The document provides instructions for installing an idler gear on a Caterpillar C4.4 engine. It describes cleaning and inspecting parts, aligning timing marks, installing various components like the idler gear, hub, and plate, and torquing bolts. It also provides instructions for checking end play and backlash and lubricating gears once installation is complete.
Caterpillar cat 444 e backhoe loader (prefix nba) service repair manual (nba0...fjsjejfksekmme
The document provides instructions for installing the front housing on a Caterpillar C4.4 engine. It outlines the required tools and parts. The procedure involves installing the thrust washer, aligning the front housing with guide bolts and an alignment tool, and securing it with bolts. Final steps include installing the idler gear plate if applicable, and lubricating the gears.
Caterpillar cat 444 f backhoe loader (prefix ljj) service repair manual (ljj0...fjsjjfkskeme
The document provides instructions for installing the front housing on a C4.4 engine. It lists the required tools which include sealant and bolts. The steps include cleaning and inspecting the front housing, installing blanking plugs if needed, checking the crankshaft seal, cleaning the cylinder block mating surfaces, installing the thrust washer and joint, aligning the housing dowels and installing bolts to secure the housing. Tightening specifications and installing remaining components like the bypass tube and idler gear plate are also outlined.
Caterpillar cat m314 f wheeled excavator (prefix f4a) service repair manual (...ufjjskekkmed
The document provides instructions for removing the front housing on a C4.4 engine. Key steps include:
1. Removing various external components like the fan, pulley, oil pan, and gears.
2. Disconnecting electrical and coolant components from the front housing.
3. Removing several bolts of different lengths that secure the front housing to the engine block.
4. Removing the front housing and gasket from the engine block. Proper identification of removed parts is important for reinstallation.
Caterpillar cat 430 f backhoe loader (prefix lnh) service repair manual (lnh0...fjjskekskemmm
This document provides instructions for removing and installing the front gear group of a Caterpillar C4.4 engine. It describes:
1) Using turning tools to lock the crankshaft and camshaft in position before removal to maintain timing.
2) Loosening rocker arms, unscrewing adjusters, and locking the fuel injection pump to remove tension from gears.
3) Marking gears to ensure proper reinstallation alignment.
4) Removing the camshaft, idler, and fuel pump gears, cleaning components, and checking for wear.
5) Reinstalling gears using timing pins to set alignment, measuring backlash, and adjusting valves before reassembly.
Caterpillar cat 420 f backhoe loader (prefix ltg) service repair manual (ltg0...ufjjsjekkmdme
This document provides instructions for removing and installing the front gear group of a Caterpillar C4.4 engine. It describes:
1) Required tools including a crankshaft turning tool, timing pins, and indicator tools.
2) Removal procedures which include locking the crankshaft and camshaft positions, loosening rocker arms, and removing gears in a specific order while maintaining timing marks for alignment.
3) Installation procedures which include cleaning and inspecting components, installing gears in reverse order while aligning timing marks and measuring backlash, and adjusting valves at the end.
Caterpillar cat 120 h motor grader (prefix 5fm) service repair manual (5fm000...fusefjjskekemm
- The document provides instructions for removing and installing the camshaft on a 120H Motor Grader with a 3116 engine. It describes removing components like the governor and covers, then turning the crankshaft to align marks before removing the camshaft, gear, and bearings. Installation is the reverse of removal.
- Instructions are given to remove and install the camshaft gear by pressing it off the camshaft and heating it to 315°C before reinstalling.
- The procedure to remove and install camshaft bearings uses a special tool and orients the oil holes during installation.
Caterpillar cat 321 c excavator (prefix kbb) service repair manual (kbb00001 ...ufjjskekkmde
This document provides instructions for removing and disassembling the water pump from a Caterpillar 321C excavator engine. It describes draining the coolant, removing four bolts to detach the water pump pulley and pump as a unit from the engine, and removing the O-ring from the pump. The disassembly section then details removing the four bolts securing the pulley to the pump body and separating the two components after heating the pump to 80°C to ease removal.
