This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and side of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the cylinder block and flywheel housing mating surfaces before installation.
3) Positioning the flywheel housing on the cylinder block and installing mounting bolts to secure it.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel using a lifting device and by removing bolts; 2) Install the flywheel by heating the flywheel ring gear, positioning the flywheel and ring gear, and tightening bolts; 3) Remove the crankshaft rear seal by removing housing bolts and separating the housing; 4) Install the crankshaft rear seal by pressing in the seal, lubricating surfaces, positioning the housing, and tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...jfksekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Installation instructions specify cleaning parts, placing the housing on the cylinder block, and tightening mounting bolts to secure the housing.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel using a lifting device and by removing bolts; 2) Install the flywheel by heating the flywheel ring gear, positioning the flywheel and ring gear, and tightening bolts; 3) Remove the crankshaft rear seal by removing housing bolts and separating the housing; 4) Install the crankshaft rear seal by pressing in the seal, lubricating surfaces, positioning the housing, and tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...jfksekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Installation instructions specify cleaning parts, placing the housing on the cylinder block, and tightening mounting bolts to secure the housing.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjufksefmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include lifting brackets and torque wrenches. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing onto dowels in the cylinder block, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Mercury mariner outboard 70 hp service repair manualfjeskfksmefmm
This document provides general specifications and maintenance instructions for Mercury outboard engines, including:
- Engine specifications like horsepower, cylinder configuration, ignition type, and recommended fluids.
- Removal of cowl components and filling the oil injection system.
- Power trim system operation and fluid level checking.
- Tilt angle adjustment for models with and without power trim.
- Connecting engine wiring harnesses and battery cable routing.
- Lubrication points and frequencies for ride-guide steering cables and throttle-shift linkages.
Honda marine outboard bf9.9 d service repair manualfjeskfksmefmm
The document promotes clicking a link to get more information. In a concise 3 sentences, it asks the reader to thank them for reading and then click a link for additional details.
2007 johnson evinrude outboard 90 hp service repair manualfjeskfksmefmm
This document provides information on service manuals for Evinrude outboard motors, including:
- The service manual covers Evinrude E-TEC 3-cylinder 79 cubic inch models.
- The parts catalog should be used with the service manual for part numbers and exploded views.
- Model and serial numbers are used to identify specific outboard models and options.
2007 johnson evinrude outboard 60 hp service repair manualfjeskfksmefmm
This document lists registered trademarks and intellectual property owned by various companies. It includes notices about safety information, models covered in the manual, identifying serial numbers, abbreviations used, and page layout descriptions. The document provides important legal and reference information for technicians working on outboard engines.
2003 sea doo gtx 4-tec international 6111 service repair manualfjeskfksmefmm
This 2003 Shop Manual provides service and repair information for Bombardier Sea-Doo watercraft models. It consists of 18 sections covering topics such as service tools, maintenance, troubleshooting, engine repair, cooling and fuel systems, electrical systems, and technical specifications. Technicians must follow the procedures outlined in the manual, including using the recommended tools and products, to correctly service these watercraft. The manual emphasizes safety and provides exploded views and diagrams to help accurately identify parts.
2003 sea doo gtx 4-tec 6112 service repair manualfjeskfksmefmm
This 2003 Shop Manual provides service and repair information for Bombardier Sea-Doo watercraft models. It consists of 18 sections covering topics such as service tools, maintenance, troubleshooting, engine repair, cooling and fuel systems, electrical systems, and technical specifications. Technicians must follow the procedures outlined in the manual, including using the recommended tools and products, to correctly service these watercraft. The manual emphasizes safety and provides exploded views and diagrams to help accurately identify parts.
2003 sea doo gti california (ultraviolet) 5567 service repair manualfjeskfksmefmm
This 2003 Shop Manual provides service and repair information for Bombardier Sea-Doo watercraft models. It consists of 18 sections covering topics such as service tools, maintenance procedures, troubleshooting, engine repair, electrical systems, and more. Technicians must follow the procedures outlined in the manual, using the recommended tools and products, when servicing these watercraft. The manual emphasizes safety and provides exploded views and other images to help correctly identify parts. It is intended to assist skilled mechanics in maintaining and repairing Bombardier Sea-Doo watercraft.
2002 sea doo rx di service repair manualfjeskfksmefmm
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains 16 sections covering service tools, maintenance, troubleshooting, engine systems, cooling systems, fuel systems, and other components. The manual provides exploded views, specifications, and step-by-step procedures for inspecting, diagnosing, and repairing issues with the watercraft. Technicians are advised to strictly follow safety notices, torque specifications, and use recommended special tools when servicing components.
2002 sea doo lrv di service repair manualfjeskfksmefmm
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains 16 sections covering service tools, maintenance, troubleshooting, engine systems, cooling systems, fuel systems, and other components. The manual provides exploded views, specifications, and step-by-step procedures for technicians to correctly service and repair these watercraft. Safety notices are included throughout to warn technicians of important hazards.
