What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 450F BACKHOE LOADER HJR
Configuration: 450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR0602-11 Publication Date -01/08/2013 Date Updated -25/10/2017
i04047746
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Front
Pulley- Remove and Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02443718
1. Install the legs of Tooling (A) behind crankshaft front seal (2). Install a suitable spacer
between Tooling (A) and the crankshaft.
2. Use Tooling (A) in order to pull crankshaft front seal (2) out of front cover (1).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Front Seal Installer 1
9U-6207 Plate 1
9U-6208 Anchor Plate 1
276-1209 Seal Installer Tool 1
9U-6209 Sleeve 1
2/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g02443719
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Front Pulley-
Remove and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:18:33 UTC+0800 2019
4/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 450F BACKHOE LOADER HJR
Configuration: 450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR0602-11 Publication Date -01/08/2013 Date Updated -25/10/2017
i05016731
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & installer Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Front
Pulley- Remove and Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g02445196
1. Align Tooling (A) onto crankshaft front seal (2).
2. Turn Tooling (A) in a counterclockwise direction and remove crankshaft front seal (2) from
front cover (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 367-3534 Oil Seal Removal & installer Tool 1
B - Loctite 5900 -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 1. Ensure that the front cover is clean and free from damage.
Illustration 2 g02445217
3/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g02445197
2. Apply a continuous bead of Tooling (B), approximately 3 mm (0.118 inch) in diameter, to
the top of the static seal beads (3).
3. Correctly position a new crankshaft front seal (2) in Position (X) onto front cover (1).
4. Position Tooling (A) onto crankshaft front seal (2).
5. Use Tooling (A) in order to turn crankshaft front seal (2) in clockwise direction.
6. If it is necessary, to apply a torque greater than 50 N·m (37 lb ft) in order to install
crankshaft front seal (2). Remove crankshaft front seal (2). Inspect the crankshaft front seal
and the front cover for faults or damage.
7. If necessary repeat Step 2 through Step 6 in order to install crankshaft front seal (2).
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Front Pulley-
Remove and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:19:32 UTC+0800 2019
4/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 450F BACKHOE LOADER HJR
Configuration: 450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR0602-11 Publication Date -01/08/2013 Date Updated -25/10/2017
i04047877
Front Cover - Remove and Install - Heavy Duty Front Cover
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install" for the correct procedure.
b. If the engine has a fan, remove the fan. Refer to Disassembly and Assembly, "Fan - Remove
and Install" for the correct procedure.
1/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g02480997
1. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
2. Remove bolts (3) and bolts (4). Identify the positions of bolts of different length.
3. Remove front cover (1) from front housing (5).
4. Remove gasket (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 by 70 mm
2
B 364-7209 Front Cover Alignment Tool 1
2/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g02480998
1. Ensure that all components are clean and free from damage. Replace any damaged
components.
2. Thoroughly clean the gasket surface of front housing (5).
3. Thoroughly clean front cover (1).
4. Install Tooling (A) into Holes (X) in front housing (5).
5. Install a new gasket (2) onto Tooling (A).
6. Install front cover (1) onto Tooling (A).
7. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
8. Use Tooling (B) to align the front cover assembly.
3/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 9. Remove Tooling (A) and install the remaining bolts.
10. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
11. Remove Tooling (B).
12. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install" for the correct procedure.
b. If the engine has a fan, install the fan. Refer to Disassembly and Assembly, "Fan - Remove
and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:20:31 UTC+0800 2019
4/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 450F BACKHOE LOADER HJR
Configuration: 450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR0602-11 Publication Date -01/08/2013 Date Updated -25/10/2017
i04047880
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install" for the correct procedure.
b. If the engine has a fan, remove the fan. Refer to Disassembly and Assembly, "Fan - Remove
and Install" for the correct procedure.
1/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g02481028
1. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
2. Remove bolts (3) and bolts (4). Identify the positions of bolts of different length.
3. Remove front cover (1) from front housing (5).
4. Remove gasket (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 by 70 mm
2
B 342-9206 Front Cover Alignment Tool 1
2/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g02481030
1. Thoroughly clean the gasket surface of the front housing.
2. If the original front cover is installed, follow Step 2.a through Step 2.b.
a. Thoroughly clean front cover (1).
b. Install a new gasket (2) to front cover (1). Engage Locators (Y) into the holes in the
front cover.
3. Install Tooling (A) into Holes (X) in front housing (5).
4. Use Tooling (A) in order to position the front cover assembly onto the front housing.
5. Install bolts (3) and bolts (4) finger tight. Ensure that the bolts of different length are
installed in the correct positions.
3/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 6. Install a new front seal to the front cover. Refer to Disassembly and Assembly, "Crankshaft
Front Seal - Remove and Install" for the correct procedure.
7. Use Tooling (B) in order to align the front cover.
8. Remove Tooling (A) and install the remaining bolts.
9. Tighten bolts (3) and bolts (4) to a torque of 22 N·m (195 lb in).
10. Remove Tooling (B) from the front cover.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install" for the correct procedure.
b. If the engine has a fan, install the fan. Refer to Disassembly and Assembly, "Fan - Remove
and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 9 23:21:31 UTC+0800 2019
4/4450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 450F BACKHOE LOADER HJR
Configuration: 450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR0602-11 Publication Date -01/08/2013 Date Updated -25/10/2017
i04048571
Gear Group (Front) - Remove and Install - Heavy Duty Gear
Group (Front)
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107
Timing Pin
(Fuel Injection Pump)
1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40Torx Socket 1
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
NOTICE
1/20450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the front gear group. Carefully follow the procedure in order to remove the gear
group.
1. If the air compressor is equipped with a hydraulic pump, remove the hydraulic pump. Refer
to Original Equipment Manufactures (OEM) for the correct procedure.
2. If the engine is equipped with an air compressor, remove the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Remove" for the correct procedure.
3. If the engine is equipped with only a hydraulic pump, remove the hydraulic pump. Refer to
OEM for the correct procedure.
4. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
2/20450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g02486477
5. Remove plug (1) from the cylinder block. Remove O-ring seal (2) from the plug.
6. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke.
7. Remove Tooling (D).
8. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
3/20450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g02048655
9. Use Tooling (E) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew
threaded inserts (4) on all rocker arms (3) until all valves are fully closed. Ensure that the
guides (5) for the pushrods are left in position on the threaded inserts (4).
Note: Ensure that ALL threaded inserts are fully unscrewed.
10. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to Illustration 1.
4/20450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g02488136
11. Install Tooling (B) through Hole (X) in camshaft gear (6) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation,
Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct
procedure.
12. Use Tooling (C) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
5/20450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 4 g02052394
13. If the right-hand side of the engine is equipped with a hydraulic pump, remove the hydraulic
pump. Refer to OEM for the correct procedure.
14. If necessary, remove bolts (7) from plate (8). Remove plate (8) and remove O-ring seal (9).
15. Remove circlip (10) and remove gear assembly (11) from front housing (12).
6/20450F Backhoe Loader HJR00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/12/9https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...