This document provides instructions for removing the rear gear group and flywheel from a Caterpillar 3408 engine. It describes:
1) Using various tools to support, press and pull components like the gear assembly, bearings and flywheel out of the adapter assembly and crankshaft.
2) Removing bolts and gears from the flywheel housing and crankshaft.
3) Disassembling individual gears by pressing out bearings and shafts.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 53y) service ...ufjjdjffjkskemm
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and adapter assemblies. The flywheel is removed by installing holding tools and using another tool attached to an overhead hoist. The installation procedure outlines reassembling the components and pressing or installing bearings back into place. Proper cleaning and lubrication of parts is emphasized.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
Caterpillar cat 345 b excavator (prefix amd) service repair manual (amd00001 ...fjsekdmmeed
This document provides assembly instructions for a travel motor on a 345B Excavator. It outlines 33 steps to assemble internal components like pistons, seals, plates and housing pieces. Measurement checks are included to ensure correct assembly. The instructions also cover installing the assembled travel motor by cleaning mating surfaces, replacing an O-ring seal, and using lifting tools to slide the motor into position in the final drive housing.
Caterpillar cat 340 f excavator (prefix rbd) service repair manual (rbd00001 ...fjsekdmmeed
This document provides instructions for removing and installing the fuel manifold (rail) on a C9.3 engine. The removal procedure involves disconnecting harness assemblies, tube assemblies, and removing bolts to access the fuel manifold. Sensors, solenoid valves, and other components are then removed from the manifold. Installation is the reverse of removal, with all components torqued to the specified values. Safety notices warn of hazards from high pressure fuel and ensure cleanliness to prevent contamination of fuel system components.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group components. Assembly steps are then listed in reverse order and include installing seals, spacers, piston assemblies, springs and other components back into the travel motor housing. Precautions are given such as cleaning parts and applying lubricant before assembly.
Caterpillar cat 24 h motor grader (prefix 7kk) service repair manual (7kk0000...fjskekdmjekm
This service repair manual provides instructions for removing and installing various engine components on a 24H Motor Grader with a 3412E engine. The document includes procedures for removing and installing the engine support, rear gear group, flywheel, and other parts. Detailed illustrations and lists of required tools accompany each procedure. Safety notices remind technicians to keep parts clean and prevent contamination.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
Caterpillar cat 345 c excavator (prefix jar) service repair manual (jar00001 ...fjkskedmme
This document provides instructions for removing and installing the rear gear group on a 345C excavator. It details:
1) The required tools and parts for the job.
2) The step-by-step removal procedure which includes removing the electric starting motor, flywheel, rear gear components, seals, and bearings.
3) The installation procedure which provides directions for installing the rear gear group components in reverse order and ensuring proper bearing placement and torque specifications are followed.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 53y) service ...ufjjdjffjkskemm
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and adapter assemblies. The flywheel is removed by installing holding tools and using another tool attached to an overhead hoist. The installation procedure outlines reassembling the components and pressing or installing bearings back into place. Proper cleaning and lubrication of parts is emphasized.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
Caterpillar cat 345 b excavator (prefix amd) service repair manual (amd00001 ...fjsekdmmeed
This document provides assembly instructions for a travel motor on a 345B Excavator. It outlines 33 steps to assemble internal components like pistons, seals, plates and housing pieces. Measurement checks are included to ensure correct assembly. The instructions also cover installing the assembled travel motor by cleaning mating surfaces, replacing an O-ring seal, and using lifting tools to slide the motor into position in the final drive housing.
Caterpillar cat 340 f excavator (prefix rbd) service repair manual (rbd00001 ...fjsekdmmeed
This document provides instructions for removing and installing the fuel manifold (rail) on a C9.3 engine. The removal procedure involves disconnecting harness assemblies, tube assemblies, and removing bolts to access the fuel manifold. Sensors, solenoid valves, and other components are then removed from the manifold. Installation is the reverse of removal, with all components torqued to the specified values. Safety notices warn of hazards from high pressure fuel and ensure cleanliness to prevent contamination of fuel system components.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group components. Assembly steps are then listed in reverse order and include installing seals, spacers, piston assemblies, springs and other components back into the travel motor housing. Precautions are given such as cleaning parts and applying lubricant before assembly.
