1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It describes removing over 40 individual components in 38 steps, and installing them in reverse order over 29 steps.
3. Key components that must be removed include the transmission oil pump, torque converter speed sensor, various bolts and gears, and the turbine assembly, and reinstalled in the proper orientation.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for each fastener. Tools required include link brackets, eyebolts and retaining ring pliers.
This document provides assembly instructions for a torque converter in a 962G wheel loader. It outlines 40 steps to disassemble the torque converter into its individual components and 29 steps to reassemble it. Key components that are removed and installed include the torque converter housing, various gears, bearings, seals, and fasteners. Special tools are required for tasks like removing retaining rings.
This document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps for disassembly, removing components like the transmission oil pump, speed sensor, bolts, gears, shafts, bearings, seals, and housing. It then describes 18 steps for reassembly, showing how to install these same components in reverse order, like installing bearings, seals, gears, shafts, housing, and bolts, while applying loctite and torquing bolts to specifications. Tools required are also listed.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for the fasteners. Tools required include link brackets, eyebolts and retaining ring pliers.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...jfjkskefmsmem
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document provides very detailed technical instructions for taking apart and rebuilding the wheel loader's torque converter.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...ufjjjsekkemmd
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document is a service repair manual for maintenance technicians to service the machine's powertrain.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fujsejfjksekkkm
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fjjskekdmnsme
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for each fastener. Tools required include link brackets, eyebolts and retaining ring pliers.
This document provides assembly instructions for a torque converter in a 962G wheel loader. It outlines 40 steps to disassemble the torque converter into its individual components and 29 steps to reassemble it. Key components that are removed and installed include the torque converter housing, various gears, bearings, seals, and fasteners. Special tools are required for tasks like removing retaining rings.
This document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps for disassembly, removing components like the transmission oil pump, speed sensor, bolts, gears, shafts, bearings, seals, and housing. It then describes 18 steps for reassembly, showing how to install these same components in reverse order, like installing bearings, seals, gears, shafts, housing, and bolts, while applying loctite and torquing bolts to specifications. Tools required are also listed.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for the fasteners. Tools required include link brackets, eyebolts and retaining ring pliers.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...jfjkskefmsmem
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document provides very detailed technical instructions for taking apart and rebuilding the wheel loader's torque converter.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...ufjjjsekkemmd
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document is a service repair manual for maintenance technicians to service the machine's powertrain.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fujsejfjksekkkm
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fjjskekdmnsme
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
This document provides instructions for disassembling and assembling the right planetary and brake, power train oil pump, and power train oil pump components of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, including removing gears, discs, seals, and other parts. It then provides 22 steps for reassembling these components. It also provides instructions for removing and installing the power train oil pump, which involves disconnecting hoses and removing mounting bolts. Finally, it details 23 steps for disassembling the power train oil pump and 21 steps for reassembling it.
Caterpillar Cat D4E TRACK-TYPE TRACTOR (Prefix 77W) Service Repair Manual.pdffyhsejdkkdmmd3e
The document provides instructions for removing and installing a fuel filter base on a Caterpillar 3304B or 3306B engine. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting the fuel line from the fuel filter base, and removing two bolts and the fuel filter base from the fuel injection pump housing. The installation procedure instructs to install the fuel filter base with a new gasket if needed, connect the fuel line, and secure with two bolts. Proper cleanliness is emphasized when working with fuel system components.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdffyhsejdkkdmmd3e
This document provides instructions for removing and installing an alternator on a D4E track-type tractor with a 3304 engine. It describes disassembling the alternator by removing components like the regulator, capacitor, pulley, fan, screws, bearings, and rotor. It then describes reassembling the alternator by cleaning parts and reinstalling components in the reverse order of removal. A similar process is described for removing and installing a fuel priming pump and fuel filter base on 3304 and 3306 engines.
The documents provide instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, and disassembling and assembling the fuel transfer pump for a Caterpillar D5B track-type tractor. The procedures include removing bolts and hoses, installing new gaskets if needed, reconnecting lines, and priming the system once reassembled. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump and fuel filter base on a Caterpillar C9 industrial engine. Key steps include:
- Removing bolts and washers to access the fuel priming pump and remove it from the fuel filter base.
- Disconnecting hoses and sensors before removing bolts to access the fuel filter base.
- Reinstalling by reversing the removal steps, reconnecting hoses and sensors, and priming the fuel system.
