This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It outlines the required tools and steps to remove the mounting bolts and lift the housing off the engine. For installation, it describes cleaning the mating surfaces, checking the oil pan seal and dowels, and lifting the housing into place before reinstalling the mounting bolts and torquing them to specification.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fusjejedrfjskekem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts and washers, lifting the flywheel off, and installing in reverse order. For the crankshaft rear seal, it differentiates between engines using a 14 bolt or 10 bolt housing assembly and outlines cleaning, pressing or placing the seal, and torquing bolts.
Caterpillar cat 416 b backhoe loader (prefix 8zk) service repair manual (8zk0...fujsjefksekmm
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using special tools to remove the pulley by loosening bolts and removing a locking plate. When installing the new pulley, the instructions specify tightening the bolts to the specified torque and installing a new locking plate. The summary is intended only to convey the main steps and should not be used as a replacement for the full instructions.
Caterpillar cat 426 b backhoe loader (prefix 5yj) service repair manual (5yj0...fjjsefkskemmm
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 diesel engine. It describes two different housing assembly styles that require different procedures. For the 14-bolt housing, the instructions are to remove bolts and housing, inspect the gasket, clean parts, install the new seal and gasket using a press, and reinstall the housing and bolts. For the 10-bolt housing, the procedure is to clean surfaces, place the one-piece housing on the crankshaft until it contacts the block, install bolts using an alignment tool, and tighten bolts in sequence.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg1...fusjejedrfjskekem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including:
- Removing the crankshaft rear seal by first removing the flywheel and then removing the seal, gasket, and housing from the cylinder block.
- Installing the crankshaft rear seal by pressing the new seal into the housing and installing the housing onto the cylinder block while aligning the gasket.
- Removing the flywheel housing by first removing mounting bolts and then lifting the housing off the cylinder block dowels.
- Installing the flywheel housing by cleaning mating surfaces, positioning the housing on dowels, and installing mounting bolts.
-
Caterpillar cat 426 b backhoe loader (prefix 6kl) service repair manual (6kl0...fjjsefkskemmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Attaching lifting tools to the flywheel housing and removing mounting bolts to separate the housing from the engine block.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Positioning the flywheel housing on the engine block and installing mounting bolts to secure it.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...ujdfjkkskmem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters
- Camshaft and camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep components clean and properly support parts.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fusjejedrfjskekem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts and washers, lifting the flywheel off, and installing in reverse order. For the crankshaft rear seal, it differentiates between engines using a 14 bolt or 10 bolt housing assembly and outlines cleaning, pressing or placing the seal, and torquing bolts.
Caterpillar cat 416 b backhoe loader (prefix 8zk) service repair manual (8zk0...fujsjefksekmm
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using special tools to remove the pulley by loosening bolts and removing a locking plate. When installing the new pulley, the instructions specify tightening the bolts to the specified torque and installing a new locking plate. The summary is intended only to convey the main steps and should not be used as a replacement for the full instructions.
Caterpillar cat 426 b backhoe loader (prefix 5yj) service repair manual (5yj0...fjjsefkskemmm
This document provides instructions for removing and installing the crankshaft rear seal on a Caterpillar 3054 diesel engine. It describes two different housing assembly styles that require different procedures. For the 14-bolt housing, the instructions are to remove bolts and housing, inspect the gasket, clean parts, install the new seal and gasket using a press, and reinstall the housing and bolts. For the 10-bolt housing, the procedure is to clean surfaces, place the one-piece housing on the crankshaft until it contacts the block, install bolts using an alignment tool, and tighten bolts in sequence.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg1...fusjejedrfjskekem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including:
- Removing the crankshaft rear seal by first removing the flywheel and then removing the seal, gasket, and housing from the cylinder block.
- Installing the crankshaft rear seal by pressing the new seal into the housing and installing the housing onto the cylinder block while aligning the gasket.
- Removing the flywheel housing by first removing mounting bolts and then lifting the housing off the cylinder block dowels.
- Installing the flywheel housing by cleaning mating surfaces, positioning the housing on dowels, and installing mounting bolts.
