1. The document provides step-by-step instructions for removing and disassembling the bank valve for a 420E Backhoe Loader.
2. It details 19 steps for removing the bank valve from the machine and 34 steps for disassembling the various components of the bank valve.
3. The bank valve controls hydraulic flow to implements like the backhoe and contains valves for functions like the boom, stick, bucket and swing. Proper removal and disassembly is required for maintenance or repair of the bank valve.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...fjsjekksemm
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. Detailed illustrations accompany each step to show how to properly disassemble the part. Safety precautions are provided to warn technicians of potential spring hazards. The overall process allows technicians to fully inspect and service individual parts of the bank valve.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...fujsjfkskemm
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. The procedure notes to take care handling fluids and releasing spring forces during disassembly.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...ufjjsjekkmdme
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. The process involves disconnecting hoses and wiring, and using tools to remove fasteners and components. Safety precautions are provided for releasing spring forces.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...fjsjfkskefmem
This document provides instructions for removing and disassembling the bank valve for a 420E backhoe loader. It involves removing various components like floor plates, ducts, and hoses to access the bank valve. To disassemble the bank valve, the inlet manifold and individual valves must be removed. O-rings, seals, springs, and other internal parts are then taken out of the valves. Precautions are given regarding releasing spring forces during disassembly.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...uudjfjjdkkksmm
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. The process involves disconnecting hoses and wiring, and using tools to remove fasteners and components. Safety precautions are provided for releasing spring forces.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove the components which include removing hoses, cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation which include lowering bearing temperatures, applying thread lock compound, positioning wear pads and bars/blocks, and reconnecting hoses. Special tools are required for removing and installing certain bearings.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...fjsjekksemm
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. Detailed illustrations accompany each step to show how to properly disassemble the part. Safety precautions are provided to warn technicians of potential spring hazards. The overall process allows technicians to fully inspect and service individual parts of the bank valve.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...fujsjfkskemm
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. The procedure notes to take care handling fluids and releasing spring forces during disassembly.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...ufjjsjekkmdme
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. The process involves disconnecting hoses and wiring, and using tools to remove fasteners and components. Safety precautions are provided for releasing spring forces.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...fjsjfkskefmem
This document provides instructions for removing and disassembling the bank valve for a 420E backhoe loader. It involves removing various components like floor plates, ducts, and hoses to access the bank valve. To disassemble the bank valve, the inlet manifold and individual valves must be removed. O-rings, seals, springs, and other internal parts are then taken out of the valves. Precautions are given regarding releasing spring forces during disassembly.
Caterpillar cat 420 e backhoe loader (prefix kmw) service repair manual (kmw0...uudjfjjdkkksmm
This document provides instructions for disassembling the bank valve of a 420E Backhoe Loader. It describes removing 34 components from the bank valve including manifolds, valves, seals, springs, and fittings. The process involves disconnecting hoses and wiring, and using tools to remove fasteners and components. Safety precautions are provided for releasing spring forces.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove the components which include removing hoses, cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation which include lowering bearing temperatures, applying thread lock compound, positioning wear pads and bars/blocks, and reconnecting hoses. Special tools are required for removing and installing certain bearings.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove components including cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation, which involves reinstalling components in reverse order and applying thread lock compound to bolts. Tools required include various pullers, lifting devices, drivers and thread lock compound.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low temperature are required for correctly installing the bearings.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove the components which include removing hoses, cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation which include lowering bearing temperatures, applying thread lock compound, positioning wear pads and bars/blocks, and reconnecting hoses. Special tools are required for removing and installing certain bearings.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove the components which include removing hoses, cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation which include lowering bearing temperatures, applying thread lock compound, positioning wear pads and bars/blocks, and reconnecting hoses. Special tools are required for removing and installing certain bearings.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...fjskefksemer
1) The document provides removal and installation instructions for sliding frames and bearings on a 434E backhoe loader.
2) It details removing components like cylinders, bars, blocks, and bearings using various tools.