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains 16 sections covering topics such as service tools, maintenance, troubleshooting, engine systems, cooling systems, and more. The manual provides exploded views of components and step-by-step instructions for repairs and replacements. Abbreviations used in the manual are also defined for reference.
2002 sea doo gtx rfi service repair manualfjeskfksmefmm
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains sections on service tools, maintenance, troubleshooting, engine systems, cooling systems, fuel systems, and other components. The manual provides technical information, diagrams, and procedures for servicing these watercraft models. It is intended to assist mechanical technicians in correctly servicing and repairing the 2002 Sea-Doo watercraft.
This document is the 2001 shop manual for Sea-Doo watercraft models GS, GTI, GTS, GTX, XP, RX, and their variants. It contains sections on service tools, maintenance procedures, troubleshooting, engine systems, cooling, fuel, lubrication, electrical, propulsion, steering, suspension, hull/body, technical specifications, and wiring diagrams. The manual is intended as a guide for technicians already familiar with repairing these watercraft and recommends using genuine Bombardier parts. Safety notices indicate that precautions should be taken and proper tools used when servicing to avoid damaging components or creating safety hazards.
1999 sea doo sportster 1800 service repair manualfjeskfksmefmm
This shop manual covers the 1999 models of the Sportster and Challenger jet boats. It provides service information on maintenance, troubleshooting, engine systems, electrical systems, and other components. New service tools, lift kits, and service products are introduced to technicians.
1998 mercury mariner outboards 2.5hp 275hp service repair manualfjeskfksmefmm
The document encourages the reader to click a link for more information after thanking them for reading. It provides a brief message asking the reader to click a link without providing many other details.
More Related Content
Similar to Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr01517 02191)
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjufksefmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include lifting brackets and torque wrenches. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing onto dowels in the cylinder block, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Similar to Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr01517 02191) (7)
Mercury mariner outboard 70 hp service repair manualfjeskfksmefmm
This document provides general specifications and maintenance instructions for Mercury outboard engines, including:
- Engine specifications like horsepower, cylinder configuration, ignition type, and recommended fluids.
- Removal of cowl components and filling the oil injection system.
- Power trim system operation and fluid level checking.
- Tilt angle adjustment for models with and without power trim.
- Connecting engine wiring harnesses and battery cable routing.
- Lubrication points and frequencies for ride-guide steering cables and throttle-shift linkages.
Honda marine outboard bf9.9 d service repair manualfjeskfksmefmm
The document promotes clicking a link to get more information. In a concise 3 sentences, it asks the reader to thank them for reading and then click a link for additional details.
2007 johnson evinrude outboard 90 hp service repair manualfjeskfksmefmm
This document provides information on service manuals for Evinrude outboard motors, including:
- The service manual covers Evinrude E-TEC 3-cylinder 79 cubic inch models.
- The parts catalog should be used with the service manual for part numbers and exploded views.
- Model and serial numbers are used to identify specific outboard models and options.
2007 johnson evinrude outboard 60 hp service repair manualfjeskfksmefmm
This document lists registered trademarks and intellectual property owned by various companies. It includes notices about safety information, models covered in the manual, identifying serial numbers, abbreviations used, and page layout descriptions. The document provides important legal and reference information for technicians working on outboard engines.
2003 sea doo gtx 4-tec international 6111 service repair manualfjeskfksmefmm
This 2003 Shop Manual provides service and repair information for Bombardier Sea-Doo watercraft models. It consists of 18 sections covering topics such as service tools, maintenance, troubleshooting, engine repair, cooling and fuel systems, electrical systems, and technical specifications. Technicians must follow the procedures outlined in the manual, including using the recommended tools and products, to correctly service these watercraft. The manual emphasizes safety and provides exploded views and diagrams to help accurately identify parts.
2003 sea doo gtx 4-tec 6112 service repair manualfjeskfksmefmm
This 2003 Shop Manual provides service and repair information for Bombardier Sea-Doo watercraft models. It consists of 18 sections covering topics such as service tools, maintenance, troubleshooting, engine repair, cooling and fuel systems, electrical systems, and technical specifications. Technicians must follow the procedures outlined in the manual, including using the recommended tools and products, to correctly service these watercraft. The manual emphasizes safety and provides exploded views and diagrams to help accurately identify parts.
2003 sea doo gti california (ultraviolet) 5567 service repair manualfjeskfksmefmm
This 2003 Shop Manual provides service and repair information for Bombardier Sea-Doo watercraft models. It consists of 18 sections covering topics such as service tools, maintenance procedures, troubleshooting, engine repair, electrical systems, and more. Technicians must follow the procedures outlined in the manual, using the recommended tools and products, when servicing these watercraft. The manual emphasizes safety and provides exploded views and other images to help correctly identify parts. It is intended to assist skilled mechanics in maintaining and repairing Bombardier Sea-Doo watercraft.
2002 sea doo rx di service repair manualfjeskfksmefmm
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains 16 sections covering service tools, maintenance, troubleshooting, engine systems, cooling systems, fuel systems, and other components. The manual provides exploded views, specifications, and step-by-step procedures for inspecting, diagnosing, and repairing issues with the watercraft. Technicians are advised to strictly follow safety notices, torque specifications, and use recommended special tools when servicing components.
