Caterpillar Cat D6N TRACK-TYPE TRACTOR (Prefix ALH) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
D6N TRACK-TYPE TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6N TRACK-TYPE TRACTOR ALH
Configuration: D6N XL, FTC, LGP TRACK-TYPE TRACTOR ALH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
D6N Track-Type Tractor Power Train
Media Number -RENR5267-00 Publication Date -01/04/2003 Date Updated -20/05/2003
i01917626
Steering Clutch and Brake - Disassemble
SMCS - 4100-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
Start By:
A. Separate the final drive, the steering clutch, and the brake. Refer to Disassembly and
Assembly, "Final Drive, Steering Clutch, and Brake - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/8(W)
w
2021/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Illustration 1 g00952255
1. Remove bolts (1) and plate (2) .
2. Remove sleeve bearings (3) from plate (2) .
3. Remove input hub (4) .
2/8(W)
w
2021/12/2

4. Remove clutch plates (5) and friction discs (6) from hub assembly (7) .
5. Remove piston (8) and sleeve bearing (9) from hub assembly (7) .
6. Remove seals (10) and (11) from piston (8) .
3/8(W)
w
2021/12/2

7. Turn over the hub and brake assembly. The weight of the hub and brake assembly is
approximately 127 kg (280 lb).
8. Remove ring (12) from hub assembly (7) .
9. Attach Tooling (A) and a suitable lifting device to housing (13). Remove the brake
assembly from hub assembly (7). The weight of the brake assembly is approximately 86 kg
(190 lb).
4/8(W)
w
2021/12/2

10. Remove bearing (14) from housing (13) .
11. Remove rings (15) and bearing (16) from hub assembly (7) .
Personal injury can result from parts under high spring pressure.
Spring force can cause parts to come off suddenly. Contact your
Caterpillar dealer for disassembly instructions before removing any
parts.
5/8(W)
w
2021/12/2

Note: Make sure that you remove bolts (17) before you remove bolts (19). Bolts (19) hold a
spring that is under compression.
12. Remove bolts (17) and plate (18) from housing (13) .
13. Remove brake plates (20) and friction discs (21) from the housing.
Personal injury can result from parts under high spring pressure.
Spring force can cause parts to come off suddenly. Contact your
Caterpillar dealer for disassembly instructions before removing any
parts.
6/8(W)
w
2021/12/2

Note: Make sure that you slowly loosen and evenly loosen bolts (19) .
14. Remove bolts (19) and manifold assembly (22) from housing (13) .
15. Remove seals (23) and (24) from manifold assembly (22) .
7/8(W)
w
2021/12/2

16. Remove piston (25) from housing (13) .
17. Remove springs (26) from housing (13) .
Note: Note the direction of spring (26) before removing.
18. Remove O-ring seals (27) and (28) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 2 14:17:11 UTC+0800 2021
8/8(W)
w
2021/12/2

Shutdown SIS
Previous Screen
i01917627
Steering Clutch and Brake - Assemble
SMCS - 4100-016
Assembly Procedure
Table 1
Required Tools
B 1P-0510 Driver Gp 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/8(W)
w
2021/12/2

1. Install springs (26) into housing (13) .
2. Install O-ring seals (27) and (28) .
3. Position piston (25) into housing (13) .
4. Install seals (23) and (24) on manifold assembly (22). Put clean oil on the lip of the seals.
2/8(W)
w
2021/12/2

5. Align the oil holes in manifold assembly (22) with the holes in housing (13). Install
manifold assembly (22) and bolts (19) .
6. Raise the temperature of bearing (16) and install bearing (16) onto hub assembly (7).
Bearing (16) must be seated squarely on the hub assembly after bearing (16) has cooled.
7. Install rings (15) onto hub assembly (7) .
3/8(W)
w
2021/12/2

8. Install bearing (14) into housing (13) .
9. Attach Tooling (A) and a suitable lifting device to housing (13) and lower the housing into
position on hub assembly (7) .
10. Install ring (12) onto hub assembly (7) .
4/8(W)
w
2021/12/2

11. Start with a plate and install brake plates (20) and friction discs (21). Alternate brake plates
(20) and friction discs (21) .
12. Install plate (18) and bolts (17) onto housing (13) .
5/8(W)
w
2021/12/2

