This document provides instructions for disassembling and assembling the torque converter and transmission of a 972M wheel loader. It describes 42 steps to disassemble the torque converter, removing components like seals, springs, and gears. It then describes 6 steps to separate the transmission from the output transfer gears, removing bolts and disconnecting harnesses. Finally, it lists 21 steps to disassemble the transmission planetary, starting with removing an O-ring seal and drive gear from the input shaft. Detailed illustrations accompany each step to ensure proper reassembly.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a Caterpillar 966M Wheel Loader. It describes 43 steps for assembling the torque converter, including installing bearings, seals, springs, and other parts. It also describes 3 steps for separating the transmission from the output transfer gears, including removing bolts and disconnecting harness assemblies. Tools including lifting eyes and forcing screws are required. Safety notices are provided regarding keeping parts clean and preventing injury when handling spring-loaded components.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including links, brackets, and a transmission repair stand are required.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including links, brackets, and a transmission repair stand are required.
The document provides step-by-step instructions for assembling a torque converter for a 982M wheel loader. It lists 51 steps to install various components like seals, bearings, gears, plates and bolts. Tools required include link brackets, dial indicators, drivers and guide studs. Temperatures must be controlled for some components during installation. The assembly is completed by connecting the torque converter to the transmission and output transfer gears.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
The document provides step-by-step instructions for assembling a torque converter for a 982M wheel loader. It lists 51 steps to install various components like seals, bearings, gears, plates, and bolts. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Precautions are given for heating/cooling components and proper torque values.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
The document provides step-by-step instructions for assembling a torque converter for a 982M wheel loader. It lists 51 steps to install various components like seals, bearings, gears, plates, and bolts. Tools required include link brackets, dial indicators, drivers, and retaining ring pliers. Temperatures must be carefully controlled for some components. The assembly is completed by connecting the fully assembled torque converter to the transmission and output transfer gears.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a Caterpillar 966M Wheel Loader. It describes 43 steps for assembling the torque converter, including installing bearings, seals, springs, and other parts. It also describes 3 steps for separating the transmission from the output transfer gears, including removing bolts and disconnecting harness assemblies. Tools including lifting eyes and forcing screws are required. Safety notices are provided regarding keeping parts clean and preventing injury when handling spring-loaded components.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including links, brackets, and a transmission repair stand are required.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including links, brackets, and a transmission repair stand are required.
The document provides step-by-step instructions for assembling a torque converter for a 982M wheel loader. It lists 51 steps to install various components like seals, bearings, gears, plates and bolts. Tools required include link brackets, dial indicators, drivers and guide studs. Temperatures must be controlled for some components during installation. The assembly is completed by connecting the torque converter to the transmission and output transfer gears.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
The document provides step-by-step instructions for assembling a torque converter for a 982M wheel loader. It lists 51 steps to install various components like seals, bearings, gears, plates, and bolts. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Precautions are given for heating/cooling components and proper torque values.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
The document provides step-by-step instructions for assembling a torque converter for a 982M wheel loader. It lists 51 steps to install various components like seals, bearings, gears, plates, and bolts. Tools required include link brackets, dial indicators, drivers, and retaining ring pliers. Temperatures must be carefully controlled for some components. The assembly is completed by connecting the fully assembled torque converter to the transmission and output transfer gears.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including links, brackets, and a transmission repair stand are required.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It describes 38 steps to assemble various internal components like bearings, seals, gears, and housings. Tools required include link brackets, eyebolts, pliers, and Loctite. Torque specifications are provided for many bolts. The summary concludes by stating to connect the assembled torque converter to the transmission and output gears, referring to other service documents.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps to assemble various components like bearings, seals, gears, and housings. Tools required include link brackets, eyebolts, pliers, and Loctite. Torque specifications are provided for many bolts. The summary concludes by stating to connect the assembled torque converter to the transmission and output gears, as outlined in other service manuals.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
