Caterpillar cat 906 h compact wheel loader (prefix sdh) service repair manual (sdh00001 and up)

Service Repair Manual
Models
906H COMPACT
WHEEL LOADER

Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 906H COMPACT WHEEL LOADER SDH
Configuration: 906H Wheel Loader SDH00001-UP (MACHINE) POWERED BY C3.4 IND Engine
Disassembly and Assembly
906H, 906H2, 907H, 907H2, 908H and 908H2 Compact Wheel Loaders Machine
Systems
Media Number -KENR5217-04 Publication Date -01/07/2017 Date Updated -26/07/2017
i02839373
Steering Frame Lock - Separate and Connect
SMCS - 7506-029
Separation Procedure
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
Connect the steering frame lock link between the front and rear frames
before working on machine. Secure clevis pin with locking pin.
Before operating the machine, fasten the steering frame lock link into
the stored position and secure the clevis pin with locking pin.
Failure to lock into the stored position before operating can result in loss
of steering.
1/3(W)
w
2019/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

Illustration 1 g01416219
1. Remove locking pin (1) and pin (2). Move steering frame lock (3) to the storage position.
2. Install pin (2) through the frame and through steering frame lock (3). Install locking pin (1).
Connection Procedure
Personal injury or death can result from machine articulation or
movement.
Machine frames can move and a person can be crushed.
Connect the steering frame lock link between the front and rear frames
before working on machine. Secure clevis pin with locking pin.
Before operating the machine, fasten the steering frame lock link into
the stored position and secure the clevis pin with locking pin.
Failure to lock into the stored position before operating can result in loss
of steering.
2/3(W)
w
2019/9/2

1. Remove locking pin (1) from pin (2).
2. Move steering frame lock (3) in position to the front frame. Install pin (2) and locking pin
(1). Locking pin (1).
Note: To align the pin bores, move the front loader frame.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 2 07:07:35 UTC+0800 2019
3/3(W)
w
2019/9/2

Shutdown SIS
Previous Screen
Systems
i05750795
System Pressure - Release
SMCS - 4250-553-PX; 4300-553-PX; 4350-553-PX; 5050-553-PX
Release Procedure
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered, oil is cool before
removing any components or lines. Remove the oil filler cap only when
the engine is stopped, and the filler cap is cool enough to touch with
your bare hand.
Hydraulic System
Hydraulic oil pressure can remain in the hydraulic system on this
machine after the engine and pump have been stopped. Serious injury
can result if this pressure is not released before any service is done on
the hydraulic system. In order to prevent possible injury, release the
hydraulic system pressure before working on any fitting, hose, or
hydraulic component.
1/4(W)
w
2019/9/2

Lower all work tools to the ground before service is started. If the
hydraulic system must be serviced, tested, or adjusted with the work
tool in the raised position, the work tool and lift cylinders must be
supported properly.
Always move the machine to a location away from the travel of other
machines. Be sure that other personnel are not near the machine when
the engine is running and tests or adjustments are being made.
1. Park the machine on a hard, smooth, level surface. The location should also be dry and free
of debris.
2. Permit only one operator on the machine. All other personnel should be kept away from the
machine.
3. If the machine is equipped with a ride control system, place the ride control system into
“Service”.mode. Refer to “Ride Control” in this Operation and Maintenance, "Operator
Controls" section.
4. Position the bucket or the work tool just above the ground at a slight downward angle. This
position will ensure that the head end of the lift cylinders is pressurized.
5. Engage the parking brake.
6. Turn the engine start switch to the OFF position.
7. When the engine has stopped, turn the engine start switch back to the ON position so the
pilot oil can reach the main valve.
8. Move the implement lockout switch to the UNLOCKED position.
2/4(W)
w
2019/9/2

