In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992K WHEEL LOADER 880
Configuration: 992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine
Disassembly and Assembly
854K Wheel Dozer and 992K Wheel Loader Power Train
Media Number -KENR7587-01 Publication Date -01/09/2011 Date Updated -30/05/2018
i04350792
Torque Converter (Lockup) - Disassemble
SMCS - 3101-015-L7
S/N - 8801-UP
S/N - ZMX1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 154-6183 Forcing Bolt 2
B 138-7574 Link Bracket 2
C 138-7573 Link Bracket 3
D 154-6184 Forcing Bolt 3
E 5J-0490 Forcing Bolt 2
F
0S-1614 Bolt 1
5P-0537 Hard Washer 1
G
9X-8876 Bolt 2
1F-7958 Nut 2
H 138-7575 Link Bracket 3
J 2D-1201 Eyebolt 1
K 1P-0520 Driver Gp
1/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Start By:
a. Remove the torque converter.
b. Remove the torque converter lockup clutch modulating valve.
c. Remove the torque converter impeller clutch modulating valve.
d. Remove the torque converter outlet relief valve.
e. Remove the torque converter priority valve.
f. Remove the transmission pump.
g. Remove the steering piston pump.
h. Remove the brake piston pump.
i. Remove the right-hand implement piston pump.
j. Remove the center implement piston pump.
k. Remove the hydraulic fan piston pump.
1. Position the torque converter housing assembly onto suitable cribbing. The weight of the
torque converter housing assembly is approximately 1250 kg (2850 lb).
Illustration 1 g02505643
2. Remove bolt (2), retainer (3), and yoke (1).
2/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g02505758
3. Remove O-ring seal (4) from yoke (1).
Illustration 3 g01450186
4. Remove bolts (6) and bolts (10).
5. Remove bolts (7), manifold (8), and the O-ring seals.
6. Remove orifice plug (9) (not shown) and the O-ring seal.
7. Install Tooling (A). Use Tooling (A) in order to separate pump adapter (5) from housing
assembly (11).
3/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g01450226
8. Attach Tooling (B) and a suitable lifting device to pump adapter (5). The weight of pump
adapter (5) is approximately 50 kg (110 lb). Use Tooling (B) and the suitable lifting device
in order to remove pump adapter (5) from housing assembly (11).
Illustration 5 g01450322
9. Remove lip seal (13), bearing cup (12), and O-ring seals (14) from pump adapter (5).
Illustration 6 g01450328
10. Use two people in order to remove idler gear (15). The weight of idler gear (15) is
approximately 36 kg (80 lb).
4/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g01450330
11. Remove bearing cones (16) from idler gear (15).
Illustration 8 g01450331
12. Remove bearing cup (17) from housing assembly (11).
Illustration 9 g01450350
13. Attach Tooling (B), Tooling (C), and a suitable lifting device to housing assembly (11). The
weight of housing assembly (11) is approximately 680 kg (1500 lb).
5/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Install Tooling (D) to housing assembly (11). Use Tooling (D) in order to separate housing
assembly (11) from the torque converter assembly.
15. Use Tooling (B), Tooling (C), and the suitable lifting devices in order to remove housing
assembly (11).
Illustration 10 g00357394
16. Position housing assembly (11) onto the opposite side and remove O-ring seal (18).
Illustration 11 g02513099
17. Remove bolts (19) and adapter (20) from housing assembly (11). Remove O-ring seal (21)
(not shown).
18. Remove bolts (22).
19. Install Tooling (A) in order to separate pump adapter (23) from housing assembly (11).
6/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01450400
20. Attach Tooling (B) and a suitable lifting device to pump adapter (23). The weight of pump
adapter (23) is approximately 50 kg (110 lb). Use Tooling (B) and the suitable lifting device
in order to remove pump adapter (23). Remove shims (24).
Illustration 13 g01450423
21. Remove bearing cup (25) and O-ring seal (26) from pump adapter (23).
Illustration 14 g01450430
22. Use two people in order to remove pump drive gear (27) from housing assembly (11). The
weight of pump drive gear (27) is approximately 27 kg (60 lb).
7/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01450567
23. Remove retaining ring (29), spline adapter (30), and the O-ring seal from pump drive gear
(27). Remove bearing cones (28).
24. Repeat Steps 18 through 23 in order to remove the remaining pump adapter.
Illustration 16 g01450584
25. Position torque converter assembly (33), as shown. The weight of torque converter
assembly (33) is approximately 590 kg (1300 lb). Remove bolts (31). Install Tooling (E).
Use Tooling (E) in order to separate pilot guide (32) from torque converter assembly (33).
Remove pilot guide (32).