-
Caterpillar cat 426 b backhoe loader (prefix 6kl) service repair manual (6kl0...fjjsefkskemmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Attaching lifting tools to the flywheel housing and removing mounting bolts to separate the housing from the engine block.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Positioning the flywheel housing on the engine block and installing mounting bolts to secure it.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...ujdfjkkskmem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters
- Camshaft and camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep components clean and properly support parts.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 428 b backhoe loader (prefix 7ej) service repair manual (7ej0...fujjdfjkksekmem
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. The removal procedure involves removing bolts to detach the front housing from the cylinder block and oil pan. Installation requires replacing the gasket, applying sealant, installing bolts in the correct sequence, and ensuring proper alignment. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...ujfjjsjekkmsmd
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 436 c backhoe loader (prefix 2ar) service repair manual (2ar0...fusjejfskekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels using lifting brackets, and installing mounting bolts. Tools required include lifting brackets and bolts of the appropriate size.
Caterpillar cat 416 c backhoe loader (prefix 5yn) service repair manual (5yn0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 416C backhoe loader engine. It describes using lifting brackets and bolts to remove the housing. For installation, it instructs to clean mating surfaces, position the housing on dowels, and install bolts while supporting the housing with lifting brackets. Torque specifications are provided for tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 420 d backhoe loader (prefix bmc) service repair manual (bmc0...ujfjjskkemm
The document provides instructions for removing and installing a front tie rod on a 420D backhoe loader. It lists the required tools which include a transmission repair stand. The removal process first requires removing the front axle from the machine. Safety precautions are provided to release hydraulic pressure and ensure cool oil before removing any hydraulic components or lines.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Installing the housing by positioning it on the cylinder block and installing mounting bolts, taking care to keep parts clean of contaminants.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Installing the housing by positioning it on the cylinder block and installing mounting bolts, taking care to keep parts clean of contaminants.
Caterpillar cat 426 b backhoe loader (prefix 5yj) service repair manual (5yj0...fjkekfmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It outlines the required tools and steps to remove the housing which include removing mounting bolts, attaching lifting tools, and separating the housing from the cylinder block. The installation procedure specifies cleaning parts, positioning the housing with lifting tools attached, and installing mounting bolts with the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and flywheel housing from the engine block. It then describes how to clean the components, position the flywheel housing on dowels in the block, and torque the mounting bolts to specifications.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 diesel engine. It outlines the required tools and steps to remove the flywheel housing, which include removing the electric starting motor and flywheel first, then removing mounting bolts from the top and side of the housing. To install the flywheel housing, the instructions specify cleaning parts, attaching lifting tools, and reversing the removal steps and torque specifications.
Daewoo Doosan DX520LC Excavator Operation and Maintenance manual (Serial Numb...fusjejfjksaekmm
This is the most complete Operation and Maintenance Manual for the DAEWOO DOOSAN DX520LC EXCAVATOR . Operation and Maintenance Manual can come in handy especially when you have to do immediate repair to your DAEWOO DOOSAN DX520LC EXCAVATOR .Operation and Maintenance Manual comes with comprehensive details regarding technical data. Diagrams a complete list of DAEWOO DOOSAN DX520LC EXCAVATOR parts and is a must for the will not be dissatisfied.
Operation Manual Covers:
Safety
Operating Controls
Operation
Inspection, Maintenance and Adjustment
Transportation
Troubleshooting
Specifications
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
All pages are run off what you need & take it with you into the garage or save money $$ By doing your own repairs!These manuals make it easy for any skill level with these very easy to by step instructions!
Thanks for visiting!
Caterpillar cat 442 e backhoe loader (prefix pcr) service repair manual (pcr0...fusjejfjksaekmm
This document provides instructions for removing and installing a cylinder head on a Caterpillar C4.4 engine. The removal process involves draining coolant, removing various attached components, and loosening and removing bolts and dowels to lift the cylinder head off. The installation process describes cleaning surfaces, installing dowels and gaskets, tightening bolts in a specific sequence, and reinstalling attached components. Separate sections provide instructions for removing and installing lifter groups.
