This document provides instructions for disassembling and assembling various components of a Caterpillar 3304 vehicular engine used in a 955L track loader, including pistons, valves, cylinder liners, and more. The document outlines the start and end steps for removing and installing each component, and lists the specific procedures to disassemble, inspect, and reassemble the engine parts.
Caterpillar cat 955 l track loader (prefix 13x) service repair manual (13x000...udfjjjskekdme
This document provides instructions for disassembling and assembling various components of a Caterpillar 3304 vehicular engine used in a 955L track loader, including pistons, valves, cylinder liners, and more. The document outlines the start and end steps for removing and installing each component, and lists the specific procedures to disassemble, inspect, and reassemble the engine parts.
Caterpillar cat 120 h motor grader (prefix 5fm) service repair manual (5fm000...fusefjjskekemm
- The document provides instructions for removing and installing the camshaft on a 120H Motor Grader with a 3116 engine. It describes removing components like the governor and covers, then turning the crankshaft to align marks before removing the camshaft, gear, and bearings. Installation is the reverse of removal.
- Instructions are given to remove and install the camshaft gear by pressing it off the camshaft and heating it to 315°C before reinstalling.
- The procedure to remove and install camshaft bearings uses a special tool and orients the oil holes during installation.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 930 r wheel loader (prefix 57z) service repair manual (57z040...fujskekfmsme
This document provides instructions for installing the fuel injection pump housing and governor on a Caterpillar 930T wheel loader. It describes:
1) Using an engine turning tool to find the top center position of the No. 1 piston by turning the flywheel and installing a bolt in a hole in the flywheel.
2) Installing fuel pump timing pins and checking that the fuel injection pump gear teeth are aligned with the timing marks on the housing.
3) Installing the fuel injection pump housing and governor, and checking that the governor shaft turns freely once assembled.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and servicing components of a 436B backhoe loader engine, including:
1) Removing the cylinder head by first removing other components and then gradually loosening and removing 22 bolts.
2) Disassembling the rocker shaft by removing retaining rings and disassembling the shaft, arms, and brackets.
3) Reassembling the rocker shaft by lubricating parts and installing them in the correct order onto the shaft.
4) Installing the rocker shaft and pushrods by positioning them correctly and adjusting valve lash.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...uujfjjskkdme
This document provides installation instructions for auxiliary control valves on a 320C excavator in 3 steps:
1. Install the F1 and F4 auxiliary control valves together using existing mount bolts and connect hoses and electrical connections.
2. Connect pilot lines, electrical connectors, and tubes to both control valves and install panels and supports.
3. Install five pilot lines and covers to complete the installation.
Caterpillar cat 933 c hystat track loader (prefix 4ms) service repair manual ...fujskekfmsme
The document provides instructions for installing and removing an air inlet manifold and valves on a Caterpillar 3046 engine. It describes:
1) Using various tools to compress valve springs and remove caps and keepers to access the valves and springs.
2) Checking valve springs with a spring tester and specifications.
3) Installing new gaskets and bolting the air inlet manifold, elbow, and other components in multiple steps while checking for damage.
4) Maintaining air pressure in cylinders during valve spring removal and installation to hold valves in position.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 955 l track loader (prefix 13x) service repair manual (13x000...udfjjjskekdme
This document provides instructions for disassembling and assembling various components of a Caterpillar 3304 vehicular engine used in a 955L track loader, including pistons, valves, cylinder liners, and more. The document outlines the start and end steps for removing and installing each component, and lists the specific procedures to disassemble, inspect, and reassemble the engine parts.
Caterpillar cat 120 h motor grader (prefix 5fm) service repair manual (5fm000...fusefjjskekemm
- The document provides instructions for removing and installing the camshaft on a 120H Motor Grader with a 3116 engine. It describes removing components like the governor and covers, then turning the crankshaft to align marks before removing the camshaft, gear, and bearings. Installation is the reverse of removal.
- Instructions are given to remove and install the camshaft gear by pressing it off the camshaft and heating it to 315°C before reinstalling.
- The procedure to remove and install camshaft bearings uses a special tool and orients the oil holes during installation.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 930 r wheel loader (prefix 57z) service repair manual (57z040...fujskekfmsme
This document provides instructions for installing the fuel injection pump housing and governor on a Caterpillar 930T wheel loader. It describes:
1) Using an engine turning tool to find the top center position of the No. 1 piston by turning the flywheel and installing a bolt in a hole in the flywheel.