8/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00357612
26. Position torque converter assembly (33), as shown.
27. Remove bolts (34), retainer (35), and washer (36) (not shown).
Illustration 18 g00357633
28. Remove bolts (37).
Illustration 19 g01450614
29. Attach Tooling (C) to clutch housing assembly (38). The weight of clutch housing assembly
(38) is approximately 168 kg (370 lb). Install Tooling (F) in order to prevent the turbine
assembly from separating from the bearing. Remove clutch housing assembly (38).
9/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g01450725
34. Remove discs (48) and the plate.
35. Remove Tooling (F) from the turbine hub. Remove turbine hub assembly (49).
Illustration 24 g00358256
36. Remove race (51). Remove seal carrier (52) and seal (53). Remove sleeve bearing (50).
Illustration 25 g01450731
37. Remove piston (54) and the seals. Remove sleeve (55). Remove bearing (56) and race (57)
from clutch housing assembly (38).
11/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00358264
38. Remove retaining ring (60) and thrust bearing (59). Remove the carrier and stator assembly
(58).
Illustration 27 g01451954
Illustration 28 g01452159
39. Remove retaining ring (63).
40. If necessary, position stator assembly (58) and carrier (62) onto a suitable press. Use
Tooling (K) and the suitable press in order to remove carrier (62) from stator assembly (58).
Remove plate (61). Remove plate (65) (not shown).
41. Remove retaining ring (64) (not shown).
12/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g01452183
42. Install Tooling (G) in order to hold housing assembly (68) to the backing plate. Attach
Tooling (H) and a suitable lifting device to the backing plate. The combined weight of
housing assembly (68), impeller clutch (67), and the backing plate is approximately 181 kg
(400 lb). Remove housing assembly (68), impeller clutch (67), and the backing plate from
shaft assembly (66).
Illustration 30 g01452223
43. Remove thrust bearing (71), sleeve (72), and pins (73).
44. Attach Tooling (C) and a suitable lifting device to impeller hub (70). The combined weight
of impeller (69) and impeller hub (70) is approximately 57 kg (125 lb). Remove impeller
(69) and impeller hub (70) from housing assembly (68).
13/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 31 g01452231
45. Remove plate (74). If necessary, remove four dowel pins (75) (not shown). Remove twelve
bolts (76) (not shown). Remove sleeve bearing (77). Use two people in order to remove
adapter (78). The weight of adapter (78) is approximately 25 kg (55 lb).
Illustration 32 g01452240
46. Remove impeller hub (70) from impeller (69).
Illustration 33 g01452246
47. Remove Tooling (G).
48. Attach Tooling (C) and a suitable lifting device to backing plate (79). The weight of backing
plate (79) is approximately 25 kg (55 lb). Remove backing plate (79) from housing
assembly (68).
14/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 37 g01452264
52. Remove thrust washer (84). Remove plate (85) (not shown) and two dowel pins (86) (not
shown) that are located under thrust washer (84).
Illustration 38 g01452270
53. Remove bolts (87). Use two people in order to remove gear (88) and gear (89) as one unit.
The combined weight of gear (88) and gear (89) is approximately 36 kg (80 lb). Remove
bearing race (90) from gears (88) and (89).
Illustration 39 g01452280
54. Remove seals (91) and seals (94).
16/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 55. Drive in locator pin (93) in order to remove seal carrier (94). Remove bearing (95) from
carrier assembly (96).
Illustration 40 g02506758
56. Reposition carrier assembly (96), as shown. The weight of carrier assembly (96) is
approximately 79 kg (175 lb).
57. Remove bolts (97) and bearing cage (98) from carrier assembly (96).
58. Remove lip seal (99) from bearing cage (98).
Illustration 41 g02506779
59. Attach Tooling (J) and a suitable lifting device to shaft assembly (66). The weight of shaft
assembly (66) is approximately 26 kg (57 lb). Remove shaft assembly (66) from carrier
assembly (96). Remove gasket (100).
17/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 42 g02506796
60. Remove seals (105) and seal carrier (104). Remove bearing (103) from shaft (106). Remove
seal (102) and seal carrier (101).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 13 14:32:55 UTC+0800 2021
18/18
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 992K WHEEL LOADER 880
Configuration: 992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine
Disassembly and Assembly
854K Wheel Dozer and 992K Wheel Loader Power Train
Media Number -KENR7587-01 Publication Date -01/09/2011 Date Updated -30/05/2018
i04351631
Torque Converter (Lockup) - Assemble
SMCS - 3101-016-L7
S/N - 8801-UP
S/N - ZMX1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 138-7574 Link Bracket 2
C 138-7573 Link Bracket 3
F
0S-1614 Bolt 1
5P-0537 Hard Washer 1
G
9X-8876 Bolt 2
1F-7958 Nut 2
H 138-7575 Link Bracket 3
J 2D-1201 Eyebolt 1
K 1P-0520 Driver Gp 1
L 8T-5096 Dial Indicator Gp 1
M 5P-2390 Gauge Tool Gp 1
1. Apply oil to all of the bearings before assembly.
1/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g02506796
2. Raise the temperature of seal carrier (101). Install seal carrier (101) onto shaft (106).
3. Lubricate seal (102) with the oil that is being sealed. Install seal (102) on seal carrier (101).
4. Raise the temperature of bearing (103). Install bearing (103) onto shaft (106).
5. Raise the temperature of seal carrier (104). Install seal carrier (104) onto shaft (106).
6. Lubricate seals (105) with the lubricant that is being sealed. Install seals (105) onto seal
carrier (104).
