This document provides instructions for removing the piston pump (hydrostatic) from a 904H Compact Wheel Loader. Key steps include:
1. Disconnecting all hydraulic hoses and electrical harnesses from the pump.
2. Attaching lifting tools to the pump and cab to support the pump during removal.
3. Removing mounting bolts to separate the pump from the loader.
Safety precautions are described for releasing hydraulic pressure before removal and handling the pump, which weighs approximately 45 kg.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
The document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions to release hydraulic pressure. The steps include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the 45 kg pump away from the machine. Personal injury can result from high pressure hydraulic fluid, so precautions are described.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
The document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions to release hydraulic pressure. The steps include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the 45 kg pump away from the machine. Personal injury can result from high pressure hydraulic fluid, so precautions are described.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes 7 steps to disconnect hoses and cables, attach lifting tools, and remove mounting bolts to lift the 45 kg piston pump out of the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...fujsefkskemm
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...uujjfjkkkdmme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the pump from the machine. Safety precautions are provided, such as ensuring all attachments are lowered and oil is cool before removal to avoid injury from hydraulic pressure. The piston pump weighs approximately 45 kg.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...ufjjdkkksmme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and wiring, attaching lifting tools to the pump, and removing mounting bolts. Personal injury precautions are noted due to hydraulic pressure. The pump weighs approximately 45 kg (100 lb) and must be lifted out of the machine once the bolts are removed.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...fujseskemmesd
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the pump from the machine. Safety precautions are provided, such as ensuring all attachments are lowered and oil is cool before removal to avoid injury from hydraulic pressure. The piston pump weighs approximately 45 kg.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...fjjskkdmnsme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes the 8 step process to disconnect hoses and cables, attach lifting tools to the pump and cab, and remove the mounting bolts to lift the 45 kg pump away from the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions to disassemble a piston pump used in a Caterpillar 904B compact wheel loader. It describes 33 steps to fully disassemble the pump and its components. Personal injury warnings are provided regarding hydraulic pressure and spring forces. Tools required are listed in a table. Detailed illustrations accompany each step to show how to remove parts like seals, shafts, plates, valves and more. Cleanliness is stressed to prevent contaminating internal parts during disassembly and reassembly.
This document provides instructions to disassemble a piston pump used in a Caterpillar 904B compact wheel loader. It describes 33 steps to fully disassemble the pump and its components. Personal injury warnings are provided regarding hydraulic pressure and spring forces. Tools required are listed in a table. Detailed illustrations accompany each step to show how to remove parts like seals, shafts, plates, valves and more. Cleanliness is stressed to prevent contaminating internal parts during disassembly and reassembly.
This document provides instructions to disassemble a piston pump used in a Caterpillar 904B compact wheel loader. It describes 33 steps to fully disassemble the pump and its components. Personal injury warnings are provided regarding hydraulic pressure and spring forces. Tools required are listed in a table. Detailed illustrations accompany each step to show how to remove parts like seals, shafts, plates, valves and more. Cleanliness is stressed to prevent contaminating internal parts during disassembly and reassembly.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fsejfjskefsmem
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It lists the required tools and outlines the step-by-step process which involves removing the V-belts, then removing and installing three bolts to take off or put on the crankshaft pulley. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fjksekkmsemm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to:
1) Remove bolts from the housing and remove the crankshaft rear seal, gasket, and housing from the cylinder block.
2) Clean parts and install the new crankshaft rear seal into the housing using a seal installer. Lubricate the seal and crankshaft, then position the housing over the crankshaft.
3) Install and tighten the bolts to secure the housing to the cylinder block. The document also provides instructions for installing the flywheel.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fusjejfskekfmsme
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It lists the required tools and describes the steps, which include removing the V-belts, taking out the three bolts holding the pulley, and installing the pulley using the bolts. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fujjsekskemme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to:
1) Remove bolts from the housing and remove the crankshaft rear seal, gasket, and housing from the cylinder block.
2) Clean parts and install the new crankshaft rear seal into the housing using a seal installer. Lubricate the seal and crankshaft, then position the housing over the crankshaft.
3) Install and tighten the bolts to secure the housing to the cylinder block. The document also provides instructions for installing the flywheel.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque range
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...fujsefkskemm
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It describes:
1) Disconnecting hoses, harnesses, and cables from the piston pump.