The document also provides instructions for removing and installing a unit injector, including disconnecting electrical connectors, removing mounting bolts, and using special tools to access and remove the injector without damage. Reinstallation involves
This service repair manual provides instructions for removing and installing various fuel system components on a Caterpillar D4E track-type tractor with a 3304 engine, including:
1) The fuel priming pump, which is removed by turning off the fuel supply, removing securing bolts and disconnecting tubes. Installation is the reverse of removal.
2) The fuel filter base, which is removed by disconnecting the fuel line and removing securing bolts and washers. Installation includes checking and replacing gaskets if needed.
3) The fuel transfer pump, which is removed by turning off the fuel supply and removing securing bolts and tubes.
The document provides instructions for removing and installing a fuel priming pump on a Caterpillar D4E track-type tractor with a 3304 engine. It describes disconnecting fuel lines, removing mounting bolts and base, and reversing the steps for installation. Separate sections cover removing and installing the fuel filter base and removing the fuel transfer pump by disconnecting lines and removing mounting bolts.
The document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. It describes removing components like lines, covers, and bolts. It explains using tools like an impeller puller and spanner wrench. The assembly section describes cleaning parts, installing bearings, camshafts, and other components in the correct order and orientations.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap to connect fittings, removing and installing the muffler, removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing and installing the primary fuel filter base.
2) The procedures include identifying required tools, disconnecting lines and electrical connections, removing mounting hardware, and installing components in the reverse order of removal while taking appropriate safety precautions.
3) Detailed illustrations accompany each procedure to show component locations and the correct installation orientation. Torque specifications and lubrication requirements are provided where needed.
The document provides instructions for removing and installing fuel lines, filters, and pumps on a C32 industrial engine. It describes:
- Marking and removing existing fuel lines and replacing any worn or damaged lines.
- Installing new fuel lines according to best practices like preventing contact or twisting, using proper lengths and bends, and tightening securely.
- Removing the fuel filter and water separator by turning off fuel, using a strap wrench, and disconnecting hoses and bolts.
- Installing the fuel filter and water separator by reconnecting hoses and bolts, adding a new filter, and turning fuel back on.
- Removing the fuel transfer pump by turning off fuel
This document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine, including:
- The fuel priming pump, fuel filter base, fuel lines, and fuel transfer pump. Detailed step-by-step removal and installation procedures are provided along with required tools. Best practices are outlined for properly installing nonmetallic fuel lines.
This document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine BT4, including:
- The fuel priming pump, which involves disconnecting fuel lines and removing bolts.
- The fuel filter base, which requires disconnecting harness assemblies, hoses, and removing bolts to access sensors.
- Nonmetallic fuel lines, with details on marking, removing, and installing lines, using the proper hose length and avoiding contact with other parts.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing brackets, bolts, and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It involves the following steps:
1. Draining the coolant from the cooling system.
2. Using a strap wrench to remove the engine oil filter.
3. Disconnecting a hose assembly and removing bolts to take off the engine oil filter base and oil seal.
4. Removing the engine oil cooler and gasket.
The installation procedure is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Cleaning and installing replacement parts in the reverse order
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a 3054E industrial engine. It includes removal and installation procedures with required tools and safety notices. The procedures describe removing/installing the exhaust manifold gasket, setscrews, and turbocharger. For valves, it describes removing/installing the valve springs, retainers, keepers, and stem seals while ensuring the piston is at top dead center.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
This document provides instructions for disassembling and assembling the right planetary and brake, power train oil pump, and power train oil pump components of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, including removing gears, discs, seals, and other parts. It then provides 22 steps for reassembling these components. It also provides instructions for removing and installing the power train oil pump, which involves disconnecting hoses and removing mounting bolts. Finally, it details 23 steps for disassembling the power train oil pump and 21 steps for reassembling it.
Caterpillar Cat D4E TRACK-TYPE TRACTOR (Prefix 77W) Service Repair Manual.pdffyhsejdkkdmmd3e
The document provides instructions for removing and installing a fuel filter base on a Caterpillar 3304B or 3306B engine. The removal procedure involves using a strap wrench to remove the fuel filter, disconnecting the fuel line from the fuel filter base, and removing two bolts and the fuel filter base from the fuel injection pump housing. The installation procedure instructs to install the fuel filter base with a new gasket if needed, connect the fuel line, and secure with two bolts. Proper cleanliness is emphasized when working with fuel system components.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdffyhsejdkkdmmd3e
This document provides instructions for removing and installing an alternator on a D4E track-type tractor with a 3304 engine. It describes disassembling the alternator by removing components like the regulator, capacitor, pulley, fan, screws, bearings, and rotor. It then describes reassembling the alternator by cleaning parts and reinstalling components in the reverse order of removal. A similar process is described for removing and installing a fuel priming pump and fuel filter base on 3304 and 3306 engines.