This document provides instructions for assembling and disassembling the torque converter and transmission of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners in the correct order and with proper torque specifications. It also outlines 11 steps for disassembling the transmission planetary, such as removing housing components, seals, gears, and the carrier assembly. The overall document provides detailed technical specifications and diagrams to guide maintenance and repair of these powertrain components.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It describes 38 steps to assemble various internal components like bearings, seals, gears, and housings. Special tools are required for some steps. Finally, it states to connect the assembled torque converter to the transmission and output gears by referring to other service manuals.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...kfjksekfmem
This document provides instructions for assembling and disassembling parts of the torque converter and transmission for a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and housing components in the proper order and orientation. It also describes separating the transmission planetary group from the output transfer gear case and disassembling the transmission planetary.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...fjjskekdmem
This document provides instructions for assembling and disassembling the torque converter and transmission on a Caterpillar 962G wheel loader. It describes 38 steps to assemble the torque converter, including installing bearings, seals, gears, and housing components in the proper order and orientation. It also describes 11 steps to disassemble the transmission planetary, such as removing seals, bolts, clutches, and gears. Tools required are listed for each procedure.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...fujsjejfkskemm
This document provides instructions for assembling and disassembling the torque converter and transmission on a Caterpillar 962G wheel loader. It describes 38 steps to assemble the torque converter, including installing bearings, seals, gears, and housing components in the proper order and torque specifications. It also describes separating the transmission from the torque converter and output gears, as well as 11 steps for disassembling the transmission planetary, including removing clutch plates, seals, and housing components. The overall document provides detailed technical instructions for servicing the powertrain on the 962G wheel loader.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...udjjjsjekkdm
This document provides instructions for assembling and disassembling the torque converter and transmission on a Caterpillar 962G wheel loader. It describes 38 steps to assemble the torque converter, including installing bearings, seals, gears, and housing components in the proper order and torque specifications. It also describes separating the transmission from the torque converter and output gears, as well as 11 steps for disassembling the transmission planetary, including removing clutch plates, seals, and housing components. The document contains diagrams illustrating each step for servicing these powertrain components.
This document provides disassembly and assembly instructions for the transmission of a D6R track-type tractor. It details removing and installing over 80 individual parts. Key steps include separating the transmission from the bevel gear, removing the planetary group and transmission cover, and disassembling the individual clutch housings, gears, shafts, and carriers. Proper inspection and cleaning of parts is noted.
This document provides instructions for disassembling and assembling the final drive of a D6R track-type tractor. The disassembly procedure involves using various tools to remove 19 different components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and includes precautions for installing seals and bearings correctly.
The document provides instructions for removing and installing final drives on a D6R track-type tractor. It describes:
1) Removing the final drives which involves draining oil, removing mounting bolts and hardware, and lifting the drive out.
2) Disassembling the final drives by removing planetary carriers, gears, shafts, seals, and other components.
3) Assembling the final drives by reversing the disassembly steps and ensuring proper installation of seals, gears, carriers, and mounting hardware.
4) Reinstalling the final drives by lifting them into place, inserting mounting bolts and hardware, and refilling with oil.
This document provides instructions for removing and disassembling a final drive from a D6R track-type tractor, as well as assembling a final drive. Key steps include using specialized tools to remove the final drive and axle, disassembling internal components like planetary gears and carriers, and precisely installing seals and bearings during assembly. Safety notices warn of risks like uncontrolled machine movement if brakes are ineffective during removal.
This document provides instructions for disassembling and assembling the torque divider of a D6R track-type tractor. It describes removing and installing over 30 different components of the torque divider. Key steps include using tools and hoists to remove large components like the torque divider housing weighing 145 kg, and precisely measuring clearances between components like the stator and turbine wheel to be between 1.76 to 1.94 mm. Reassembly involves installing bearings and seals, heating components, and torquing bolts to specified values.