2) Attaching lifting tools to the piston pump and cab to aid in removal.
3) Removing mounting bolts to separate the piston pump from the mounting flange.
4) Lifting the 45 kg piston pump away once it is detached.
Personal safety precautions are outlined, and tools required are listed.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...uujjfjkkkdmme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the pump from the machine. Safety precautions are provided, such as ensuring all attachments are lowered and oil is cool before removal to avoid injury from hydraulic pressure. The piston pump weighs approximately 45 kg.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...ufjjdkkksmme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and wiring, attaching lifting tools to the pump, and removing mounting bolts. Personal injury precautions are noted due to hydraulic pressure. The pump weighs approximately 45 kg (100 lb) and must be lifted out of the machine once the bolts are removed.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...fujseskemmesd
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It outlines 11 steps, which include disconnecting hoses and harnesses, attaching lifting tools to the pump, and removing mounting bolts to lift the pump from the machine. Safety precautions are provided, such as ensuring all attachments are lowered and oil is cool before removal to avoid injury from hydraulic pressure. The piston pump weighs approximately 45 kg.
Caterpillar cat 904 h compact wheel loader service repair manual (h4t00001 an...fjjskkdmnsme
This document provides instructions for removing the piston pump from a 904H Compact Wheel Loader. It lists the required tools and safety precautions, then describes the 8 step process to disconnect hoses and cables, attach lifting tools to the pump and cab, and remove the mounting bolts to lift the 45 kg pump away from the machine. Personal injury can result from hydraulic pressure, so pressure must be released before removal.
This document provides instructions to disassemble a piston pump used in a Caterpillar 904B compact wheel loader. It describes 33 steps to fully disassemble the pump and its components. Personal injury warnings are provided regarding hydraulic pressure and spring forces. Tools required are listed in a table. Detailed illustrations accompany each step to show how to remove parts like seals, shafts, plates, valves and more. Cleanliness is stressed to prevent contaminating internal parts during disassembly and reassembly.
This document provides instructions to disassemble a piston pump used in a Caterpillar 904B compact wheel loader. It describes 33 steps to fully disassemble the pump and its components. Personal injury warnings are provided regarding hydraulic pressure and spring forces. Tools required are listed in a table. Detailed illustrations accompany each step to show how to remove parts like seals, shafts, plates, valves and more. Cleanliness is stressed to prevent contaminating internal parts during disassembly and reassembly.
This document provides instructions to disassemble a piston pump used in a Caterpillar 904B compact wheel loader. It describes 33 steps to fully disassemble the pump and its components. Personal injury warnings are provided regarding hydraulic pressure and spring forces. Tools required are listed in a table. Detailed illustrations accompany each step to show how to remove parts like seals, shafts, plates, valves and more. Cleanliness is stressed to prevent contaminating internal parts during disassembly and reassembly.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fsejfjskefsmem
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It lists the required tools and outlines the step-by-step process which involves removing the V-belts, then removing and installing three bolts to take off or put on the crankshaft pulley. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fjksekkmsemm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to:
1) Remove bolts from the housing and remove the crankshaft rear seal, gasket, and housing from the cylinder block.
2) Clean parts and install the new crankshaft rear seal into the housing using a seal installer. Lubricate the seal and crankshaft, then position the housing over the crankshaft.
3) Install and tighten the bolts to secure the housing to the cylinder block. The document also provides instructions for installing the flywheel.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fusjejfskekfmsme
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It lists the required tools and describes the steps, which include removing the V-belts, taking out the three bolts holding the pulley, and installing the pulley using the bolts. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fujjsekskemme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to:
1) Remove bolts from the housing and remove the crankshaft rear seal, gasket, and housing from the cylinder block.
2) Clean parts and install the new crankshaft rear seal into the housing using a seal installer. Lubricate the seal and crankshaft, then position the housing over the crankshaft.
3) Install and tighten the bolts to secure the housing to the cylinder block. The document also provides instructions for installing the flywheel.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque range
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It describes:
1. Removing the flywheel housing which requires removing other components first and using lifting tools.
2. Preparing the housing and cylinder block for installation by cleaning and applying sealant.
3. Installing the housing by positioning it with lifting tools, installing bolts, and tightening them in a specific sequence and torque.