This document provides instructions for removing and installing piston rings and connecting rod bearings on a Caterpillar 3306 engine. It describes the required tools and steps to disassemble pistons and connecting rods, including removing piston rings, piston pins, and bearings. It then explains how to assemble pistons and connecting rods, including cleaning parts, installing bearings, rings, piston pins, and connecting rods. Finally, it describes installing the pistons and connecting rods back into the engine.
Caterpillar cat 444 e backhoe loader (prefix nba) service repair manual (nba0...fjsjejfksekmme
The document provides instructions for installing the front housing on a Caterpillar C4.4 engine. It outlines the required tools and parts. The procedure involves installing the thrust washer, aligning the front housing with guide bolts and an alignment tool, and securing it with bolts. Final steps include installing the idler gear plate if applicable, and lubricating the gears.
Caterpillar cat 444 f backhoe loader (prefix ljj) service repair manual (ljj0...fjsjjfkskeme
The document provides instructions for installing the front housing on a C4.4 engine. It lists the required tools which include sealant and bolts. The steps include cleaning and inspecting the front housing, installing blanking plugs if needed, checking the crankshaft seal, cleaning the cylinder block mating surfaces, installing the thrust washer and joint, aligning the housing dowels and installing bolts to secure the housing. Tightening specifications and installing remaining components like the bypass tube and idler gear plate are also outlined.
Caterpillar cat m314 f wheeled excavator (prefix f4a) service repair manual (...ufjjskekkmed
The document provides instructions for removing the front housing on a C4.4 engine. Key steps include:
1. Removing various external components like the fan, pulley, oil pan, and gears.
2. Disconnecting electrical and coolant components from the front housing.
3. Removing several bolts of different lengths that secure the front housing to the engine block.
4. Removing the front housing and gasket from the engine block. Proper identification of removed parts is important for reinstallation.
Caterpillar cat 430 f backhoe loader (prefix lnh) service repair manual (lnh0...fjjskekskemmm
This document provides instructions for removing and installing the front gear group of a Caterpillar C4.4 engine. It describes:
1) Using turning tools to lock the crankshaft and camshaft in position before removal to maintain timing.
2) Loosening rocker arms, unscrewing adjusters, and locking the fuel injection pump to remove tension from gears.
3) Marking gears to ensure proper reinstallation alignment.
4) Removing the camshaft, idler, and fuel pump gears, cleaning components, and checking for wear.
5) Reinstalling gears using timing pins to set alignment, measuring backlash, and adjusting valves before reassembly.
Caterpillar cat 420 f backhoe loader (prefix ltg) service repair manual (ltg0...ufjjsjekkmdme
This document provides instructions for removing and installing the front gear group of a Caterpillar C4.4 engine. It describes:
1) Required tools including a crankshaft turning tool, timing pins, and indicator tools.
2) Removal procedures which include locking the crankshaft and camshaft positions, loosening rocker arms, and removing gears in a specific order while maintaining timing marks for alignment.
3) Installation procedures which include cleaning and inspecting components, installing gears in reverse order while aligning timing marks and measuring backlash, and adjusting valves at the end.
Caterpillar cat 120 h motor grader (prefix 5fm) service repair manual (5fm000...fusefjjskekemm
- The document provides instructions for removing and installing the camshaft on a 120H Motor Grader with a 3116 engine. It describes removing components like the governor and covers, then turning the crankshaft to align marks before removing the camshaft, gear, and bearings. Installation is the reverse of removal.
- Instructions are given to remove and install the camshaft gear by pressing it off the camshaft and heating it to 315°C before reinstalling.
- The procedure to remove and install camshaft bearings uses a special tool and orients the oil holes during installation.
Caterpillar cat 321 c excavator (prefix kbb) service repair manual (kbb00001 ...ufjjskekkmde
This document provides instructions for removing and disassembling the water pump from a Caterpillar 321C excavator engine. It describes draining the coolant, removing four bolts to detach the water pump pulley and pump as a unit from the engine, and removing the O-ring from the pump. The disassembly section then details removing the four bolts securing the pulley to the pump body and separating the two components after heating the pump to 80°C to ease removal.