3) Reinstallation involves lowering bearing temperatures and pressing them into place using a driver, and reinstalling other components in reverse order of removal. Proper seating of bearings is emphasized.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...ujdfjjkskkmmde
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...fujsefkksemm
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...fjjsefkksemme
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...ujfdjjkjskkemm
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
This document provides instructions for removing and disassembling the transmission of a 414E Backhoe Loader. It outlines 25 steps to remove the transmission from the machine and then disassemble it into major components. These components are then further disassembled by removing items like seals, gears, valve groups, and yoke assemblies. Tools required are also listed. The transmission removal and disassembly procedure is detailed with illustrations to identify specific parts.
The document is a service repair manual that provides instructions for removing the transmission from a 414E Backhoe Loader. It outlines 25 steps to disassemble the transmission into its major components. These include removing mounting hardware, draining fluids, disconnecting electrical connections and hydraulic lines, and using various tools to separate the transmission from the engine and remove internal shafts, gears, and casings. Precautions are given to support components and contain fluids during the process.
The document is a service repair manual that provides instructions for removing the transmission from a 414E Backhoe Loader. It outlines 25 steps to disassemble the transmission into its major components after removal from the vehicle. These include removing mounting components, draining fluids, disconnecting wiring harnesses and hydraulic lines, and using various tools to separate the transmission case from internal shafts, gears, and other parts. Precautions are given to support heavy components and contain fluids during the process.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E Backhoe Loader. The removal procedure involves 23 steps that remove components like cylinders, bars, blocks, and bearings. The installation procedure reverses the removal steps and involves preparing, positioning, and securing the various components using specific tools and torques. Personal safety warnings are also provided regarding hydraulic pressure and fluid containment.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E Backhoe Loader. The removal procedure involves 17 steps that remove components like cylinders, bars, blocks, and bearings. The installation procedure reverses the removal steps and involves applying thread lock compound and ensuring proper seating of bearings.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E Backhoe Loader. The removal procedure involves 17 steps that remove components like cylinders, bars, blocks, and bearings. The installation procedure reverses the removal steps and involves applying thread lock compound and ensuring proper seating of bearings.
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It describes in detail how to disassemble the 20 components of the pilot valve, including removing plates, springs, seals, spools and plugs. The assembly section then lists 21 steps to reassemble the pilot valve, replacing all O-rings and seals and ensuring correct installation of springs, spools and other components. The goal is to properly disassemble and reassemble the pilot valve while maintaining cleanliness to prevent issues.
This document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator equipped with a C6.4 engine. The removal procedure involves disconnecting harness and tubes, removing clips and bolts, and discarding old fuel lines. The installation procedure specifies installing new fuel lines and tubes using identification marks, torque specifications, and ensuring the fuel system is depressurized before opening it. Precautions are listed to prevent contamination and injury from high pressure fuel.
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator engine. The procedures describe removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed illustrations and cautions are provided to complete each step correctly and safely.
More Related Content
Similar to Caterpillar Cat 420E BACKHOE LOADER (Prefix KMW) Service Repair Manual (KMW00001 and up).pdf
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove components including cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation, which involves reinstalling components in reverse order and applying thread lock compound to bolts. Tools required include various pullers, lifting devices, drivers and thread lock compound.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low temperature are required for correctly installing the bearings.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove the components which include removing hoses, cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation which include lowering bearing temperatures, applying thread lock compound, positioning wear pads and bars/blocks, and reconnecting hoses. Special tools are required for removing and installing certain bearings.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. It outlines 23 steps to remove the components which include removing hoses, cylinders, bars, blocks, and bearings. It then outlines 17 steps for installation which include lowering bearing temperatures, applying thread lock compound, positioning wear pads and bars/blocks, and reconnecting hoses. Special tools are required for removing and installing certain bearings.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...fjskefksemer
1) The document provides removal and installation instructions for sliding frames and bearings on a 434E backhoe loader.
2) It details removing components like cylinders, bars, blocks, and bearings using various tools.
3) Reinstallation involves lowering bearing temperatures and pressing them into place using a driver, and reinstalling other components in reverse order of removal. Proper seating of bearings is emphasized.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...ujdfjjkskkmmde
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...fujsefkksemm
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...fjjsefkksemme
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
Caterpillar cat 434 e backhoe loader (prefix fsh) service repair manual (fsh0...ujfdjjkjskkemm
1) The document provides removal and installation instructions for the sliding frame and bearings of a 434E backhoe loader.