More Related Content
Similar to Caterpillar Cat 972M Wheel Loader (Prefix JPR) Service Repair Manual (JPR00001 and up).pdf
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including links, brackets, and a transmission repair stand are required.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It describes 38 steps to assemble various internal components like bearings, seals, gears, and housings. Tools required include link brackets, eyebolts, pliers, and Loctite. Torque specifications are provided for many bolts. The summary concludes by stating to connect the assembled torque converter to the transmission and output gears, referring to other service documents.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps to assemble various components like bearings, seals, gears, and housings. Tools required include link brackets, eyebolts, pliers, and Loctite. Torque specifications are provided for many bolts. The summary concludes by stating to connect the assembled torque converter to the transmission and output gears, as outlined in other service manuals.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
This document provides instructions for assembling and disassembling the torque converter and transmission of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners in the correct order and with proper torque specifications. It also outlines 11 steps for disassembling the transmission planetary, such as removing housing components, seals, gears, and the carrier assembly. The overall document provides detailed technical specifications and diagrams to guide maintenance and repair of these powertrain components.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It describes 38 steps to assemble various internal components like bearings, seals, gears, and housings. Special tools are required for some steps. Finally, it states to connect the assembled torque converter to the transmission and output gears by referring to other service manuals.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
This document provides instructions for assembling and disassembling the torque converter and transmission planetary components of a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and fasteners. It also describes 4 steps for separating the transmission planetary from the output transfer gear case, and lists tools and 29 steps for disassembling the transmission planetary.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...kfjksekfmem
This document provides instructions for assembling and disassembling parts of the torque converter and transmission for a Caterpillar 962G wheel loader. It describes 38 steps for assembling the torque converter, including installing bearings, seals, gears, and housing components in the proper order and orientation. It also describes separating the transmission planetary group from the output transfer gear case and disassembling the transmission planetary.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...fjjskekdmem
This document provides instructions for assembling and disassembling the torque converter and transmission on a Caterpillar 962G wheel loader. It describes 38 steps to assemble the torque converter, including installing bearings, seals, gears, and housing components in the proper order and orientation. It also describes 11 steps to disassemble the transmission planetary, such as removing seals, bolts, clutches, and gears. Tools required are listed for each procedure.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...fujsjejfkskemm
This document provides instructions for assembling and disassembling the torque converter and transmission on a Caterpillar 962G wheel loader. It describes 38 steps to assemble the torque converter, including installing bearings, seals, gears, and housing components in the proper order and torque specifications. It also describes separating the transmission from the torque converter and output gears, as well as 11 steps for disassembling the transmission planetary, including removing clutch plates, seals, and housing components. The overall document provides detailed technical instructions for servicing the powertrain on the 962G wheel loader.
Caterpillar cat 962 g wheel loader (prefix 7bw) service repair manual (7bw000...udjjjsjekkdm
This document provides instructions for assembling and disassembling the torque converter and transmission on a Caterpillar 962G wheel loader. It describes 38 steps to assemble the torque converter, including installing bearings, seals, gears, and housing components in the proper order and torque specifications. It also describes separating the transmission from the torque converter and output gears, as well as 11 steps for disassembling the transmission planetary, including removing clutch plates, seals, and housing components. The document contains diagrams illustrating each step for servicing these powertrain components.
Similar to Caterpillar Cat 972M Wheel Loader (Prefix JPR) Service Repair Manual (JPR00001 and up).pdf (17)
This document provides disassembly and assembly instructions for the transmission of a D6R track-type tractor. It details removing and installing over 80 individual parts. Key steps include separating the transmission from the bevel gear, removing the planetary group and transmission cover, and disassembling the individual clutch housings, gears, shafts, and carriers. Proper inspection and cleaning of parts is noted.
This document provides instructions for disassembling and assembling the final drive of a D6R track-type tractor. The disassembly procedure involves using various tools to remove 19 different components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and includes precautions for installing seals and bearings correctly.
The document provides instructions for removing and installing final drives on a D6R track-type tractor. It describes:
1) Removing the final drives which involves draining oil, removing mounting bolts and hardware, and lifting the drive out.
2) Disassembling the final drives by removing planetary carriers, gears, shafts, seals, and other components.
3) Assembling the final drives by reversing the disassembly steps and ensuring proper installation of seals, gears, carriers, and mounting hardware.
4) Reinstalling the final drives by lifting them into place, inserting mounting bolts and hardware, and refilling with oil.