2) Installing fuel pump timing pins and checking that the fuel injection pump gear teeth are aligned with the timing marks on the housing.
3) Installing the fuel injection pump housing and governor, and checking that the governor shaft turns freely once assembled.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and servicing components of a 436B backhoe loader engine, including:
1) Removing the cylinder head by first removing other components and then gradually loosening and removing 22 bolts.
2) Disassembling the rocker shaft by removing retaining rings and disassembling the shaft, arms, and brackets.
3) Reassembling the rocker shaft by lubricating parts and installing them in the correct order onto the shaft.
4) Installing the rocker shaft and pushrods by positioning them correctly and adjusting valve lash.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...uujfjjskkdme
This document provides installation instructions for auxiliary control valves on a 320C excavator in 3 steps:
1. Install the F1 and F4 auxiliary control valves together using existing mount bolts and connect hoses and electrical connections.
2. Connect pilot lines, electrical connectors, and tubes to both control valves and install panels and supports.
3. Install five pilot lines and covers to complete the installation.
Caterpillar cat 933 c hystat track loader (prefix 4ms) service repair manual ...fujskekfmsme
The document provides instructions for installing and removing an air inlet manifold and valves on a Caterpillar 3046 engine. It describes:
1) Using various tools to compress valve springs and remove caps and keepers to access the valves and springs.
2) Checking valve springs with a spring tester and specifications.
3) Installing new gaskets and bolting the air inlet manifold, elbow, and other components in multiple steps while checking for damage.
4) Maintaining air pressure in cylinders during valve spring removal and installation to hold valves in position.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
This document provides instructions for removing and installing fuel injection lines and an automatic timing advance on a 3406 engine for a generator set. The steps include removing nuts and bolts to detach the lines and timing advance, cleaning surfaces, installing new gaskets, and tightening to the specified torques. Disassembly and assembly of the automatic timing advance and fuel transfer pump are also described in detail with accompanying diagrams.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat d11 t carrydozer track type tractor (prefix jns) service repa...fjkskmmdmme
The document provides instructions for disassembling a track roller frame on a D11T track-type tractor. It describes using straps and a hydraulic cylinder with a puller stud to remove the recoil spring and pilot assembly from the front of the track roller frame. It then explains how to remove various components from the track roller frame including the trunnion, plate, pin, and retainer assembly using lifting devices and tools. The overall purpose is to fully disassemble the track roller frame for repair or replacement of parts.
Caterpillar cat d11 t track type tractor (prefix jel) service repair manual (...fjkskmmdmme
The document provides instructions for disassembling and assembling the track roller frame of a D11T track-type tractor. It describes 16 steps to disassemble the frame, removing components like idlers, rollers, bogies, pins and plates. It then outlines 15 steps for reassembling the frame, providing details on cleaning, lubricating and torquing fasteners. Tools required include straps, hydraulic cylinders, pins and pullers to remove and install components.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing piston rings and connecting rod bearings on a Caterpillar 3306 engine. It describes the required tools and steps to disassemble pistons and connecting rods, including removing piston rings, piston pins, and bearings. It then explains how to assemble pistons and connecting rods, including cleaning parts, installing bearings, rings, piston pins, and connecting rods. Finally, it describes installing the pistons and connecting rods back into the engine.
Caterpillar cat 277 d multi terrain loader (prefix fmt) service repair manual...ufjjskekkmde
This service manual provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including the diesel particulate filter, inlet manifold, valve springs, valves, and valve guides. The procedures describe disconnecting hoses and sensors, removing mounting bolts, and installing components in the reverse order of removal while following torque specifications. Safety precautions are provided for hot and pressurized components.
Caterpillar cat 318 b excavator (prefix 3lr) service repair manual (3lr00001 ...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft, lifters, thrust plate and gear.
Toyota bt spe140 electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a forklift truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides procedures for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair and replacement instructions.
Toyota bt spe120 l electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides instructions for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair procedures.
Toyota bt spe120 electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides instructions for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair procedures.