Similar to Caterpillar Cat 904H COMPACT WHEEL LOADER Service Repair Manual (H4T00001 and UP).pdf (20)
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on an EL300 Excavator. The procedures include removing bolts, disconnecting tubes, and removing parts while taking precautions to contain fluids. Reinstallation involves cleaning parts, applying new gaskets or seals if needed, and reconnecting tubes before turning fuel valves back on. The fuel transfer pump section also provides instructions for disassembling and assembling the pump components.
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It outlines 22 steps for disassembly, including removing covers, plates, gears, and other components. It then outlines 45 steps for assembly, describing how to clean parts, install bearings and seals, measure clearances, and reassemble the gears, carriers, rings, and other parts in the reverse order of disassembly. The goal is to properly disassemble, measure, and reassemble the travel drive components.
Caterpillar Cat D4E TRACK-TYPE TRACTOR (Prefix 77W) Service Repair Manual.pdfzhaowo17360
The document provides instructions for disassembling and assembling an alternator. It describes removing components like the regulator, capacitor, pulley, fan, screws holding frames, rotor, bearings, slip ring, terminals, and stator. It then describes assembling these components in reverse order, making sure parts are clean and replacing any worn parts. The instructions are detailed with illustrations showing each step.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdfzhaowo17360
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304B or 3306B engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing bolts and disconnecting tubes. Reinstallation involves installing gaskets and bolts and turning the fuel supply back on.
- Removing the fuel filter base by using a strap wrench to remove the fuel filter, disconnecting fuel lines, and removing bolts and gaskets. Reinstallation involves installing new gaskets if needed and bolts.
- Procedures for removing the fuel transfer pump, which involves disconnecting fuel lines and electrical connections and removing mounting bolts.
The document provides instructions for removing and installing the fuel priming pump on a Caterpillar D4E track-type tractor. It lists the required tools and safety precautions before describing the removal process which involves turning off the fuel supply, removing securing bolts and hoses. The installation process is then described and involves reversing the removal steps and ensuring new gaskets are used if old ones are damaged.
The document provides instructions for removing and installing various fuel system components on a Caterpillar D4E track-type tractor powered by a 3304 engine. The components include the fuel priming pump, fuel filter base, and fuel transfer pump. Removal involves disconnecting connecting lines, removing mounting bolts and base, and taking note of gasket condition. Installation is the reverse of removal and includes checking and replacing worn gaskets. Disassembly of the fuel transfer pump is also described through removal of springs, seals, valves, piston, and housing pieces.
The document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The removal procedure involves disconnecting fuel lines and other components, removing mounting bolts and nuts, and lifting the housing and governor off the engine using two technicians or a lifting device. The installation procedure specifies cleaning and lubricating parts, inserting components in the correct order, and using tools to set timing and clearances.
This document provides instructions for removing and installing various components of a C32 Locomotive Engine, including:
1) The exhaust gas valve, involving removing seals, spools, and other parts before reassembly.
2) The exhaust elbow, requiring loosening clamps, sliding parts, and installing new components.
3) The catalyst, which is removed using lifting straps and reinstalled by aligning marks.
4) The air inlet elbow, involving disconnecting tubes, removing bolts, and replacing seals during reinstallation.
5) The inlet manifold, requiring removing brackets, clamps, and bolts before reversing the process to reinstall.
This document provides instructions for removing and installing fuel system components on a C32 Industrial Engine, including:
- Removing and installing nonmetallic fuel lines, noting best practices like proper hose length and avoiding contact with other surfaces.
- Removing the fuel filter and water separator, disconnecting hoses and electrical connections, and installing a new filter.
- Removing the fuel transfer pump by disconnecting hoses and removing mounting bolts, and installing the pump with a new O-ring seal.
The document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel lines
- Fuel transfer pump
- Fuel pressure regulator
The procedures include disconnecting fuel lines and electrical connections, removing mounting hardware, and installing components in reverse order. Proper torque specifications and safety precautions are listed for each component. Best practices are also outlined for installing nonmetallic fuel lines to prevent damage.
This document provides instructions for removing and installing fuel system components on a C32 Industrial Engine BT4, including:
- The fuel priming pump, fuel filter base, fuel transfer pump, and various fuel lines. Detailed step-by-step removal and installation procedures are provided along with required tools. Best practices are outlined for properly installing nonmetallic fuel lines.