Caterpillar cat 442 e backhoe loader (prefix gkz) service repair manual (gkz0...fusjejfjksaekmm
The document provides disassembly instructions for a Caterpillar 442E backhoe loader transmission. It lists required tools and presents step-by-step instructions to disassemble the transmission into its major components. These include removing gears, shafts, seals, valves, yokes and other internal parts. Detailed diagrams illustrate each step in the process.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fusjejfjksaekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes:
1. Removing the oil pan and suction pipe before removing the engine oil pump assembly from the cylinder block using setscrews.
2. Cleaning and inspecting oil pump components before installation and lubricating parts with oil.
3. Installing the oil pump assembly using setscrews and checking backlash after installation.
4. Draining coolant before removing the water pump and fan. Removing the water pump involves setscrews and installing involves a new gasket and setscrews with sealant.
Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn0...fusjejfjksaekmm
This document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3054 engine.
It lists the required tools and gives step-by-step instructions to:
1. Remove the fuel injection pump by taking off bolts, covers, and disconnecting hoses.
2. Install the new fuel injection pump by replacing gaskets, connecting hoses, and aligning marks to ensure proper timing.
3. Tighten bolts and nuts to secure the pump in place.
Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn0...fusjejfjksaekmm
The document provides instructions for removing and installing the fuel injection pump on a Caterpillar 3054 engine. It describes:
1) The required tools and safety precautions for the job.
2) The step-by-step process for removing the fuel injection pump, which involves removing bolts, nuts, and covers to access the pump.
3) The step-by-step process for installing the new fuel injection pump, which involves cleaning and lubricating seals, aligning marks, and tightening bolts to specified torques.
Caterpillar cat 428 b backhoe loader (prefix 7ej) service repair manual (7ej0...fujjdfjkksekmem
This document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. The removal procedure involves removing bolts to detach the front housing from the cylinder block and oil pan. Installation requires replacing the gasket, applying sealant, installing bolts in the correct sequence, and ensuring proper alignment. Proper cleaning and containment of fluids is emphasized.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...ujfjjsjekkmsmd
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 436 c backhoe loader (prefix 2ar) service repair manual (2ar0...fusjejfskekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and bottom of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels using lifting brackets, and installing mounting bolts. Tools required include lifting brackets and bolts of the appropriate size.
Caterpillar cat 416 c backhoe loader (prefix 5yn) service repair manual (5yn0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 416C backhoe loader engine. It describes using lifting brackets and bolts to remove the housing. For installation, it instructs to clean mating surfaces, position the housing on dowels, and install bolts while supporting the housing with lifting brackets. Torque specifications are provided for tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 420 d backhoe loader (prefix bmc) service repair manual (bmc0...ujfjjskkemm
The document provides instructions for removing and installing a front tie rod on a 420D backhoe loader. It lists the required tools which include a transmission repair stand. The removal process first requires removing the front axle from the machine. Safety precautions are provided to release hydraulic pressure and ensure cool oil before removing any hydraulic components or lines.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Installing the housing by positioning it on the cylinder block and installing mounting bolts, taking care to keep parts clean of contaminants.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation. The document also notes to inspect and replace the oil pan seal if needed.
3) Reinstallation involves cleaning surfaces, attaching lifting tools, and torquing mounting bolts to secure the housing.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and housing before installation.
3) Installing the housing by positioning it on the cylinder block and installing mounting bolts, taking care to keep parts clean of contaminants.
Caterpillar cat 426 b backhoe loader (prefix 5yj) service repair manual (5yj0...fjkekfmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It outlines the required tools and steps to remove the housing which include removing mounting bolts, attaching lifting tools, and separating the housing from the cylinder block. The installation procedure specifies cleaning parts, positioning the housing with lifting tools attached, and installing mounting bolts with the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 diesel engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and flywheel housing from the engine block. It then describes how to clean the components, position the flywheel housing on dowels in the block, and torque the mounting bolts to specifications.
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 diesel engine. It outlines the required tools and steps to remove the flywheel housing, which include removing the electric starting motor and flywheel first, then removing mounting bolts from the top and side of the housing. To install the flywheel housing, the instructions specify cleaning parts, attaching lifting tools, and reversing the removal steps and torque specifications.
