1) The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2) It describes removing over 40 individual components in 38 steps, and installing them in reverse order over 29 steps.
3) Key components that must be removed include the transmission oil pump, torque converter speed sensor, various bolts and gears, and the turbine assembly, and reinstalled in the proper orientation.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for each fastener. Tools required include link brackets, eyebolts and retaining ring pliers.
This document provides assembly instructions for a torque converter in a 962G wheel loader. It outlines 40 steps to disassemble the torque converter into its individual components and 29 steps to reassemble it. Key components that are removed and installed include the torque converter housing, various gears, bearings, seals, and fasteners. Special tools are required for tasks like removing retaining rings.
This document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps for disassembly, removing components like the transmission oil pump, speed sensor, bolts, gears, shafts, bearings, seals, and housing. It then describes 18 steps for reassembly, showing how to install these same components in reverse order, like installing bearings, seals, gears, shafts, housing, and bolts, while applying loctite and torquing bolts to specifications. Tools required are also listed.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for the fasteners. Tools required include link brackets, eyebolts and retaining ring pliers.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...jfjkskefmsmem
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document provides very detailed technical instructions for taking apart and rebuilding the wheel loader's torque converter.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...ufjjjsekkemmd
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document is a service repair manual for maintenance technicians to service the machine's powertrain.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fujsejfjksekkkm
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fjjskekdmnsme
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for each fastener. Tools required include link brackets, eyebolts and retaining ring pliers.
This document provides assembly instructions for a torque converter in a 962G wheel loader. It outlines 40 steps to disassemble the torque converter into its individual components and 29 steps to reassemble it. Key components that are removed and installed include the torque converter housing, various gears, bearings, seals, and fasteners. Special tools are required for tasks like removing retaining rings.
This document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps for disassembly, removing components like the transmission oil pump, speed sensor, bolts, gears, shafts, bearings, seals, and housing. It then describes 18 steps for reassembly, showing how to install these same components in reverse order, like installing bearings, seals, gears, shafts, housing, and bolts, while applying loctite and torquing bolts to specifications. Tools required are also listed.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for the fasteners. Tools required include link brackets, eyebolts and retaining ring pliers.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...jfjkskefmsmem
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document provides very detailed technical instructions for taking apart and rebuilding the wheel loader's torque converter.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...ufjjjsekkemmd
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document is a service repair manual for maintenance technicians to service the machine's powertrain.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fujsejfjksekkkm
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fjjskekdmnsme
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
1. Stop the engine and remove the key before performing any maintenance to prevent accidental starting. Attach a "DO NOT OPERATE" tag to controls.
2. Wear appropriate protective equipment like gloves, glasses and hearing protection when working on or around the machine to avoid injury from parts, debris or loud noises.
3. Release all pressure from hydraulic systems before disconnecting lines or removing caps and plugs to prevent hot fluid from spraying out and causing burns or other injuries.
The document provides safety precautions and cautions for maintenance personnel working on a TL140 crawler loader. It outlines general safety rules, protective equipment requirements, precautions for hot or pressurized components, battery and fuel handling, and cautions for disassembly/assembly. The document emphasizes stopping the engine before work, releasing hydraulic pressure, and securing or blocking components to prevent injury.
This document provides safety precautions and instructions for maintenance personnel working on a crawler loader. It outlines general safety rules including wearing proper protective equipment, blocking the machine securely before working underneath, releasing hydraulic pressure, and disconnecting the battery. The document also provides cautions for disassembly and assembly such as cleaning parts, making matching marks, and replacing seals with new parts.
Takeuchi TB2150 Hydraulic Excavator Service Repair Workshop Manual (Serial No...nkikou1545
1) This manual provides procedures for servicing a machine, including disassembly, assembly, inspection, maintenance, and troubleshooting, as well as service data, specifications, and safety information.
2) Directional terms like front, rear, left, and right are defined based on the perspective of a person sitting in the operator's seat.
3) The machine's serial number is stamped on an identification plate and should be included when ordering parts or making inquiries.
Nissan Forklift Electric P02 Series Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair procedures for the NISSAN FORKLIFT P01 and P02 series. It consists of 14 sections covering general information, maintenance, control systems, batteries/chargers, electrical systems, motor mechanisms, differentials, axles, brakes, steering, hydraulics, loading mechanisms, and bodies/frames. Any updates will be announced in technical bulletins to supplement the appropriate sections. The manual includes service data, trouble diagnoses, precautions, and detailed removal/installation procedures.
Nissan Forklift Electric P01 Series Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair procedures for the NISSAN FORKLIFT P01 and P02 series. It consists of 14 sections covering general information, maintenance, control systems, batteries/chargers, electrical systems, motor mechanisms, differentials, axles, brakes, steering, hydraulics, loading mechanisms, and bodies/frames. The manual outlines how to use it, defines technical terms, and describes how to read wiring diagrams. Safety notices are included to ensure safe service procedures.