Toyota bt reflex rre250 hecc high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt reflex rre250 hec high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt reflex rre250 he high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
This document provides a parts list for Massey Ferguson 8450/8460 Tractors (Tier 3) engines and equipment. It includes 51 numbered items with descriptions of parts like engines, starters, belts, fans, clutches, shields, brackets, bolts, nuts, and labels. The parts apply to various engine serial number ranges for the MF 8450 and 8460 models. Footnotes provide additional details on some parts.
This document provides a parts list for Massey Ferguson 8450/8460 Tractors (Tier 3) engines and equipment. It includes 51 numbered items with descriptions of parts like engines, starters, belts, fans, shields, nuts, bolts and other components. Part numbers, quantities, serial number ranges and other identifying information is provided for each part.
Massey ferguson mf8280 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine of Massey Ferguson 8270/8280 tractors. It includes 25 items describing cylinder block parts, their part numbers, and quantities. It also includes information on the cylinder block equipment with 22 additional parts listed. Finally, it describes the timing gear housing with 11 parts. The document provides detailed technical specifications and part numbers for various engine components.
Massey ferguson mf8270 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine of Massey Ferguson 8270/8280 tractors. It includes 25 items describing cylinder block parts, their part numbers, and quantities. It also includes information on the cylinder block equipment with 22 additional parts listed. Finally, it describes the timing gear housing with 23 parts and specifications. Overall, the document is a parts catalog for the engine, listing over 100 individual part numbers and descriptions to repair or replace components.
Massey ferguson mf8240 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for a Massey Ferguson 8240 tractor engine. It includes detailed lists of parts with part numbers, descriptions, quantities and other identifying information. The parts are grouped into sections covering the cylinder block, timing gear housing, flywheel housing, crankshaft and other engine components. The document contains replacement part numbers where original parts are no longer available.
Massey ferguson mf8220 tractors parts catalogue manualfjjskkdmnsme
This document provides a list of parts and descriptions for the engine and components of Massey Ferguson 8210/8220 tractors. It includes 41 items describing the cylinder block, 25 items for the crankshaft, pistons, and connecting rods, 33 items for the cylinder head, 14 items for the rocker shaft, and 10 items for the lubricating oil filler and breather system. Each item includes the part number, quantity, description, and any relevant comments.
Massey ferguson mf8210 tractors parts catalogue manualfjjskkdmnsme
This document provides a list of parts and descriptions for the engine and components of Massey Ferguson 8210/8220 tractors. It includes 41 items describing the cylinder block, 25 items for the crankshaft, pistons, and connecting rods, 33 items for the cylinder head, 14 items for the rocker shaft, and 10 items for the lubricating oil filler and breather system. Each item includes the part number, quantity, description, and any relevant comments.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
This document provides instructions for removing and installing fuel injection lines and an automatic timing advance on a 3406 engine for a generator set. The steps include removing nuts and bolts to detach the lines and timing advance, cleaning surfaces, installing new gaskets, and tightening to the specified torques. Disassembly and assembly of the automatic timing advance and fuel transfer pump are also described in detail with accompanying diagrams.
Caterpillar cat 16 g motor grader (prefix 93u) service repair manual (93u0267...fjsekdmmeed
This document provides instructions for removing and installing rocker shaft assemblies, push rods, valve lifters, and related components on a 3406C diesel engine. The key steps include:
1. Removing the valve covers, fuel lines, rocker shaft assemblies, push rods, and valve lifters. Identification marks should be made on removed parts.
2. Cleaning and lubricating replacement parts as needed before installation. Parts should be installed in their original locations when possible.
3. Installing the valve lifters, push rods, rocker shaft assemblies, fuel lines, adjusting the valves, and replacing the valve covers. Torque specifications and safety notices are provided throughout.
Caterpillar cat d11 t carrydozer track type tractor (prefix jns) service repa...fjkskmmdmme
The document provides instructions for disassembling a track roller frame on a D11T track-type tractor. It describes using straps and a hydraulic cylinder with a puller stud to remove the recoil spring and pilot assembly from the front of the track roller frame. It then explains how to remove various components from the track roller frame including the trunnion, plate, pin, and retainer assembly using lifting devices and tools. The overall purpose is to fully disassemble the track roller frame for repair or replacement of parts.