- The document provides instructions for removing and installing inlet and exhaust valves on a 3054E Industrial Engine.
- Key steps include using a valve spring compressor tool to compress the valve spring, removing the valve keepers and spring retainer, and then removing the valve stem seal and valve.
- Installation involves cleaning parts, lubricating the valve stems, and installing the valves along with new stem seals, springs, retainers and keepers using the compressor tool. Taking care with spring loaded parts is emphasized for safety.
This document provides instructions for installing and removing a fuel injection pump on an industrial engine. It outlines the required tools and parts. The procedure describes checking the O-ring seal on the pump, lubricating it with oil, and installing the pump on the engine, ensuring proper timing. It notes to install a timing pin to check timing and remove any backlash in the gears. Finally, it describes installing fuel lines and the water pump once the fuel injection pump is installed.
This document provides instructions for removing and installing components on a Caterpillar 973C track loader engine, including:
- Removing and installing the turbocharger
- Removing and installing the exhaust manifold
- Removing and installing the air inlet heater
The instructions include lists of required tools and step-by-step procedures with illustrations. Safety notices are provided regarding keeping parts clean, containing fluids, and wearing protective equipment when working on the engine.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
The document provides instructions for removing and installing various components of a 963K track loader, including:
- Releasing hydraulic system pressure before removing any components or lines.
- Removing the ripper by detaching lift cylinders, removing bolts and pins, and lifting it off with a tool.
- Removing the ripper lift cylinder by disconnecting hoses and tubes, removing bolts and pins, and lifting it out.
- Removing the bucket by lowering the lift arm, releasing pressure, removing pins and bolts, and lifting the bucket off.
It outlines the required tools and provides step-by-step instructions for removing and installing each component safely.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 904H COMPACT WHEEL LOADER H4T
Configuration: 904H Wheel Loader H4T00001-UP (MACHINE) POWERED BY S4Q2T Engine
Disassembly and Assembly
904H Compact Wheel Loader Power Train
Media Number -KENR7636-01 Publication Date -01/10/2011 Date Updated -31/10/2011
i03132349
System Pressure - Release
SMCS - 4250-553-PX; 4300-553-PX; 4350-553-PX; 5050-553-PX
Release Procedure
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered, oil is cool before
removing any components or lines. Remove the oil filler cap only when
the engine is stopped, and the filler cap is cool enough to touch with
your bare hand.
1. Lower the implements to the ground.
2. Shut off the engine.
3. Turn the key to the ON position before moving control levers.
4. Move the control levers through the full range of travel in order to release the hydraulic
pressure.
5. Depress the brake pedal repeatedly in order to release the hydraulic pressure.
6. Slowly loosen the filler cap in order to release the tank pressure.
7. Tighten the filler cap.
1/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. 8. The pressure in the hydraulic system has been released. Lines and components can be
removed.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 6 14:52:48 UTC+0800 2019
2/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 904H COMPACT WHEEL LOADER H4T
Configuration: 904H Wheel Loader H4T00001-UP (MACHINE) POWERED BY S4Q2T Engine
Disassembly and Assembly
904H Compact Wheel Loader Power Train
Media Number -KENR7636-01 Publication Date -01/10/2011 Date Updated -31/10/2011
i03132299
Bottom Guard - Remove and Install
SMCS - 7153
Removal Procedure
Illustration 1 g01687014
1. Place Tooling (A) under bottom guard (2). Remove bolts (1). Remove bottom guard (2).
The weight of bottom guard (2) is approximately 18 kg (40 lb).
Installation Procedure
1/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 2 g01687014
1. Position bottom guard (2) on Tooling (A). Position bottom guard (2) and install bolts (1).
The weight of the bottom guard (2) is approximately 18 kg (40 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 6 14:53:36 UTC+0800 2019
2/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 904H COMPACT WHEEL LOADER H4T
Configuration: 904H Wheel Loader H4T00001-UP (MACHINE) POWERED BY S4Q2T Engine
Disassembly and Assembly
904H Compact Wheel Loader Power Train
Media Number -KENR7636-01 Publication Date -01/10/2011 Date Updated -31/10/2011
i03132305
Hydrostatic Pump Drive Mounting Hub and Flange -
Remove
SMCS - 3203-011-FLG; 3203-011-HU
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 4
Start By:
A. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydrostat) -
Remove".
