The document provides instructions for removing and disassembling the implement pump on a 527 Track Skidder. It outlines 3 key steps:
1) Use a floor jack to support the implement pump and remove it from the machine by disconnecting hoses and removing nuts.
2) Disassemble the pump components including removing seals, springs, guides, plugs, cylinders and other internal parts.
3) Remove the swashplate assembly, bearings and seals from the pump housing. Detailed illustrations accompany each disassembly step.
This document provides instructions for disassembling and removing the implement pump from a Caterpillar 527 Track Skidder. It outlines 36 steps to fully disassemble the implement pump, including removing hoses, nuts, washers, compensator components, pistons, springs, seals, bearings and other parts. Safety notices are provided regarding relieving pressure in hydraulic systems and releasing spring tension during disassembly. Detailed illustrations accompany each step.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It details the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Many parts like pistons, springs and seals must be removed and installed carefully. Safety precautions are provided to relieve pressure before working on hydraulic components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures in detail with illustrations. Safety notices are included to release pressure from the hydraulic system before removal and to relieve spring tension carefully during disassembly. The multi-page document thoroughly explains each step to disassemble and reassemble the implement pump.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions then describe cleaning and installing parts like seals, springs, bearings and swashplate in reverse order of disassembly. Safety notices are included to relieve pressure before removing lines or components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions specify cleaning parts and installing new seals before reassembling components like the barrel assembly, swashplate and housing. Safety notices are included to relieve pressure before removing lines or components.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...cdfvvv1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...paws21610697
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. It details 27 steps to disassemble the travel motor involving removing plates, barrels, pistons, gears, seals, and other components. It then lists 27 steps for reassembling the travel motor, applying sealant and torque specifications where needed and noting the importance of cleanliness during assembly.
This document provides instructions for disassembling and removing the implement pump from a Caterpillar 527 Track Skidder. It outlines 36 steps to fully disassemble the implement pump, including removing hoses, nuts, washers, compensator components, pistons, springs, seals, bearings and other parts. Safety notices are provided regarding relieving pressure in hydraulic systems and releasing spring tension during disassembly. Detailed illustrations accompany each step.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It details the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Many parts like pistons, springs and seals must be removed and installed carefully. Safety precautions are provided to relieve pressure before working on hydraulic components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures in detail with illustrations. Safety notices are included to release pressure from the hydraulic system before removal and to relieve spring tension carefully during disassembly. The multi-page document thoroughly explains each step to disassemble and reassemble the implement pump.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions then describe cleaning and installing parts like seals, springs, bearings and swashplate in reverse order of disassembly. Safety notices are included to relieve pressure before removing lines or components.
This document provides instructions for removing and installing an implement pump on a 527 track skidder. It outlines the disassembly and assembly procedures, including removing hoses and nuts to remove the pump. Detailed steps are provided to disassemble the pump components like the compensator, head, cylinders and pistons. Assembly instructions specify cleaning parts and installing new seals before reassembling components like the barrel assembly, swashplate and housing. Safety notices are included to relieve pressure before removing lines or components.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...cdfvvv1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...jdjkskmikdkmd
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...paws21610697
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. It details 27 steps to disassemble the travel motor involving removing plates, barrels, pistons, gears, seals, and other components. It then lists 27 steps for reassembling the travel motor, applying sealant and torque specifications where needed and noting the importance of cleanliness during assembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...uddksemd8ud
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f7djidksmd3e
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...yan77xunhao
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing tracks and sprockets, and then disconnecting hoses and removing bolts to take the travel motor off the undercarriage frame. Disassembly of the travel motor includes removing plates, barrels, pistons, gears, shafts, seals and other components. Reassembly follows the reverse order and notes to replace seals, apply oil, and ensure cleanliness.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f8usiedkdmm
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Safety notices are provided to keep parts clean and contain fluids properly during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Precautions are given to keep parts clean and contain fluids during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety notices are also provided.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix WTZ) Service Repair Manu...yin9niaojiao
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides notes on proper installation of springs, seals, and ensuring alignment of keys and notches. Tools required include a transmission repair stand, lifting eyes, bolts, drivers and pullers. Personal protective equipment is recommended when working with springs.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336E LH and 336E LNH Excavator (Prefix GNY) Service Repair Ma...yin9niaojiao
The document provides instructions for removing and installing a travel motor on an excavator. It is a 28-step procedure that includes draining oil, removing hoses and fittings, using lifting devices to remove the final drive and travel motor assembly, and reinstalling the components in reverse order. Precautions are provided for working with pressurized hydraulic systems and heavy components. The installation steps specify applying anti-seize compound to bolts and torquing them to the specified values.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are provided to prevent injury from spring forces and ensure proper alignment of parts.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FAJ) Service Re...yin9niaojiao
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix NAH) Service Repair ...yin9niaojiao
This document provides the disassembly and assembly procedures for a travel motor on a Cat 336D2 excavator model. It lists 30 steps for disassembly, removing components like caps, springs, valves, plugs and seals. It then lists 30 steps for assembly, installing components like seals, pistons, bearings, springs and covers in the reverse order of disassembly. The document provides illustrations and notes for each step to ensure correct reassembly.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FBT) Service Re...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...yin9niaojiao
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix MYG) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout to prevent injury from spring loaded parts.