This document provides instructions for removing and installing piston rings and connecting rod bearings on a Caterpillar 3306 engine. It describes the required tools and steps to disassemble pistons and connecting rods, including removing piston rings, piston pins, and bearings. It then explains how to assemble pistons and connecting rods, including cleaning parts, installing bearings, rings, piston pins, and connecting rods. Finally, it describes installing the pistons and connecting rods back into the engine.
New holland lm1745 turbo telescopic handler parts catalogue manualfjjkskekfsmem
This document is a parts catalog for New Holland tractor models LM1340 TURBO through LM1745 TURBO. It contains listings of engine, crankcase, oil sump, and crankcase cover parts, organized by model and part number. Parts are identified by name in multiple languages along with part numbers, specifications, and quantities required. The catalog contains technical drawings and exploded views of engine assemblies. Copyright information is provided on each page.
New holland e22.2 sr mini crawler excavator parts catalogue manualfjjkskekfsmem
This document is a parts catalog containing listings of parts for various models including E20.2SR and E22.2SR. The sections provide part numbers, descriptions, and quantities for individual components. Section 013-60 lists parts for a bracket assembly for a swing arm used on nibblers and breakers, including pivots, bushings, clamps, screws, washers and other hardware.
Kubota wg972 e2 natural gas engine service repair manualfjjkskekfsmem
This document provides specifications for the WG972-E2, DF972-E2, and DG972-E2 engines. It lists details such as the engine type, displacement, power output, speed, lubrication system, cooling system, and fuel for each model. The DF972-E2 is a dual fuel engine that can operate on either gasoline or LPG, while the DG972-E2 operates on natural gas.
Kioti daedong rx6010 c tractor operator manualfjjkskekfsmem
This document provides an owner's manual for a KIOTI RX6010C/RX6010PC tractor. It begins by welcoming the new owner and providing some background on the tractor's design and quality standards. The manual aims to help owners safely and properly operate the tractor through information on safety precautions, specifications, operating systems, and maintenance. Safety is emphasized, with sections covering precautions for starting, driving, parking, using attachments, and servicing the tractor, as well as safety decals.
Kioti daedong ex50 ch tractor parts catalogue manualfjjkskekfsmem
The cylinder block group document provides labor hours for servicing parts of the cylinder block assembly. It lists 24 job codes ranging from complete engine replacement to individual parts like plugs, seals, pins, and the oil pump assembly. Instructions are provided on only using relevant job codes to avoid rejection of warranty claims.
This document provides an owner's manual for a KIOTI DK 751/901 tractor. It begins by congratulating the owner on their purchase and explaining that the tractor was designed and manufactured to high quality standards. It emphasizes the importance of reading and understanding the entire manual before operating the tractor. The manual then provides sections on safety precautions, operating instructions, maintenance, and troubleshooting. It includes diagrams and descriptions of controls, specifications for the tractor models, and lists of safety labels and their meanings.
Kioti daedong dk551 c tractor parts catalogue manualfjjkskekfsmem
This document provides instructions and information for a tractor parts list, including:
1. It lists 10 items that provide information about how the parts list is organized and how to use it.
2. It provides a table of contents that lists the component groups included in the parts list.
3. It indicates that the parts list is subject to change without notice due to continuous product improvements.
The document provides an overview of safety precautions for operating a KIOTI DK451/501/551 tractor. Key points include:
- Read the entire owner's manual before operating the tractor. Only properly trained persons should operate it.
- Replace any missing or damaged safety decals and keep decals clean.
- Do not operate the tractor under the influence of drugs or alcohol or while fatigued. Communicate intentions when working with other tractors.
- Never start the engine from the ground and only have the operator ride the tractor unless a passenger seat is installed.
- Use the seat belt if the tractor has a ROPS and cabin installed and never use the seat belt
Kioti daedong dk450 l tractor parts catalogue manualfjjkskekfsmem
This document is a spare parts list for DK 35-40-450L tractors. It provides information on part groups, components, references, interchangeability, and specifications for different models. The list contains headings for part number, name, remarks, identification code and quantity. It then shows the parts included for the cylinder block group and cylinder head group, listing each part and providing the corresponding information for various tractor models.
