This document provides instructions for installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes cleaning and preparing the seal and housing, then pressing the seal into place using the proper tool. It also provides separate instructions for installing the seal on engines with different housing assembly configurations.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 13 12:46:58 UTC+0800 2019
4/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 13 12:47:54 UTC+0800 2019
4/4436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 13 12:48:50 UTC+0800 2019
2/2436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742537
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00541748
Typical example
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Place Tooling (B) in the holes in order to remove crankshaft front seal (1). Use Tooling (B)
in each of the three holes to evenly remove the crankshaft front seal.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 13 12:49:46 UTC+0800 2019
2/2436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742545
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the housing for the crankshaft front seal and inspect the housing for damage.
2. Lubricate the lip of the crankshaft front seal with clean engine oil.
1/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00541748
3. Place crankshaft front oil seal (1) into the housing.
NOTICE
Ensure that the lip of the crankshaft front seal that is spring loaded is
facing toward the inside of the front housing and that it is square with
the bore of the housing for the crankshaft front seal.
Illustration 2 g00622033
4. Use Tooling (A) to install crankshaft front oil seal (1).
5. Apply clean engine oil on the area of the crankshaft pulley that will be in contact with
crankshaft front seal (1).
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Wed Nov 13 12:50:41 UTC+0800 2019
2/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02108315
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
B. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
C. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Illustration 1 g00640000
1. Remove bolts (1) and nuts (3) from the front cover.
2. Remove front cover (2) and the gasket from the cylinder block.
Wed Nov 13 12:51:37 UTC+0800 2019
1/2436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01694904
Front Cover - Install
SMCS - 1166-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
B 4C-5501 Front Cover Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all surfaces of the front housing and clean the front cover thoroughly.
2. If necessary, use Tool (A) to install the crankshaft front oil seal. Refer to Disassembly and
Assembly, "Crankshaft Front Seal - Install".
1/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00640000
Illustration 2 g00546873
3. Install a new gasket and front cover (2) .
4. Install two bolts (1) in order to hold the gasket and the cover in place.
5. Use Tool (B) and the bolts for the crankshaft pulley in order to center the front cover.
NOTICE
The location of the front cover is critical. If the front cover is not
centered, the backlash between the fuel injection pump gear and the
water pump gear could be affected. This could result in damage to the
fuel injection pump.
6. Install the remaining bolts (1) and the two nuts (3). Tighten the nuts and the bolts to a torque
of 22 N·m (16 lb ft).
End By:
2/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
c. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 13 12:52:33 UTC+0800 2019
3/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 1FR
Configuration: 436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02253357
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2264 Puller Group 1
B 173-9774 Wrench Bit 1
Start By:
A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g00556563
Note: It may be necessary to pin the fuel pump in order to maintain the correct timing.
Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove"for the correct
procedure.
1. Align the timing marks on the crankshaft gear, the camshaft gear, and the idler gear, as
shown.
2. Remove bolts (1) from idler gear (2) .
3. Remove idler gear (2) and retainer plate (3) .
Illustration 2 g00556757
4. Remove bushing (4) from idler gear (2) , if necessary.
5. Remove the bushing with a suitable puller. If the bushing cannot be removed with a puller,
grind the face off of one bushing. The remainder of the bushing can then be removed with a
press.
2/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g00556758
6. Remove idler gear hub (5) from the cylinder block.
7. Remove nut (6) and the spring washer from fuel injection pump gear (8) .
8. Remove bolts (7) from fuel injection pump gear (8) .
Note: Some fuel injection pump gears may have a tamper proof torx screw in place of one
of the four bolts. Use Tooling (B) to remove the tamper proof torx screw, if necessary.
9. Use Tooling (A) to remove fuel injection pump gear (8) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 13 12:53:29 UTC+0800 2019
3/3436C Backhoe Loader Center Pivot, Single Tilt 1FR01416-01421 (MACHINE) POW...
2019/11/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...