1) The documents provide instructions for removing, disassembling, assembling, and installing various fuel system components on a C18 Industrial Engine, including the fuel priming pump, fuel filter base, and fuel transfer pump.
2) The procedures describe disconnecting hoses, removing bolts, and taking out individual parts like O-rings, valves, and fittings.
3) Safety notices emphasize the importance of cleanliness and containing fluids to prevent contamination and environmental damage.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02536739
Fuel Priming Pump - Remove and Install
SMCS - 1258-010
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Turn the fuel supply to the “OFF” position.
1/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01049296
2. Remove bolts (2). Remove fuel priming pump assembly (1) from fuel filter base (4).
3. Remove gasket (3) from the fuel priming pump assembly and the fuel filter base.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g01049296
1. Position gasket (3) on fuel filter base (4).
2. Position fuel priming pump assembly (1) on the fuel filter base and install bolts (2).
3. Turn the fuel supply to the “ON” position.
4. Remove the air from the system. Refer to Testing and Adjusting, "Fuel System - Prime".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:42:04 UTC+0800 2020
3/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02163698
Fuel Filter Base - Remove
SMCS - 1262-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
1/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Contaminants may cause rapid wear and shortened component life.
1. Turn the fuel supply to the “OFF” position.
Illustration 1 g01097235
2. Disconnect harness assembly for fuel pressure sensor (1). Disconnect harness assembly for
fuel temperature sensor (2).
3. Disconnect hose assembly (5). Disconnect hose assembly (6). Disconnect hose assembly
(4).
4. Use Tooling (A) to remove fuel filter (7).
5. Remove bolts (3). Remove fuel filter base (8).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:43:00 UTC+0800 2020
2/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02086029
Fuel Filter Base - Disassemble
SMCS - 1262-015
Disassembly Procedure
Start By:
a. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g01063845
1. Remove fuel bypass valve (2) from fuel filter base assembly (1). Remove the O-ring seals
from the fuel bypass valve.
2. Remove fuel check valve (5) from fuel filter base assembly (1). Remove the O-ring seals
from the fuel check valve.
3. Remove fitting (3) from fuel filter base assembly (1). Remove the O-ring seals from the
fitting.
4. If necessary, remove hollow stud (4) from fuel filter base assembly (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:43:55 UTC+0800 2020
2/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i03998661
Fuel Filter Base - Assemble
SMCS - 1262-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-0695 Thread Lock Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 1 g01063845
1. Install the O-ring seals on fuel bypass valve (2) . Install the fuel bypass valve in fuel filter
base assembly (1) .
2. Install the O-ring seals on fuel check valve (5) . Install the fuel check valve in fuel filter
base assembly (1) . Tighten the fuel check valve to a torque of 28 ± 3 N·m (21 ± 2 lb ft).
3. Install the O-ring seals on fitting (3) . Install the fitting in fuel filter base assembly (1) .
4. If necessary, install hollow stud (4) to fuel filter base assembly (1) . Tighten the hollow stud
to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
Note: Apply Tooling (A) to the first 7.6 ± 0.8 mm (0.30 ± 0.03 inch) of threads at the base
end of the taperlock stud.
End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:44:51 UTC+0800 2020
2/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02163737
Fuel Filter Base - Install
SMCS - 1262-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01097235
1/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 1. Position fuel filter base (8) and install bolts (3).
2. Connect hose assembly (5). Connect hose assembly (6). Connect hose assembly (4).
3. Install fuel filter (7). Follow the directions on the fuel filter for the correct installation
procedure. Do not overtighten the fuel filter.
4. Connect harness assembly for fuel pressure sensor (1). Connect harness assembly for fuel
temperature sensor (2).
5. Turn the fuel supply to the “ON” position.
6. Remove the air from the system. Refer to Testing and Adjusting, "Fuel System - Prime".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:45:47 UTC+0800 2020
2/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02014217
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Turn the fuel supply to the “OFF” position.
1/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g01041378
2. Disconnect hose assembly (2) and hose assembly (3) from the fuel transfer pump.
3. Remove bolts (4).
4. Remove fuel transfer pump (1) from the adapter.
5. Remove O-ring seal (5) from fuel transfer pump (1).
6. Remove bolts (7). Remove cover (6) from the front housing. Remove O-ring seal (8) from
the cover.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:46:43 UTC+0800 2020
2/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02014219
Fuel Transfer Pump - Install
SMCS - 1256-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-0695 Thread Lock Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g01041378
1. Install O-ring seal (5) on fuel transfer pump (1). Lubricate the O-ring seal with clean engine
oil.