2) Over 20 steps are outlined to remove components like cylinders, bars, blocks, and bearings using various tools.
3) Similarly, over 20 steps are provided to install the same components in reverse order, ensuring proper positioning and torque of fasteners.
This document provides instructions for removing and disassembling the transmission of a 414E Backhoe Loader. It outlines 25 steps to remove the transmission from the machine and then disassemble it into major components. These components are then further disassembled by removing items like seals, gears, valve groups, and yoke assemblies. Tools required are also listed. The transmission removal and disassembly procedure is detailed with illustrations to identify specific parts.
The document is a service repair manual that provides instructions for removing the transmission from a 414E Backhoe Loader. It outlines 25 steps to disassemble the transmission into its major components. These include removing mounting hardware, draining fluids, disconnecting electrical connections and hydraulic lines, and using various tools to separate the transmission from the engine and remove internal shafts, gears, and casings. Precautions are given to support components and contain fluids during the process.
The document is a service repair manual that provides instructions for removing the transmission from a 414E Backhoe Loader. It outlines 25 steps to disassemble the transmission into its major components after removal from the vehicle. These include removing mounting components, draining fluids, disconnecting wiring harnesses and hydraulic lines, and using various tools to separate the transmission case from internal shafts, gears, and other parts. Precautions are given to support heavy components and contain fluids during the process.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E Backhoe Loader. The removal procedure involves 23 steps that remove components like cylinders, bars, blocks, and bearings. The installation procedure reverses the removal steps and involves preparing, positioning, and securing the various components using specific tools and torques. Personal safety warnings are also provided regarding hydraulic pressure and fluid containment.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E Backhoe Loader. The removal procedure involves 17 steps that remove components like cylinders, bars, blocks, and bearings. The installation procedure reverses the removal steps and involves applying thread lock compound and ensuring proper seating of bearings.
The document provides instructions for removing and installing the sliding frame and bearings on a 434E Backhoe Loader. The removal procedure involves 17 steps that remove components like cylinders, bars, blocks, and bearings. The installation procedure reverses the removal steps and involves applying thread lock compound and ensuring proper seating of bearings.
Similar to Caterpillar Cat 420E BACKHOE LOADER (Prefix KMW) Service Repair Manual (KMW00001 and up).pdf (18)
This document provides instructions for removing and installing various components of the heating and air conditioning system for a Caterpillar 321C excavator, including:
- The heating and air conditioning unit
- The blower motor
- The refrigerant receiver-dryer
- The actuator motor for the floor vent, front and rear vents
It includes detailed illustrations and numbered steps for each procedure, and safety warnings regarding working with refrigerants.
The document provides instructions for disassembling and assembling the pilot valve (joystick) of a 322C excavator. It describes in detail how to disassemble the 20 components of the pilot valve, including removing plates, springs, seals, spools and plugs. The assembly section then lists 21 steps to reassemble the pilot valve, replacing all O-rings and seals and ensuring correct installation of springs, spools and other components. The goal is to properly disassemble and reassemble the pilot valve while maintaining cleanliness to prevent issues.
This document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator equipped with a C6.4 engine. The removal procedure involves disconnecting harness and tubes, removing clips and bolts, and discarding old fuel lines. The installation procedure specifies installing new fuel lines and tubes using identification marks, torque specifications, and ensuring the fuel system is depressurized before opening it. Precautions are listed to prevent contamination and injury from high pressure fuel.
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator engine. The procedures describe removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed illustrations and cautions are provided to complete each step correctly and safely.
This document provides removal and installation instructions for various components of an excavator air conditioning system. It includes:
1) Detailed step-by-step instructions to remove components like the air conditioner group, actuator motors, control module, and refrigerant receiver-dryer. Each step includes illustrations.
2) Safety warnings to take precautions when working with refrigerant due to the risk of injury from contact or inhalation.
3) Specifications for replacement parts like seals and dimensions for proper installation.
The document provides thorough maintenance instructions for servicing excavator air conditioning systems.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive before removing certain components.
1. The document provides instructions for removing and installing fuel injection lines and the fuel manifold on a Caterpillar 321D LCR excavator.
2. To remove the lines and manifold, technicians must disconnect harness assemblies, tubes, and hoses after relieving fuel pressure and marking components.