New Holland T6.180 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.180 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine and fuel system, transmission, axles, hydraulics, electrical system, climate control, steering, brakes, hitches and 3-point linkage. The manual is intended to be used as a reference for technicians servicing these tractor models. It provides an overview of components, operating principles and troubleshooting information for each system.
New Holland T6.180 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.175 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab components, and more. Specific sections cover maintenance and repairs for components like the fuel system, cooling system, and transmission. The manual also includes fault codes to assist with troubleshooting.
New Holland T6.175 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.175 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
New Holland T6.165 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
New Holland T6.165 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab components, and more. Specific sections cover maintenance and repairs for components like the fuel system, cooling system, and transmission. The manual also includes fault codes to assist with troubleshooting.
New Holland T6.165 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.160 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.155 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.155 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab components, and more. Specific sections cover maintenance and repairs for components like the fuel system, cooling system, and transmission. The manual also includes fault codes to assist with troubleshooting.
New Holland T6.155 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
New Holland T6.145 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
1. Stop the engine and remove the key before performing any maintenance to prevent accidental starting. Attach a "DO NOT OPERATE" tag to controls.
2. Wear appropriate protective equipment like gloves, glasses and hearing protection when working on or around the machine to avoid injury from parts, debris or loud noises.
3. Release all pressure from hydraulic systems before disconnecting lines or removing caps and plugs to prevent hot fluid from spraying out and causing burns or other injuries.
The document provides safety precautions and cautions for maintenance personnel working on a TL140 crawler loader. It outlines general safety rules, protective equipment requirements, precautions for hot or pressurized components, battery and fuel handling, and cautions for disassembly/assembly. The document emphasizes stopping the engine before work, releasing hydraulic pressure, and securing or blocking components to prevent injury.
This document provides safety precautions and instructions for maintenance personnel working on a crawler loader. It outlines general safety rules including wearing proper protective equipment, blocking the machine securely before working underneath, releasing hydraulic pressure, and disconnecting the battery. The document also provides cautions for disassembly and assembly such as cleaning parts, making matching marks, and replacing seals with new parts.
Takeuchi TB2150 Hydraulic Excavator Service Repair Workshop Manual (Serial No...nkikou1545
1) This manual provides procedures for servicing a machine, including disassembly, assembly, inspection, maintenance, and troubleshooting, as well as service data, specifications, and safety information.
2) Directional terms like front, rear, left, and right are defined based on the perspective of a person sitting in the operator's seat.
3) The machine's serial number is stamped on an identification plate and should be included when ordering parts or making inquiries.
Nissan Forklift Electric P02 Series Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair procedures for the NISSAN FORKLIFT P01 and P02 series. It consists of 14 sections covering general information, maintenance, control systems, batteries/chargers, electrical systems, motor mechanisms, differentials, axles, brakes, steering, hydraulics, loading mechanisms, and bodies/frames. Any updates will be announced in technical bulletins to supplement the appropriate sections. The manual includes service data, trouble diagnoses, precautions, and detailed removal/installation procedures.
Nissan Forklift Electric P01 Series Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair procedures for the NISSAN FORKLIFT P01 and P02 series. It consists of 14 sections covering general information, maintenance, control systems, batteries/chargers, electrical systems, motor mechanisms, differentials, axles, brakes, steering, hydraulics, loading mechanisms, and bodies/frames. The manual outlines how to use it, defines technical terms, and describes how to read wiring diagrams. Safety notices are included to ensure safe service procedures.
New Holland T6.180 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.180 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine and fuel system, transmission, axles, hydraulics, electrical system, climate control, steering, brakes, hitches and 3-point linkage. The manual is intended to be used as a reference for technicians servicing these tractor models. It provides an overview of components, operating principles and troubleshooting information for each system.
New Holland T6.180 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.175 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab components, and more. Specific sections cover maintenance and repairs for components like the fuel system, cooling system, and transmission. The manual also includes fault codes to assist with troubleshooting.
New Holland T6.175 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.175 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
New Holland T6.165 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
New Holland T6.165 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab components, and more. Specific sections cover maintenance and repairs for components like the fuel system, cooling system, and transmission. The manual also includes fault codes to assist with troubleshooting.
New Holland T6.165 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.160 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.155 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab climate control and more. Repair procedures are organized by system with component level details provided. The manual is intended to be used as a technical reference for technicians servicing Case IH T6 tractors.
New Holland T6.155 Dynamic Command STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor including the engine, transmission, axles, hydraulics, electrical systems, cab components, and more. Specific sections cover maintenance and repairs for components like the fuel system, cooling system, and transmission. The manual also includes fault codes to assist with troubleshooting.