More Related Content
Similar to Caterpillar Cat 527 TRACK SKIDDER (Prefix PTR) Service Repair Manual Instant Download.pdf
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...uddksemd8ud
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f7djidksmd3e
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. O-rings, seals, gears and other internal components are also dismantled from the motor housing. Detailed illustrations accompany each step for complete disassembly of the travel motor.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dsa) service repair m...fikskkdmmd1
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves removing plates, barrels, pistons, springs, gears and other components using various tools. Detailed steps and illustrations are provided to label parts and ensure correct reassembly.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...yan77xunhao
The document provides instructions for removing and assembling the travel motor on a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing tracks and sprockets, and then disconnecting hoses and removing bolts to take the travel motor off the undercarriage frame. Disassembly of the travel motor includes removing plates, barrels, pistons, gears, shafts, seals and other components. Reassembly follows the reverse order and notes to replace seals, apply oil, and ensure cleanliness.
Caterpillar Cat 305CR Mini Hydraulic Excavator (Prefix DSA) Service Repair Ma...f8usiedkdmm
The document provides instructions for removing and disassembling the travel motor from a 305CR Mini Hydraulic Excavator. The removal process involves releasing hydraulic pressure, removing the track and final drive sprocket. Disassembly involves marking parts, draining oil, removing plates, barrels and pistons. Multiple gears, shafts, seals and other internal components are then dismantled from the travel motor housing.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Safety notices are provided to keep parts clean and contain fluids properly during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. The procedures include removing mounting bolts and studs, disconnecting air lines, and using valve spring compressors. Precautions are given to keep parts clean and contain fluids during maintenance. Diagrams illustrate the component locations and sequences.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety notices are also provided.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, disconnecting connections, removing gaskets and guides, and installing with new gaskets in the reverse order while applying sealant and torqueing fasteners to the specified values. Tools and safety precautions are also listed.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, inlet and exhaust valves, and inlet and exhaust valve guides on a 325, 325L, 325LN excavator with a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
Similar to Caterpillar Cat 527 TRACK SKIDDER (Prefix PTR) Service Repair Manual Instant Download.pdf (12)
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix WTZ) Service Repair Manu...yin9niaojiao
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides notes on proper installation of springs, seals, and ensuring alignment of keys and notches. Tools required include a transmission repair stand, lifting eyes, bolts, drivers and pullers. Personal protective equipment is recommended when working with springs.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336E LH and 336E LNH Excavator (Prefix GNY) Service Repair Ma...yin9niaojiao
The document provides instructions for removing and installing a travel motor on an excavator. It is a 28-step procedure that includes draining oil, removing hoses and fittings, using lifting devices to remove the final drive and travel motor assembly, and reinstalling the components in reverse order. Precautions are provided for working with pressurized hydraulic systems and heavy components. The installation steps specify applying anti-seize compound to bolts and torquing them to the specified values.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are provided to prevent injury from spring forces and ensure proper alignment of parts.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FAJ) Service Re...yin9niaojiao
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix NAH) Service Repair ...yin9niaojiao
This document provides the disassembly and assembly procedures for a travel motor on a Cat 336D2 excavator model. It lists 30 steps for disassembly, removing components like caps, springs, valves, plugs and seals. It then lists 30 steps for assembly, installing components like seals, pistons, bearings, springs and covers in the reverse order of disassembly. The document provides illustrations and notes for each step to ensure correct reassembly.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FBT) Service Re...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...yin9niaojiao
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix MYG) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout to prevent injury from spring loaded parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...yin9niaojiao
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components. Temperatures must be controlled for some parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar Cat 330F and 330F LN Excavator (Prefix HBT) Service Repair Manual...yin9niaojiao
This document provides instructions for removing and installing components related to the crankshaft and front cover of a Caterpillar 330F excavator engine. The procedures include removing and installing the crankshaft pulley, vibration damper, front seal, and heavy duty front cover. Tools required are listed for each procedure. Illustrations show the components and steps to disassemble and reassemble the assemblies.
