Caterpillar Cat 962H Wheel Loader (Prefix M3G) Service Repair Manual (M3G00001 and up).pdf

Service Repair Manual
Models
962H WHEEL LOADER

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962H WHEEL LOADER M3G
Configuration: 962H Wheel Loader M3G00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Machine Systems
Media Number -RENR8881-01 Publication Date -01/06/2009 Date Updated -08/06/2009
i02288172
Piston Pump (Steering) - Disassemble
SMCS - 4306-015; 5070-015-ZH
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-4878 Plate(1)
1
B 1P-1861 Retaining Ring Pliers 1
(1)
33.3 mm (1.31 inch) diameter
Start By:
a. Remove the steering pump. Refer to Disassembly and Assembly, "Piston Pump (Steering) -
Remove".
Illustration 1 g01145338
1/10
962H Wheel Loader M3G00001-UP (MACHINE) POWERED BY C7 Engine(SEBP4...
2020/3/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

1. Remove bolts (1) and valve (2).
2. Remove O-ring seals (3) from valve (2).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (4), the O-ring seals, plug (5), and plug (6).
2/10
2020/3/27

4. Remove spool (7) and spool (8).
5. Remove the O-ring seals from plug (5) and plug (6).
6. Remove adjustment screw (9) and adjustment screw (10).
3/10
2020/3/27

7. Remove retainer (14), spacer (13), spring (12), and retainer (11).
8. Remove retainer (17), spring (16), and retainer (15).
9. Remove the O-ring seals from adjustment screw (9) and adjustment screw (10).
10. Remove bolts (18) and elbow (19).
4/10
2020/3/27

11. Remove bolts (20) and head (21).
12. Remove plate (22).
13. Remove bearing cup (23) and pin (24).
Note: Place the steering pump on suitable blocks, as shown.
5/10
2020/3/27

14. Remove bearing cone (26) and gasket (9).
15. Remove spacer (28) and barrel assembly (29).
16. Remove spring (27) and piston (30).
6/10
2020/3/27

17. Use Tooling (A) and a suitable press to disassemble barrel assembly (29).
a. Compress spring (31) until Tooling (A) is below retaining ring (33).
b. Remove retaining ring (33) and slowly release the spring tension.
c. Remove spring (31) and washers (32).
18. Remove bolts (34) and cover (35).
7/10
2020/3/27

19. Remove plug (36).
20. Remove O-ring seal (38) from the cover. Remove O-ring seal (39) from the plug.
21. Remove shaft (37).
22. Remove bolts (40) and two spacer plates (41).
23. Remove pistons (42) and the plate.
8/10
2020/3/27

24. Remove spacer plates (43) and swashplate (44).
25. Remove bearing cone (45).
26. Use Tooling (B) in order to remove retaining ring (46) and seal (47).
9/10
2020/3/27

27. Remove bearing cup (48).
28. Remove screws (50). Remove bearings (49) and (51).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 27 16:58:32 UTC+0800 2020
10/10
962H Wheel Loader M3G00001-UP (MACHINE) POWERED BY C7 Engine(SEB...
2020/3/27

Shutdown SIS
Previous Screen
i02288174
Piston Pump (Steering) - Assemble
SMCS - 4306-016; 5070-016-ZH
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-4878 Plate(1)
1
B 1P-1861 Retaining Ring Pliers 1
(1)
33.3 mm (1.31 inch) diameter
1. Lower the temperature of bearing cup (48).
2. Install bearing cup (48).
1/10
2020/3/27

3. Install bearings (49) and (51).
4. Install screws (50).
5. Install seal (47).
6. Use Tooling (B) in order to install retaining ring (46).
7. Install bearing cone (45).
2/10
2020/3/27

8. Install swashplate (44) and spacer plates (43).
9. Install pistons (42) and the plate.
10. Install bolts (40) and spacer plates (41).
11. Install O-ring seal (38) onto the cover. Install O-ring seal (39) onto the plug.
12. Install shaft (37).
3/10
2020/3/27

