This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and side of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation.
3) Positioning the flywheel housing on the cylinder block and installing mounting bolts to secure it.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel using a lifting device and by removing bolts; 2) Install the flywheel by heating the flywheel ring gear, positioning the flywheel and ring gear, and tightening bolts; 3) Remove the crankshaft rear seal by removing housing bolts and separating the housing; 4) Install the crankshaft rear seal by pressing in the seal, lubricating surfaces, positioning the housing, and tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...jfksekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Installation instructions specify cleaning parts, placing the housing on the cylinder block, and tightening mounting bolts to secure the housing.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel using a lifting device and by removing bolts; 2) Install the flywheel by heating the flywheel ring gear, positioning the flywheel and ring gear, and tightening bolts; 3) Remove the crankshaft rear seal by removing housing bolts and separating the housing; 4) Install the crankshaft rear seal by pressing in the seal, lubricating surfaces, positioning the housing, and tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...jfksekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Installation instructions specify cleaning parts, placing the housing on the cylinder block, and tightening mounting bolts to secure the housing.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjufksefmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include lifting brackets and torque wrenches. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing onto dowels in the cylinder block, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
John deere xuv 850 d gator utility vehicle service repair manual (tm1737)fjjskekksemmrt
This technical manual provides service and repair information for the John Deere XUV 850D Gator utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, diagnostics, and repairs. It aims to keep all information for a particular system together to aid technicians in servicing this vehicle. Safety is the first section and warns of dangers of fuels and working around heaters or other fire hazards.
John deere xuv 620i gator utility vehicle service repair manualfjjskekksemmrt
This technical manual provides service and repair information for the John Deere Gator XUV 620i utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, maintenance, and repairs. It is intended as a resource for experienced technicians working with this product. Safety notices and procedures are highlighted throughout to warn of hazards during service.
John deere tractors 5075 e tractor (north america) service repair manual (tm9...fjjskekksemmrt
This document is a technical manual providing repair instructions for John Deere 5055E, 5065E, and 5075E tractors. It outlines several safety precautions including recognizing safety symbols, understanding signal words, following safety instructions, handling fluids safely to avoid fires, preventing battery explosions, preparing for emergencies, preventing acid burns, safely servicing the cooling system, avoiding high-pressure fluids, properly parking and supporting the machine, and wearing protective clothing. The manual is intended for experienced technicians and provides essential tool recommendations, component repair instructions, and specifications.
John deere 320 d skid steer loader (eh controls) service repair manual (tm11407)fjjskekksemmrt
This document provides safety information and instructions for technicians working on 318D, 319D, 320D, and 323D skid steer loaders. It emphasizes the importance of following all safety precautions when inspecting or servicing the machine, including wearing protective equipment, avoiding contact with moving parts and high-pressure fluids, preventing fires, and working in a ventilated area to avoid exhaust inhalation. Technicians are instructed to thoroughly read all safety messages in the manual and on the machine before performing any work.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...fjjskekksemmrt
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. The summary is:
1. To remove the oil pump, remove the engine oil pan, front housing, or No. 1 crankshaft main bearing cap. Then remove retaining rings, gears, and bolts to separate the pump.
2. To install the oil pump, clean all parts and apply Loctite to shafts if replaced. Fill the pump with oil and install gears, bolts, and retaining rings in reverse order of removal. Ensure proper backlash between gears.
3. Additional steps include removing and installing related components like the oil relief valve, suction pipe, and
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It lists the required tools and safety notices. The removal procedure involves removing mounting bolts from the top and bottom of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and steps to remove the flywheel, flywheel housing, and rear crankshaft seal. It then details how to clean surfaces, install a new rear crankshaft seal and gasket, and reinstall the flywheel housing and flywheel. Special care is required to contain fluids, clean parts, and properly torque bolts. Diagrams illustrate the component locations and tooling.
Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr0...fjjskekksemmrt
1. The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 engine.
2. The removal procedure involves removing attaching bolts and removing the cover and gasket.
3. The installation procedure specifies applying a gasket sealant, installing a new gasket and cover, and tightening the attaching bolts to the specified torque.