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble components like pistons, gears, brackets, hoses and sensors. Tools include lever pullers, link brackets and torque wrenches. Precautions are given for spring loaded parts. The process involves lifting heavy components and ensuring proper hose, harness and bracket connections.
Caterpillar Cat 336D and 336D L Excavator (Prefix WRK) Service Repair Manual ...yin9niaojiao
The document provides instructions for removing and installing a final drive and travel motor on a Caterpillar 336D excavator. It lists required tools and gives step-by-step instructions involving disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix HER) Service Repair Manua...yin9niaojiao
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for removing and installing the rear gear group and related components on a 330D L excavator with a C9 engine. The removal process involves using tools to remove bolts, gears, bushings, bearings, and covers. The installation process gives specifics on cleaning parts, applying adhesives, inserting bearings at the proper angles and depths, and torquing bolts. Tolerances are provided for correct installation of several components.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual Instant D...yin9niaojiao
The document provides installation instructions for a swivel on an excavator. It describes removing the swivel by disconnecting hoses, removing bolts and lifting it out. It then details assembling the swivel by cleaning parts, installing seals and O-rings, positioning the housing over the rotor, and securing them with bolts. Finally, it describes installing the assembled swivel by connecting hoses and fittings and securing it with bolts.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix FEX) Service Repair Manua...yin9niaojiao
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components weighing up to 550 kg during disassembly. Cleanliness is important to prevent dirt from entering internal mechanisms.
The document provides instructions for disassembling the final drive of a 330D MH EXCAVATOR. It lists 31 steps to completely disassemble the final drive assembly including removing gears, carriers, shafts, seals and housings. Various tools are required including retaining ring pliers, link brackets, eyebolts and forcing bolts to separate the components. Cleanliness is important to prevent dirt from entering during disassembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014257
Implement Pump - Remove
SMCS - 5084-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
1/3
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Use the following procedure to release the pressure in the hydraulic system:
a. Lower the implements to the ground.
b. Shut off the engine.
c. Move the control levers through the full travel distance of the levers. This will relieve
any pressure in the pilot system.
d. Slowly loosen the filler cap on the hydraulic oil tank in order to release the pressure.
e. Tighten the filler cap on the hydraulic oil tank.
f. The pressure in the hydraulic system has now been relieved. Lines and components
can now be removed.
Note: Put identification on all lines, hoses, wires, and tubes for installation purposes.
Install a cap or plug on all lines, hoses, and tubes that are disconnected. The caps
and/or plugs prevent the loss of fluid and contaminants cannot enter the system.
Illustration 1 g00619640
1. The weight of the rear bottom guard is 70 kg (155 lb). Use a floor jack to support the guard.
Remove bolts (1) and rear bottom guard (2) .
2/3
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00619642
2. Disconnect hose assemblies (3), (4), (5), and (6) from the implement pump.
Illustration 3 g00619647
3. The weight of the implement pump is 33 kg (73 lb). Use a floor jack to support the pump.
4. Remove four nuts (7), the washers, and the implement pump from the machine.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:18:49 UTC+0800 2019
3/3
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014260
Implement Pump - Disassemble
SMCS - 5084-015
Disassembly Procedure
Start By:
A. Remove the implement pump.
Table 1
Required Tools
Tool Part Number Description Qty
A 1P-1858 Pliers 1
B 1P-0074 Slide Hammer Puller 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Be sure that the outside of the implement pump is clean prior to disassembly.
Illustration 1 g00619940
2. Remove O-ring seal (1) from pump (2) .
Illustration 2 g00619942
3. Remove bolts (4) and compensator (3) from the pump.
2/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g00619947
Typical example
4. Remove plug (6), plug (8), spool (5), and spool (7) from compensator (3) .
Illustration 4 g00619949
Typical example
5. Remove locknuts (9) and (10) .
Illustration 5 g00619950
Typical example
6. Remove margin plug (15), guide (14), spring stop pin (13), spring (12), and guide (11) from
compensator (3) .
7. Remove screw (16) from margin plug (15) .
3/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 6 g00619952
Typical example
8. Remove compensator plug (21), guide (20), spring (19), and guide (18) from the
compensator.