13. Install cover (35) and bolts (34).
14. Install plug (36).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
15. Use Tooling (A) and a suitable press to assemble barrel assembly (29).
a. Install spring (31) and washers (32).
4/10
2020/3/27

b. Compress spring (31) until Tooling (A) is below retaining ring (33).
c. Install retaining ring (33) and slowly release the spring tension.
16. Install barrel assembly (29) and spacer (28).
17. Install spring (27) and piston (30).
18. Install bearing cone (26) and gasket (9).
5/10
2020/3/27

19. Install bearing cup (23) and pin (24).
20. Install plate (22).
injury.
21. Install head (21) and bolts (20).
22. Tighten bolts (20) to a torque of 91 ± 4 N·m (67 ± 3 lb ft).
6/10
2020/3/27

23. Install elbow (19) and bolts (18).
24. Install the O-ring seals onto adjustment screw (9) and adjustment screw (10).
25. Install retainer (15), spring (16), and retainer (17).
26. Remove retainer (11), spring (12), spacer (13), and retainer (14).
7/10
2020/3/27

injury.
27. Install adjustment screw (9) and adjustment screw (10).
28. Install spool (7) and spool (8).
29. Install the O-ring seals onto plug (5) and plug (6).
30. Install the O-ring seal, plug (4), plug (5), and plug (6).
8/10
2020/3/27

31. Install O-ring seals (3) onto valve (2).
32. Install valve (2) and bolts (1).
33. Tighten bolts (1) to a torque of 34 ± 3 N·m (25 ± 2 lb ft).
34. Use a dial indicator to check the axial shaft end play. Put the dial indicator on the end of the
shaft and pull on the shaft.
9/10
2020/3/27

The correct axial shaft end play is 0.01 to 0.10 mm (0.0004 to 0.004 inch). Use the correct
shim to achieve this dimension.
End By:
a. Install the steering pump. Refer to Disassembly and Assembly, "Piston Pump (Steering) -
Install".
Fri Mar 27 16:59:28 UTC+0800 2020
10/10
962H Wheel Loader M3G00001-UP (MACHINE) POWERED BY C7 Engine(SEB...
2020/3/27

Shutdown SIS
Previous Screen
i02520131
Piston Pump (Steering) - Install
SMCS - 4306-012; 5070-012-ZH
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1. Install O-ring seal (8) and coupling (7) .
1/4
2020/3/27

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

2. Use a suitable lifting device to position steering piston pump (6) . The weight of steering
piston pump (6) is approximately 50 kg (110 lb).
3. Install bolts (5) .
4. Connect hose assembly (4) .
2/4
2020/3/27

5. Connect hose assemblies (3) .
6. Install bracket assembly (2) .
7. Connect tube assembly (1) .
3/4
2020/3/27

NOTICE
To avoid system damage, make sure that the hydraulic pump is
properly filled with hydraulic oil before start-up.
8. In order to fill the case of the implement pump, the steering pump, and the fan pumps, fully
open fill valve (9) that is located between the hydraulic tank and the implement pump.
9. Attach a bleed line to pressure tap (10) that is located in the case drain line above the fan
pump.
10. Begin filling the hydraulic tank with oil. Once oil begins to flow out of the bleed line,
remove the bleed line and fully close the fill valve.
11. Continue to fill the hydraulic tank to the correct level. Refer to Operation and Maintenance
Manual, "Hydraulic System Oil - Change".
Note: During initial start-up, the engine should never run higher than low idle until the
hydraulic system has been cycled and the hydraulic tank oil level has been readjusted to the
correct level.
End By: Install the cab. Refer to Disassembly and Assembly, "Cab - Install".
Fri Mar 27 17:00:24 UTC+0800 2020
4/4
2020/3/27

Caterpillar Cat 962H Wheel Loader (Prefix M3G) Service Repair Manual (M3G00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 962H Wheel Loader (Prefix M3G) Service Repair Manual (M3G00001 and up).pdf

Similar to Caterpillar Cat 962H Wheel Loader (Prefix M3G) Service Repair Manual (M3G00001 and up).pdf (20)

More from fyhsejdkkdmmd3e

More from fyhsejdkkdmmd3e (20)

Recently uploaded

Recently uploaded (10)

Caterpillar Cat 962H Wheel Loader (Prefix M3G) Service Repair Manual (M3G00001 and up).pdf