Caterpillar cat 24 h motor grader (prefix 7kk) service repair manual (7kk0000...fjskekdmjekm
This service repair manual provides instructions for removing and installing various engine components on a 24H Motor Grader with a 3412E engine. The document includes procedures for removing and installing the engine support, rear gear group, flywheel, and other parts. Detailed illustrations and lists of required tools accompany each procedure. Safety notices remind technicians to keep parts clean and prevent contamination.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjskefkemms
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
Caterpillar cat 345 c excavator (prefix jar) service repair manual (jar00001 ...fjkskedmme
This document provides instructions for removing and installing the rear gear group on a 345C excavator. It details:
1) The required tools and parts for the job.
2) The step-by-step removal procedure which includes removing the electric starting motor, flywheel, rear gear components, seals, and bearings.
3) The installation procedure which provides directions for installing the rear gear group components in reverse order and ensuring proper bearing placement and torque specifications are followed.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. Precise identification and reinstallation of parts is emphasized. The assembly section provides instructions for reinstalling components in reverse order and ensuring proper placement and torque of parts.
Caterpillar cat 326 f excavator (prefix ggj) service repair manual (ggj00001 ...fjsekdmmeed
This document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, springs, pistons, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the rotating group, brake piston, and head assembly.
3. Complete the assembly by installing the relief valves, spool, and tightening bolts to the specified torques.
Caterpillar cat 336 f l xe excavator (prefix mtw) service repair manual (mtw0...fjkskedmme
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence while maintaining their original positions and order for reassembly. Safety precautions are provided throughout to warn of potential spring forces or fluid containment.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjkskedmme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure, and marks should be made on lines and cylinders before removal.
Caterpillar cat 345 b excavator (prefix 6mw) service repair manual (6mw00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists the required tools and parts. The disassembly instructions include removing components like the brake cover, brake assembly, springs, gears, and barrel assembly. The assembly instructions list installing components like bushings, bearings, seals and rings in reverse order of disassembly. Safety notices are provided to keep parts clean and prevent hydraulic system contamination.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, seals, springs, and pistons.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
Caterpillar cat 336 d l excavator (prefix myg) service repair manual (myg0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel control linkage, unit injectors, water temperature regulator housing, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new cylinder head gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp0...fjkskedmme
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, pistons, barrel assembly, friction plates and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their original positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain any released fluids.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
This document provides instructions for removing and installing a flywheel on a Caterpillar D8L track-type tractor with a 3408 engine. It describes using various tools to hold the crankshaft gear and hoist the flywheel, which weighs approximately 78 kg. Detailed steps include removing bolts, installing guide bolts, and pulling the flywheel off using a hoist and link bracket tool. For installation, the instructions specify heating the ring gear, installing guide bolts in the crankshaft, and using a hoist and link bracket to position the flywheel.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 53y) service ...jfkskemwsxmdm
This document provides instructions for removing the flywheel from a Caterpillar D8L track-type tractor with a 3408 engine. The procedure involves removing bolts holding the flywheel, installing tools to secure the crankshaft gear and flywheel, and using a hoist with a link bracket tool to lift the flywheel off of mounting tools. Precautions are given to keep parts clean and prevent contamination. Diagrams illustrate the typical configuration and tool placement.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 53y) service ...fujsekfksmemf
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and adapter assemblies. The flywheel is removed by installing holding tools and using another tool attached to an overhead hoist. The installation procedure outlines reassembling the components and pressing or installing bearings back into place. Proper cleaning and lubrication of parts is emphasized.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and adapter assemblies. The flywheel is removed by installing holder tools and lifting it off with another linked tool attached to an overhead hoist. The installation procedure outlines reassembling the components and pressing or installing bearings using heat, guides, and presses. Precautions are given to keep parts clean and ensure proper positioning of gears and seals.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...gua6982552kun
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...gua6982552kun
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...ting1499041267
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...ti76cui
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. Precise identification and reinstallation of parts is emphasized. The assembly section provides instructions for reinstalling components in reverse order and ensuring proper placement and torque of parts.
Caterpillar cat 326 f excavator (prefix ggj) service repair manual (ggj00001 ...fjsekdmmeed
This document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, springs, pistons, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the rotating group, brake piston, and head assembly.
