The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader, including:
- Removing the transmission, torque converter, gears, shafts, and other components using various tools.
- Dismantling the solenoid valve by removing springs, pistons, seals, and other internal parts.
- Taking apart the direct drive front and rear output shafts by removing bearings, gears, seals, and synchronizer assemblies.
- Instructions include safety warnings and notes about releasing spring forces. Detailed illustrations supplement the text instructions.
The document provides instructions for disassembling and assembling components of a 420F2 Backhoe Loader transmission. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Safety warnings are included to release spring forces carefully using the proper tools to avoid injury from propelled parts. Detailed illustrations supplement each step of the process.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to handle parts with compressed springs. Tools required are listed.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to release springs carefully due to risk of being struck by propelled parts.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to release springs carefully due to risk of being struck by propelled parts.
The document is a service repair manual that provides disassembly and assembly instructions for a 434F2 backhoe loader powertrain. It details how to disassemble the transmission's direct drive, front output shaft, rear output shaft, direct drive shaft, and reverse shaft. The summary includes removing various components like gears, bearings, seals, shafts, and fasteners using specialized tools in a specific sequence while taking safety precautions for parts under spring tension.
This document provides disassembly instructions for a 434F2 backhoe loader transmission. It describes how to remove various transmission components including the torque converter, gears, shafts, bearings, seals and other parts. Detailed steps and illustrations are provided to guide the removal of these components from both the front and rear sections of the direct drive transmission. Safety warnings are included to prevent injury from parts under spring tension.
This document provides disassembly instructions for a 434F2 backhoe loader transmission. It describes how to remove various transmission components including the torque converter, gears, shafts, bearings, seals and other parts. Detailed steps and illustrations are provided to guide the removal of these components from both the front and rear sections of the direct drive transmission. Safety warnings are included to prevent injury from parts under spring tension.
The document is a service repair manual that provides disassembly and assembly instructions for a 434F2 backhoe loader powertrain. It describes how to disassemble the transmission's direct drive, front output shaft, rear output shaft, direct drive shaft, and reverse shaft. The summary includes removing various components like gears, bearings, seals, shafts, and fasteners using specialized tools in a specific sequence. Safety precautions are provided to avoid injury from released spring forces.
The document provides instructions for disassembling and assembling components of a 420F2 Backhoe Loader transmission. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Safety warnings are included to release spring forces carefully using the proper tools to avoid injury from propelled parts. Detailed illustrations supplement each step of the process.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to handle parts with compressed springs. Tools required are listed.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to release springs carefully due to risk of being struck by propelled parts.
The document provides instructions for disassembling and assembling components of the transmission for a 420F2 Backhoe Loader. It describes removing the transmission from the machine and then disassembling its internal components like gears, shafts, bearings, and solenoids. Detailed steps are given for disassembling the direct drive front and rear output shafts. Safety warnings are included to release springs carefully due to risk of being struck by propelled parts.
The document is a service repair manual that provides disassembly and assembly instructions for a 434F2 backhoe loader powertrain. It details how to disassemble the transmission's direct drive, front output shaft, rear output shaft, direct drive shaft, and reverse shaft. The summary includes removing various components like gears, bearings, seals, shafts, and fasteners using specialized tools in a specific sequence while taking safety precautions for parts under spring tension.
This document provides disassembly instructions for a 434F2 backhoe loader transmission. It describes how to remove various transmission components including the torque converter, gears, shafts, bearings, seals and other parts. Detailed steps and illustrations are provided to guide the removal of these components from both the front and rear sections of the direct drive transmission. Safety warnings are included to prevent injury from parts under spring tension.
This document provides disassembly instructions for a 434F2 backhoe loader transmission. It describes how to remove various transmission components including the torque converter, gears, shafts, bearings, seals and other parts. Detailed steps and illustrations are provided to guide the removal of these components from both the front and rear sections of the direct drive transmission. Safety warnings are included to prevent injury from parts under spring tension.
The document is a service repair manual that provides disassembly and assembly instructions for a 434F2 backhoe loader powertrain. It describes how to disassemble the transmission's direct drive, front output shaft, rear output shaft, direct drive shaft, and reverse shaft. The summary includes removing various components like gears, bearings, seals, shafts, and fasteners using specialized tools in a specific sequence. Safety precautions are provided to avoid injury from released spring forces.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals.
4. Disassembling the scavenge pump by removing O-rings, bearings, shafts, and gears.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before disassembling the recoil spring components.