2002 sea doo lrv di service repair manualfjeskfksmefmm
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains 16 sections covering service tools, maintenance, troubleshooting, engine systems, cooling systems, fuel systems, and other components. The manual provides exploded views, specifications, and step-by-step procedures for technicians to correctly service and repair these watercraft. Safety notices are included throughout to warn technicians of important hazards.
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains 16 sections covering topics such as service tools, maintenance, troubleshooting, engine systems, cooling systems, and more. The manual provides exploded views of components and step-by-step instructions for repairs and replacements. Abbreviations used in the manual are also defined for reference.
2002 sea doo gtx rfi service repair manualfjeskfksmefmm
This document is the 2002 Shop Manual for Sea-Doo GTX DI and GTX 4-TEC watercraft. It contains sections on service tools, maintenance, troubleshooting, engine systems, cooling systems, fuel systems, and other components. The manual provides technical information, diagrams, and procedures for servicing these watercraft models. It is intended to assist mechanical technicians in correctly servicing and repairing the 2002 Sea-Doo watercraft.
This document is the 2001 shop manual for Sea-Doo watercraft models GS, GTI, GTS, GTX, XP, RX, and their variants. It contains sections on service tools, maintenance procedures, troubleshooting, engine systems, cooling, fuel, lubrication, electrical, propulsion, steering, suspension, hull/body, technical specifications, and wiring diagrams. The manual is intended as a guide for technicians already familiar with repairing these watercraft and recommends using genuine Bombardier parts. Safety notices indicate that precautions should be taken and proper tools used when servicing to avoid damaging components or creating safety hazards.
1999 sea doo sportster 1800 service repair manualfjeskfksmefmm
This shop manual covers the 1999 models of the Sportster and Challenger jet boats. It provides service information on maintenance, troubleshooting, engine systems, electrical systems, and other components. New service tools, lift kits, and service products are introduced to technicians.
1998 mercury mariner outboards 2.5hp 275hp service repair manualfjeskfksmefmm
The document encourages the reader to click a link for more information after thanking them for reading. It provides a brief message asking the reader to click a link without providing many other details.
1997 sea doo speedster 5605 service repair manualfjeskfksmefmm
This document is the 1997 Shop Manual for Bombardier Sea-Doo jet boats. It contains 12 sections covering maintenance, troubleshooting, engine, cooling, fuel, lubrication, electrical, propulsion, steering, hull/deck, technical data and wiring diagrams. The manual provides detailed instructions and torque specifications for repair and servicing of various components. It is intended to be used by trained technicians for maintenance and repairs.
1997 mercury mariner outboards 2.5hp 275hp service repair manualfjeskfksmefmm
The document promotes clicking a link to get more information. In a concise 3 sentences, it asks the reader to thank them for reading and then click a link for additional details.
1996 sea doo sportster 5894 service repair manualfjeskfksmefmm
This document is a 1996 Bombardier jet boat shop manual. It contains sections on service tools, maintenance, troubleshooting, engine systems, electrical systems, and other components. The manual provides technical information, diagrams, and instructions for repairing and servicing Bombardier watercraft. It is intended to be used by trained technicians who are familiar with maintenance and repair procedures.
1996 mercury mariner outboards 2.5hp 275hp service repair manualfjeskfksmefmm
This short document encourages the reader to click on a link for more information after thanking them for reading. It asks the reader to click on a link and provides no other context or details about the topic of the information.
1987 mercury outboard engine 40 hp 115hp service repair manualfjeskfksmefmm
The document promotes clicking a link to get more information. In a single short paragraph, it thanks the reader for reading and prompts them to click a link for additional details. The summary focuses on the key points of thanking the reader and directing them to click a link.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406238
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00546794
Typical Example. Different lifting device shown than what is called out in the Table.
Illustration 2 g00546793
1. Install Tool (A) and a suitable lifting device on flywheel (1) .
2. Remove bolts (3) and bearing housing (4) .
3. Remove six bolts (2) and the washers from the flywheel.
Note: The 3054 and 3056 marine engines used several bolt patterns to attach the flywheel to
the crankshaft. There are drilled holes that are not used in the crankshaft and in the
flywheel.
4. Use the suitable lifting device in order to remove flywheel (1) . The weight of flywheel (1)
and the flywheel ring gear is 53 kg (120 lb).
5. If removal of the flywheel ring gear is necessary, place an index mark on the chamfer of the
flywheel ring gear for the installation process.
Illustration 3 g00546795
2/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use a hammer and a punch in order to remove flywheel ring gear (5) from flywheel (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:24:34 UTC+0800 2019
3/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:25:30 UTC+0800 2019
2/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:26:26 UTC+0800 2019
3/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:27:22 UTC+0800 2019
4/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:28:17 UTC+0800 2019
4/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:29:13 UTC+0800 2019
2/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...