9. Remove screw (22) from compensator plug (21) .
10. Remove plug (17) and the O-ring seal from the compensator.
11. Remove O-ring seals (23) from the compensator.
Illustration 7 g00619953
Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
4/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: A spring is held in compression by the head. The pump head can be pushed away
from the pump case very rapidly. The spring tension must be released before the last bolt is
removed from the head. In order to gradually release the spring tension, be sure that the
head moves away from the pump case as the bolts are loosened. The bolts in the head are
long enough to release all of the tension in the spring before the bolts are removed.
12. Remove bolts (25) and head (24) from pump (2) .
Illustration 8 g00619954
13. Remove cylinder (26) from head (24). Also remove the spacer under cylinder (26) .
14. Remove cylinder (27) and spring (28) .
Illustration 9 g00619956
15. Note the location of plate (29) and remove the plate.
5/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 10 g00619958
16. Remove pistons (30) and (31). Remove the O-ring seal from each of the pistons.
17. Remove bearing cup (32) .
18. If necessary, remove pin (33) .
Illustration 11 g00619959
19. Remove gasket (34) from pump (2) .
20. Remove bolts (35), cover (36), and the O-ring seal.
6/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 12 g00619962
21. Remove bearing cone (37) from the shaft.
22. Remove plug (38) and the O-ring seal.
Illustration 13 g00619963
23. Remove spacer (39) from the shaft.
Illustration 14 g00619964
7/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 24. Remove barrel assembly (40) from pump (2) .
Illustration 15 g00619965
Illustration 16 g00619966
Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
25. Use a press to compress spring (44). Use Tool (A) to remove snap ring (43) from the groove
in barrel (40) .
26. Slowly release the compression on spring (44) .
27. Remove guide (42), spring (44), and guide (41) from barrel (40) .
8/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: Guides (41) and (42) are a different size. Mark the guides for assembly purposes.
Illustration 17 g00619968
28. Remove shaft (45) from pump (2) .
Illustration 18 g00620030
29. Tilt swashplate (46), and pistons (47). Remove the components as an assembly from pump
(2) .
9/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 19 g00620031
30. Remove bolts (49). Remove plates (48) and (50) .
31. If necessary, remove stops (52) from swashplate (51) .
Illustration 20 g00620032
32. Remove pistons (47) from plate (53) .
Illustration 21 g00620033
10/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 33. Remove bearing cone (54) .
Illustration 22 g00620036
34. Remove bearing cup (56) .
35. Remove bolts (58) and swashplate bearings (55) and (57) .
Illustration 23 g00620037
36. Use Tool (B) and remove two lip seals (59) from the housing. Note the direction of the lip
seals for assembly.
37. Use Tooling (A) and remove two snap rings (60) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:19:38 UTC+0800 2019
11/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014262
Implement Pump - Assemble
SMCS - 5084-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 1P-1858 Pliers 1
B 1P-0510 Driver Group 1
1. Clean all of the parts and inspect all of the parts. If parts are damaged or worn, install new
parts. Put clean oil on all of the internal parts of the pump.
Note: Replace all O-ring seals, gaskets, and shaft seals.
Illustration 1 g00620037
1/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Use Tool (A) to install two snap rings (60) .
3. Use Tool (B) to install two lip seals (59) in the housing.
Illustration 2 g00620036
4. Use bolts (58) to install swashplate bearings (55) and (57). Tighten bolts (58) to a torque of
4 ± .4 N·m (35 ± 3.5 lb in).
5. Install bearing cup (56) .
Illustration 3 g00620033
6. Install bearing cone (54) .
2/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
Note: Use the following procedure to assemble the components of barrel (40) .
9. Put guide (41), spring (44), and guide (42) in position in barrel (40) .
10. Use a press to compress spring (44). Use Tool (A) to install snap ring (43) .
11. Be sure that snap ring (43) is properly seated. Slowly release the compression on spring
(44) .
Illustration 7 g00620032
Illustration 8 g00620965
4/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 12. Install pistons (47) on plate (53). Install the pistons in barrel (40) .
Illustration 9 g00620969
13. Install assembled barrel (40), the plate, and the pistons on the shaft as a unit. Be sure that
the splines are aligned.
Illustration 10 g00620975
14. Apply 9S-3263 Thread Lock Compound to the threads of bolts (49). Install plates (48) and
(50) with the bolts. Tighten the bolts to a torque of 14 ± 1 N·m (124 ± 9 lb in).