3. Complete the assembly by installing the relief valves, spool, and tightening bolts to the specified torques.
Caterpillar cat 336 f l xe excavator (prefix mtw) service repair manual (mtw0...fjkskedmme
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence while maintaining their original positions and order for reassembly. Safety precautions are provided throughout to warn of potential spring forces or fluid containment.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjkskedmme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure, and marks should be made on lines and cylinders before removal.
Caterpillar cat 345 b excavator (prefix 6mw) service repair manual (6mw00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists the required tools and parts. The disassembly instructions include removing components like the brake cover, brake assembly, springs, gears, and barrel assembly. The assembly instructions list installing components like bushings, bearings, seals and rings in reverse order of disassembly. Safety notices are provided to keep parts clean and prevent hydraulic system contamination.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, seals, springs, and pistons.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
Caterpillar cat 336 d l excavator (prefix myg) service repair manual (myg0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout.
This document provides instructions for removing and installing the cylinder head on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves removing several other components first, including the fuel filter base, governor, fuel control linkage, unit injectors, water temperature regulator housing, inlet manifold, and exhaust manifold. The cylinder head is then removed by detaching it from the cylinder block using bolts. The installation procedure provides detailed instructions for cleaning surfaces, installing a new cylinder head gasket, positioning the cylinder head, and tightening the bolts in a specific sequence and torque. Reinstalled components are also listed.
Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp0...fjkskedmme
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, pistons, barrel assembly, friction plates and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their original positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain any released fluids.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
This document provides instructions for removing and installing a flywheel on a Caterpillar D8L track-type tractor with a 3408 engine. It describes using various tools to hold the crankshaft gear and hoist the flywheel, which weighs approximately 78 kg. Detailed steps include removing bolts, installing guide bolts, and pulling the flywheel off using a hoist and link bracket tool. For installation, the instructions specify heating the ring gear, installing guide bolts in the crankshaft, and using a hoist and link bracket to position the flywheel.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 53y) service ...jfkskemwsxmdm
This document provides instructions for removing the flywheel from a Caterpillar D8L track-type tractor with a 3408 engine. The procedure involves removing bolts holding the flywheel, installing tools to secure the crankshaft gear and flywheel, and using a hoist with a link bracket tool to lift the flywheel off of mounting tools. Precautions are given to keep parts clean and prevent contamination. Diagrams illustrate the typical configuration and tool placement.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 53y) service ...fujsekfksmemf
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and adapter assemblies. The flywheel is removed by installing holding tools and using another tool attached to an overhead hoist. The installation procedure outlines reassembling the components and pressing or installing bearings back into place. Proper cleaning and lubrication of parts is emphasized.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8L track-type tractor powered by a 3408 engine. The removal procedure involves using various tools to disassemble the rear gear group components and adapter assemblies. The flywheel is removed by installing holder tools and lifting it off with another linked tool attached to an overhead hoist. The installation procedure outlines reassembling the components and pressing or installing bearings using heat, guides, and presses. Precautions are given to keep parts clean and ensure proper positioning of gears and seals.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...gua6982552kun
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...gua6982552kun
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...ting1499041267
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Caterpillar Cat 988F Series II Wheel Loader (Prefix 2ZR) Service Repair Manua...ti76cui
1. The document provides instructions for removing and installing the rear gear group and flywheel of a 988F II wheel loader powered by a 3408E engine.
2. The removal procedure involves using various tools to disassemble components like the adapter assemblies, balancer gear, idler gear, and camshaft gear.
3. The installation procedure outlines heating and pressing components, aligning parts, and torquing bolts to reassemble the rear gear group and install the flywheel.
Similar to Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 7yb) service repair manual (7yb01573 and up) (8)
New holland tt75 tractor service repair manualfjjskekfkskemf
This document is the repair manual for New Holland TT55 and TT75 tractors. It contains sections on general information, the engine, clutches, transmissions, differentials, brakes, hydraulics, steering, electrical systems, and bodywork. The sections provide specifications, repair instructions, component locations, and other technical details for servicing and repairing systems on the tractors. This repair manual is a compilation of all relevant sections organized to provide technicians with the information needed to service and repair New Holland TT55 and TT75 tractors.
New holland mz16 h zero turn lawn mower service repair manualfjjskekfkskemf
This repair manual provides information for repairing the New Holland MZ14H, MZ16H, and MZ18H zero radius tractors. The manual contains sections covering general information, the transaxle, chassis, mower decks, and electrical systems. Each manual may not contain all listed sections and each book will only include the relevant sections for the equipment covered in that book.