Similar to Caterpillar cat 438 b backhoe loader (prefix 3kk) service repair manual (3kk03000 and up) (10)
Daewoo Doosan DX520LC Excavator Operation and Maintenance manual (Serial Numb...fusjejfjksaekmm
This is the most complete Operation and Maintenance Manual for the DAEWOO DOOSAN DX520LC EXCAVATOR . Operation and Maintenance Manual can come in handy especially when you have to do immediate repair to your DAEWOO DOOSAN DX520LC EXCAVATOR .Operation and Maintenance Manual comes with comprehensive details regarding technical data. Diagrams a complete list of DAEWOO DOOSAN DX520LC EXCAVATOR parts and is a must for the will not be dissatisfied.
Operation Manual Covers:
Safety
Operating Controls
Operation
Inspection, Maintenance and Adjustment
Transportation
Troubleshooting
Specifications
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
All pages are run off what you need & take it with you into the garage or save money $$ By doing your own repairs!These manuals make it easy for any skill level with these very easy to by step instructions!
Thanks for visiting!
Caterpillar cat 442 e backhoe loader (prefix pcr) service repair manual (pcr0...fusjejfjksaekmm
This document provides instructions for removing and installing a cylinder head on a Caterpillar C4.4 engine. The removal process involves draining coolant, removing various attached components, and loosening and removing bolts and dowels to lift the cylinder head off. The installation process describes cleaning surfaces, installing dowels and gaskets, tightening bolts in a specific sequence, and reinstalling attached components. Separate sections provide instructions for removing and installing lifter groups.
Caterpillar cat 442 e backhoe loader (prefix gkz) service repair manual (gkz0...fusjejfjksaekmm
The document provides disassembly instructions for a Caterpillar 442E backhoe loader transmission. It lists required tools and presents step-by-step instructions to disassemble the transmission into its major components. These include removing gears, shafts, seals, valves, yokes and other internal parts. Detailed diagrams illustrate each step in the process.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fusjejfjksaekmm
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 3054C engine. It describes:
1. Removing the oil pan and suction pipe before removing the engine oil pump assembly from the cylinder block using setscrews.
2. Cleaning and inspecting oil pump components before installation and lubricating parts with oil.
3. Installing the oil pump assembly using setscrews and checking backlash after installation.
4. Draining coolant before removing the water pump and fan. Removing the water pump involves setscrews and installing involves a new gasket and setscrews with sealant.
Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn0...fusjejfjksaekmm
This document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3054 engine.
It lists the required tools and gives step-by-step instructions to:
1. Remove the fuel injection pump by taking off bolts, covers, and disconnecting hoses.
2. Install the new fuel injection pump by replacing gaskets, connecting hoses, and aligning marks to ensure proper timing.
3. Tighten bolts and nuts to secure the pump in place.
Caterpillar cat 436 c backhoe loader (prefix 9jn) service repair manual (9jn0...fusjejfjksaekmm
The document provides instructions for removing and installing the fuel injection pump on a Caterpillar 3054 engine. It describes:
1) The required tools and safety precautions for the job.
2) The step-by-step process for removing the fuel injection pump, which involves removing bolts, nuts, and covers to access the pump.
3) The step-by-step process for installing the new fuel injection pump, which involves cleaning and lubricating seals, aligning marks, and tightening bolts to specified torques.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fusjejfjksaekmm
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the flywheel housing, and lifting the housing off with tooling. For installation, the procedure is essentially reversed - cleaning surfaces, positioning the housing with tooling, and tightening mounting bolts to the specified torques. The document contains similar level of detail for other engine component procedures.
The document provides instructions for removing and installing an axle housing and flange on a 434F2 backhoe loader. The removal process involves removing bolts, nuts, plates, rings and shafts using various tools. Individual components like bearings, seals and bushings are then removed from the housing and flange. The assembly process reverses the removal steps, applying grease and torqueing bolts to specifications.
Caterpillar cat 434 f backhoe loader (prefix mtr) service repair manual (mtr0...fusjejfjksaekmm
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C4.4 engine. It outlines the required tools and parts, safety considerations, and step-by-step procedures. The removal process involves using a valve spring compressor tool to safely decompress the springs and remove the keepers and springs. The installation follows the reverse process, carefully compressing the springs with the tool to insert the keepers. Proper cleaning and inspection of parts is emphasized to prevent premature wear.