Illustration 1 g01687706
1/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. 1. Install Tooling (A) to adapter plate (1). Remove adapter plate (1) .
Illustration 2 g01687707
2. Remove bolts (2) and flange (3) .
Illustration 3 g01687708
3. Loosen bolt (4) and remove hub (5) from piston pump (6) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 6 14:54:23 UTC+0800 2019
2/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 904H COMPACT WHEEL LOADER H4T
Configuration: 904H Wheel Loader H4T00001-UP (MACHINE) POWERED BY S4Q2T Engine
Disassembly and Assembly
904H Compact Wheel Loader Power Train
Media Number -KENR7636-01 Publication Date -01/10/2011 Date Updated -31/10/2011
i03132309
Hydrostatic Pump Drive Mounting Hub and Flange - Install
SMCS - 3203-012-FLG; 3203-012-HU
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 4
Illustration 1 g01687708
1. Position hub (5) on piston pump (6). Install bolt (4). Tighten bolt (4) to a torque of 55 ± 5
N·m (40.6 ± 3.7 lb ft).
1/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 2 g01687707
2. Install flange (3). Install bolts (2) .
Illustration 3 g01687706
3. Install Tooling (A) in order to install adapter plate (1) .
End By: Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydrostat) -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 6 14:55:11 UTC+0800 2019
2/2(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 904H COMPACT WHEEL LOADER H4T
Configuration: 904H Wheel Loader H4T00001-UP (MACHINE) POWERED BY S4Q2T Engine
Disassembly and Assembly
904H Compact Wheel Loader Power Train
Media Number -KENR7636-01 Publication Date -01/10/2011 Date Updated -31/10/2011
i03310024
Piston Pump (Hydrostatic) - Remove
SMCS - 3203-011-QP; 5070-011-H7
Removal Procedure
Table 1
Tool Part Number Description Quantity
A 140-7742 Sleeve 1
B
1U-9200 Ratchet 1
189-0410 Shackle 1
Start By:
A. Remove the seat. Refer to Disassembly and Assembly, "Seat - Remove".
B. Remove the gear pump. Refer to Disassembly and Assembly, "Gear Pump (Implement)
(Steering) (Hydraulic Fan) - Remove".
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1/5(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01689213
1. Disconnect hose assembly (2) and hose (3) from piston pump (1) .
2/5(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 4 g01167342
Illustration 5 g01167431
4. Attach Tooling (A) and Tooling (B) to the cab.
4/5(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 6 g01691014
5. Attach Tooling (B) and a suitable lifting device to piston pump (1) .
Illustration 7 g01691053
6. Remove mounting bolts (11) from piston pump (1). Remove piston pump (1). The weight of
piston pump (1) is approximately 45 kg (100 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 6 14:55:58 UTC+0800 2019
5/5(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 904H COMPACT WHEEL LOADER H4T
Configuration: 904H Wheel Loader H4T00001-UP (MACHINE) POWERED BY S4Q2T Engine
Disassembly and Assembly
904H Compact Wheel Loader Power Train
Media Number -KENR7636-01 Publication Date -01/10/2011 Date Updated -31/10/2011
i02338391
Piston Pump (Hydrostatic) - Remove
SMCS - 3203-011-QP; 5070-011-H7
Removal Procedure
Table 1
Tool Part Number Description Quantity
A 140-7742 Sleeve 1
B
1U-9200 Ratchet 1
189-0410 Shackle 1
C 242-6163 Wrench 1
Start By:
A. Remove the seat. Refer to Disassembly and Assembly, "Seat - Remove".
B. Remove the gear pump. Refer to Disassembly and Assembly, "Gear Pump - Remove".
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered, oil is cool before
removing any components or lines. Remove the oil filler cap only when
the engine is stopped, and the filler cap is cool enough to touch with
your bare hand.
1/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
Illustration 1 g01167299
1. Remove plate (1) .
2/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Illustration 2 g01167332
2. Disconnect harness assembly (2) .
Illustration 3 g01167334
3. Disconnect hose assemblies (3) and (4) from piston pump (5) .
3/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 4 g01167336
4. Disconnect hose assemblies (6) and (7) from piston pump (5) .
Illustration 5 g01167337
5. Disconnect hose assemblies (8) and (9) from piston pump (5) .
4/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 6 g01167341
6. Disconnect cable assembly (10) from piston pump (5). Disconnect hose assembly (11) from
piston pump (5) .