New holland my17 riding mower service repair manualfjjskekfkskemf
This repair manual covers New Holland garden tractors from model years 2016-2017 and 2019. It contains 7 sections on general information, model/serial numbers, greasing/lubrication, transaxles, chassis, mower decks, and electrical systems. The sections provide specifications, safety information, and repair content for the tractors.
New holland engine 8.3 l 6 cylinder, 24 valve cnh engine with high pressure c...fjjskekfkskemf
This document is a service manual that provides repair and maintenance information for New Holland 8.3 & 9.0L 6 cylinder engines with high pressure common rail fuel systems. It contains sections on the engine, fuel and injection system, air intake system, exhaust system, cooling system, lubrication system, and starting system. The manual provides specifications, torque values, service limits, repair procedures, and required special tools for servicing the engine and its components.
This document provides part numbers and descriptions for engine components of a Massey Ferguson 6497 Tier 3 tractor. It includes two pages of detailed component lists and part numbers for the engine, cylinder block, timing gear housing, crankshaft, piston, connecting rods, and valve mechanism. The lists contain over 50 individual engine parts and components.
Massey ferguson 6480 tractor (tier 3 sisu engine) service parts catalogue man...fjjskekfkskemf
This document provides parts information for a Massey Ferguson 6480 tractor with a Tier 3 Sisu engine. It includes 35 line items listing specific engine parts like the cylinder block, timing gear housing, crankshaft, pistons, and more. Each item includes the part number, quantity, description, and any applicable comments or footnotes providing additional details.
Kubota v3800 tie4 diesel engine service repair manualfjjskekfkskemf
The document provides information on safely servicing and operating diesel engines. It outlines important safety precautions including reading all instructions before starting work, parking the machine securely, disconnecting the battery, and wearing protective equipment. Specific hazards are identified such as hot surfaces that can cause burns, high pressure fuel and hydraulic lines, and toxic exhaust gases. The document emphasizes avoiding injury from these risks by taking appropriate safety measures.
Caterpillar cat d8 l track type tractor dozer bulldozer (prefix 7yb) service ...fjjskekfkskemf
The document provides instructions for disassembling and assembling a unit injector hydraulic pump. It describes 17 steps for disassembly, which include removing various parts like the pressure compensator valve, manifold, valve block, and bearings. It then describes 24 steps for assembly, covering the installation of gaskets, seals, springs, and other parts in the reverse order of disassembly. Precautions are given to keep parts clean and prevent dirt entry into the fuel system. Various tools are listed that are required for the procedures.
Caterpillar cat 416 f backhoe loader (prefix ksf) service repair manual (ksf0...fjjskekfkskemf
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 416F backhoe loader. The removal procedure involves using a valve spring compressor tool to compress the springs, remove keepers, and take out the valves. The installation procedure specifies cleaning components, lubricating valve stems, compressing springs with the tool to insert keepers, and installing the valves in the proper positions. A separate section also outlines removing and installing the engine oil filter base.
Caterpillar cat 416 series ii backhoe loader (prefix 5 pc) service repair man...fjjskekfkskemf
This document provides instructions for removing and installing the rear axle group on a 416 Series II Backhoe Loader. It describes 7 steps to remove the rear axle group, which includes disconnecting linkages, removing mounting hardware, and lowering the axle with a transmission jack. It then details 21 steps to disassemble the rear axle group and 25 steps to reassemble it, including adjusting bearing end play and differential preload.
Caterpillar cat 415 f2 il backhoe loader (prefix pf4) service repair manual (...fjjskekfkskemf
This document provides instructions for disassembling the transmission of a 415F2 IL Backhoe Loader. It describes removing various components such as the torque converter, shafts, gears, bearings, seals and other parts. Detailed illustrations and cautions are provided for safely compressing springs and removing press-fit components using the recommended tools. The multi-step process is described for disassembling the direct drive, front output shaft, rear output shaft, direct drive shaft, and reverse shaft assemblies of the transmission.