New Holland T6.155 AutoCommand™ STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
New Holland T6.145 STAGE IV Tractor Service Repair Manual.pdfnkikou1545
This service manual provides maintenance and repair information for Case IH T6 tractors models T6.125 through T6.180. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, electrical systems, and more. Each system section includes detailed information on components, operation, and repair procedures.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 6EW
Configuration: 962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754103
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Separate the torque converter from the transmission and from the output gears. Refer to
Disassembly and Assembly, "Torque Converter from Transmission, Output Gears -
Separate".
1/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00319444
1. Use Tooling (A) and a suitable lifting device to place torque converter housing (1) onto
suitable cribbing, as shown.
Illustration 2 g00319445
2. Remove transmission oil pump (2) . Refer to Disassembly and Assembly, "Transmission Oil
Pump - Remove".
3. Remove bolt (3) and washer (4) .
Illustration 3 g00319447
4. Remove torque converter speed sensor (5) .
2/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00319448
5. Remove bolts (6) that hold the torque converter to the torque converter housing.
Illustration 5 g00319449
6. Remove bolts (7) and pump drive flange (8) .
Illustration 6 g00319450
7. Remove bolt (9) that holds shaft (10) to the torque converter housing.
3/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00319451
8. Install Tooling (B) in pump drive gear (11) .
9. Lift pump drive gear (11) and drive gear shaft (10) . Lift drive gear shaft (10) out of the
torque converter housing bore.
10. Place the assembly to one side of the torque converter housing bore. Make sure that drive
gear shaft (10) is not in the torque converter housing bore.
Illustration 8 g00319453
11. Remove Tooling (B) from pump drive gear (11) .
12. Remove drive gear shaft (10) from pump drive gear (11) .
13. Remove bearing (12) from pump drive gear (11) .
4/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g03652939
14. Use Tooling (A) and a suitable lifting device to remove torque converter housing (1) . The
weight of torque converter housing (1) is approximately 113 kg (250 lb).
Illustration 10 g03652860
15. Turn torque converter housing (1) over to remove pump drive gear (11) .
Illustration 11 g00319455
5/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 16. Remove drive gear (13) .
Illustration 12 g00319456
17. Remove retaining ring (14) that holds output shaft (15) .
18. Use a soft faced hammer in order to free the bearing from the carrier assembly. Remove
output shaft (15) from the carrier assembly.
Illustration 13 g00319500
19. Remove seal ring (16) from output shaft (15) .
20. Use a suitable press to remove roller bearing (17) .
6/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00319458
21. Remove bolts (18) . Remove torque converter impeller (19) from the impeller housing.
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 22
through 28.
Illustration 15 g00877132
22. Turn impeller (20) to the opposite side.
23. Remove retaining ring (21) and spacer (22) from carrier shaft (23) .
24. Remove stator (24) .
7/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00877125
25. Remove retaining ring (25) and washer (26) from stator (24) . Repeat the procedure for the
opposite side of stator (24) .
Illustration 17 g00877126
Note: If necessary, Raise the temperature of the stator to a maximum temperature of 135 °C
(275 °F) for approximately 15 minutes.
26. Remove bearing race (27) , freewheel rollers (28) , freewheel springs (29) , and freewheel
cam (30) from stator (24) .
8/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00877129
27. Remove spacer (31) from impeller (20) .
Illustration 19 g00877133
28. Use a press to remove carrier shaft (23) from impeller (20) .
Illustration 20 g00877250
29. Remove bolts (32) and drive gear (33) from the torque converter impeller.
9/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00877257
30. Remove roller bearing (34) from torque converter impeller (19) .
Illustration 22 g00877258
31. Remove seal ring (36) from carrier assembly (35) .
32. If necessary, remove locating dowel (37) .
10/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g01146281
33. Remove ring (39A) . Remove retaining ring (38) and impeller cover (39) from impeller
housing (40) .
Illustration 24 g00877261
34. Use Tooling (C) in order to remove retaining ring (41) .
Illustration 25 g00877262
35. Remove bearing spacer (42) .
36. Remove O-ring seal (43) .
11/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00877263
37. Turn the impeller housing onto the opposite side. Remove turbine assembly (44) .
Illustration 27 g00877264
38. Remove bolts (45) . Separate turbine (46) from turbine hub assembly (47) .
39. If necessary, remove locating dowel (48) .
Illustration 28 g00877265
12/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 40. Remove roller bearing (49) from the impeller housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 23 10:36:14 UTC+0800 2020
13/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 6EW
Configuration: 962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754104
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Pliers 1
D - Loctite 536 -
Illustration 1 g00877265
1/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: The notch on roller bearing (49) must be aligned with locating dowel (48) .