This document provides instructions for removing and disassembling a final drive from a D6R track-type tractor, as well as assembling a final drive. Key steps include using specialized tools to remove the final drive and axle, disassembling internal components like planetary gears and carriers, and precisely installing seals and bearings during assembly. Safety notices warn of risks like uncontrolled machine movement if brakes are ineffective during removal.
This document provides instructions for disassembling and assembling the torque divider of a D6R track-type tractor. It describes removing and installing over 30 different components of the torque divider. Key steps include using tools and hoists to remove large components like the torque divider housing weighing 145 kg, and precisely measuring clearances between components like the stator and turbine wheel to be between 1.76 to 1.94 mm. Reassembly involves installing bearings and seals, heating components, and torquing bolts to specified values.
This document provides instructions for disassembling and assembling the bevel and transfer gears of a D6R track-type tractor. It describes removing over 30 individual components in 26 steps, including the transmission gears, bearings, seals, and housings. Reassembly is outlined in 38 steps, with specifics on heating and installing bearings, applying sealant, adjusting end play and backlash using shims and gauges, and torquing bolts. The document is highly technical and aimed at mechanics performing gearbox maintenance and repairs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model 558. It details 25 steps for disassembly, removing components like gears, shafts, seals and housings. It notes cleaning and inspecting parts before assembly. The assembly section lists 13 steps to reinstall components in reverse order, applying compounds and ensuring cleanliness. Special tools are listed to aid in removal and installation of heavy components weighing up to 510kg. Safety precautions are provided to contain fluids and protect personnel.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...hdjsjndndnd
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and drivers. Safety notices are provided regarding contained fluids, spring force, and being struck by parts.
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include:
1) Draining oil from the final drive and removing covers, axles, and bolts holding components in place.
2) Using lifting tools and hoists to remove heavy components like final drives weighing over 600 kg.
3) Inspecting seals and bearings during disassembly and applying clean oil during assembly.
4) Heating and pressing bearings and seals into place during reassembly and torquing bolts to specified values.
Caterpillar Cat 390D L Excavator (Prefix WBT) Service Repair Manual (WBT00001...hdjsjndndnd
This document provides disassembly and assembly instructions for the travel motor on a 390D L excavator. It describes 40 steps to disassemble the travel motor, removing components like the head, relief valves, pistons, springs, seals and bearings. It then describes 3 steps to begin reassembling the travel motor, starting with installing the lip seal, bearing and retaining ring. Detailed illustrations are provided for each step. Cleanliness and applying lubricant to parts are emphasized during disassembly and assembly.
Caterpillar Cat 385C L Excavator (Prefix KKK) Service Repair Manual (KKK00001...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It begins with a list of required tools. The disassembly procedure has 33 steps that remove components like the housing cover, carrier assemblies, planetary gears, ring gear, and seals. The assembly procedure has 17 steps that install components in reverse order, noting the importance of cleanliness and applying lubricants where specified.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix JDL) Service Repair Manual...hdjsjndndnd
The document provides instructions for disassembling and assembling the final drive of a D6R III track-type tractor. The disassembly procedure involves 19 steps to remove components such as the planetary carrier, gears, seals, and hub. The assembly procedure describes 15 steps including pressing components, installing seals and bearings at specified temperatures, and torquing bolts to the correct specifications. Proper cleaning, lubrication, and use of specialized tools are emphasized to correctly perform the processes.
The document provides instructions for disassembling and assembling the travel motor of a 385C Excavator. It lists 40 steps for disassembly, including removing the head, relief valves, spools, pistons, springs, port plate, and other internal components. It then lists 16 steps for reassembly, starting with installing internal seals and moving outward to reinstalling the piston, port plate, spools, and head. Precautions are provided regarding cleaning parts, applying oil, and ensuring proper alignment of components.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix HCD) Service Repair Manual...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive components of a Caterpillar D6R III track-type tractor. The disassembly process involves using various tools to remove 19 components including planetary gears, bearings, seals, and hubs. The assembly process similarly uses tools to reinstall the components in the reverse order, taking care to clean parts and apply oil, and heat or cool components as needed to ensure proper installation. Special installation procedures are specified for seals and bearings.