Case cx50 b mini crawler excavator parts catalogue manualfjjkskekfsmem
This document provides a parts catalogue for a CX50B mini crawler excavator. It lists various maintenance, engine installation, air cleaner, muffler, and radiator parts. The parts are organized by section and include the part number, quantity, and description. Reference numbers are provided to link to additional details for some parts.
Case cx31 b mini crawler excavator parts catalogue manualfjjkskekfsmem
The document is a parts catalogue for a CX31B mini crawler excavator that lists replacement parts by section and part number. It includes sections for the engine, air cleaner, muffler, radiator installation, and radiator components. Each section lists the relevant part numbers, quantities, and part descriptions.
Case 1850 k tier 2 crawler dozer parts catalogue manualfjjkskekfsmem
This document provides a parts catalogue for a 1850K Crawler Dozer from 2003 with a Tier 2 engine. It lists various engine parts in the crankcase, oil sump, crankcase covers, and breather. Specific part numbers, quantities, and descriptions are provided for each component.
Hyster h45 xm (h177) forklift service repair manualfjjkskekfsmem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Bobcat utility blade, angle dozer, mini and super, scraper, attachment, contr...fjjkskekfsmem
This document contains a parts list for a chipper machine. It lists 55 parts in the first section with descriptions and part numbers. The second section lists another 68 parts for the chipper. Notes at the bottom provide additional information about translation kits and manuals. The parts list provides specifications for replacement and repair of components for the chipper.
Hyster f187 (s2.0 ft europe) forklift service repair manualfjjkskekfsmem
The document provides instructions for servicing and repairing a lift truck. It warns that the lift truck must be stabilized with blocks when removing parts that change the center of gravity, such as the mast, drive axle, engine, and counterweight. It then details how to remove and replace parts like the hood, seat, side covers, and floor plate to access other components for maintenance and repair. Diagrams show the frame and locations of parts.
Bobcat brooms sweepers, graders, water kits attachments parts catalogue manualfjjkskekfsmem
This document provides a list of parts for an angle broom. It includes 42 line items describing individual parts like the frame, legs, wheels, motor, and various hardware. It also includes summaries of additional documents that provide details on related parts like the hydraulic cylinder, caster wheel, and hydraulic motor.
Bobcat 873 g series skid steer loader parts catalogue manual (sn 517911001 &a...fjjkskekfsmem
This document provides a parts list for a main frame assembly. It lists 31 part numbers, descriptions, remarks and quantities. A second page continues the parts list for an operator cab assembly, listing 32 additional parts. The third page is a parts list for a seat and seat bar assembly with 24 parts. Further pages continue listing additional assemblies.
Bobcat 873 f series skid steer loader parts catalogue manual (sn 5142 11001 ...fjjkskekfsmem
The document provides a parts list for various components of an excavator. It includes over 40 line items specifying part numbers, descriptions, serial numbers (when applicable) and quantities of items such as frames, bushings, nuts, bolts, shields, seals and other miscellaneous parts. The parts are grouped into sections including the main frame, operator cab, seat, and seat bar.
Bobcat 853 skid steer loader parts catalogue manual (sn 512816001 & above )fjjkskekfsmem
This document contains parts lists and descriptions for various components of a machine. It includes sections for the main frame, operator cab, seat and seat bar, and seat. It lists over 50 individual part numbers, descriptions, quantities, and other details for each section. The parts listed are for structural, insulating, and protective components of the machine's frame, cab, and operator seating area.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
New holland lm1745 turbo telescopic handler parts catalogue manualfjjkskekfsmem
This document is a parts catalog for New Holland tractor models LM1340 TURBO through LM1745 TURBO. It contains listings of engine, crankcase, oil sump, and crankcase cover parts, organized by model and part number. Parts are identified by name in multiple languages along with part numbers, specifications, and quantities required. The catalog contains technical drawings and exploded views of engine assemblies. Copyright information is provided on each page.
New holland e22.2 sr mini crawler excavator parts catalogue manualfjjkskekfsmem
This document is a parts catalog containing listings of parts for various models including E20.2SR and E22.2SR. The sections provide part numbers, descriptions, and quantities for individual components. Section 013-60 lists parts for a bracket assembly for a swing arm used on nibblers and breakers, including pivots, bushings, clamps, screws, washers and other hardware.