13. Install sleeve bearing (9) into hub assembly (7) .
14. Install seals (10) and (11) into piston (8) .
15. Put clean oil on the seals and install piston (8) into hub assembly (7) .
6/8(W)
w
2021/12/2

16. Install input hub (4) .
17. Start with a plate and install clutch plates (5) and friction discs (6). Alternate clutch plates
(5) and friction discs (6) .
7/8(W)
w
2021/12/2

18. Install sleeve bearing (3) into plate (2) .
19. Position plate (2) onto the housing and install bolts (1) .
End By: Connect the final drive, the steering clutch, and the brake. Refer to Disassembly and
Assembly, "Final Drive, Steering Clutch, and Brake - Connect".
Thu Dec 2 14:18:07 UTC+0800 2021
8/8(W)
w
2021/12/2

Shutdown SIS
Previous Screen
i01867193
Final Drive, Steering Clutch, and Brakes - Connect
SMCS - 4050-077; 4100-077
Connection Procedure
Table 1
Required Tools
Note: Check the O-ring seal for wear or damage. Replace the O-ring seal, if necessary.
1. Install O-ring seal (3) onto steering clutches and brakes (1) .
2. Position steering clutches and brakes (1) onto the final drive. The weight of steering
clutches and brakes (1) is approximately 181 kg (400 lb).
1/2(W)
w
2021/12/2

3. Install bolts (2) .
4. Remove Tooling (A) and the lifting device from steering clutches and brake (1) .
End By: Install the final drive, the steering clutch, and the brake. Refer to Disassembly and
Assembly, "Final Drive, Steering Clutch, and Brakes - Install".
Thu Dec 2 14:19:02 UTC+0800 2021
2/2(W)
w
2021/12/2

Shutdown SIS
Previous Screen
i01896607
Final Drive, Steering Clutch and Brake - Install
SMCS - 4050-012; 4100-012
Installation Procedure
Table 1
Required Tools
A
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
9S-9076 Spacer 1
7X-2557 Bolt 2
1/4(W)
w
2021/12/2

1. Install O-ring seals (7) .
2. Adjust bracket (1) until Dimension (X) is equal to 55 mm (2.0 inch).
3. Attach Tooling (A) and a suitable lifting device to final drive (3) .
2/4(W)
w
2021/12/2

4. Position final drive (3). The weight of final drive (3) is approximately 590 kg (1300 lb).
7. Remove Tooling (A) .
3/4(W)
w
2021/12/2

End By:
a. Install the axle. Refer to Disassembly and Assembly, "Axle - Install".
b. Connect the track. Refer to Disassembly and Assembly, "Track - Connect".
Thu Dec 2 14:19:58 UTC+0800 2021
4/4(W)
w
2021/12/2

Shutdown SIS
Previous Screen
i07005964
Final Drive Planetary Carrier (In Chassis) - Remove
SMCS - 4092-011
Removal Procedure
Table 1
Required Tools
A
123-4370 Stud Puller 3
6V-7742 Full Nut 3
B 138-7574 Link Bracket 1
C
143-5455 Lifting Bracket 1
189-0411 Shackle As 1
D 1P-0074 Slide Hammer Puller Gp 1
Start By:
a. Remove the outer axle shafts. Refer to Disassembly and Assembly, "Axle Shaft - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2021/12/2

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the final drive into a suitable container for storage or disposal. Refer to
Operation and Maintenance, "Final Drive Oil - Change".
2. Remove bolts (1). Block sprocket segment (2) with suitable cribbing.
3. Install Tooling (A). Remove bolts (3). Slide final drive planetary carrier (4) to the end of
Tooling (A).
2/4(W)
w
2021/12/2

4. Attach Tooling (B) and a suitable lifting device to final drive planetary carrier (4). Apply
tension.
5. Remove the nuts from Tooling (A) and remove final drive planetary carrier (4). The weight
of final drive planetary carrier (4) is approximately 100 kg (220 lb). Remove the O-ring seal
from final drive planetary carrier (4).
6. Remove bolts (5) and retainer (6).
3/4(W)
w
2021/12/2