Illustration 2 g02506779
7. Attach Tooling (J) and a suitable lifting device to shaft assembly (66). The weight of shaft
assembly (66) is approximately 26 kg (57 lb). Use Tooling (J) and the suitable lifting device
in order to install shaft assembly (66) onto carrier assembly (96). Install gasket (100).
2/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 3 g02506758
8. Reposition carrier assembly (96). The combined weight of carrier assembly (96) and the
shaft assembly is approximately 34 kg (75 lb).
9. Install lip seal (99) into bearing cage (98). Position bearing cage (98). Install bolts (97).
Tighten bolts (97) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 4 g01452280
Illustration 5 g01127577
3/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 10. Reposition carrier assembly (96). The weight of carrier assembly (96) is approximately
79 kg (175 lb). Raise the temperature of bearing (95). Install bearing (95) onto carrier
assembly (96).
11. Raise the temperature of seal carrier (92). Install seal carrier (92).
Note: Make sure that the Holes (X) in seal carrier (92) are in alignment with Holes (Y) in
the shaft.
12. Install locator pin (93).
13. Install seals (91) and (94).
Illustration 6 g01452270
14. Install bearing race (90) in gear (88) and gear (89). Use two people in order to install gears
(89) and (88). The combined weight of gear (88) and gear (89) is approximately 36 kg
(80 lb). Install bolts (87). Tighten bolts (87) to a torque of 240 ± 25 N·m (175 ± 18 lb ft).
Illustration 7 g01452264
15. Install two dowel pins (86) (not shown). Install plate (85) (not shown). Install thrust washer
(84).
4/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 8 g01452258
16. Lubricate seals (83) with oil that is being sealed. Install seals (83).
Illustration 9 g01452251
17. Install piston (82).
Illustration 10 g01452249
18. Install discs (80) and plates (81).
5/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 11 g01452246
19. Attach Tooling (C) and a suitable lifting device to backing plate (79). The weight of backing
plate (79) is approximately 25 kg (55 lb). Install backing plate (79) onto housing assembly
(68).
Illustration 12 g01452240
20. Install impeller hub (70) on impeller (69).
Illustration 13 g01452231
21. Install sleeve bearing (77).
6/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 22. Use two people in order to install adapter (78). The weight of adapter (78) is approximately
25 kg (55 lb). Install twelve bolts (76) (not shown). Tighten bolts (76) to a torque of
120 ± 15 N·m (89 ± 11 lb ft).
23. Install four dowel pins (75) (not shown) that are located under plate (74). The correct height
for dowel pins (75) is 3.10 ± 0.13 mm (0.122 ± 0.005 inch). Install plate (74).
Illustration 14 g01452223
24. Install pins (73) and sleeve (72). Install thrust bearing (71).
25. Attach Tooling (C) and a suitable lifting device to impeller hub (70). The combined weight
of impeller (69) and impeller hub (70) is approximately 57 kg (125 lb). Align the splines
and install impeller (69) and impeller hub (70) on housing assembly (68).
Illustration 15 g01452183
26. Install Tooling (G) in order to hold housing assembly (68) to the backing plate. Attach
Tooling (H) and a suitable lifting device to the backing plate. The combined weight of
housing assembly (68), impeller clutch (67), and the backing plate is approximately 181 kg
(400 lb). Install housing assembly (68), impeller clutch (67), and the backing plate onto
shaft assembly (66).
27. Remove Tooling (G) that held housing (68) to the backing plate.
7/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 16 g01452445
Illustration 17 g01452159
28. Install retaining ring (64) (not shown).
29. Lower the temperature of carrier (62). Use Tooling (K) and a suitable press in order to
install carrier (62) into stator assembly (58).
30. Install plate (65) (not shown). Install plate (61). Install retaining ring (63).
8/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 18 g00358264
31. Install the carrier and stator assembly (58). Install thrust bearing (59) and retaining ring
(60).
Illustration 19 g01450731
32. Install sleeve (55).
33. Install race (57) and bearing (56).
34. Install the seals and piston (54) from the bottom side of clutch housing assembly (38).
Illustration 20 g00358256
9/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEBP5...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 35. Install sleeve bearing (50).