Kubota wg972 e2 natural gas engine service repair manualfjjkskekfsmem
This document provides specifications for the WG972-E2, DF972-E2, and DG972-E2 engines. It lists details such as the engine type, displacement, power output, speed, lubrication system, cooling system, and fuel for each model. The DF972-E2 is a dual fuel engine that can operate on either gasoline or LPG, while the DG972-E2 operates on natural gas.
Kioti daedong rx6010 c tractor operator manualfjjkskekfsmem
This document provides an owner's manual for a KIOTI RX6010C/RX6010PC tractor. It begins by welcoming the new owner and providing some background on the tractor's design and quality standards. The manual aims to help owners safely and properly operate the tractor through information on safety precautions, specifications, operating systems, and maintenance. Safety is emphasized, with sections covering precautions for starting, driving, parking, using attachments, and servicing the tractor, as well as safety decals.
Kioti daedong ex50 ch tractor parts catalogue manualfjjkskekfsmem
The cylinder block group document provides labor hours for servicing parts of the cylinder block assembly. It lists 24 job codes ranging from complete engine replacement to individual parts like plugs, seals, pins, and the oil pump assembly. Instructions are provided on only using relevant job codes to avoid rejection of warranty claims.
This document provides an owner's manual for a KIOTI DK 751/901 tractor. It begins by congratulating the owner on their purchase and explaining that the tractor was designed and manufactured to high quality standards. It emphasizes the importance of reading and understanding the entire manual before operating the tractor. The manual then provides sections on safety precautions, operating instructions, maintenance, and troubleshooting. It includes diagrams and descriptions of controls, specifications for the tractor models, and lists of safety labels and their meanings.
Kioti daedong dk551 c tractor parts catalogue manualfjjkskekfsmem
This document provides instructions and information for a tractor parts list, including:
1. It lists 10 items that provide information about how the parts list is organized and how to use it.
2. It provides a table of contents that lists the component groups included in the parts list.
3. It indicates that the parts list is subject to change without notice due to continuous product improvements.
The document provides an overview of safety precautions for operating a KIOTI DK451/501/551 tractor. Key points include:
- Read the entire owner's manual before operating the tractor. Only properly trained persons should operate it.
- Replace any missing or damaged safety decals and keep decals clean.
- Do not operate the tractor under the influence of drugs or alcohol or while fatigued. Communicate intentions when working with other tractors.
- Never start the engine from the ground and only have the operator ride the tractor unless a passenger seat is installed.
- Use the seat belt if the tractor has a ROPS and cabin installed and never use the seat belt
Kioti daedong dk450 l tractor parts catalogue manualfjjkskekfsmem
This document is a spare parts list for DK 35-40-450L tractors. It provides information on part groups, components, references, interchangeability, and specifications for different models. The list contains headings for part number, name, remarks, identification code and quantity. It then shows the parts included for the cylinder block group and cylinder head group, listing each part and providing the corresponding information for various tractor models.
Case cx50 b mini crawler excavator parts catalogue manualfjjkskekfsmem
This document provides a parts catalogue for a CX50B mini crawler excavator. It lists various maintenance, engine installation, air cleaner, muffler, and radiator parts. The parts are organized by section and include the part number, quantity, and description. Reference numbers are provided to link to additional details for some parts.
Case cx31 b mini crawler excavator parts catalogue manualfjjkskekfsmem
The document is a parts catalogue for a CX31B mini crawler excavator that lists replacement parts by section and part number. It includes sections for the engine, air cleaner, muffler, radiator installation, and radiator components. Each section lists the relevant part numbers, quantities, and part descriptions.
Case 1850 k tier 2 crawler dozer parts catalogue manualfjjkskekfsmem
This document provides a parts catalogue for a 1850K Crawler Dozer from 2003 with a Tier 2 engine. It lists various engine parts in the crankcase, oil sump, crankcase covers, and breather. Specific part numbers, quantities, and descriptions are provided for each component.