Caterpillar cat d11 t track type tractor (prefix jel) service repair manual (...fjkskmmdmme
The document provides instructions for disassembling and assembling the track roller frame of a D11T track-type tractor. It describes 16 steps to disassemble the frame, removing components like idlers, rollers, bogies, pins and plates. It then outlines 15 steps for reassembling the frame, providing details on cleaning, lubricating and torquing fasteners. Tools required include straps, hydraulic cylinders, pins and pullers to remove and install components.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing piston rings and connecting rod bearings on a Caterpillar 3306 engine. It describes the required tools and steps to disassemble pistons and connecting rods, including removing piston rings, piston pins, and bearings. It then explains how to assemble pistons and connecting rods, including cleaning parts, installing bearings, rings, piston pins, and connecting rods. Finally, it describes installing the pistons and connecting rods back into the engine.
Caterpillar cat 277 d multi terrain loader (prefix fmt) service repair manual...ufjjskekkmde
This service manual provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including the diesel particulate filter, inlet manifold, valve springs, valves, and valve guides. The procedures describe disconnecting hoses and sensors, removing mounting bolts, and installing components in the reverse order of removal while following torque specifications. Safety precautions are provided for hot and pressurized components.
Caterpillar cat 318 b excavator (prefix 3lr) service repair manual (3lr00001 ...fjskekdmjekm
1. The document provides instructions for removing and installing a camshaft on a 3046 engine used in 318B excavators.
2. The removal procedure involves using pullers to separate the camshaft gear and thrust plate from the camshaft and cylinder block.
3. The installation procedure specifies cleaning and lubricating parts, heating the camshaft gear, and aligning timing marks to ensure proper installation of the camshaft, lifters, thrust plate and gear.
Toyota bt spe140 electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a forklift truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides procedures for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair and replacement instructions.
Toyota bt spe120 l electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides instructions for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair procedures.
Toyota bt spe120 electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides instructions for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair procedures.
Toyota bt reflex rre250 hecc high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt reflex rre250 hec high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt reflex rre250 he high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
This document provides a parts list for Massey Ferguson 8450/8460 Tractors (Tier 3) engines and equipment. It includes 51 numbered items with descriptions of parts like engines, starters, belts, fans, clutches, shields, brackets, bolts, nuts, and labels. The parts apply to various engine serial number ranges for the MF 8450 and 8460 models. Footnotes provide additional details on some parts.
This document provides a parts list for Massey Ferguson 8450/8460 Tractors (Tier 3) engines and equipment. It includes 51 numbered items with descriptions of parts like engines, starters, belts, fans, shields, nuts, bolts and other components. Part numbers, quantities, serial number ranges and other identifying information is provided for each part.
Massey ferguson mf8280 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine of Massey Ferguson 8270/8280 tractors. It includes 25 items describing cylinder block parts, their part numbers, and quantities. It also includes information on the cylinder block equipment with 22 additional parts listed. Finally, it describes the timing gear housing with 11 parts. The document provides detailed technical specifications and part numbers for various engine components.
Massey ferguson mf8270 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine of Massey Ferguson 8270/8280 tractors. It includes 25 items describing cylinder block parts, their part numbers, and quantities. It also includes information on the cylinder block equipment with 22 additional parts listed. Finally, it describes the timing gear housing with 23 parts and specifications. Overall, the document is a parts catalog for the engine, listing over 100 individual part numbers and descriptions to repair or replace components.
Massey ferguson mf8240 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for a Massey Ferguson 8240 tractor engine. It includes detailed lists of parts with part numbers, descriptions, quantities and other identifying information. The parts are grouped into sections covering the cylinder block, timing gear housing, flywheel housing, crankshaft and other engine components. The document contains replacement part numbers where original parts are no longer available.
Massey ferguson mf8220 tractors parts catalogue manualfjjskkdmnsme
This document provides a list of parts and descriptions for the engine and components of Massey Ferguson 8210/8220 tractors. It includes 41 items describing the cylinder block, 25 items for the crankshaft, pistons, and connecting rods, 33 items for the cylinder head, 14 items for the rocker shaft, and 10 items for the lubricating oil filler and breather system. Each item includes the part number, quantity, description, and any relevant comments.
Massey ferguson mf8210 tractors parts catalogue manualfjjskkdmnsme
This document provides a list of parts and descriptions for the engine and components of Massey Ferguson 8210/8220 tractors. It includes 41 items describing the cylinder block, 25 items for the crankshaft, pistons, and connecting rods, 33 items for the cylinder head, 14 items for the rocker shaft, and 10 items for the lubricating oil filler and breather system. Each item includes the part number, quantity, description, and any relevant comments.