The documents provide instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, and disassembling and assembling the fuel transfer pump for a Caterpillar D5B track-type tractor. The procedures include removing bolts and hoses, installing new gaskets if needed, reconnecting lines, and priming the system once reassembled. Safety notices are provided to keep parts clean and contain fluids during maintenance.
The document provides instructions for removing and installing a fuel priming pump and fuel filter base on a Caterpillar C9 industrial engine. Key steps include:
- Removing bolts and washers to access the fuel priming pump and remove it from the fuel filter base.
- Disconnecting hoses and sensors before removing bolts to access the fuel filter base.
- Reinstalling by reversing the removal steps, reconnecting hoses and sensors, and priming the fuel system.
The document also provides instructions for removing and installing a unit injector, including disconnecting electrical connectors, removing mounting bolts, and using special tools to access and remove the injector without damage. Reinstallation involves
This service repair manual provides instructions for removing and installing various fuel system components on a Caterpillar D4E track-type tractor with a 3304 engine, including:
1) The fuel priming pump, which is removed by turning off the fuel supply, removing securing bolts and disconnecting tubes. Installation is the reverse of removal.
2) The fuel filter base, which is removed by disconnecting the fuel line and removing securing bolts and washers. Installation includes checking and replacing gaskets if needed.
3) The fuel transfer pump, which is removed by turning off the fuel supply and removing securing bolts and tubes.
The document provides instructions for removing and installing a fuel priming pump on a Caterpillar D4E track-type tractor with a 3304 engine. It describes disconnecting fuel lines, removing mounting bolts and base, and reversing the steps for installation. Separate sections cover removing and installing the fuel filter base and removing the fuel transfer pump by disconnecting lines and removing mounting bolts.
The document provides instructions for removing and installing the fuel injection pump housing and governor of a Caterpillar 3304B engine. It describes removing components like lines, covers, and bolts. It explains using tools like an impeller puller and spanner wrench. The assembly section describes cleaning parts, installing bearings, camshafts, and other components in the correct order and orientations.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap to connect fittings, removing and installing the muffler, removing and installing the fuel priming pump, removing and installing the fuel filter base, and removing and installing the primary fuel filter base.
2) The procedures include identifying required tools, disconnecting lines and electrical connections, removing mounting hardware, and installing components in the reverse order of removal while taking appropriate safety precautions.
3) Detailed illustrations accompany each procedure to show component locations and the correct installation orientation. Torque specifications and lubrication requirements are provided where needed.
The document provides instructions for removing and installing fuel lines, filters, and pumps on a C32 industrial engine. It describes:
- Marking and removing existing fuel lines and replacing any worn or damaged lines.
- Installing new fuel lines according to best practices like preventing contact or twisting, using proper lengths and bends, and tightening securely.
- Removing the fuel filter and water separator by turning off fuel, using a strap wrench, and disconnecting hoses and bolts.
- Installing the fuel filter and water separator by reconnecting hoses and bolts, adding a new filter, and turning fuel back on.
- Removing the fuel transfer pump by turning off fuel
This document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine, including:
- The fuel priming pump, fuel filter base, fuel lines, and fuel transfer pump. Detailed step-by-step removal and installation procedures are provided along with required tools. Best practices are outlined for properly installing nonmetallic fuel lines.
This document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine BT4, including:
- The fuel priming pump, which involves disconnecting fuel lines and removing bolts.
- The fuel filter base, which requires disconnecting harness assemblies, hoses, and removing bolts to access sensors.
- Nonmetallic fuel lines, with details on marking, removing, and installing lines, using the proper hose length and avoiding contact with other parts.
This document provides instructions for disassembling and assembling components of the C27 Industrial Engine, including:
1) Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2) Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3) Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing brackets, bolts, and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height is achieved.
3) Valve seat inserts using an extractor tool and driver tools.
4) The engine oil filter base and related internal parts, noting any spring loaded components.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It involves the following steps:
1. Draining the coolant from the cooling system.
2. Using a strap wrench to remove the engine oil filter.
3. Disconnecting a hose assembly and removing bolts to take off the engine oil filter base and oil seal.
4. Removing the engine oil cooler and gasket.
The installation procedure is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Cleaning and installing replacement parts in the reverse order
The document provides instructions for removing and installing an exhaust manifold and inlet/exhaust valves on a 3054E industrial engine. It includes removal and installation procedures with required tools and safety notices. The procedures describe removing/installing the exhaust manifold gasket, setscrews, and turbocharger. For valves, it describes removing/installing the valve springs, retainers, keepers, and stem seals while ensuring the piston is at top dead center.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 6EW
Configuration: 962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754103
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Separate the torque converter from the transmission and from the output gears. Refer to
Disassembly and Assembly, "Torque Converter from Transmission, Output Gears -
Separate".