3. Reassembling the recoil spring components and using the tooling bench to apply controlled compression for assembly. Proper centering and leveling of the assembly is critical.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 657E wheel tractor. The removal procedure involves using various tools to disassemble the rear gear components and adapter assemblies. The installation procedure describes reassembling these components and requires pressing or installing bearings and seals using a driver group or press. Special care must be taken to keep parts clean and lubricated. The flywheel removal uses tools to secure the crankshaft gear and hoist the heavy flywheel off the engine.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using punch tools or pullers
The document provides instructions for installing the crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes heating the ring gear to 300°C before installing it on the flywheel. It also details installing guide bolts and lifting brackets to position the flywheel, applying grease to the bolt threads, and torquing the bolts to secure the flywheel. Finally, it notes to check the flywheel runout after installation.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified torques and clearances. Precautions are provided such as cleaning and lubricating parts during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling various components of a 651B wheel scraper model, including:
1. The engine transfer gear and retarder, with steps to remove gears, bearings, and housing pieces.
2. The transmission transfer gear, with steps to remove gears, bearings, pumps, and the governor.
3. The transmission governor, with identification of parts and steps to disassemble and reassemble the governor valve bodies.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the assembly process. Torque specifications are provided for securing different fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, pressing bearings in at the proper angles and depths, and torquing bolts to the specified values.
This document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and compression brake valve assembly. The procedures include illustrations of the components and multi-step instructions for removal and installation, including proper torque specifications. Safety precautions are provided where necessary.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C15 or C18 engine. It describes removing components like the crankshaft rear seal, electric starting motor, and rear power take-off. It then explains how to use lifting tools to remove the flywheel housing and reinstall it, replacing seals and tightening bolts in a specific sequence and torque range. Similar instructions are provided for removing and installing just the rear power take-off components.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals.
4. Disassembling the scavenge pump by removing O-rings, bearings, shafts, and gears.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412C engines. The summary is:
1. The document outlines the required tools and safety procedures for removing the cylinder head, which involves detaching hoses, bolts, and lifting the heavy part off.
2. Instructions are provided for installing the new cylinder head gasket and reattaching the cylinder head using lifting brackets and torqueing the bolts in a specific sequence.
3. The lifter group removal process involves using a special tool to pull out the lifters and springs from the bores. Reinstallation requires aligning new springs and pressing the lifter assemblies back into place
The document provides instructions for disassembling and assembling a recoil spring assembly. Key steps include:
1. Using a specialized tooling bench to securely hold the recoil spring assembly, which is under several tons of force.
2. Carefully removing a nut to release the spring tension before disassembling the recoil spring components.
3. Reassembling the recoil spring components and using the tooling bench to apply controlled compression for assembly. Proper centering and leveling of the assembly is critical.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 657E wheel tractor. The removal procedure involves using various tools to disassemble the rear gear components and adapter assemblies. The installation procedure describes reassembling these components and requires pressing or installing bearings and seals using a driver group or press. Special care must be taken to keep parts clean and lubricated. The flywheel removal uses tools to secure the crankshaft gear and hoist the heavy flywheel off the engine.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using punch tools or pullers
The document provides instructions for installing the crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes heating the ring gear to 300°C before installing it on the flywheel. It also details installing guide bolts and lifting brackets to position the flywheel, applying grease to the bolt threads, and torquing the bolts to secure the flywheel. Finally, it notes to check the flywheel runout after installation.
This document provides step-by-step instructions for disassembling the pump control and pump housing of a 329DL excavator. It lists 60 steps to remove components like bolts, seals, pins, plates, barrels and shafts. Cleaning is important before disassembly to prevent dirt from entering mechanisms. The right pump control has a proportional reducing valve not present on the left. Tools are required to remove some components like bearings.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified torques and clearances. Precautions are provided such as cleaning and lubricating parts during assembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...8foskkdjdkdm3e
This document provides instructions for disassembling and assembling various components of a 651B wheel scraper model, including:
1. The engine transfer gear and retarder, with steps to remove gears, bearings, and housing pieces.
2. The transmission transfer gear, with steps to remove gears, bearings, pumps, and the governor.
3. The transmission governor, with identification of parts and steps to disassemble and reassemble the governor valve bodies.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F2 BACKHOE LOADER LYB
Configuration: 420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power
Train
Media Number -UENR5021-03 Publication Date -01/05/2015 Date Updated -05/06/2018
i06145783
Transmission (Direct Drive) - Disassemble
SMCS - 3030-015-DD; 3066-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 395-1590 Lifting Eye Assembly 2
B 422-5471 Lifting Eye Assembly 1
C 4C-3652 Spring Compressor 1
D 1P-1859 Retaining Ring Pliers 1
E 8H-0663 Bearing Puller Gp 1
F 8B-7551 Bearing Puller Gp 1
G 1U-6400 Three Jaw Puller 1
H 137-8102 Spring Compressor 1
Start By:
a. Remove the transmission.
1/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g03827943
1. Use two people to remove torque converter (1). The weight of torque converter (1) is
approximately 23 kg (51 lb). Remove torque converter (1) from transmission (2).