Case ih magnum 280 tractor service repair manual (pin zjrf94001 and above)fjjskekksemmrt
This document is a service manual for Magnum 250, 280, 310, 340, 310 Rowtrac, and 340 Rowtrac tractors with Powershift Transmissions (PST) from CNH Industrial America LLC. It contains over 50 sections that provide information on systems including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section includes detailed component information, diagrams, specifications, and repair or replacement procedures.
Nissan forklift o frame -opc series service repair manualfjjskekksemmrt
This document is a service manual for ATLET picking trucks in the OP series. It provides general information and technical data about the trucks. Some key points covered include:
- How to use the manual and find relevant information for specific problems or procedures.
- Important changes that have been made to OP models over time that should be considered during service.
- Approved lifting points on the trucks when lifting for service or with a jack.
- Important safety instructions that must be followed when working on the trucks, such as securing the truck, disconnecting the battery, and preventing unintended movement.
- General safety risks associated with working on fork trucks and the precautions that should be taken regarding fire,
Massey ferguson mf 130 tractor service parts catalogue manualfjjskekksemmrt
This document provides part numbers and descriptions for engine and starter components for Massey Ferguson MF 122/130 tractors. It includes 33 items related to the engine, accessories, dynamo and starter motor. Each item lists applicable part numbers, quantities, descriptions and comments clarifying application based on manufacturer or country.
Massey ferguson 4320 tractors service parts catalogue manual (part number 81...fjjskekksemmrt
This document provides parts information for an engine installation on Massey Ferguson 4315/4320 tractors. It contains 3 pages of documentation with details about 35 individual parts for the engine, including the engine block, cylinder head, valves, pistons, connecting rods and other components. The parts are identified by number and include the part name or description and quantity required. Tolerances or specifications are provided for some parts.
John deere tractors 5065 e tractor (north america) service repair manual (tm9...fjjskekksemmrt
This document is a technical manual providing repair instructions for John Deere 5055E, 5065E, and 5075E tractors. It outlines several safety precautions including recognizing safety symbols, understanding signal words, following safety instructions, handling fluids safely to avoid fires, preventing battery explosions, preparing for emergencies, preventing acid burns, safely servicing the cooling system, avoiding high-pressure fluids, properly parking and supporting the machine, and wearing protective clothing. The manual is intended for experienced technicians and provides essential tool recommendations, component repair instructions, and specifications.
John deere 319 d skid steer loader (eh controls) service repair manual (tm11407)fjjskekksemmrt
This document provides safety information and instructions for technicians working on 318D, 319D, 320D, and 323D skid steer loaders. It emphasizes the importance of following all safety precautions when inspecting or servicing the machine, including wearing protective equipment, avoiding contact with moving parts and high-pressure fluids, preventing fires, and working in a ventilated area to avoid exhaust inhalation. Technicians are instructed to thoroughly read all safety messages in the manual and on the machine before performing any work.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing, disassembling, and assembling pistons and connecting rods for a 3054 engine. The removal process involves removing the cylinder head, oil pump, and piston cooling jets. Pistons are then pushed out of the cylinder block. Disassembly requires using tools to remove piston rings and pins. Assembly requires cleaning, lubricating, and installing components in the reverse order of removal, ensuring proper alignment and torque specifications are followed.
More Related Content
Similar to Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr01517 02191)
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjufksefmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include lifting brackets and torque wrenches. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing onto dowels in the cylinder block, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Similar to Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr01517 02191) (7)
John deere xuv 850 d gator utility vehicle service repair manual (tm1737)fjjskekksemmrt
This technical manual provides service and repair information for the John Deere XUV 850D Gator utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, diagnostics, and repairs. It aims to keep all information for a particular system together to aid technicians in servicing this vehicle. Safety is the first section and warns of dangers of fuels and working around heaters or other fire hazards.
John deere xuv 620i gator utility vehicle service repair manualfjjskekksemmrt
This technical manual provides service and repair information for the John Deere Gator XUV 620i utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, maintenance, and repairs. It is intended as a resource for experienced technicians working with this product. Safety notices and procedures are highlighted throughout to warn of hazards during service.