1/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00319444
1. Use Tooling (A) and a suitable lifting device to place torque converter housing (1) onto
suitable cribbing, as shown.
Illustration 2 g00319445
2. Remove transmission oil pump (2) . Refer to Disassembly and Assembly, "Transmission Oil
Pump - Remove".
3. Remove bolt (3) and washer (4) .
Illustration 3 g00319447
4. Remove torque converter speed sensor (5) .
2/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00319448
5. Remove bolts (6) that hold the torque converter to the torque converter housing.
Illustration 5 g00319449
6. Remove bolts (7) and pump drive flange (8) .
Illustration 6 g00319450
7. Remove bolt (9) that holds shaft (10) to the torque converter housing.
3/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00319451
8. Install Tooling (B) in pump drive gear (11) .
9. Lift pump drive gear (11) and drive gear shaft (10) . Lift drive gear shaft (10) out of the
torque converter housing bore.
10. Place the assembly to one side of the torque converter housing bore. Make sure that drive
gear shaft (10) is not in the torque converter housing bore.
Illustration 8 g00319453
11. Remove Tooling (B) from pump drive gear (11) .
12. Remove drive gear shaft (10) from pump drive gear (11) .
13. Remove bearing (12) from pump drive gear (11) .
4/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g03652939
14. Use Tooling (A) and a suitable lifting device to remove torque converter housing (1) . The
weight of torque converter housing (1) is approximately 113 kg (250 lb).
Illustration 10 g03652860
15. Turn torque converter housing (1) over to remove pump drive gear (11) .
Illustration 11 g00319455
5/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 16. Remove drive gear (13) .
Illustration 12 g00319456
17. Remove retaining ring (14) that holds output shaft (15) .
18. Use a soft faced hammer in order to free the bearing from the carrier assembly. Remove
output shaft (15) from the carrier assembly.
Illustration 13 g00319500
19. Remove seal ring (16) from output shaft (15) .
20. Use a suitable press to remove roller bearing (17) .
6/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00319458
21. Remove bolts (18) . Remove torque converter impeller (19) from the impeller housing.
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 22
through 28.
Illustration 15 g00877132
22. Turn impeller (20) to the opposite side.
23. Remove retaining ring (21) and spacer (22) from carrier shaft (23) .
24. Remove stator (24) .
7/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00877125
25. Remove retaining ring (25) and washer (26) from stator (24) . Repeat the procedure for the
opposite side of stator (24) .
Illustration 17 g00877126
Note: If necessary, Raise the temperature of the stator to a maximum temperature of 135 °C
(275 °F) for approximately 15 minutes.
26. Remove bearing race (27) , freewheel rollers (28) , freewheel springs (29) , and freewheel
cam (30) from stator (24) .
8/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00877129
27. Remove spacer (31) from impeller (20) .
Illustration 19 g00877133
28. Use a press to remove carrier shaft (23) from impeller (20) .
Illustration 20 g00877250
29. Remove bolts (32) and drive gear (33) from the torque converter impeller.
9/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00877257
30. Remove roller bearing (34) from torque converter impeller (19) .
Illustration 22 g00877258
31. Remove seal ring (36) from carrier assembly (35) .
32. If necessary, remove locating dowel (37) .
10/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g01146281
33. Remove ring (39A) . Remove retaining ring (38) and impeller cover (39) from impeller
housing (40) .
Illustration 24 g00877261
34. Use Tooling (C) in order to remove retaining ring (41) .
Illustration 25 g00877262
35. Remove bearing spacer (42) .
36. Remove O-ring seal (43) .
11/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00877263
37. Turn the impeller housing onto the opposite side. Remove turbine assembly (44) .
Illustration 27 g00877264
38. Remove bolts (45) . Separate turbine (46) from turbine hub assembly (47) .
39. If necessary, remove locating dowel (48) .
Illustration 28 g00877265
12/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 40. Remove roller bearing (49) from the impeller housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 23 10:36:14 UTC+0800 2020
13/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 6EW
Configuration: 962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754104
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Pliers 1
D - Loctite 536 -
Illustration 1 g00877265
1/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: The notch on roller bearing (49) must be aligned with locating dowel (48) .