2. Position fuel transfer pump (1) in the adapter. Install bolts (4).
3. Connect hose assembly (2) and hose assembly (3) to the fuel transfer pump.
4. Install O-ring seal (8) on cover (6). Lubricate the O-ring seal with clean engine oil.
5. Put cover (6) in position on the front housing. Apply Tooling (A) on bolts (7). Install bolts
(7) and tighten to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
6. Turn the fuel supply to the “ON” position.
7. Remove the air from the fuel system. Refer to Testing and Adjusting, "Fuel System -
Prime".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:47:38 UTC+0800 2020
2/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02954356
Electronic Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5F-4764 Pry Bar 1
Start By:
A. Remove the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 1 g01150587
1. Disconnect harness assembly (1) .
Note: Note the orientation of the bridge assemblies for installation purposes.
2. Remove bridge assemblies (3) .
NOTICE
If the injector hold down bolt is loose during the removal procedure,
inspect the injector bore for wear and debris. Replace the clamp and
spacer.
3. Remove bolt (4) , spacer (5) , and clamp (6) .
4. Place an identification mark on electronic unit injectors (2) for installation purposes. Each
electronic unit injector (2) must be reinstalled in the original location in the cylinder head.
2/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 2 g01073439
5. Use Tooling (A) to pry beneath the base and free electronic unit injector (2) .
6. Remove electronic unit injector (2) from the cylinder head.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:48:34 UTC+0800 2020
3/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i07537531
Electronic Unit Injector - Install
SMCS - 1290-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B - Loctite LB 8028 Camshaft Lube -
C
1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle -
4C-4057
Tube
7.9 mm (0.31 inch) OD
-
D 4C-5552 Large Bore Brush 1
E 4C-6774 Vacuum Gun Kit 1
F 8T-7765 Surface Reconditioning Pad -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 1. Use Tooling (C) to remove the fuel and oil from the cylinder. Evacuate as much fuel and oil
as possible from the cylinder before installing the electronic unit injector. Several
evacuations may be necessary.
2. Use Tooling (D) to clean the carbon deposit from the inside of the electronic unit injector
sleeve. Tooling (E) is available to clean loose material from the bore of the electronic unit
injector sleeve and the cylinder.
3. Use Tooling (F) to clean the carbon from the seat area that is inside of the electronic unit
injector sleeve.
4. Install the O-ring seals on the electronic unit injector. Lubricate the top two O-ring seals
with a 50/50 mixture of clean engine oil and Tooling (B).
Illustration 1 g01150587
NOTICE
When an electronic unit injector is replaced, the new electronic
injector code must be programmed into the engine's personality
module software by using the calibration menu on the Electronic
Service Tool. If the new electronic injector code is not entered, the
characteristics of the previous electronic unit injector is assumed.
If it is not possible to immediately reprogram the electronic injector
code into the personality module software, the engine will not be
severely harmed. The new electronic injector code should be
reprogrammed as quickly as possible in order to optimize engine
performance.
5. Install electronic unit injector (2) into the original location in the cylinder head.
2/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Note: Use new bolt (4).
6. Install spacer (5), clamp (6), and bolt (4). Tighten bolt (4) to a torque of 55 ± 10 N·m
(41 ± 7 lb ft).
7. Install bridge assemblies (3) in the orientation that was noted during removal.
8. Connect harness assembly (1) on electronic unit injector (2). Tighten the nuts to a torque of
2.5 ± 0.25 N·m (22 ± 2 lb in).
9. Remove the air from the fuel system. Refer to Testing and Adjusting, "Fuel System -
Prime".
End By:
a. Install the rocker arms and the rocker arm shaft. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:49:30 UTC+0800 2020
3/3(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE GJE
Configuration: C18 Industrial Engine GJE00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -RENR8630-07 Publication Date -01/11/2017 Date Updated -15/11/2017
i02169626
Electronic Unit Injector Sleeve - Remove
SMCS - 1713-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
Start By:
a. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Drain the coolant from the engine. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Change".
1/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 1 g01076133
2. Install Tooling (A) in electronic unit injector sleeve (1).
3. Tighten the nut on Tooling (A) until the electronic unit injector sleeve is pulled free of the
cylinder head.
4. Remove O-ring seals (2) and O-ring seal (3) from electronic unit injector sleeve (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jun 16 07:50:26 UTC+0800 2020
2/2(W)
w
2020/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...