7. Use Tooling (C) to remove ring gear (7). The weight of ring gear (7) is approximately 41 kg
(90 lb).
8. Use Tooling (D) (not shown) to remove seal (9).
Thu Dec 2 14:20:54 UTC+0800 2021
4/4(W)
w
2021/12/2

Shutdown SIS
Previous Screen
i07011911
Final Drive Planetary Carrier (In Chassis) - Install
SMCS - 4092-012
Installation Procedure
Table 1
Required Tools
A
123-4370 Stud Puller 3
6V-7742 Full Nut 3
B 138-7574 Link Bracket 1
C
143-5455 Lifting Bracket 1
189-0411 Shackle As 1
E 1P-0520 Driver Gp 1
1/4(W)
w
2021/12/2

1. Use Tooling (E) (not shown) to install seal (9) to Dimension (X). Dimension (X) is
9 ± 0.25 mm (0.3543 ± 0.0098 inch).
2/4(W)
w
2021/12/2

2. Use Tooling (C) to install ring gear (7). The weight of ring gear (7) is approximately 41 kg
(90 lb).
3. Install retainer (6) and bolts (5). Tighten bolts (5) to a torque of 122 ± 20 N·m
(90 ± 15 lb ft).
4. Install the O-ring seal on final drive planetary carrier (4).
5. Install Tooling (B) on final drive planetary carrier (4).
6. Use Tooling (B) to position final drive planetary carrier (4) on Tooling (A). Install the nuts
on Tooling (A). The weight of final drive planetary carrier (4) is approximately 100 kg
(220 lb). Remove Tooling (B).
3/4(W)
w
2021/12/2

7. Install final drive planetary carrier (4). Install bolts (3). Remove Tooling (A).
8. Install bolts (1). Remove the cribbing from sprocket segment (2).
9. Fill the oil in the final drive. Refer to Operation and Maintenance, "Final Drive Oil -
Change".
End By:
a. Install the outer axle shafts. Refer to Disassembly and Assembly, "Axle Shaft - Remove".
Thu Dec 2 14:21:49 UTC+0800 2021
4/4(W)
w
2021/12/2

Shutdown SIS
Previous Screen
i01896904
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
A
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
9S-9076 Spacer 1
7X-2557 Bolt 2
Start By:
a. Separate the track. Refer to Disassembly and Assembly, "Track - Seperate".
b. Remove the axle. Refer to Disassembly and Assembly, "Axle - Remove".
1/3(W)
w
2021/12/2

1. Adjust bracket (1) until Dimension (X) is equal to 80 mm (3.0 inch).
2. Remove bolts (2).
3. Attach Tooling (A) and a suitable lifting device to final drive (3).
2/3(W)
w
2021/12/2

4. Remove bolts (4) and bolts (5).
5. Remove final drive (3). The weight of final drive (3) is approximately 408 kg (900 lb).
Thu Dec 2 14:22:45 UTC+0800 2021
3/3(W)
w
2021/12/2

Shutdown SIS
Previous Screen
i06691352
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
B 1P-0074 Slide Hammer Puller Gp 1
C
FT-1934 Puller Beam 1
- (16 mm x 190.5 mm) Bolt 4
5P-8247 Hard Washer 4
6V-3170 Double Acting Cylinder 1
9U-6600 Hand Hydraulic Pump 1
1P-0521 Driver Group 1
D 439-3940 Bracket As 2
Start By:
a. Remove the final drive.
1/6(W)
w
2021/12/2

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

1. Attach Tooling (A) and a suitable lifting device to carrier (1). The weight of carrier (1) is
approximately 50 kg (110 lb).
2. Remove bolts (2) and carrier (1) from sprocket hub (3). Position carrier (1) onto suitable
cribbing.
3. Remove bolt (4), the washer, the retainer, and the O-ring seal from carrier (1).
4. Use a suitable press to remove shaft (5) from carrier (1).
5. Repeat Steps 3 and 4 for the remaining shafts.
2/6(W)
w
2021/12/2

Caterpillar Cat D6N TRACK-TYPE TRACTOR (Prefix ALH) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

More from ufjsekdm8id

More from ufjsekdm8id (20)

Recently uploaded

Recently uploaded (19)

Caterpillar Cat D6N TRACK-TYPE TRACTOR (Prefix ALH) Service Repair Manual Instant Download.pdf