1. Install roller bearing (49) .
Illustration 2 g00877264
2. Install locating dowel (48) in turbine hub assembly (38) .
3. Install turbine hub assembly (47) to turbine (46) . Install bolts (45) . The torque for bolts
(45) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 3 g00877263
4. Install the impeller housing over turbine assembly (44) , as shown.
2/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g00877262
5. Install O-ring seal (43) .
6. Install bearing spacer (42) .
Illustration 5 g00877261
7. Use Tooling (C) in order to install retaining ring (41) .
Illustration 6 g01146281
3/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install impeller cover (39) and retaining ring (38) in impeller housing (40) . Install ring
(39A) .
Illustration 7 g00877258
9. Install locating dowel (37) .
10. Install seal ring (36) on carrier assembly (35) .
Illustration 8 g00877257
Note: The notch in roller bearing (34) must be facing upward.
11. Install roller bearing (34) in torque converter impeller (19) .
4/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00877250
12. Install drive gear (33) and bolts (32) on the torque converter impeller. The torque for bolts
(32) is 105 ± 15 N·m (75 ± 11 lb ft).
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 13
through 18.
Illustration 10 g00877133
13. Use a suitable press to install carrier shaft (23) in impeller (20) .
5/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 11 g00877129
14. Install spacer (31) on impeller (20) .
Illustration 12 g00877126
Note: If necessary, Raise the temperature of stator (24) to a maximum temperature of 135 °
C (275 °F). Install the cam with the IMPELLER SIDE facing downward. Continue with the
installation until freewheel cam (30) contacts the retaining ring (not shown).
15. Install freewheel cam (30) , freewheel springs (29) , freewheel rollers (28) , and bearing race
(27) in stator (24) .
Note: Install freewheel springs (29) with the maximum number of loops toward the outside
diameter of freewheel cam (30) .
Illustration 13 g00877125
16. Install washer (26) and snap ring (25) on stator (24) . Repeat the procedure for the opposite
side of stator (24) .
6/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 14 g00877132
17. Install stator (24) on impeller (20) .
18. Install spacer (22) and snap ring (21) on carrier shaft (23) .
Illustration 15 g00319458
19. Install torque converter impeller (19) on the impeller housing.
20. Install bolts (18) . The torque for bolts (18) is 60 ± 7 N·m (44 ± 5 lb ft).
7/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 16 g00319500
21. Install roller bearing (17) on output shaft (15) .
22. Install seal ring (16) .
Illustration 17 g00319456
23. Install output shaft (15) in the carrier assembly.
24. Install retaining ring (14) that secures output shaft (15) .
Illustration 18 g00319455
25. Install drive gear (13) .
8/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 19 g03652860
26. Install pump drive gear (11) to the underside of torque converter housing (1) .
Illustration 20 g03652939
27. Install Tooling (A) and a suitable lifting device to install torque converter housing (1) onto
the torque converter assembly. The weight of torque converter housing (1) is approximately
113 kg (250 lb).
Illustration 21 g00319448
9/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 28. Install bolts (6) that hold the torque converter to the torque converter housing. The torque
for bolts (6) are 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 22 g00319453
29. Install bearing (12) and drive gear shaft (10) in pump drive gear (11) .
30. Install Tooling (B) on pump drive gear (11) .
Illustration 23 g00319451
31. Place the assembly in the original position. Make sure that drive gear shaft (10) is in the
torque converter housing bore.
32. Remove Tooling (B) from pump drive gear (11) .
10/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 24 g00319450
33. Install bolt (9) that holds shaft (10) to torque converter housing (1) . The torque for bolt (9)
is 105 ± 20 N·m (75 ± 15 lb ft).
Illustration 25 g00319449
34. Install pump drive flange (8) and bolts (7) . The torque for bolts (7) is 60 ± 7 N·m (44 ± 5 lb
ft).
Illustration 26 g00319447
11/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 35. Apply Tooling (D) to torque converter speed sensor (5) . Install torque converter speed
sensor (5) . Adjust the torque converter speed sensor in order to maintain an air gap of 0.71
± 0.18 mm (0.028 ± 0.007 inch). The torque for torque converter speed sensor (5) is 25 ± 5
N·m (18 ± 4 lb ft).
Illustration 27 g00319445
36. Install washer (4) and bolt (3) . The torque for bolt (3) is 105 ± 20 N·m (75 ± 15 lb ft).
37. Install transmission oil pump (2) . Refer to Disassembly and Assembly, "Transmission Oil
Pump - Install".
Illustration 28 g00319444
38. Install Tooling (A) and a suitable lifting device to torque converter housing (1) , as shown.
End By: Connect the torque converter to the transmission and to the output gears. Refer to
Disassembly and Assembly, "Torque Converter to Transmission, Output Gears - Connect".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 23 10:37:13 UTC+0800 2020
12/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...