Caterpillar cat 322 l excavator (prefix 8cl) service repair manual (8cl00001 ...fjjskekfkskemf
This document provides instructions for servicing the air conditioning system on a Caterpillar 322L excavator. It describes safety precautions that must be followed when working on refrigerant systems, which can be hazardous if guidelines are not properly followed. The document outlines procedures for preparing the machine for service, recovering refrigerant, replacing components, adding new refrigerant and oil, and evacuating and charging the system. Technicians are instructed to keep the system clean and plug all openings to prevent contamination.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 322 L, 322 LN, and 322 N excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The fuel injection control linkage is then removed by taking out bolts. The installation procedure details applying lubricant to seals before reinstalling components and reconnecting linkages using the same special tools. Proper torque specifications are provided for bolts.
Caterpillar cat 320 s excavator (prefix 3 xk) service repair manual (3xk00822...fjjskekfkskemf
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes and cables from the governor, removing retaining clips and pins, and taking out bolts. For installation, the process is reversed, applying lubricant to seals, inserting pins using specialized tools, and reattaching tubes and cables. Proper cleaning and use of replacement parts is emphasized. References are provided for additional technical details.
Caterpillar cat 320 n excavator (prefix 3 xk) service repair manual (3xk00822...fjjskekfkskemf
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes and cables from the governor, removing retaining clips and pins, and taking out bolts. For installation, the process is reversed, applying lubricant to seals, inserting pins using specialized tools, and reattaching tubes and cables. Proper cleaning and use of replacement parts is emphasized. References are provided for additional technical details.
Caterpillar cat 320 l excavator (prefix 3 xk) service repair manual (3xk00822...fjjskekfkskemf
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes and cables from the governor, removing retaining clips and pins, and taking out bolts. For installation, the process is reversed, applying lubricant to seals, inserting pins using specialized tools, and reattaching tubes and cables. Proper cleaning and use of replacement parts is emphasized.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. The removal procedure involves disconnecting tubes and cables from the governor, removing retaining clips and pins, and taking out bolts. For installation, the process is reversed, applying lubricant to seals, inserting pins using specialized tools, and reattaching tubes and cables. Proper cleaning and use of replacement parts is emphasized. References are provided for additional technical details.
Case ih wd1904 tier 3 self propelled windrower service repair manual [ -yfg67...fjjskekfkskemf
This document provides service information for WD1904 and WD2304 self-propelled windrowers, including specifications for the Tier 3 engine that powers both models. The 6.7L, 6-cylinder turbocharged diesel engine produces 142 kW of power at 2200 RPM and peak torque of 830N·m at 1600 RPM for the WD1904 and 961N·m at 1600 RPM for the WD2304. The manual covers maintenance and repair procedures for the engine and various vehicle systems, with sections devoted to the engine, front and rear axles, hydrostatic drive, brakes, hydraulics, steering, electrical systems, cab, and other components.
Case ih axial flow 9240 tier 2 combine service repair manualfjjskekfkskemf
This document is a service manual for CNH America LLC's AXIAL-FLOW combines, models 7240, 8240, and 9240. It contains over 200 sections detailing the operation and maintenance of the engine, transmission, axles, hydraulics, steering, wheels, tracks, cab climate control, electrical systems, feeding, threshing, separation, and residue handling systems of the combines. Each section provides instructions and diagrams related to inspecting, repairing, and replacing components of the various combine systems.
Case ih 6130 combine service repair manualfjjskekfkskemf
This document is a service manual for CNH Industrial combine harvesters models 5130, 6130, and 7130. It contains over 200 sections covering all major vehicle systems, including the engine, transmission, axles, hydraulics, steering, brakes, electrical systems, and cab controls. Each section provides detailed information, specifications, and repair or replacement procedures for components within that system. The manual is intended to guide service technicians in maintenance and repairs.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8L TRACK-TYPE TRACTOR 7YB
Configuration: D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018
i03335401
Gear Group (Rear) - Remove
SMCS - 1206-011; 1212-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-0483(1)
Drive Plate 1
1U-5839 Bearing Puller 1
B FT-1342 Guide Bolt 2
(1)
Part of the 1P-0510 Driver Group
Start By:
a. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: There are many possible configurations of the rear gear group and flywheel housing. The
following procedure illustrates a typical example.
1. Use the following procedure for disassembly of the adapter assemblies.
1/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00586481
Typical example
a. Support adapter assembly (1) so that the gear assembly can be pressed out of the
adapter assembly. Press gear assembly (2) out of the adapter assembly.