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It begins with a list of required tools. The disassembly procedure has 33 steps that remove components like the housing cover, carrier assemblies, planetary gears, ring gear, and seals. The assembly procedure has 17 steps that install components in reverse order, noting the importance of cleanliness and applying lubricants where specified.
This document provides instructions for disassembling the control valve for the attachment, bucket, boom, right travel, left travel, and stick systems of a 385B Excavator. It outlines 25 steps to disassemble the various components of the control valve, including removing covers, seals, valves, pistons, solenoids, manifolds, and other parts. Precautions are provided to watch out for spring forces and to keep components clean during disassembly. Tools required include pliers. The goal is to disassemble the control valve into its individual parts to allow for inspection and replacement of any worn components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix FDT) Service Repair Manual ...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. The disassembly process involves using various tools to remove 19 different parts from the final drive assembly, including the planetary carrier, gears, seals, and hub. The assembly process describes 16 steps for reinstalling the parts in reverse order and includes safety notices and requirements for cleaning, lubricating, and heating components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BRJ) Service Repair Manual ...hdjsjndndnd
The document provides instructions for disassembling the transmission of a D6R II track-type tractor. It lists the required tools and gives step-by-step instructions to remove components such as tubes, valves, gears, housings, pistons, seals, and plates. Special care must be taken to keep parts like discs and plates organized according to their clutch assemblies. Dismantling involves using lifting devices and compression tools to handle heavy internal components.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BLE) Service Repair Manual ...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. The disassembly procedure involves using various tools to remove 19 parts from the final drive assembly, including the planetary carrier, gears, seals, and hub. The assembly procedure describes 16 steps for installing the parts in reverse order, noting the importance of cleanliness and applying oil during assembly. Torque specifications and heating instructions are provided for certain bolts and bearings.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BMK) Service Repair Manual ...hdjsjndndnd
The document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. It describes in detail how to remove and install components such as the planetary carrier, hub, ring gear, and seals using the proper tools. Cleanliness is emphasized throughout the process to prevent dirt from entering parts. Proper bearing installation and torque specifications are also outlined to ensure correct assembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972M WHEEL LOADER JPR
Configuration: 972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
966M and 972M Wheel Loaders Power Train
Media Number -UENR0378-12 Publication Date -01/09/2015 Date Updated -05/10/2017
i05277906
Torque Converter (Freewheel Stator) (Lockup) - Assemble
SMCS - 3101-016-L7
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5472 Lifting Eye Assembly 3
B 1P-0520 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g03355787
1. Use a suitable press in order to install bearing race (61) onto shaft (58).
Illustration 2 g03355638
2. Install seals (59) onto shaft (58). Install seal (60).
Illustration 3 g03355625
3. Install bearing (57) and retaining ring (56).
2/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 4 g03355621
4. Install seal (55) onto stator carrier assembly (51).
Illustration 5 g03355790
5. Use Tooling (B) and a suitable press in order to install bearing (54) (not shown) into gear
(53).
Illustration 6 g03355793
6. Use Tooling (B) and a suitable press in order to install stator carrier assembly (51) into gear
(53).
3/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 10 g03355520
10. Install impeller hub (48) and impeller (49). Install bolts (47). Tighten bolts (47) to a torque
of 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 11 g03355514
11. Install thrust bearing (46).
Illustration 12 g03357305
12. Use Tooling (B) and a suitable press in order to install cam (45) (not shown) into stator (37).
5/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 13 g03357299
Illustration 14 g03357350
13. Install race (42), freewheel springs (43), and freewheel rollers (44).
Note: Be sure to install freewheel springs with the lesser number of loops going toward race
(42), as shown in Illustration 14.
Illustration 15 g03357298
6/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install plate (41) and retaining ring (40) into stator (37).
Illustration 16 g03357296
15. Flip the stator over and install plate (39) and retaining ring (38).
Illustration 17 g03355513
16. Install stator (37).
7/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 18 g03355511
17. Install thrust bearing (36).
Illustration 19 g03355507
18. Connect turbine (34) to turbine hub (35). Install two bolts (20) in order to keep turbine (34)
and turbine hub (35) together during the Step 19.