Massey ferguson mf8170 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine, alternator, starter, engine block heater, cylinder block, cylinder block equipment, timing gear housing, flywheel housing, crankshaft, pistons and connecting rods of a Massey Ferguson 8170 tractor with serial number 1637359. It contains lists of each component part number, quantity, description, and additional comments or specifications.
Massey ferguson mf8160 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for a Massey Ferguson 8160 tractor engine. It includes 3 pages listing 24 items that make up the cylinder block assembly, along with part numbers and descriptions. A second page lists 17 items that make up the cylinder head cover. The third page lists 26 items that make up the lubricating oil sump assembly.
Massey ferguson mf8150 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for an MF 8150 tractor engine. It includes 40 items describing engine parts like the cylinder block, pistons, crankshaft, timing gear housing, flywheel housing and other components. Each item lists the part number, quantity, description and any additional comments. It appears to be a parts catalog section for the engine of this tractor model.
Massey ferguson mf8140 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for an MF 8140 tractor engine. It includes a list of 39 engine parts with part numbers and quantities. The list includes major engine components like the cylinder block, crankshaft, pistons, connecting rods, timing gear housing, and flywheel housing. Footnotes provide additional details on some parts.
Massey ferguson mf8110 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, and turbocharger of a Massey Ferguson 8110 tractor with a T6.60 engine and serial number 1637281. It includes item numbers, part numbers, quantities, descriptions, and comments for 42 total parts related to these engine components. Replacement and repair notes are included for some parts indicating whether old parts are interchangeable with new updated part numbers.
Massey ferguson mf7726 s tractor (dyna vt) (f026053 9999999) or (m7726efn9s10...fjjskkdmnsme
This document provides a table of contents and part listings for a Massey Ferguson 7726/7726S tractor. The table of contents lists 18 systems for the tractor, including the engine/fuel system, axles, steering, drivetrain, brakes, hydraulics, electrical, and others. Following this are pages with detailed parts lists and descriptions for components of the engine cylinder block, timing gears/housing, and other engine assemblies. Over 50 individual parts are detailed on these pages.
Kobelco sk027 hydraulic excavator service repair manual sn pw01700 and upfjjskkdmnsme
The document is a shop manual issued in April 1992 for the hydraulic excavators SK024, SK027, and SK032. It provides applicable part numbers and model information for repairs and maintenance. The manual was first edition printed in the United States and copyrighted by Kobelco Construction Machinery America, LLC.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Valve Lifters, Pistons
SMCS - 1209-11; 1209-12; 1214-11
Remove Valve Lifters
start by:
a) remove cylinder head
1. Remove valve lifters (1) with magnet (2).
2. Put identification on each lifter for use at installation of the valve lifters.
Install Valve Lifters
1. Put clean engine oil on the valve lifters and camshaft lobes. Install the valve lifters in their
original positions in the cylinder block.
end by:
a) install cylinder head
Remove Pistons
1/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. start by:
a) remove cylinder head
b) remove oil pan plate
1. Remove the ring of carbon from the top inner surface of the cylinder liners.
2. Turn the crankshaft until two pistons are at bottom center. Remove connecting rod caps (1)
from the two connecting rods.
3. Put tape or pieces of rubber hose over the threads of the connecting rod bolts. This will prevent
damage to the crankshaft during removal of the pistons.
NOTICE
Do not let the connecting rods hit the bottom edge of the cylinder liners
or the crankshaft during removal and installation of the pistons.
TYPICAL EXAMPLE
4. Push the piston and connecting rod away from the crankshaft until the piston rings are above the
cylinder liner. Remove the two pistons (2) and the connecting rods from the engine.
5. Keep each connecting rod cap with its respective connecting rod and piston. Put identification
on each connecting rod as to its location in the engine for use at assembly of the engine.
2/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Do Steps 2 through 5 for the remainder of the pistons.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 17:55:22 UTC+0800 2019
3/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Pistons
SMCS - 1214-15; 1214-16; 1214-12
Install Pistons
TYPICAL EXAMPLE
1. Turn the crankshaft until the bearing journals for the pistons to be installed are at bottom center.
2. Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean
engine oil on the piston rings and connecting rod bearings.
