and O-ring seal (5).
50. Install retainer (4) and bolt (3). Tighten bolt 3 to a torque of 240 ± 25 N·m (177 ± 18 lb ft).
51. Install speed sensor (12) until speed sensor (12) contacts the center of one of the teeth on
yoke assembly (6).
52. Loosen speed sensor (12) by half a turn.
53. Tighten nut (11) to a torque of 25 ± 5 N·m (18 ± 4 lb ft).
12/13
2020/3/11

54. Install relief valve (2) and bolts (1).
End By:
a. Install the torque converter. Refer to Disassembly and Assembly, "Torque Converter -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Mar 11 11:44:18 UTC+0800 2020
13/13
2020/3/11

Shutdown SIS
Previous Screen
i02210377
Torque Converter - Install
SMCS - 3101-012
Installation Procedure
Table 1
Required Tools
A 138-7574 Link Bracket 2
1/6
2020/3/11

Caterpillar Cat D9T TRACK-TYPE TRACTOR (Prefix RJS) Service Repair Manual (RJS00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat D9T TRACK-TYPE TRACTOR (Prefix RJS) Service Repair Manual (RJS00001 and up).pdf

Similar to Caterpillar Cat D9T TRACK-TYPE TRACTOR (Prefix RJS) Service Repair Manual (RJS00001 and up).pdf (20)

More from ls7q63nz4g

More from ls7q63nz4g (8)

Recently uploaded

Recently uploaded (19)

Caterpillar Cat D9T TRACK-TYPE TRACTOR (Prefix RJS) Service Repair Manual (RJS00001 and up).pdf