Hyster h45 xm (h177) forklift service repair manualfjjkskekfsmem
This document provides instructions for servicing and repairing various components of a lift truck, including the operator module, hood, overhead guard, counterweight, and LED backup lights. It describes removing and installing these parts, highlights important safety warnings, and notes specifications for tightening fasteners. Diagrams are included to illustrate the components and repair procedures.
Bobcat utility blade, angle dozer, mini and super, scraper, attachment, contr...fjjkskekfsmem
This document contains a parts list for a chipper machine. It lists 55 parts in the first section with descriptions and part numbers. The second section lists another 68 parts for the chipper. Notes at the bottom provide additional information about translation kits and manuals. The parts list provides specifications for replacement and repair of components for the chipper.
Hyster f187 (s2.0 ft europe) forklift service repair manualfjjkskekfsmem
The document provides instructions for servicing and repairing a lift truck. It warns that the lift truck must be stabilized with blocks when removing parts that change the center of gravity, such as the mast, drive axle, engine, and counterweight. It then details how to remove and replace parts like the hood, seat, side covers, and floor plate to access other components for maintenance and repair. Diagrams show the frame and locations of parts.
Bobcat brooms sweepers, graders, water kits attachments parts catalogue manualfjjkskekfsmem
This document provides a list of parts for an angle broom. It includes 42 line items describing individual parts like the frame, legs, wheels, motor, and various hardware. It also includes summaries of additional documents that provide details on related parts like the hydraulic cylinder, caster wheel, and hydraulic motor.
Bobcat 873 g series skid steer loader parts catalogue manual (sn 517911001 &a...fjjkskekfsmem
This document provides a parts list for a main frame assembly. It lists 31 part numbers, descriptions, remarks and quantities. A second page continues the parts list for an operator cab assembly, listing 32 additional parts. The third page is a parts list for a seat and seat bar assembly with 24 parts. Further pages continue listing additional assemblies.
Bobcat 873 f series skid steer loader parts catalogue manual (sn 5142 11001 ...fjjkskekfsmem
The document provides a parts list for various components of an excavator. It includes over 40 line items specifying part numbers, descriptions, serial numbers (when applicable) and quantities of items such as frames, bushings, nuts, bolts, shields, seals and other miscellaneous parts. The parts are grouped into sections including the main frame, operator cab, seat, and seat bar.
Bobcat 853 skid steer loader parts catalogue manual (sn 512816001 & above )fjjkskekfsmem
This document contains parts lists and descriptions for various components of a machine. It includes sections for the main frame, operator cab, seat and seat bar, and seat. It lists over 50 individual part numbers, descriptions, quantities, and other details for each section. The parts listed are for structural, insulating, and protective components of the machine's frame, cab, and operator seating area.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 444E BACKHOE LOADER NBA
Configuration: 444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763436
Idler Gear - Install
SMCS - 1206-012
Installation Procedure (Standard Idler Gear)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
C
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that number one piston is at the top center position on the compression stroke. Refer
to the Systems Operation, Testing and Adjusting, "Finding Top Center Postion for No. 1
Piston".
1/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01343975
Alignment of timing marks
2. Ensure that Tooling (A) is installed into hole (X) in camshaft gear (1).
3. Ensure that Tooling (B) is installed in hole (Y) in the front housing. Use Tooling (B) in
order to lock the crankshaft in the correct position. Refer to Systems Operation, Testing and
Adjusting, "Finding Top Centre Position for No.1 Piston".
Illustration 2 g01269934
4. Clean idler gear (2) and inspect the idler gear for wear or damage. Refer to Specifications,
"Gear Group (Front)" for more information. If necessary, replace the idler gear.
5. Clean hub (7) and inspect the hub for wear or damage. Refer to Specifications, "Gear Group
(Front)" for more information. If necessary, replace the hub.
2/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Lubricate hub (7) with clean engine oil. Slide the hub into idler gear (2). Ensure that the
timing marks are toward the front of the idler gear.
Illustration 3 g01269935
Typical example
7. Align the timing mark on idler gear (2) with the timing mark on the camshaft gear. Refer to
the Illustration 1. Install the assembly of idler gear (2) and hub (7) into the recess in the
timing case. Ensure that oil hole (Z) is to the top of the hub.