3. Move the rings on the piston until the ring openings are approximately 90° apart.
NOTICE
Never install the ring compressor on the piston unless the cylinder liner
is used as a guide. Damage to the piston rings can be the result.
1/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 4. Put ring compressor (A) in position on the cylinder liner. Put the connecting rod and piston in
position in the same cylinder liner from which it was removed and into the ring compressor. Make
sure the "V" mark on the piston is in alignment with the "V" mark on the cylinder block.
5. Push the piston into place as the connecting rod is put into position on the crankshaft.
6. Put clean engine oil on bearings, bolt threads and surfaces of the nuts that make contact with the
connecting rod caps. Put caps (1) in position on the connecting rods and install the nuts. Tighten
the nuts to a torque of 30 ± 3 lb.ft. (40 ± 4 N·m). Put a mark on each nut and the end of each bolt.
Tighten the nuts 90° more.
NOTICE
When connecting rod caps are installed, make sure the number on the
side of the cap is next to and respective with the number on the side of
the connecting rod.
7. Follow the same above procedure for installation of the remainder of the pistons.
end by:
a) install oil pan plate
b) install cylinder head
2/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Disassemble Pistons
start by:
a) remove pistons
1. Remove rings from piston with tool (A).
2. Remove snap ring (3), piston pin (1) and connecting rod (2) from piston.
Assemble Pistons
NOTE: If a replacement of the rod pin is made, use a pin boring machine to make the bearing the
correct size.
3/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 1. Install rod on piston with bearing tab groove (2) and number identification on the same side as
the "V" mark (1) on top of piston.
2. Install piston pin and snap rings.
3. When the old pistons are used, clean the piston grooves with tool (A) before new piston rings
are installed.
4. Install rings on piston with tool (B). The ring openings must be 90° apart.
end by:
a) install pistons
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 17:56:22 UTC+0800 2019
4/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Valves
SMCS - 1105-12; 1105-11
Remove Valves
start by:
a) remove cylinder head
b) remove precombustion chambers
1. Put compression on valve spring (2) with tool (A) and remove locks (1).
2. Remove tool (A), rotocoil, spring and valve. Put identification on valves with respect to their
location in the cylinder head.
1/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Check the spring force with tool (B). The spring force is 57.7 ± 4.5 lb. (256.7 ± 20 N). The
length of spring under test force is 1.766 in. (44.86 mm). The free length after test is 2.05 in. (52.1
mm).
4. Do Steps 1 through 3 again for remainder of valves.
Install Valves
1. Put clean engine oil on valve stems. Install valve, spring and rotocoil in the cylinder head.
2. Put tool (A) in position on valve spring and install the locks (1).
Locks can be thrown from valve when compressor is released, if they
are not in their correct position on valve stem.
3. Remove tool (A) and hit the top of valve with a plastic hammer to be sure the locks are in their
correct position on valve.
4. Do Steps 1 through 3 again for remainder of valves.
2/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. end by:
a) install precombustion chambers
b) install cylinder head
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 17:57:21 UTC+0800 2019
3/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Valve Seat Inserts, Water Directors
SMCS - 1103-10; 1115-10
Remove And Install Valve Seat Inserts
start by:
a) remove valves
1. Remove valve seat insert with tool group (A).
2. Clean and remove burrs from the valve seat bore.
1/2955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 3. Install the new valve seat insert with tool group (A). Do not increase diameter of extractor in
valve seat insert when the insert is installed in the head.
4. Grind valve seat insert according to specifications given in SPECIFICATIONS SECTION.
end by:
a) install valves
Remove And Install Water Directors
start by:
a) remove cylinder heads
1. Remove old water directors (1) from the cylinder head.
2. Clean the cylinder head.
3. Install new water directors in the cylinder head. Install the directors so the hole in the directors
is in alignment with the "V" mark on cylinder head.
NOTE: For reconditioning of cylinder head see STMG FORM JEG02327.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 17:58:20 UTC+0800 2019
2/2955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Valve Guides, Cylinder Liners
SMCS - 1104-10; 1216-11
Remove And Install Valve Guides
start by:
a) remove valves
1. Remove valve guides from the cylinder head with tool (A).
2. Put clean engine oil on the outside diameter of the valve guide. Install valve guide (1) with tools
(A) and (B).