Illustration 2 g00586630
Typical example
b. Use Tooling (A) in order to remove bearing (3) from the gear assembly.
Illustration 3 g00586904
Typical example
2/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. c. Use a press in order to remove bearing (4) from adapter assembly (1).
Illustration 4 g00586907
Typical example
d. Remove bolts (5) and ring (6) from adapter assembly (1).
e. Remove O-ring seal (7) from adapter assembly (1).
Illustration 5 g00586910
Typical example
f. If necessary, remove race (8) from adapter assembly (1).
3/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 6 g00587590
Typical example
2. With the flywheel housing in a horizontal position, remove bolts (9) from shafts (10).
Note: The bearings that are located toward the flywheel will fall when gear (11) and gear
(12) are removed. Hold these bearings in position when the gears are removed.
3. Remove balancer gear (12) and idler gear (11).
4. Use the following procedure for disassembly of balancer gear (12).
Illustration 7 g00587608
Typical example
a. Remove shaft (13), spacer (15), bearing (14), and bearing (16) from balancer gear
(12).
Illustration 8 g00587624
Typical example
b. Remove bearing cup (17) from balancer gear (12).
Note: The bearing cups will be damaged from the removal. Use new parts for
replacement.
4/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 9 g00587629
Typical example
c. Remove spacer (18) from gear (12).
d. Remove bearing cup (19).
e. If necessary, remove ring (20) from gear (12).
5. Use the procedure in Step 4 in order to disassemble idler gear (11).
Illustration 10 g01712733
6. Install Tooling (B) in the crankshaft. Remove gear (20A).
7. Remove the O-ring seal from gear (20A).
5/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 11 g00587666
Typical example
8. Remove bolts (21). Remove camshaft gear (22).
Illustration 12 g00587668
Typical example
9. If necessary, remove dowel (23).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 6 00:12:11 UTC+0800 2020
6/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8L TRACK-TYPE TRACTOR 7YB
Configuration: D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018
i03335022
Gear Group (Rear) - Install
SMCS - 1206-012; 1212-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B FT-1342 Guide Bolt 2
C 1P-0524(1)
Drive Plate 1
D 1P-0513(1)
Drive Plate 1
(1)
Part of the 1P-0520 Driver Group
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: There are many possible configurations of the rear gear group and flywheel housing. The
following procedure illustrates a typical example.
1/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 1 g00587668
Typical example
1. Install dowel (23) in the camshaft if the dowel was removed.
Illustration 2 g00587666
Typical example
2. Install camshaft gear (22) in position on the camshaft. Install four bolts (21).
Illustration 3 g01712733
3. Install the O-ring seal on gear (20A).
2/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 4. Lightly lubricate the seal on the end of the crankshaft with clean engine oil.
5. Install Tooling (B) in the crankshaft. Install gear (20A).
6. Use the following procedure for assembly of balancer gear (12).
Illustration 4 g01717018
a. Install ring (20), bearing cup (19), and spacer (18) in balancer gear (12).
Note: Spacer (18) must be installed on the deepest side of gear (12) and against ring
(20).
Illustration 5 g01712754
b. Use a press and Tooling (C) in order to install bearing cup (17). Install bearing cup
(17) on the side of the gear that is stamped with the timing mark. Bearing cup (17)
should be in contact with the spacer.
3/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 6 g00587608
Typical example
c. Install bearing (16), spacer (15), bearing (14), and shaft (13) in gear (12).
7. Use the procedure in Step 6 in order to assemble idler gear (11).
Illustration 7 g00587895
Typical example
8. Place idler gear (11) and balancer gear (12) in position on the flywheel housing. Make sure
that the oil holes in shafts (10) are in alignment with the holes that are in the flywheel
housing.
Note: Install balancer gear (12) with the timing mark toward the flywheel housing.
9. Install bolts (9).
10. Use the following procedure in order to assemble adapter assemblies (1).
4/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 8 g00586910
Typical example
a. If the bearing race was removed, install race (8). Install race (8) in adapter assembly
(1) until the race makes contact with the counterbore.
Illustration 9 g00586907
Typical example
b. Install ring (6), bolts (5), and O-ring seal (7) on adapter assembly (1).
Illustration 10 g01712644
c. Heat bearing (3) to 135 °C (275 °F) for approximately 30 minutes.