36. Install seal carrier (52) and seal (53).
37. Install race (51).
Illustration 21 g01450725
38. Install turbine hub assembly (49). Install Tooling (F) in order to hold the turbine assembly
together. Refer to Illustration 25 below.
39. Install discs (48) and the plate.
Illustration 22 g01450721
40. Install backing plate (47). Install retainer plates (46) and bolts (45). Tighten bolts (45) to a
torque of 50 ± 7 N·m (37 ± 5 lb ft).
10/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 23 g01450685
41. Install turbine (44). Install clamping plate (43) and bolts (42). Tighten bolts (42) to a torque
of 120 ± 15 N·m (89 ± 11 lb ft).
Illustration 24 g00357638
Illustration 25 g01450614
42. Install pins (39), sleeve (40) and bearing race (41). Reposition clutch assembly (38) onto the
opposite side for assembly purposes. The weight of clutch assembly (38) is approximately
168 kg (370 lb).
11/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. 43. Attach Tooling (C) and a suitable lifting device to clutch assembly (38). Install clutch
assembly (38). Remove Tooling (F) that is used to prevent the turbine assembly from
separating away from the bearing.
Illustration 26 g00357633
44. Install bolts (37). Tighten bolts (37) to a torque of 120 ± 15 N·m (89 ± 11 lb ft).
Illustration 27 g00357612
45. Install washer (36) (not shown), retainer (35), and bolts (34) onto torque converter assembly
(33). Tighten bolts (34) to a torque of 120 ± 15 N·m (89 ± 11 lb ft).
Illustration 28 g01451779
12/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. 46. Position torque converter assembly (33), as shown. The weight of torque converter
assembly (33) is approximately 590 kg (1300 lb). Install pilot guide (32) on torque
converter assembly (33). Install bolts (31). Tighten bolts (31) to a torque of 120 ± 15 N·m
(89 ± 11 lb ft).
Illustration 29 g01450567
47. Install spline adapter (30), the O-ring seal, bearing cones (28) and retaining ring (29) onto
pump drive gear (27).
Illustration 30 g01450430
48. Use two people in order to install pump drive gear (27). The weight of pump drive gear (27)
is approximately 27 kg (60 lb). Install all of the shims.
13/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 31 g01453045
49. Lower the temperature of bearing cup (25). Install bearing cup (25) into pump adapter (23).
Note: Do not install the seals for the pump adapters at this time.
Illustration 32 g01451567
50. Attach Tooling (B) and a suitable lifting device to pump adapter (23). Install pump adapter
(23) and bolts (22). Tighten bolts (22) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
51. When possible, rotate either the torque converter or the outer housing in order to ensure that
the bearings are properly seated.
Illustration 33 g01452534
52. Use Tooling (L) and Tooling (M) in order to check bearing end play. The bearing end play
must be 0.10 ± 0.05 mm (0.004 ± 0.002 inch). Remove the shims that were installed in Step
48 in order to obtain the correct bearing end play, as needed.
53. Remove the pump adapter from the housing assembly.
14/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
34. Illustration 34 g01451591
54. Install O-ring seals (26) onto pump adapter (23).
Illustration 35 g01451609
55. Install the correct number of shims (24) onto the housing assembly. The correct number of
shims (24) were determined in Step 52.
56. Use Tooling (B) and a suitable lifting device in order to install pump adapter (23) on the
housing assembly. Install bolts (22). Tighten bolts (22) to a torque of 240 ± 40 N·m
(177 ± 30 lb ft).
57. When possible, rotate either the torque converter housing or the outer housing in order to
ensure that the bearings are properly seated. Use Tooling (L) and Tooling (M) in order to
recheck the bearing end play. Repeat the above procedures, if necessary.
58. Repeat Steps 48 through 56 in order to install the remaining pump adapter.
15/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
35. Illustration 36 g00357394
59. Install O-ring seal (18). Turn housing assembly (11) onto the opposite side. The weight of
housing assembly (11) is approximately 680 kg (1500 lb).
Illustration 37 g00357392
60. Lower the temperature of bearing cup (17). Install bearing cup (17) in the housing assembly.
Illustration 38 g01451665
61. Attach Tooling (B), Tooling (C), and a suitable lifting device to housing assembly (11). The
weight of housing assembly (11) is approximately 680 kg (1500 lb). Install housing
assembly (11) onto the torque converter. Install bolts (10).
16/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
36. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
37. Illustration 39 g01450330
62. Lubricate bearing cones (16) with the oil that is being sealed. Install bearing cones (16) onto
idler gear (15).
Illustration 40 g01450328
63. Use two people in order to install idler gear (15) and the shim pack. The weight of idler gear
(15) is approximately 36 kg (80 lb).
Illustration 41 g01451687
64. Lower the temperature of bearing cup (12). Install bearing cup (12) into pump adapter (5).
17/21
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine(SEB...
2021/6/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...