Illustration 7 g01167425
7. Disconnect hose assembly (12) from the bottom of piston pump (5) .
5/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 8 g01167342
Illustration 9 g01167431
8. Attach Tooling (A) and Tooling (B) to the cab.
6/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 10 g01167343
9. Attach Tooling (B) and a suitable lifting device to piston pump (5) .
Illustration 11 g01167344
10. Use Tooling (C) in order to remove mounting bolts (13) from piston pump (5) and mounting
flange (14) .
7/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Illustration 12 g01167346
11. Raise piston pump (5) in order to remove the pump from the machine. The weight of piston
pump (5) is approximately 45 kg (100 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 6 14:56:46 UTC+0800 2019
8/8(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 904H COMPACT WHEEL LOADER H4T
Configuration: 904H Wheel Loader H4T00001-UP (MACHINE) POWERED BY S4Q2T Engine
Disassembly and Assembly
904H Compact Wheel Loader Power Train
Media Number -KENR7636-01 Publication Date -01/10/2011 Date Updated -31/10/2011
i02327908
Piston Pump (Hydrostatic) - Disassemble
SMCS - 3203-015-QP; 5070-015-H7
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 1P-1861 Retaining Ring Pliers 1
C 5P-4758 Internal Pliers 1
D 1U-7600 Slide Hammer Puller 1
E 1P-1859 Retaining Ring Pliers 1
F 1P-1857 Retaining Ring Pliers 1
G 1S-4208 Spanner Wrench 1
Start By:
A. Remove the hydraulic drive pump. Refer to Disassembly and Assembly, "Hydraulic Drive
Pump - Remove".
Personal injury can result from hydraulic oil pressure and hot oil.
1/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
25. Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Dirt and contaminants can damage the components of the pump or the motor. All
disassembly and assembly procedures must be performed on a clean work surface. Clean all the
interior components in clean solvent. Dry all the interior components with compressed air. Plug
ports and plug hoses on the machine during repair.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00775547
1. Remove bolts (1) and remove charge pump (2) .
2/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 2 g00716074
Note: Mark the location of the charge pump on the head assembly. Crescent (M) of gear set
(4) must face toward the valves for installation purposes. The valves are indicated by
arrows.
2. Remove O-ring seal (3). Remove gear set (4). Keep the gear set together in order to ensure
proper installation of the gear set.
Illustration 3 g00580966
3. Remove bushing (5). Note the orientation of the bushing. The bushing must be installed in
the original location.
3/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. Illustration 4 g00580969
4. Remove plate (6). Note the position of the plate.
Illustration 5 g00580995
5. Remove shaft (7) and O-ring seal (8) .
Illustration 6 g00581004
6. Remove retaining ring (9) and key (10) from the shaft.
4/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
29. Illustration 7 g00581009
7. Remove bolts (11) and head assembly (12) .
Illustration 8 g00581016
8. Remove O-ring seals (13) and (14) from the head.
5/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
30. Illustration 9 g00581023
Illustration 10 g00581022
9. Use Tooling (A) in order to remove bushing (15) .
Illustration 11 g00581027
10. Remove bushing (16) .
Note: Mark orientation of groove in bushing (16) for later installation of new bushing into
the original location.
6/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
31. Illustration 12 g00794209
Note: Mark the position of the port plate for installation purposes. The groove in the port
plate must face the two valves on the head assembly.
11. Remove port plate (17) and bearing (18), if necessary.
Note: Perform Steps 12 and 13, if equipped.
Illustration 13 g00794067
12. Remove plug assembly (19) from the head.
7/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
32. Illustration 14 g00794187
13. Disassemble the plug assembly, as follows: O-ring seal (20), O-ring seal (21) and locking
plug (22) .
Illustration 15 g00722813
14. Remove valve (23) from the head.
8/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
33. Illustration 16 g00581200
15. Disassemble the valve, as follows: O-ring seal (26), backup ring (25) and O-ring seal (24) .
Illustration 17 g00581207
16. Remove valve (27) from the head. Refer to Step 15 for the disassembly procedure.
Illustration 18 g01162895
9/23(W)
w
2019/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...