5/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. d. Install bearing (3) on gear (2) until the bearing makes contact with the counterbore.
Illustration 11 g00588013
Typical example
e. Install gear (2) and the bearing in adapter assembly (1).
Illustration 12 g01712873
f. Use a press and Tooling (D) in order to install bearing (4) in adapter assembly (1).
Install the bearing until the bearing makes contact with the counterbore.
End By:
a. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 6 00:13:10 UTC+0800 2020
6/6D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8L TRACK-TYPE TRACTOR 7YB
Configuration: D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018
i04406249
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
FT-1341 Bracket Assembly 1
1B-3623 Bolt 2
B FT-1342 Guide Bolt 2
C 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g00578443
Typical example
1. Remove six bolts (1) that hold the flywheel in position.
2. Install Tool (A) in order to hold the crankshaft gear in position.
3. Remove the remainder of bolts (1) .
Illustration 2 g00578444
Typical example
4. Install Tools (B) .
2/3D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 3 g00578445
Typical example. Tooling (C) is not the tooling called out in the Table.
5. Fasten Tool (C) to a hoist and place the tool in position in the groove of flywheel (2) .
6. Pull flywheel (2) onto Tool (A) .
7. Remove Tool (A) .
8. Remove Flywheel (2) with Tool (C) .
The weight of the flywheel is approximately 78 kg (172 lb).
9. If necessary, remove the ring gear from flywheel (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 6 00:14:09 UTC+0800 2020
3/3D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8L TRACK-TYPE TRACTOR 7YB
Configuration: D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018
i04406250
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1342 Guide Bolt 2
B 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Heat the ring gear to a maximum temperature of 300 °C (572 °F), and install the ring gear
on the flywheel. Ensure that the chamfer of the gear teeth will be toward the starter pinion
after the flywheel is installed.
1/3D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 1 g00578491
Typical example. Tooling (B) shown is not the tooling called out in the Table.
2. Install Tool (A) in the crankshaft.
3. Fasten Tool (B) to a hoist. Install the tool in the groove of flywheel (2) .
The weight of the flywheel is approximately 78 kg (172 lb).
4. Place flywheel (2) in position on Tools (A) .
Illustration 2 g00578492
Typical example
5. Apply clean engine oil or 5P-0960 Molybdenum Grease to the threads of bolts (2) .
6. Install six of the bolts.
2/3D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. 7. Remove Tools (A) and (B) .
8. Install the remainder of bolts (2) . Tighten all of the bolts to a torque of 270 ± 40 N·m (200
± 30 lb ft).
9. Check the runout of the flywheel.
Note: For information on checking for flywheel runout, refer to Testing and Adjusting,
"Flywheel-Inspect".
Note: For more detailed information regarding the flywheel, refer to Specifications, "Flywheel".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 6 00:15:09 UTC+0800 2020
3/3D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8L TRACK-TYPE TRACTOR 7YB
Configuration: D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018
i07051211
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the rear gear remains in place when the crankshaft rear seal and
crankshaft wear sleeve are removed.
1. Install two bolts from the flywheel and suitable washers through the rear gear in the
crankshaft.
1/2D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 1 g01195516
Illustration 2 g00515624
2. Use a punch or Tooling (A) to puncture a hole in seal assembly (1). Use Tooling (A) to
remove seal assembly (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 6 00:16:08 UTC+0800 2020
2/2D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8L TRACK-TYPE TRACTOR 7YB
Configuration: D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE
Disassembly and Assembly
3408E and 3412E Engines for Caterpillar Built Machines
Media Number -RENR2336-06 Publication Date -01/08/2018 Date Updated -10/08/2018
i01493839
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools for Engines with Rear Gear Train
Tool Part Number Part Description Qty
A
5P-7301 Locator 1
5P-7309 Bolt 2
5P-7310 Bolt 2
8T-2683 Seal Installer 1
9S-8858 Nut 1
Required Tools for Engines without Rear Gear Train
Tool Part Number Part Description Qty
B
5P-1733 Locator 1
5P-1737 Bolt 3
6V-6143 Seal Installer 1
9S-8858 Nut 1
NOTICE
Keep all parts clean from contaminants.
1/5D8L TRACTOR 7YB01573-UP (MACHINE) POWERED BY 3408 ENGINE(ZEBP1...
2020/1/6https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...