1/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. The inside diameter of the valve guides after installation must be .3734 ± .0010 in. (9.48 ± .025
mm).
end by:
a) install valves
Remove Cylinder Liners
start by:
a) remove pistons
1. Check to be sure that all coolant has been removed from the cylinder block.
2. Cover the crankshaft bearing journals before the cylinder liners are removed.
2/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. TYPICAL EXAMPLE
3. Remove the cylinder liner with tooling (A).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 17:59:20 UTC+0800 2019
3/3955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Cylinder Liners
SMCS - 1216-12
Install Cylinder Liners
1. Clean the cylinder liners and block.
2. Install the liners in the block without the O-ring seals.
3. Install tooling (A) and two 5/8"-11 NC bolts 4 1/2 in. long. Tighten the bolts evenly to 50 lb.ft.
(70 N·m).
1/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 4. Check the liner (projection) height with tool group (B) at four locations around the line to find
the average measurement. The difference between the four measurements must not be more
than .001 in. (0.03 mm).
5. The average measurement of liner (projection) height must be .0020 to .0056 in. (0.051 to 0.142
mm). The measurement between liners next to each other, must not be more than .001 in. (0.03
mm) difference.
NOTE: If the liner is turned in the bore, it can make a difference in the liner (projection) height.
2/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 6. If the liner (projection) height is not .0020 to .0056 in. (0.051 to .0142 mm), check the thickness
of the liner flange (1) and depth of the liner bor (2) in the block (3). The thickness of the liner
flange must be .4048 ± .0008 in. (10.282 ± 0.020 mm). The depth of the liner bore in block must
be .401 ± .001 in. (10.19 ± 0.03 mm).
NOTE: If the liner bore in the block is worn and the measurement is not correct, the liner bore can
be corrected with a cylinder block counterboring tool. See SPECIAL INSTRUCTIONS, Form
FM055228.
7. Put a mark on the liner and block so the liner can be installed in the same position from which it
was removed.
8. Install new seals (4) on the cylinder liners. Put liquid soap on the seals and in the bores in the
cylinder block.
NOTICE
3/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. The liners must be installed in the cylinder block immediately after
band (5) is installed. Make sure the marks on the liners and the
cylinder block are in alignment when the cylinder liners are installed.
9. Put clean SAE 30 oil on band (5) and install it on the liner as shown. Put clean SAE 30 oil on
the liner and install it immediately in the cylinder block with tool group (C).
end by:
a) install pistons
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 18:00:19 UTC+0800 2019
4/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Balancer Shafts
SMCS - 1220-11; 1220-12
Remove Balancer Shafts
start by:
a) remove timing gear cover
b) remove oil pump
TYPICAL EXAMPLE
1. Remove bolts (1), lock, and plate that hold the balancer shaft in the cylinder block.
2. Remove balancer shaft (2).
3. Remove the other balancer shaft with the same above procedure.
Install Balancer Shafts
1/2955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. TYPICAL EXAMPLE
1. Put clean engine oil on the balancer shaft. Put balancer shaft (1) in position in the cylinder
block. Install the plate, lock, and bolts that hold the balancer shaft in place.
NOTE: Make sure the balancer shaft timing is correct. See INSTALL OIL PUMP.
end by:
a) install oil pump
b) install timing gear cover
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 18:01:18 UTC+0800 2019
2/2955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Engine
SMCS - 1000-11; 1000-12
Remove Engine
start by:
a) remove radiator and guard
1. Remove the oil from the engine. Disconnect cables from the battery.
2. Disconnect fuel line (1) from the fuel filter base.
3. Disconnect governor control linkage (6) from the lever on the governor. Let the linkage be
along the engine.
4. Disconnect power cable (2) and ground cable (7) from the starting motor.
NOTE: Put a mark on all wires before they are removed for installation purposes.
5. Disconnect the wiring harness by:
a) Disconnect two wires (4) from the solenoid.
b) Disconnect double wire (5) from the alternator.
c) Disconnect wire (3) from the pressure switch.
1/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 6. Disconnect wires (8) and (9) from connectors in the rear of the engine.
7. Disconnect the two brackets that hold water temperature sensor (10) to the engine and
disconnect the water temperature sensor.