Note: The idler gear must be tilted during installation. Ensure that the holes in the hub are
aligned with the holes in the cylinder block.
8. Clean plate (3) and inspect the plate for wear or damage. If necessary, replace the plate.
9. Lubricate plate (3) with clean engine oil. A used plate should be installed in the original
orientation. If a new plate is installed, ensure that the holes in plate (3) are aligned with the
holes in hub (7). Install plate (3) to hub (7).
10. Install bolts (1). Tighten bolts (1) to a torque of 44 N�m (32 lb ft).
3/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g01269936
Checking end play by using a set of feeler gauge's
11. Use a set of feeler gauge's in order to check the end play for the idler gear. Refer to
Specifications, "Gear Group (Front)" for more information.
12. Use Tooling (C) in order to check the backlash between the idler gear and the camshaft
gear. Refer to Specifications, "Gear Group (Front)" for more information.
13. Use Tooling (C) in order to check the backlash between the idler gear and the crankshaft
gear. Refer to Specifications, "Gear Group (Front)" for more information.
14. Lightly lubricate all of the gears with clean engine oil.
End By:
a. Install the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear
- Install".
b. If the engine is equipped with an air compressor, install the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Remove and Install".
c. If the engine is equipped with a vacuum pump, install the vacuum pump. Refer to
Disassembly and Assembly, "Vacuum Pump - Remove and Install".
d. If the engine is equipped with an accessory drive, install the accessory drive. Refer to
Disassembly and Assembly, "Accessory Drive - Remove and Install".
Installation Procedure (Heavy-Duty Idler Gear)
Table 2
Required Tools
Tool Part Number Part Description Qty
4/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
C
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that number one piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Postion for No. 1
Piston".
Illustration 5 g01343977
Alignment of timing marks
2. Ensure that Tooling (A) is installed into hole (X) in the camshaft gear.
3. Ensure that Tooling (B) is installed in hole (Y) in the cylinder block. Use Tooling (B) in
order to lock the crankshaft in the correct position. Refer to Systems Operation, Testing and
Adjusting, "Finding Top Centre Position for No.1 Piston".
5/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 6 g01348946
Typical example
4. Install plate (6) into the recess in the front housing.
Note: Ensure that the identification mark TOP is upward.
5. Clean the assembly of idler gear (2) and inspect the assembly of the idler gear for wear or
damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary,
replace the assembly of the idler gear.
6. Lubricate the bearings in the assembly of idler gear (2) with clean engine oil.
6/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 7 g01269933
7. Align the timing mark on idler gear (2) with the timing mark on the camshaft gear. Refer to
Illustration 5. Install the assembly of idler gear (2) into the recess in the timing case. Ensure
that the identification mark TOP is upward.
Note: The idler gear must be tilted during installation. Ensure that the holes in the assembly
of the idler gear are aligned with the holes in the cylinder block.
8. Install bolts (1). Tighten bolts (1) to a torque of 44 N�m (32 lb ft).
Illustration 8 g01269937
Checking end play by using a dial indicator group
9. Use Tooling (C) in order to check the end play of the idler gear. Refer to Specifications,
"Gear Group (Front)" for more information.
7/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 10. Use Tooling (C) in order to check the backlash between the idler gear and the camshaft
gear. Refer to Specifications, "Gear Group (Front)" for more information.
11. Use Tooling (C) in order to check the backlash between the idler gear and the crankshaft
gear. Refer to Specifications, "Gear Group (Front)" for more information.
12. Lightly lubricate all of the gears with clean engine oil.
End By:
a. Install the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear
- Install".
b. If the engine is equipped with an air compressor, install the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Remove and Install".
c. If the engine is equipped with a vacuum pump, install the vacuum pump. Refer to
Disassembly and Assembly, "Vacuum Pump - Remove and Install".
d. If the engine is equipped with an accessory drive, install the accessory drive. Refer to
Disassembly and Assembly, "Accessory Drive - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 5 09:07:57 UTC+0800 2019
8/8444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 444E BACKHOE LOADER NBA
Configuration: 444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763440
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
b. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
e. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove and Install".
f. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/5444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the coolant is drained into a suitable container for storage or disposal. Refer to
Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct
procedure.