1. Install roller bearing (49) .
Illustration 2 g00877264
2. Install locating dowel (48) in turbine hub assembly (38) .
3. Install turbine hub assembly (47) to turbine (46) . Install bolts (45) . The torque for bolts
(45) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 3 g00877263
4. Install the impeller housing over turbine assembly (44) , as shown.
2/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g00877262
5. Install O-ring seal (43) .
6. Install bearing spacer (42) .
Illustration 5 g00877261
7. Use Tooling (C) in order to install retaining ring (41) .
Illustration 6 g01146281
3/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install impeller cover (39) and retaining ring (38) in impeller housing (40) . Install ring
(39A) .
Illustration 7 g00877258
9. Install locating dowel (37) .
10. Install seal ring (36) on carrier assembly (35) .
Illustration 8 g00877257
Note: The notch in roller bearing (34) must be facing upward.
11. Install roller bearing (34) in torque converter impeller (19) .
4/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00877250
12. Install drive gear (33) and bolts (32) on the torque converter impeller. The torque for bolts
(32) is 105 ± 15 N·m (75 ± 11 lb ft).
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 13
through 18.
Illustration 10 g00877133
13. Use a suitable press to install carrier shaft (23) in impeller (20) .
5/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 11 g00877129
14. Install spacer (31) on impeller (20) .
Illustration 12 g00877126
Note: If necessary, Raise the temperature of stator (24) to a maximum temperature of 135 °
C (275 °F). Install the cam with the IMPELLER SIDE facing downward. Continue with the
installation until freewheel cam (30) contacts the retaining ring (not shown).
15. Install freewheel cam (30) , freewheel springs (29) , freewheel rollers (28) , and bearing race
(27) in stator (24) .
Note: Install freewheel springs (29) with the maximum number of loops toward the outside
diameter of freewheel cam (30) .
Illustration 13 g00877125
16. Install washer (26) and snap ring (25) on stator (24) . Repeat the procedure for the opposite
side of stator (24) .
6/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 14 g00877132
17. Install stator (24) on impeller (20) .
18. Install spacer (22) and snap ring (21) on carrier shaft (23) .
Illustration 15 g00319458
19. Install torque converter impeller (19) on the impeller housing.
20. Install bolts (18) . The torque for bolts (18) is 60 ± 7 N·m (44 ± 5 lb ft).
7/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 16 g00319500
21. Install roller bearing (17) on output shaft (15) .
22. Install seal ring (16) .
Illustration 17 g00319456
23. Install output shaft (15) in the carrier assembly.
24. Install retaining ring (14) that secures output shaft (15) .
Illustration 18 g00319455
25. Install drive gear (13) .
8/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 19 g03652860
26. Install pump drive gear (11) to the underside of torque converter housing (1) .
Illustration 20 g03652939
27. Install Tooling (A) and a suitable lifting device to install torque converter housing (1) onto
the torque converter assembly. The weight of torque converter housing (1) is approximately
113 kg (250 lb).
Illustration 21 g00319448
9/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 28. Install bolts (6) that hold the torque converter to the torque converter housing. The torque
for bolts (6) are 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 22 g00319453
29. Install bearing (12) and drive gear shaft (10) in pump drive gear (11) .
30. Install Tooling (B) on pump drive gear (11) .
Illustration 23 g00319451
31. Place the assembly in the original position. Make sure that drive gear shaft (10) is in the
torque converter housing bore.
32. Remove Tooling (B) from pump drive gear (11) .
10/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 24 g00319450
33. Install bolt (9) that holds shaft (10) to torque converter housing (1) . The torque for bolt (9)
is 105 ± 20 N·m (75 ± 15 lb ft).
Illustration 25 g00319449
34. Install pump drive flange (8) and bolts (7) . The torque for bolts (7) is 60 ± 7 N·m (44 ± 5 lb
ft).
Illustration 26 g00319447
11/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 35. Apply Tooling (D) to torque converter speed sensor (5) . Install torque converter speed
sensor (5) . Adjust the torque converter speed sensor in order to maintain an air gap of 0.71
± 0.18 mm (0.028 ± 0.007 inch). The torque for torque converter speed sensor (5) is 25 ± 5
N·m (18 ± 4 lb ft).
Illustration 27 g00319445
36. Install washer (4) and bolt (3) . The torque for bolt (3) is 105 ± 20 N·m (75 ± 15 lb ft).
37. Install transmission oil pump (2) . Refer to Disassembly and Assembly, "Transmission Oil
Pump - Install".
Illustration 28 g00319444
38. Install Tooling (A) and a suitable lifting device to torque converter housing (1) , as shown.
End By: Connect the torque converter to the transmission and to the output gears. Refer to
Disassembly and Assembly, "Torque Converter to Transmission, Output Gears - Connect".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 23 10:37:13 UTC+0800 2020
12/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...