9. Move the lift control lever to the FLOAT position and the tilt control lever to the TILT
BACK position at the same time. This action allows the bucket or the work tool to tilt back
while the boom is lowered.
The bottom of the bucket or the work tool should rest flat on the ground. The weight of the
linkage should be supported by the ground. The pressure from the head end of the lift
cylinders and from the ride control accumulator is now vented to the hydraulic tank.
10. When the bucket or the work tool has settled to the ground, move both control levers to the
HOLD position. Cycle the control levers through all positions several times in order to
purge any remaining pressure from the implement hydraulic system. This action will
completely drain the pilot accumulator.
12. Slowly loosen the hydraulic tank filler cap in order to release the pressure from the
hydraulic tank.
13. After all of the pressure has been released, tighten the hydraulic tank filler cap. The
hydraulic system pressure has now been released. Hydraulic lines and components can now
be removed.
Release Procedure (Steering System, Braking System, and Quick Coupler) (If
Equipped)
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Park the machine on a hard, smooth, level surface. The location should also be dry and free
of debris.
2. Lower the bucket to the ground and stop the engine.
3. Engage the parking brake.
5. Turn the steering wheel fully to the left and fully to the right several times to relieve the
pressure in the steering system.
3/4(W)
w
2019/9/2

6. Depress the brake pedal repeatedly in order to release any pressure in the braking system.
When no more resistance is felt and no pressure release is heard, the braking system, and
Quick Coupler pressure is released.
7. Slowly loosen the hydraulic tank filler cap in order to release the pressure from the
hydraulic tank.
8. After all of the pressure has been released, tighten the hydraulic tank filler cap. The
hydraulic system pressure has now been released. Hydraulic lines and components can now
be removed.
Mon Sep 2 07:08:30 UTC+0800 2019
4/4(W)
w
2019/9/2

Shutdown SIS
Previous Screen
Systems
i03659004
Fuel Tank - Remove
SMCS - 1273-011
Removal Procedure
Start By:
A. Remove the cab. Refer to Disassembly and Assembly, "Cab - Remove".
1. Drain the fuel from the fuel tank into a suitable container for storage or disposal. Refer to
Operation and Maintenance Manual for the correct procedure.
2. Remove bolts (1) . Remove cable assembly (2) from cover (3) and remove cover (3) .
1/3(W)
w
2019/9/2

3. Remove bolts (4) .
4. Disconnect hoses (5) from fuel tank (7) .
5. Disconnect harness assembly (6) from fuel tank (7) .
2/3(W)
w
2019/9/2

The fuel tank has been removed for photographic purposes.
6. Disconnect hose assemblies (9) . Ensure that all hose assemblies (9) have been
disconnected. Rotate pump (10) in order to remove fuel tank (7) .
7. Remove the nuts and straps (8) . Use two people and remove fuel tank (7) from the
machine. The weight of fuel tank (7) is approximately 25 kg (55 lb).
Mon Sep 2 07:09:25 UTC+0800 2019
3/3(W)
w
2019/9/2

Shutdown SIS
Previous Screen
Systems
i03659035
Fuel Tank - Install
SMCS - 1273-012
Installation Procedure
The fuel tank has been removed for photographic purposes.
1/3(W)
w
2019/9/2

1. Use two people and install fuel tank (7) in the machine. The weight of fuel tank (7) is
approximately 25 kg (55 lb). Install straps (8) and the nuts.
2. Reposition pump (10) for installation. Install the mounting bolts.
3. Connect hose assemblies (9) .
4. Connect harness assembly (6) to fuel tank (7) .
5. Connect hoses (5) to fuel tank (7) .
2/3(W)
w
2019/9/2

6. Install bolts (4) .
7. Install cable assembly (2) through cover (3) and install cover (3) . Remove bolts (1) .
End By: Install the cab. Refer to Disassembly and Assembly, "Cab - Install".
Mon Sep 2 07:10:20 UTC+0800 2019
3/3(W)
w
2019/9/2

Shutdown SIS
Previous Screen
Systems
i02845610
Hydraulic Tank - Remove
SMCS - 5056-011
Removal Procedure
Start By:
a. Remove the engine. Refer to Disassembly and Assembly, "Engine - Remove".
b. Remove the gear pump (hydraulic fan). Refer to Disassembly and Assembly, "Hydraulic
Fan - Remove".
1. Remove bolts (2) and shroud (1).
1/2(W)
w
2019/9/2