The document provides instructions for disassembling an axle housing on a 432F2 backhoe loader. It lists required tools and gives 26 steps to remove components such as brake discs, pistons, cylinders, gears, seals, and bearings. The overall goal is to disassemble the service brakes, differential, and bevel gear.
Caterpillar cat 420 d backhoe loader (prefix fdp) service repair manual (fdp0...fusjejfjksaekmm
This document provides instructions for disassembling and assembling the final drive, drive and steering axle housing, and related components of a 420D backhoe loader. The disassembly process involves removing components like planetary gears, bearings, seals, and snap rings from the final drive and hub. The assembly process provides detailed instructions and torque specifications for reinstalling these components in the reverse order. Tools needed are also listed. Safety precautions are noted such as using lifting devices to handle heavy components.
Caterpillar cat 420 d backhoe loader (prefix bmc) service repair manual (bmc0...fusjejfjksaekmm
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tools which include a transmission repair stand. The removal process first requires removing the front axle from the machine. Safety precautions are mentioned regarding hydraulic pressure even after the engine is stopped. The oil must be cool before removing any components.
CASE IH Magnum 280 Powershift Transmission (PST) Tier 4B Tractor Service Repa...fusjejfjksaekmm
This is the Highly Detailed factory service repair manual for theCASE IH MAGNUM 280 POWERSHIFT TRANSMISSION (PST) TIER 4B TRACTOR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.CASE IH MAGNUM 280 POWERSHIFT TRANSMISSION (PST) TIER 4B TRACTOR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
INTRODUCTION
Engine
Power coupling
Transmission
Four-Wheel Drive (4WD) system
Front axle system
Rear axle system
Power Take-Off (PTO)
Brakes and controls
Hydraulic systems
Hitches, drawbars, and implement couplings
Frames and ballasting
Steering
Wheels
Tracks and track suspension
Cab climate control
Electrical systems
Platform, cab, bodywork, and decals
Special Tool Index
Electrical Schematic
Hydraulic Schematic
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveCASE IH MAGNUM 280 POWERSHIFT TRANSMISSION (PST) TIER 4B TRACTOR Service Repair Workshop Manual.
Thanks for visiting!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438B BACKHOE LOADER 3KK
Configuration: 438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406238
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00546794
Typical Example. Different lifting device shown than what is called out in the Table.
Illustration 2 g00546793
1. Install Tool (A) and a suitable lifting device on flywheel (1) .
2. Remove bolts (3) and bearing housing (4) .
3. Remove six bolts (2) and the washers from the flywheel.
Note: The 3054 and 3056 marine engines used several bolt patterns to attach the flywheel to
the crankshaft. There are drilled holes that are not used in the crankshaft and in the
flywheel.
4. Use the suitable lifting device in order to remove flywheel (1) . The weight of flywheel (1)
and the flywheel ring gear is 53 kg (120 lb).
5. If removal of the flywheel ring gear is necessary, place an index mark on the chamfer of the
flywheel ring gear for the installation process.
Illustration 3 g00546795
2/3438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use a hammer and a punch in order to remove flywheel ring gear (5) from flywheel (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 08:19:27 UTC+0800 2019
3/3438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438B BACKHOE LOADER 3KK
Configuration: 438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 08:20:23 UTC+0800 2019
2/2438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438B BACKHOE LOADER 3KK
Configuration: 438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 08:21:18 UTC+0800 2019
3/3438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438B BACKHOE LOADER 3KK
Configuration: 438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 08:22:14 UTC+0800 2019
4/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438B BACKHOE LOADER 3KK
Configuration: 438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 08:23:10 UTC+0800 2019
4/4438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438B BACKHOE LOADER 3KK
Configuration: 438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 08:24:05 UTC+0800 2019
2/2438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 438B BACKHOE LOADER 3KK
Configuration: 438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIESEL ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742537
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00541748
Typical example
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Place Tooling (B) in the holes in order to remove crankshaft front seal (1). Use Tooling (B)
in each of the three holes to evenly remove the crankshaft front seal.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 27 08:25:01 UTC+0800 2019
2/2438B BACKHOE LOADER 3KK03000-UP (MACHINE) POWERED BY 3054 DIES...
2019/10/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...