John deere tractors 5075 e tractor (north america) service repair manual (tm9...fjjskekksemmrt
This document is a technical manual providing repair instructions for John Deere 5055E, 5065E, and 5075E tractors. It outlines several safety precautions including recognizing safety symbols, understanding signal words, following safety instructions, handling fluids safely to avoid fires, preventing battery explosions, preparing for emergencies, preventing acid burns, safely servicing the cooling system, avoiding high-pressure fluids, properly parking and supporting the machine, and wearing protective clothing. The manual is intended for experienced technicians and provides essential tool recommendations, component repair instructions, and specifications.
John deere 320 d skid steer loader (eh controls) service repair manual (tm11407)fjjskekksemmrt
This document provides safety information and instructions for technicians working on 318D, 319D, 320D, and 323D skid steer loaders. It emphasizes the importance of following all safety precautions when inspecting or servicing the machine, including wearing protective equipment, avoiding contact with moving parts and high-pressure fluids, preventing fires, and working in a ventilated area to avoid exhaust inhalation. Technicians are instructed to thoroughly read all safety messages in the manual and on the machine before performing any work.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...fjjskekksemmrt
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. The summary is:
1. To remove the oil pump, remove the engine oil pan, front housing, or No. 1 crankshaft main bearing cap. Then remove retaining rings, gears, and bolts to separate the pump.
2. To install the oil pump, clean all parts and apply Loctite to shafts if replaced. Fill the pump with oil and install gears, bolts, and retaining rings in reverse order of removal. Ensure proper backlash between gears.
3. Additional steps include removing and installing related components like the oil relief valve, suction pipe, and
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It lists the required tools and safety notices. The removal procedure involves removing mounting bolts from the top and bottom of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and steps to remove the flywheel, flywheel housing, and rear crankshaft seal. It then details how to clean surfaces, install a new rear crankshaft seal and gasket, and reinstall the flywheel housing and flywheel. Special care is required to contain fluids, clean parts, and properly torque bolts. Diagrams illustrate the component locations and tooling.
Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr0...fjjskekksemmrt
1. The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 engine.
2. The removal procedure involves removing attaching bolts and removing the cover and gasket.
3. The installation procedure specifies applying a gasket sealant, installing a new gasket and cover, and tightening the attaching bolts to the specified torque.
Case ih magnum 280 tractor service repair manual (pin zjrf94001 and above)fjjskekksemmrt
This document is a service manual for Magnum 250, 280, 310, 340, 310 Rowtrac, and 340 Rowtrac tractors with Powershift Transmissions (PST) from CNH Industrial America LLC. It contains over 50 sections that provide information on systems including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section includes detailed component information, diagrams, specifications, and repair or replacement procedures.
Nissan forklift o frame -opc series service repair manualfjjskekksemmrt
This document is a service manual for ATLET picking trucks in the OP series. It provides general information and technical data about the trucks. Some key points covered include:
- How to use the manual and find relevant information for specific problems or procedures.
- Important changes that have been made to OP models over time that should be considered during service.
- Approved lifting points on the trucks when lifting for service or with a jack.
- Important safety instructions that must be followed when working on the trucks, such as securing the truck, disconnecting the battery, and preventing unintended movement.
- General safety risks associated with working on fork trucks and the precautions that should be taken regarding fire,
Massey ferguson mf 130 tractor service parts catalogue manualfjjskekksemmrt
This document provides part numbers and descriptions for engine and starter components for Massey Ferguson MF 122/130 tractors. It includes 33 items related to the engine, accessories, dynamo and starter motor. Each item lists applicable part numbers, quantities, descriptions and comments clarifying application based on manufacturer or country.
Massey ferguson 4320 tractors service parts catalogue manual (part number 81...fjjskekksemmrt
This document provides parts information for an engine installation on Massey Ferguson 4315/4320 tractors. It contains 3 pages of documentation with details about 35 individual parts for the engine, including the engine block, cylinder head, valves, pistons, connecting rods and other components. The parts are identified by number and include the part name or description and quantity required. Tolerances or specifications are provided for some parts.