2. Remove bolt (4), the washer, and yoke (3) from transmission (2).
Illustration 2 g03828843
3. Remove shaft (5) from transmission (2).
4. Remove bolts (7) and gear shift (6) from transmission (2).
5. Remove bolts (10) and support assemblies (8) from transmission (2).
6. Remove bolt (11), the washer, and yoke (9) from transmission (2).
2/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g03828844
7. Remove bolts (13) and solenoid valve (12) from transmission (2).
Illustration 4 g03828845
Illustration 5 g03828846
Personal injury can result from being struck by parts propelled by a
released spring force.
3/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove head (14) from solenoid valve (12). Remove O-ring seal (15) from head (14).
9. Remove spring (16), carrier (17), spring (18), and piston (19) from solenoid valve (12).
Illustration 6 g03828847
Illustration 7 g03828848
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 10. Remove plug (20) from solenoid valve (12). Remove O-ring seal (21) from plug (20).
11. Remove spring (22) and poppet (23) from solenoid valve (12).
Illustration 8 g03828849
Illustration 9 g03828850
12. Remove self locking nut (24), O-ring seal (26) coil assembly (25), and O-ring seal (27) from
solenoid valve (12).
Illustration 10 g03828851
5/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g03828852
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove tube assembly (28) from solenoid valve (12). Remove O-ring seal (29) from tube
assembly (28).
14. Remove spring (30), push rod (31), washer (32), and spool (33) from solenoid valve (12).
Illustration 12 g03828876
15. Remove O-ring seals (34) from solenoid valve (12).
16. Repeat Step 8 through Step 14 for the opposite side of solenoid valve (12).
6/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g03828878
17. Attach Tooling (A) and a suitable lifting device to transmission (2). The weight of
transmission (2) is approximately 255 kg (562 lb). Place transmission (2) on a suitable work
bench. Secure transmission (2) to the suitable work bench.
18. Remove bolts (35) that secure the case.
Illustration 14 g03828879
19. Attach Tooling (A) and Tooling (B) to case (36). The weight of case (36) is approximately
45 kg (100 lb). Remove case (36) from the transmission.
Direct Drive, Front Output Shaft
7/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g03828880
1. Remove front output shaft (37).
Illustration 16 g03829476
Illustration 17 g03829477
2. Use suitable press to remove bearing cone (38).
3. Remove bearing cone (38), thrust washer (39), needle bearing (40), and gear (41) from the
shaft.
8/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 4. Remove roller bearing (42), spacer (43), roller bearing (44), needle bearing (45), and thrust
washer (46) from the shaft.
Illustration 18 g03829478
5. Remove retaining ring (47).
Illustration 19 g03829479
6. Remove plate (48).
Illustration 20 g03829480
9/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY C4...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g03829481
7. Remove friction disks (49) and friction clutches (50).
Illustration 22 g03829482
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Use a suitable press and Tooling (C) to compress spring assembly (52). Use Tooling (D) to
remove retaining ring (51).
10/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g03829483
9. Remove spring assembly (52) and retainer (53).
Illustration 24 g03829484
10. Release piston (54) by applying 207 kPa (30 psi) of air pressure into the lube passage as
indicated.
11. Remove seal ring (55).
Illustration 25 g03829485
11/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 12. Use Tooling (E) and a suitable press to remove bearing cone (56). Remove bearing cone
(56).
Direct Drive, Rear Output Shaft
Illustration 26 g03829593
Illustration 27 g03829664
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plug (57), spring (59), and ball (58).
12/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g03829665
Illustration 29 g03829668
2. Remove screws (60) from the shift forks. Remove rod (61) and ball (62).
Illustration 30 g03829669
Personal injury can result from being struck by parts propelled by a
released spring force.
13/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: Reinstalling plug (57) keeps the spring and the ball from being propelled from the
transmission case.
3. Reinstall plug (57) into the transmission case.
4. Remove rod (63) and shift forks (64).
Illustration 31 g03829670
Illustration 32 g03829671
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
14/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Remove plug (57), ball (67), and spring (66).
6. Remove rear output shaft (65).
Illustration 33 g03829672
Illustration 34 g03829763
7. Remove screw (69) and washer (68).
8. Use Tooling (F) and a suitable press to remove bearing cone (70) and gear (71).
15/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 35 g03829764
9. Remove needle bearings (72) and (73).
10. Use Tooling (D) to remove lock ring (74).
Illustration 36 g03829765
11. Remove synchronizer assembly (75).
Illustration 37 g03829811
12. Remove sleeve (76).
16/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
20. Illustration 41 g03829812
15. Use a suitable press to remove bearing cone (80) from the shaft. Remove bearing cone (80),
gear (89), gear (90).
16. Remove shims (81), synchronizer assembly (82), and shims (83).
17. Remove bearing (84), bearing spacer (85), and sleeve (86).
18. Remove sleeve (87), gear (88), bearing spacer (91), and bearing (92).
Direct Drive Shaft
Illustration 42 g03830710
1. Remove direct drive shaft (93).
18/33
420F2 Center Pivot Backhoe Loader LYB00001-UP (MACHINE) POWERED BY ...
2019/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...