Caterpillar Cat 430E Backhoe Loader (Prefix EAT) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
430E Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 430E BACKHOE LOADER EAT
Configuration: 430E Backhoe Loader Center Pivot EAT00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders
Power Train
Media Number -RENR6475-13 Publication Date -01/07/2017 Date Updated -13/07/2017
i03664881
Steering Cylinder (Front) - Remove and Install
SMCS - 4303-010-FR
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 155-0695 Thread Lock Compound -
Start By:
A. Remove the front axle. Refer to Disassembly and Assembly, "Drive and Steering Axle
(Front) - Remove".
1/7
430E Backhoe Loader Center Pivot EAT00001-UP (MACHINE) POWERED BY 305...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01117223
2/7
2019/11/23

1. Place front axle assembly (2) onto suitable cribbing. Loosen nut (1) from each side.
2. Use Tooling (A) in order to disconnect tie rod (3) . Remove nut (1) and remove tie rod (3) .
Repeat for the other side.
3/7
2019/11/23

3. Remove bolts (4) and remove steering cylinder (5) .
Installation Procedure
4/7
2019/11/23

1. Install steering cylinder (5) . Apply Tooling (B) to bolts (4) and install bolts (4) . Tighten
bolts (4) to a torque of 460 N·m (340 lb ft).
5/7
2019/11/23

2. Install tie rod (3) . Repeat for the other side.
6/7
2019/11/23

3. Install nut (1) to each side of front axle assembly (2) . Tighten nut (1) to a torque of 220
N·m (162 lb ft).
End By: Install the front axle. Refer to Disassembly and Assembly, "Drive and Steering Axle
(Front) - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 23 22:08:32 UTC+0800 2019
7/7
2019/11/23

Shutdown SIS
Previous Screen
Power Train
i03664901
Steering Cylinder (Front) - Remove and Install - Two-Wheel
Drive
SMCS - 4303-010-FR
Removal Procedure
Table 1
Required Tools
A 155-0695 Thread Lock Compound -
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
B. Remove the tie rods. Refer to Disassembly and Assembly, "Tie Rod (Steering) (Front) -
Remove".
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/2
2019/11/23

1. Disconnect hose assemblies (1) and (2) . Remove bolts (4) and steering cylinder (3) .
1. Install steering cylinder (3) and bolts (4) . Apply Tooling (A) to bolts (4) and install bolts
(4) . Tighten bolts (4) to a torque of 460 N·m (340 lb ft). Connect hose assemblies (1) and
(2) .
End By: Install the tie rods. Refer to Disassembly and Assembly, "Tie Rod (Steering) (Front) -
Install".
Sat Nov 23 22:09:29 UTC+0800 2019
2/2
2019/11/23

Shutdown SIS
Previous Screen
Power Train
i02106590
Final Drive Planetary - Remove
SMCS - 4050-011; 4084-011
Removal Procedure
Start By:
a. Remove the wheel and tire. Refer to Disassembly and Assembly, "Wheel and Tire - Remove
and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the final drive planetary into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Final Drive Planetary (Axle) Oil - Change".
1/2
2019/11/23

2. Remove screws (2) and remove planetary carrier assembly (3) from wheel flange (1).
Sat Nov 23 22:10:25 UTC+0800 2019
2/2
2019/11/23

Shutdown SIS
Previous Screen
Power Train
i06167132
Final Drive Planetary - Disassemble
SMCS - 4050-015; 4084-015
Disassembly Procedure
Table 1
Required Tools
A 1P-1863 Retaining Ring Pliers 1
Start By:
a. Remove the final drive planetary. Refer to Disassembly and Assembly, "Final Drive
Planetary - Remove".
1/2
2019/11/23

1. Use Tooling (A) and remove retaining ring (1). Remove thrust washer (2), lock rings (3),
thrust washers (4), bearing (5) and planetary gear (6).
2. Repeat Step 1 for the remaining planetary gear assemblies.
Sat Nov 23 22:11:22 UTC+0800 2019
2/2
2019/11/23

Shutdown SIS
Previous Screen
Power Train
i02250853
Final Drive Planetary - Assemble
SMCS - 4050-016; 4084-016
Assembly Procedure
Table 1
Required Tools
A 1P-1863 Retaining Ring Pliers 1
1/2
2019/11/23

1. Position planetary gear (5) on a flat surface. Install one thrust washer (4) and one locking
ring (3). Install bearing (6) into planetary gear (5). Install the remaining thrust washer (4)
and the remaining locking ring (3). Install planetary gear (5) and the components into the
planetary carrier assembly. Install thrust washer (2). Use Tooling (A) and install retaining
ring (1) .
2. Repeat Step 1 for the remaining planetary gear assemblies.
End By: Install the final drive planetary. Refer to Disassembly and Assembly, "Final Drive
Planetary - Install".
Sat Nov 23 22:12:19 UTC+0800 2019
2/2
2019/11/23

Shutdown SIS
Previous Screen
Power Train
i02110388
Final Drive Planetary - Install
SMCS - 4050-012; 4084-012
1/2
2019/11/23

1. Position planetary carrier assembly (3) onto wheel flange (1). Install screws (2). Tighten
screws (2) to a torque of 25 N·m (18 lb ft).
2. Fill the final drive planetary with oil. Refer to Operation and Maintenance Manual,
"Capacities (Refill)" and refer to Operation and Maintenance Manual, "Final Drive
Planetary (Axle) Oil - Change".
End By:
a. Install the wheel and the tire. Refer to Disassembly and Assembly, "Wheel and Tire -
Remove and Install".
Sat Nov 23 22:13:16 UTC+0800 2019
2/2
2019/11/23

Shutdown SIS
Previous Screen
Power Train
i04818786
Drive Shaft (Front) - Remove and Install
SMCS - 3253-010-FR
Removal Procedure
Table 1
Required Tools
A 1U-7505 Hydraulic Jack 1
1/4
2019/11/23

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

1. Install Tooling (A) under guard (2) . Remove bolts (1) . Repeat for the other side. Use
Tooling (A) in order to lower guard (2) to the ground. The weight of guard (2) is
approximately 38 kg (85 lb).
2. Remove bolts (3) .
3. Remove bolts (5) and remove front drive shaft (4) .
2/4
2019/11/23

Caterpillar Cat 430E Backhoe Loader (Prefix EAT) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

More from shibi1322

More from shibi1322 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 430E Backhoe Loader (Prefix EAT) Service Repair Manual Instant Download.pdf