Illustration 1 g01337982
Typical example
2. Remove bolts (1) that secure bypass tube (2) to front housing (3). Note the position of any
brackets that are secured by the bolts. Remove bypass tube (2). Remove O-ring seals (4) and
(5) from bypass tube (2).
2/5444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 2 g01350333
3. If the engine is equipped with a heavy duty idle gear. Remove plate (6). Refer to
Disassembly and Assembly, "Idler Gear - Remove" for the correct procedure.
3/5444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g01350336
Typical example
4. Remove bolts (8), (9) and (10) from front housing (3).
Note: The bolts are three different lengths. Note the positions of the different bolts.
5. Remove front housing (3) from the cylinder block.
6. Remove joint (7).
4/5444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g01350337
Typical example
7. Remove thrust washer (11) from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 5 09:08:56 UTC+0800 2019
5/5444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 444E BACKHOE LOADER NBA
Configuration: 444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02843811
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6640 Sealant 1
B -
Guide Bolt
(M8 by 80 mm)
2
C
319-6486 Alignment Tool 1
-
Bolts
(M10 by 50 mm)
3
D - Straight Edge 1
E 1U-6396 O-Ring Assembly Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
1/7444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. If necessary, install blanking plugs to a new front housing. Use Tooling (A) to seal all D-
plugs.
2. Check the condition of the crankshaft front seal. If the front seal is damaged, remove the
front seal from the front housing.
3. Clean the mating surfaces of the cylinder block.
Illustration 1 g01350337
Typical example
4. Install thrust washer (11) into the recess in the cylinder block. Refer to Disassembly and
Assembly, "Camshaft - Install" for more information.
2/7444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g01350343
Typical example
5. Install Tooling (B) to the cylinder block. Refer to Illustration 2.
6. Install Tooling (C) to the cylinder block.
7. Align a new joint (7) with Tooling (B). Install the joint to the cylinder block.
Note: Ensure that tabs (X) on the joint are engaged in holes (Y) in the cylinder block.
3/7444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 3 g01269947
Typical example
8. Install the front housing over Tooling (B) and over Tooling (C) onto the cylinder block.
Illustration 4 g01350344
4/7444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. (8) M8 by 20 mm
(9) M8 by 35 mm
(10) M8 by 25 mm
9. Install bolts (10) to front housing (3) finger tight.
10. Remove Tooling (B).
11. Loosely install bolts (8) and (9). Refer to Illustration 4 for the correct position of the bolts.
12. Align the bottom face of front housing (3) to the lower machined face of the cylinder block.
Use a Tooling (D) and a feeler gauge in order to check the alignment between the front
housing and the cylinder block. Refer to Illustration 3. Refer to Specifications, "Front
Housing and Covers" for further information.
Illustration 5 g01269949
Tightening sequence for the front housing
13. Tighten bolts (8), (9) and (10) to a torque of 28 N�m (20 lb ft). Tighten the bolts in the
sequence that is shown in Illustration 5.
Note: Ensure that the housing and the cylinder block are correctly aligned.
14. Remove Tooling (C) from the cylinder block.
15. If necessary, install a new crankshaft front seal. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install".
5/7444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 6 g01350333
16. If the engine is equipped with a heavy duty idle gear. Install plate (6). Refer to Disassembly
and Assembly, "Idler Gear - Install" for the correct procedure.
Illustration 7 g01337982
Typical example
6/7444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 17. Install new O-ring seals (4) and (5) to bypass tube (2). Use Tooling (E) in order to lubricate
O-ring seal (5). Install bypass tube (2) to front housing (3). Install bolts (1). Ensure that any
brackets that are secured by the bolts are installed in the correct location. Tighten the bolts
to a torque of 22 N�m (16 lb ft).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install".
c. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
d. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
e. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Install".
f. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 5 09:09:56 UTC+0800 2019
7/7444E Backhoe Loader NBA00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...