5/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 11 g00619963
15. Install spacer (39) to the shaft.
Illustration 12 g00619962
16. Install plug (38) and the O-ring seal in pump (2). Tighten the plug to a torque of 101.5 ± 4.5
N·m (75 ± 3 lb ft).
17. Install bearing cone (37) on the shaft.
6/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 13 g00619959
18. Install the O-ring seal, cover (36), and bolts (35). Tighten the bolts to a torque of 8.5 ± 1
N·m (75 ± 9 lb in).
Note: If the shaft bearings, the shaft, the head, or the housing were replaced, an end play
adjustment must be made. To obtain axial shaft end play of .01 to .10 mm (.0004 to .0039
inch), use the required shims from the 9T-3038 Shaft Shim Kit .
19. Install gasket (34) on pump (2) .
Illustration 14 g00619958
20. Install the O-ring seals on pistons (30) and (31). Apply Loctite No. 680 sealant to the
threads of the pistons.
21. Install the pistons in head (24) and tighten to a torque of 79 ± 4 N·m (58 ± 3 lb ft).
22. If pin (33) was removed, install the pin.
23. Install bearing cup (32) .
Illustration 15 g00619956
7/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 24. Install plate (29). Be sure that the notch in the plate is aligned with pin (33) .
Illustration 16 g00619954
25. Install the spacer under cylinder (26) and install cylinder (26) in head (24) .
26. Install cylinder (27) and spring (28) .
Illustration 17 g00619953
27. Use bolts (25) to install head (24) to pump (2). Tighten the bolts evenly to a torque of 71 ±
14 N·m (52 ± 10 lb ft).
8/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 18 g00619952
28. Install O-ring seals (23) on the compensator.
29. Install the O-ring seal and plug (17) on the compensator. Tighten the plug to a torque of
30.5 ± 1.5 N·m (23 ± 1 lb ft).
30. Install screw (22) in compensator plug (21) .
31. Install guide (18), spring (19), guide (20), and compensator plug (21) in the compensator.
Illustration 19 g00619950
32. Install screw (16) in margin plug (15) .
33. Install guide (11), spring (12), spring stop pin (13), guide (14), and margin plug (15) in
compensator (3) .
9/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 20 g00619949
34. Tighten locknuts (9) and (10) to a torque of 17 ± 3 N·m (150 ± 26 lb in).
Note: Refer to Systems Operation, Testing and Adjusting, SENR9424 for the correct
procedure for adjusting the flow compensator.
Illustration 21 g00619947
35. Put spools (5) and (7) in position in the compensator.
36. Install plugs (6) and (8). Tighten the plugs to a torque of 30.5 ± 1.5 N·m (22 ± 1 lb ft).
10/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 22 g00619942
37. Use bolts (4) to install compensator (3) on the pump. Tighten the bolts to a torque of 34 ± 3
N·m (25 ± 2 lb ft).
Illustration 23 g00619940
38. Install O-ring seal (1) on pump (2) .
End By: Install the implement pump.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:20:27 UTC+0800 2019
11/11
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEB...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014258
Implement Pump - Install
SMCS - 5084-012
Installation Procedure
Illustration 1 g00619647
1. Be sure that the O-ring seal is in position on the front of the pump.
2. The approximate weight of the implement pump is 33 kg (73 lb). Use a floor jack to put the
implement pump in position.
3. Install the washers and four nuts (7) .
1/2
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g00619642
4. Connect hose assemblies (3), (4), (5), and (6) to the implement pump.
Illustration 3 g00619640
5. The weight of the rear bottom guard is 70 kg (155 lb). Use bolts (1) and the washers to
install rear bottom guard (2) .
6. Fill the hydraulic tank to the correct level.
Note: For the correct procedure to fill the hydraulic system on the 527 Track-Type Skidder, refer
to Operation and Maintenance Manual, SEBU7001, "Hydraulic System Oil - Change".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 21 18:21:16 UTC+0800 2019
2/2
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
30. Shutdown SIS
Previous Screen
Product: TRACK SKIDDER
Model: 527 TRACK SKIDDER PTR
Configuration: 527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine
Disassembly and Assembly
527 Track-Type Skidder Machine Supplements
Media Number -SENR9426-04 Publication Date -01/11/2009 Date Updated -03/11/2009
i01014266
Bulldozer Control Valve - Remove
SMCS - 5115-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
1/8
527 Track Skidder PTR00001-UP (MACHINE) POWERED BY 3304 Engine(SEBP5...
2019/9/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...