8. Remove eight bolts (11) and disconnect torque converter flange (13) from flexible joints (12).
9. Fasten a hoist to the engine. Remove two bolts (14) and washers from the front support.
Remove the bolts and washers that hold the engine in position in the rear.
10. Remove the engine from the chassis. Weight of the engine is 1850 lb. (839 kg).
Install Engine
1. Fasten a hoist and a chain to the front and rear lifting eyes.
2/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 2. Put the engine in position in the chassis. Make an alignment with the engine and transmission.
See FLEXIBLE DRIVE COUPLING in TESTING AND ADJUSTING. This information is in the
POWER TRAIN SECTION.
3. When the alignment is correct install flexible joints (1) to the torque converter flange and the
engine output flange. Tighten the retaining bolts to a torque of 80 ± 5 lb.ft. (110 ± 7 N·m).
4. When the engine to transmission alignment is correct tighten the engine mounting bolts as
follows:
a) Front mounting bolts: 460 ± 50 lb.ft. (624 ± 70 N·m).
b) Rear mounting bolts: 225 ± 30 lb.ft. (300 ± 40 N·m).
5. Connect power cable (3) and ground cable (5) to the starting motor.
6. Connect fuel line (2) to the fuel filter base.
7. Connect harness (4) by connection of wires to the correct terminals where marks of
identification were made.
8. Connect governor control linkage (6) to the lever as shown with a pin and cotter pin.
3/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 9. Connect wires (7) and (8) to connectors at the rear of the engine.
10. Put water temperature sensor (9) in position on the engine and install it. Connect two clips (10)
to the engine to hold the water temperature sensor in place.
11. Connect the battery cables to the battery. Fill the engine with oil to the correct level. See
LUBRICATION AND MAINTENANCE GUIDE.
end by:
a) install radiator and guard
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 18:02:17 UTC+0800 2019
4/4955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Shutdown SIS
Previous Screen
Product: TRACK LOADER
Model: 955L TRACK LOADER 13X
Configuration: 955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304 VEHICULAR ENGINE FOR 955L TRACK-TYPE LOADER
Media Number -SENR7675-00 Publication Date -01/08/1978 Date Updated -12/10/2001
Flywheel
SMCS - 1156-11; 1156-12
Remove Flywheel
start by:
a) remove engine
NOTE: Engine is removed from machine for better illustration for removal of flywheel.
1. Remove four flexible drive joints (1).
2. Disconnect lubrication tube (2) at the joint.
1/5955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 3. Remove eight bolts (4) from flexible drive flange (3). Remove the plug from the center of the
flange.
4. Install forcing screw (5) in center of flange (3) and remove the flange.
5. Remove the remainder of the lubrication tube and remove twelve bolts (6). Remove cover (7).
6. Remove two seals from the flywheel cover.
7. Remove five bolts (8) and locks from the flange assembly.
8. Install two forcing screws (10) in flange assembly (9) and remove the flange assembly.
2/5955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. 9. Loosen nine bolts (11). Remove two of the bolts and install two 5/8"-18 NF guide bolts.
10. Put a mark on the flywheel and crankshaft for the correct alignment at installation.
11. Install two forcing screws in the flywheel and move the flywheel away from the flange of the
crankshaft.
12. Install tool (A). Remove the flywheel (12). Weight of the flywheel is 65 lb. (29 kg).
Install Flywheel
1. Install two 5/8"-18 NF guide bolts in the flange of the crankshaft.
3/5955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. 2. Fasten a hoist to tool (A) on flywheel (1). Put the flywheel in position on the crankshaft. Make
sure the mark on the flywheel is in alignment with the mark on the crankshaft. Remove tool (A).
3. Install seven of the bolts that hold the flywheel in position. Remove the two guide bolts. Install
the other two bolts.
4. Put flange assembly (2) in position and install five bolts and locks to hold it in place.
5. Install the two seals in flywheel cover (3) with tooling (B). The first seal is pushed to the
bottom of the seat. The second seal is installed even with the top of the seat. Put 1P808 General
Purpose Grease between the two seals.
6. Install a new gasket on the flywheel housing if one is needed. Put flywheel cover (3) in position
and install the twelve bolts that hold the cover in place. Install section of the lubrication tube on
the cover.
4/5955L TRACK LOADER / POWER SHIFT / 13X00001-UP (MACHINE) POWERED ...
2019/9/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...