Illustration 20 g03355497
19. Install turbine (34) to turbine hub (35) as one unit. Remove bolts (20).
8/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 27 g03355386
26. Install springs (26) and (25) inside of springs (24). Install springs (24) in an alternating
pattern. An example would be to install a spring (24) and with a spring (25) inside. The next
one would be to install a spring (24) with a spring (26) inside.
Illustration 28 g03355362
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install plate (23) to coupling assembly (21). Install bolts (22). Tighten bolts (22) to a torque
of 50 ± 10 N·m (37 ± 7 lb ft).
11/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 29 g03355353
28. Install coupling assembly (21). Install bolts (20). Tighten bolts (20) to a torque of
60 ± 7 N·m (44 ± 5 lb ft).
Illustration 30 g03355350
29. Install seal ring (19) into piston (18).
Illustration 31 g03355310
30. Install piston (18).
12/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 32 g03355307
31. Install O-ring seal (17). Install bushing (16) into housing assembly (15).
Illustration 33 g03355853
32. Install housing assembly (15) into the torque converter.
Illustration 34 g03355265
33. Install bolts (13). Tighten bolts (13) to a torque of 60 ± 7 N·m (44 ± 5 lb ft). Install seal
(14).
13/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 35 g03355259
34. Position torque converter (12) as shown.
Illustration 36 g03356180
35. Use Tooling (B) in order to install bearing (11) in pump drive gear (9).
Illustration 37 g03355946
36. Attach Tooling (A) and a suitable lifting device to torque converter housing (10). The
weight of torque converter housing (10) is approximately 100 kg (220 lb). Use Tooling (A)
and the suitable lifting device in order to install torque converter housing (10) over the
torque converter.
14/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 38 g02139389
37. Install pump drive gear (9) and drive gear shaft (8).
38. Install bolt (7) and the washer that holds drive gear shaft (8) to the torque converter housing.
Tighten bolt (7) to a torque of 240 ± 40 N·m (180 ± 30 lb ft).
Illustration 39 g03356370
39. Install pump drive flange (6) and bolts (62). Tighten bolts (62) to a torque of 60 ± 12 N·m
(44 ± 9 lb ft).
Illustration 40 g02139369
15/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. 40. Install bolts (4) and the washers that hold the torque converter to the torque converter
housing. Tighten bolts (4) to a torque 50 ± 10 N·m (37 ± 7 lb ft).
41. Install O-ring seal (5).
Illustration 41 g03569473
42. Install gear (3). Tighten bolt (63) to a torque of 120 ± 20 N·m (90 ± 15 lb ft).
43. Install torque converter speed sensor (2), the seal, and the washer. Tighten torque converter
speed sensor (2) to a torque of 25 ± 5 N·m (18 ± 4 lb ft).
End By:
a. Connect the torque converter to the transmission and the output transfer gears.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 6 17:06:57 UTC+0800 2021
16/16
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972M WHEEL LOADER JPR
Configuration: 972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
966M and 972M Wheel Loaders Power Train
Media Number -UENR0378-12 Publication Date -01/09/2015 Date Updated -05/10/2017
i06909789
Transmission from Output Transfer Gears - Separate
SMCS - 3002-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
B 154-6181 Forcing Screw 3
Start By:
a. Separate the torque converter from the transmission.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g03367331
1. Remove bolts (1) and tube assembly (2).
Illustration 2 g03367336
2. Disconnect harness assemblies (3).
Illustration 3 g03367344
3. Attach Tooling (A) and a suitable lifting device to transmission (4). The weight of
transmission (4) is approximately 425 kg (936 lb).
2/4
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 4 g02161929
Illustration 5 g02162314
4. Remove bolts (5) and (6) that connect transmission (4) with output transfer gears (7).
Illustration 6 g02162331
5. Use Tooling (B) to separate transmission (4) from output transfer gears (7).
6. Remove transmission (4).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Tue Apr 6 17:07:54 UTC+0800 2021
3/4
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972M WHEEL LOADER JPR
Configuration: 972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
966M and 972M Wheel Loaders Power Train
Media Number -UENR0378-12 Publication Date -01/09/2015 Date Updated -05/10/2017
i06909951
Transmission Planetary - Disassemble
SMCS - 3160-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3940 Bracket As 3
C 1P-0520 Driver Gp 1
D 8B-7551 Bearing Puller 1
Start By:
a. Separate the transmission from the output transfer gears.