2. Remove bolts (4) and move plate (3) out of the way.
3. Remove bolts (5) from the hydraulic tank.
4. Loosen the clamp and disconnect hose (6) from the radiator.
5. Loosen the clamp and disconnect hose (7) from hydraulic oil tank (10).
6. Loosen the clamp and disconnect hose (11) from hydraulic oil tank (10).
7. Move harness assembly (9) out of the way.
8. Remove bolts (8) and hydraulic oil tank (10) from the machine.
Mon Sep 2 07:11:14 UTC+0800 2019
2/2(W)
w
2019/9/2

Shutdown SIS
Previous Screen
Systems
i02845614
Hydraulic Tank - Install
SMCS - 5056-012
Installation Procedure
1. Install hydraulic oil tank (10) in the machine and install bolts (8).
2. Reposition harness assembly (9).
3. Connect hose (11) to hydraulic oil tank (10) and tighten the clamp.
4. Connect hose (7) to hydraulic oil tank (10) and tighten the clamp.
5. Connect hose (6) to the radiator and tighten the clamp.
1/2(W)
w
2019/9/2

6. Install bolts (5) to the hydraulic oil tank.
7. Reposition plate (3) and install bolts (4).
8. Install shroud (1) and bolts (2).
End By:
a. Install the gear pump (hydraulic fan). Refer to Disassembly and Assembly, "Hydraulic Fan -
Install".
b. Install the engine. Refer to Disassembly and Assembly, "Engine - Install".
Mon Sep 2 07:12:09 UTC+0800 2019
2/2(W)
w
2019/9/2

Shutdown SIS
Previous Screen
Systems
i02867148
Gear Pump (Implement) (Steering) (Hydraulic Fan) -
Remove
SMCS - 1387-011-GT; 4306-011-GT; 5073-011-HFN; 5073-011-ZI; 5084-011-GT
Removal Procedure
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2019/9/2

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide"for tools and supplies to collect and contain fluids in
Caterpillar machines.
Dispose of all fluids according to local regulations.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1. Drain the hydraulic oil from the hydraulic oil tank into a suitable container for storage or
disposal. Refer to Operation and Maintenance Manual for the correct procedure.
2. Disconnect hose assembly (2), hose assembly (4), hose assembly (5), and hose assembly (6)
from gear pump (3).
3. Disconnect harness assembly (7) from gear pump (3).
4. Remove bolts (1) and remove gear pump (3).
Mon Sep 2 07:13:04 UTC+0800 2019
2/2(W)
w
2019/9/2

Shutdown SIS
Previous Screen
Systems
i02870251
Gear Pump (Implement) (Steering) (Hydraulic Fan) -
Disassemble
SMCS - 1387-015-GT; 4306-015-GT; 5073-015-HFN; 5073-015-ZI; 5084-015-GT
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
Start By:
a. Remove the gear pump. Refer to Disassembly and Assembly, "Gear Pump - Remove".
1/12(W)
w
2019/9/2

1. Remove bolts (1) and cover (2).
2/12(W)
w
2019/9/2

2. Remove seals (3) and bearing (4).
3/12(W)
w
2019/9/2

3. Remove gears (5), bearing (6), and seals (7).
4/12(W)
w
2019/9/2

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

4. Remove seal (8), housing (9), seal (10), plate (10A), and seal (11).
5/12(W)
w
2019/9/2

5. Remove seals (12) and bearing (13).
6/12(W)
w
2019/9/2

6. Remove gears (14), bearing (15), seals (17), and seal (16).
7/12(W)
w
2019/9/2

7. Remove housing (18) and seal (19).
8/12(W)
w
2019/9/2

Caterpillar cat 906 h compact wheel loader (prefix sdh) service repair manual (sdh00001 and up)

Recommended

Recommended

More Related Content

More from fujsefkskemm

More from fujsefkskemm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 906 h compact wheel loader (prefix sdh) service repair manual (sdh00001 and up)