This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 3054 engines. It describes the removal and installation procedures for both Type 1/9RM and Type 2/7BJ engines. The procedures involve removing bolts and nuts, inspecting and replacing gaskets if needed, and reinstalling components in the reverse order of removal while keeping parts clean to prevent damage and wear.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01598347
Exhaust Manifold - Remove and Install - Type 2 Engines and
7BJ Engines
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
B. Remove the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold -
Remove and Install".
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00557287
Typical example
Illustration 2 g00557337
1. Remove exhaust manifold nuts or bolts (1) in reverse order of the numbered sequence.
2. Remove exhaust manifold (2) from the engine.
2/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00557351
Typical example
3. Remove exhaust manifold gaskets (3) from the engine.
4. Remove old sealant from stud threads.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00557351
Typical example
3/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 1. Inspect the condition of the gaskets. If the gaskets are damaged, use new parts for
replacement. Install exhaust manifold gaskets (3) on the cylinder head. Apply 4C-9507
Retaining Compound to the stud threads.
Illustration 5 g00557287
Typical example
Illustration 6 g00557337
NOTICE
Damage to the exhaust manifold can occur if the exhaust manifold is
not aligned and tightened correctly.
4/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 2. Install exhaust manifold (2) on the cylinder head.
Note: Some of the exhaust manifolds have large clearance holes for the bolts. If a new
exhaust manifold is installed ensure that the 148-7132 Ferrule mountings that are supplied
with the exhaust manifold are installed.
3. Install exhaust manifold nuts or bolts (1). Tighten the exhaust manifold nuts or bolts in the
numerical sequence to a torque of 44 N·m (33 lb ft).
End By:
a. Install the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold -
Remove and Install".
b. Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:42:57 UTC+0800 2019
5/5
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01068659
Exhaust Manifold - Remove and Install - Type 1 Engines and
9RM Engines
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Note: For a complete description of Type 1 and Type 2 Engines, refer to the Disassembly and
Assembly, "Engine Design" topic.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00542541
Typical example
1. Remove exhaust manifold nuts (1) .
2. Remove exhaust manifold (2) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00542541
Typical example
2/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Install the gasket and exhaust manifold (2) .
3. Install exhaust manifold nuts (1). Tighten the plated nuts to a torque of 44 N·m (32 lb ft).
Tighten the nuts that are not plated to a torque of 50 N·m (37 lb ft).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:43:52 UTC+0800 2019
3/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870246
Inlet Manifold - Remove - Type 2 Engines and 7BJ Engines
SMCS - 1058-011
Removal Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00557838
Typical example
1. Disconnect tube (1) from the air inlet heater.
2. Loosen hose clamps (3) and slide the hose toward the turbocharger.
3. Remove four bolts (2) and remove elbow (4) from the air inlet manifold.
Illustration 2 g00558245
Typical example
4. Remove bolts (5) that fasten air inlet manifold (6) to the engine.
5. Remove air inlet manifold (6) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:44:48 UTC+0800 2019
2/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870245
Inlet Manifold - Remove - Type 1 Engines and 9RM Engines
SMCS - 1058-011
Removal Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00545513
Typical example
Illustration 2 g00545514
Typical example
1. Disconnect electrical connector (5) for the air inlet heater.
2. Disconnect fuel line (6) to the air inlet heater.
3. Remove two bolts (7) that hold the bracket for fuel line (6) in position.
4. Loosen two hose clamps (8) and slide hose (9) toward the turbocharger.
5. Remove four bolts (3) in order to remove elbow (2) and gasket (4) .
6. Disconnect boost pressure hose (10) .
7. Remove bolts (12) that hold the turbocharger support to air inlet manifold (14) .
8. Remove bolts (13) that hold air inlet manifold (14) to the cylinder head.
2/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 9. Remove air inlet manifold (14) and gaskets (11) .
10. Remove seal (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:45:44 UTC+0800 2019
3/3
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870254
Inlet Manifold - Install - Type 1 Engines and 9RM Engines
SMCS - 1058-012
Installation Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the gaskets for wear or damage. If the gaskets are worn or damaged, use new parts
for replacement.
1/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 1 g00545514
Typical example
Illustration 2 g00545513
Typical example
2. Install seal (1) on the engine.
3. Position gaskets (11) and air inlet manifold (14) on the engine.
Note: Ensure that the front gaskets and the rear gaskets are installed with the notch at the
top left side. The center gasket can be installed in either direction.
4. Install bolts (13) .
5. Position the turbocharger support on air inlet manifold (14) and install bolts (12) .
6. Connect boost pressure hose (10) .
7. Install gasket (4) and elbow (2) with four bolts (3) .
8. Slide hose (9) in position and tighten hose clamps (8) .
9. Place the bracket for fuel line (6) in position and install two bolts (7) .
10. Connect fuel line (6) to the air inlet heater.
11. Connect electrical connector (5) for the air inlet heater.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:46:40 UTC+0800 2019
2/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1ER
Configuration: 426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02870255
Inlet Manifold - Install - Type 2 Engines and 7BJ Engines
SMCS - 1058-012
Installation Procedure
Note: For a complete description of Type 1 and Type 2 engines, refer to Disassembly and
Assembly, "Engine Design".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the gaskets for wear or damage. If the gaskets are worn or damaged, use new parts
for replacement.
1/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00558245
Typical example
2. Install the gasket and air inlet manifold (6) with bolts (5) . Tighten bolts (5) to a torque of 33
N·m (24 lb ft).
Illustration 2 g00557838
Typical example
3. Put the gasket and elbow (4) in position on the air inlet manifold.
4. Install four bolts (2) .
5. Slide the hose into position and tighten hose clamps (3) .
6. Connect tube (1) to the air inlet heater.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 19 11:47:35 UTC+0800 2019
2/2
426C Backhoe Loader Center Pivot, Single Tilt 1ER00001-00863 (MACHINE) POW...
2019/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...