Note: Cleanliness is an important factor. Before the disassembly procedure, clean the exterior of
the component . Cleaning will help to prevent dirt from entering the internal mechanism.
1/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 1 g03371891
1. Remove O-ring seal (1) from the housing.
2. Remove bolt (2). Remove drive gear (3) from the end of the input shaft.
Illustration 2 g02146314
3. Remove plate (4).
Illustration 3 g03368860
4. Attach Tooling (B) and a suitable lifting device to the transmission, as shown. The weight
of the transmission is approximately 425 kg (936 lb).
2/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. 5. Carefully position the transmission on the opposite end so that No. 6 clutch housing (5) is
facing upward, as shown.
Illustration 4 g03371894
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
6. Remove retaining ring (6) from output shaft assembly (7). Remove bolts (8) and No. 6
clutch housing (5). Mark the location of the long bolts.
Illustration 5 g02146318
7. Remove clutch piston (9) from No. 6 clutch housing (5).
8. Remove seal rings (10) and (11) from clutch piston (9).
3/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 6 g02146333
9. Remove clutch plate (12), springs (13), and the pins.
Illustration 7 g02146353
10. Remove clutch plates (12) and friction discs (14). Remove dowels (15).
Illustration 8 g02146354
11. Remove ring gear (16).
4/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 9 g02146356
12. Remove carrier assembly (17). Remove bolts (18).
Illustration 10 g02146358
13. Remove metal seal ring (19) from carrier assembly (17).
Illustration 11 g03369514
14. Push the spring pins (20) through carrier assembly (17) and into planetary shafts (21).
Remove planetary shafts (21) from carrier assembly (17).
5/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 12 g02146362
15. Remove thrust discs (22), planetary gears (23), and bearings (24) from the carrier assembly.
Remove spring pins (20) from planetary shafts (21).
Illustration 13 g03369518
16. Disconnect the harness assemblies (26) which are attached to transmission modulating
valves (25). Remove transmission modulating valves (25) from the transmission housing.
Illustration 14 g02146368
17. Remove retaining ring (27) and (28).
6/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 15 g03368870
18. Use Tooling (B) and a suitable lifting device to remove housing assembly (29). The weight
of housing assembly (29) is approximately 88 kg (195 lb).
Illustration 16 g02146402
19. Remove bearing (30) from housing assembly (29).
Illustration 17 g03369527
20. Remove retaining ring (33) and clutch assembly (31). Remove springs (32) and rods (34)
(not shown).
7/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 18 g03369533
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
21. Use steel spacers and a suitable press to install retainer plate (35). Remove retaining ring
(36) from the clutch assembly (31).
Illustration 19 g03369538
8/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 20 g03369542
22. Separate retaining ring (36), retainer plate (35), and five coned disc springs (37). Remove
seal rings (39) from clutch piston (38). Remove seal rings (41) from clutch housing (40).
Illustration 21 g03368881
23. Remove friction discs (42) and clutch plates (43). Remove dowels (44).
Illustration 22 g03368887
24. Remove retaining ring (45) from output shaft assembly (7). Remove sun gear (46).
9/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SEBP...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Illustration 23 g03368894
25. Remove friction discs (47) and clutch plates (48).
Illustration 24 g03368903
26. Remove ring gear (49).
Illustration 25 g03368911
27. Remove retaining ring (50). Remove plate (51) from ring gear (49).
10/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. Illustration 26 g03368917
28. Remove clutch piston (53). Remove O-ring seal (52). Use Tooling (B) and a suitable lifting
device to remove housing (54). The weight of housing (54) is approximately 54 kg (119 lb).
Note: Remove the clutch piston in the bottom of housing (54). The clutch piston may be
stuck in housing (54). As housing (54) is removed, the other clutch piston may fall.