John deere tractors 5065 e tractor (north america) service repair manual (tm9...fjjskekksemmrt
This document is a technical manual providing repair instructions for John Deere 5055E, 5065E, and 5075E tractors. It outlines several safety precautions including recognizing safety symbols, understanding signal words, following safety instructions, handling fluids safely to avoid fires, preventing battery explosions, preparing for emergencies, preventing acid burns, safely servicing the cooling system, avoiding high-pressure fluids, properly parking and supporting the machine, and wearing protective clothing. The manual is intended for experienced technicians and provides essential tool recommendations, component repair instructions, and specifications.
John deere 319 d skid steer loader (eh controls) service repair manual (tm11407)fjjskekksemmrt
This document provides safety information and instructions for technicians working on 318D, 319D, 320D, and 323D skid steer loaders. It emphasizes the importance of following all safety precautions when inspecting or servicing the machine, including wearing protective equipment, avoiding contact with moving parts and high-pressure fluids, preventing fires, and working in a ventilated area to avoid exhaust inhalation. Technicians are instructed to thoroughly read all safety messages in the manual and on the machine before performing any work.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing, disassembling, and assembling pistons and connecting rods for a 3054 engine. The removal process involves removing the cylinder head, oil pump, and piston cooling jets. Pistons are then pushed out of the cylinder block. Disassembly requires using tools to remove piston rings and pins. Assembly requires cleaning, lubricating, and installing components in the reverse order of removal, ensuring proper alignment and torque specifications are followed.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to:
1) Support the engine and remove mounting bolts from the top and sides of the flywheel housing.
2) Attach lifting devices to the housing and remove it from the cylinder block.
3) Clean the mating surfaces of the block and housing before reinstalling the housing using lifting devices and bolts, ensuring proper torque is applied.
Case 865 b awd tier 0 tier 1 tier 2 tier 3 graders service repair manualfjjskekksemmrt
This document provides information about engines for various grader models, including specifications and troubleshooting procedures. It contains sections on the engine diagnostic tool, fails diagnostics for engines that do not start, and specifications for Tier 3 engines. Torque specifications and instructions for removing and installing components are also included.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fjjskekksemmrt
This document provides instructions for removing and installing a cylinder head on a 3054 engine. The removal procedure involves draining fluids, removing various components attached to the cylinder head like the air inlet manifold and fuel injection nozzles, and then loosening bolts to lift the cylinder head off. The installation procedure specifies cleaning surfaces, positioning the cylinder head gasket and cylinder head, tightening bolts in a sequence, and further tightening bolts using a degree wheel. Tools required include guide bolts and a degree wheel.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting devices to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the flywheel ring gear, installing it on the flywheel, positioning the flywheel and installing bolts with a lifting tool.
3) Remove the crankshaft rear seal housing by removing bolts and housing from the cylinder block.
4) Install the crankshaft rear seal by pressing the seal into
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and sides of the flywheel housing and using lifting tools to remove the housing, which weighs approximately 70 lbs.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation. The instructions specify installing the housing by aligning it on the cylinder block and securing it with mounting bolts.
3) Recommendations to keep parts clean and contain fluids to prevent contamination or spills during the repair process.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406238
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00546794
Typical Example. Different lifting device shown than what is called out in the Table.
Illustration 2 g00546793
1. Install Tool (A) and a suitable lifting device on flywheel (1) .
2. Remove bolts (3) and bearing housing (4) .
3. Remove six bolts (2) and the washers from the flywheel.
Note: The 3054 and 3056 marine engines used several bolt patterns to attach the flywheel to
the crankshaft. There are drilled holes that are not used in the crankshaft and in the
flywheel.
4. Use the suitable lifting device in order to remove flywheel (1) . The weight of flywheel (1)
and the flywheel ring gear is 53 kg (120 lb).
5. If removal of the flywheel ring gear is necessary, place an index mark on the chamfer of the
flywheel ring gear for the installation process.
Illustration 3 g00546795
2/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use a hammer and a punch in order to remove flywheel ring gear (5) from flywheel (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:24:34 UTC+0800 2019
3/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:25:30 UTC+0800 2019
2/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:26:26 UTC+0800 2019
3/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:27:22 UTC+0800 2019
4/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:28:17 UTC+0800 2019
4/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:29:13 UTC+0800 2019
2/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...