Illustration 27 g03368958
29. Remove seal rings (55) and (56) from clutch pistons (53).
Illustration 28 g03368965
11/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
32. 30. Remove dowels (57). Remove O-ring seal (58). Remove clutch plate (59). Remove springs
(60).
31. Remove friction discs (61) and clutch plates (59).
Illustration 29 g03368978
32. Remove carrier assembly (62).
Illustration 30 g03368982
33. Use several small steel rods (64) ( 3.175 mm (0.1250 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (62) to ring gear (65).
34. Remove carrier assembly (62) from ring gear (65). Remove ring seal (63).
12/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
33. Illustration 31 g03368984
35. Remove retaining ring (66) from carrier assembly (62).
Illustration 32 g03368986
36. Use a suitable punch to push spring pins (67) (not shown) through carrier assembly (62) and
into planetary shafts (68).
Illustration 33 g03368993
37. Remove thrust discs (69), planetary gears (70), and bearings (71) from the carrier assembly.
Remove spring pins (67) from planetary shafts (68).
13/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
34. Illustration 34 g03368998
38. Remove retaining ring (72). Remove output shaft assembly (7).
Illustration 35 g03368999
39. Remove retaining ring (75). Remove sun gear (74). Remove bearing (73). Remove bearings
(76) from each end of output shaft assembly (7).
Illustration 36 g03369002
Illustration 37 g03369004
14/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
35. 40. Remove bolts (78). Use Tooling (B) and a suitable lifting device to remove housing (77).
The weight of housing (77) is approximately 61 kg (135 lb).
Note: Remove clutch piston (79) in the bottom of housing (77). Clutch piston (79) may be
stuck in housing (77). As housing (77) is removed, clutch piston (79) may fall.
41. Remove seal rings (80) from clutch piston (79).
Illustration 38 g03369196
42. Remove plate (81). Remove springs (82). Remove dowels (83). Remove friction discs (84)
and clutch plates (85).
Illustration 39 g03369203
43. Remove retaining ring (87). Use two people to remove carrier assembly (86). The weight of
carrier assembly (86) is approximately 29 kg (65 lb)
15/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
36. Illustration 40 g03369312
44. Remove ring gear (88) from carrier assembly (86).
Illustration 41 g03369218
45. Use several small steel rods (89) ( 2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (86) to ring gear (90) together.
46. Remove ring gear (90) from carrier assembly (86).
Illustration 42 g03369321
16/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
37. 47. Use a suitable punch to push spring pins (91) through carrier assembly (86) and into
planetary shafts (92).
Illustration 43 g03369333
48. Use a suitable punch to remove planetary shafts (92) from carrier assembly (86).
Illustration 44 g03369340
49. Open retaining ring (93) into slots in the planetary shaft holes. Use Tooling (C) to remove
bearing (94) and sun gear (95) from carrier assembly (86). Remove thrust disc (96).
Illustration 45 g03369356
17/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
38. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
39. 50. Remove thrust discs (97), planetary gears (98), and bearings (99) from the carrier assembly.
51. Remove spring pins (91) from planetary shafts (92).
Illustration 46 g03369388
52. Remove O-ring seal (100). Remove plate (101).
Illustration 47 g03369404
53. Remove O-ring seal (102). Remove friction discs (103) and clutch plates (104).
Illustration 48 g03369414
18/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
40. 54. Remove ring carrier (105) and carrier assembly (106).
Illustration 49 g03369415
55. Use a suitable punch to push spring pins (107) through carrier assembly (106) and into
planetary shafts (108).
Illustration 50 g03369423
56. Remove thrust discs (109), planetary gears (110), and bearings (111) from the carrier
assembly. Remove spring pins (107) from planetary shafts (108).
Illustration 51 g03369430
19/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
41. 57. Remove coupling (112). Remove sun gear (113).
Illustration 52 g03369437
58. Remove clutch piston (114).
Illustration 53 g03369478
59. Remove seal rings (115) and (116) from clutch piston (114).
Illustration 54 g03369487
60. Remove retaining ring (117) to remove input shaft (119) from housing (118).
20/21
972M Wheel Loader JPR00001-UP (MACHINE) POWERED BY C9.3 Engine(SE...
2021/4/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...