3. Installation requires connecting new fuel lines and hoses according to illustrated steps while maintaining cleanliness to prevent contamination.
1. The document provides instructions for removing and installing an electronic unit injector, turbocharger, and exhaust manifold on a Caterpillar 321D LCR excavator. It includes diagrams and lists required tools.
2. The procedure for removing an electronic unit injector involves disconnecting harness assemblies and fuel lines, removing mounting bolts and nuts, and using pry bars. Cleanliness is important to prevent dirt entry.
3. Removing the turbocharger requires loosening clamps and removing nuts, tubes, and hoses connecting it to the engine.
4. Removing the exhaust manifold is preceded by removing the turbocharger. Cleanliness of all parts is emphasized during removal and installation.
This document provides instructions for removing and installing the fuel injection pump gear on a Caterpillar C6.4 engine. It describes:
- Using a puller tool to remove the existing gear and key
- Installing the key and securing the new gear with a torque wrench, holding it in a soft jaw vice
- Cleanliness is important to prevent contaminants from causing premature wear
Caterpillar Cat 320C U Excavator (Prefix PAC) Service Repair Manual (PAC00001...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
1) Removing and installing the flywheel housing.
2) Removing and installing the crankshaft pulley.
3) Removing the crankshaft front seal.
4) Installing a new crankshaft front seal.
5) Removing just the idler gear from the front gear group.
The document contains detailed steps, illustrations, and safety notices for completing each procedure. Required tools are listed for each job.
The document provides instructions for removing and installing an engine oil filter base and engine oil cooler on a Caterpillar 3064 or 3066 engine. The instructions include removing bolts and filters, checking seals and gaskets, and ensuring parts are clean to prevent contamination. Tools and safety precautions are also listed.
Caterpillar Cat 320C S Excavator (Prefix BBL) Service Repair Manual (BBL00001...fujsked9dikdkd
The document provides installation instructions for auxiliary control valves on an excavator model 320C. It involves 33 steps including installing hoses and fittings, connecting electrical connectors, and tightening bolts. Special tools and safety precautions are noted. The process concludes by installing covers and checking operation.
The document provides instructions for disassembling a swing drive from a 320C excavator. It describes:
1) Removing the retaining ring from the swing drive housing using retaining ring pliers.
2) Using a driver group to remove the bearing from the housing.
3) Removing the inner ring, roller assembly, and outer ring from the bearing.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
Caterpillar Cat 320C LU 320CLU Excavator (Prefix PAC) Service Repair Manual (...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
1) Removing and installing the flywheel housing.
2) Removing and installing the crankshaft pulley.
3) Removing the crankshaft front seal.
4) Installing a new crankshaft front seal.
5) Removing just the idler gear from the front gear group.
The document contains detailed steps, illustrations, and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar Cat 320C L Excavator (Prefix BBL) Service Repair Manual (BBL00001...fujsked9dikdkd
The document provides instructions for installing and assembling auxiliary control valves on an excavator model 320C. It describes 38 steps for installing control valves F1 and F4, including connecting hoses and electrical connections, installing mounting bolts, and filling hydraulic oil. It also describes 12 steps for assembling the F2 auxiliary control valve, including installing O-rings, springs, fittings and plugs on the spool, solenoid valve and housing. The instructions conclude by stating to install the F2 control valve by referring to an installation procedure.
Caterpillar Cat 320C L 320CL Excavator (Prefix SBN) Service Repair Manual (SB...fujsked9dikdkd
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 320C excavator engine. The removal procedure involves using tools to remove the electric starting motor and flywheel/ring gear. Twelve bolts and washers are then removed to detach the adapter from the flywheel housing. For installation, the adapter is reattached with twelve bolts and washers, followed by reinstalling the flywheel/ring gear and electric starting motor.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...fujsked9dikdkd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools to secure and lift it.
- Removing the crankshaft rear seal using a slide hammer puller and distorter ring.
- Installing a new crankshaft rear seal and wear sleeve using an installer, locator, and bolt.
- Removing and installing the flywheel housing which requires lifting equipment and replacing the oil seal if needed.
- Removing the crankshaft pulley using a combination puller and socket.
Caterpillar Cat 320C L 320CL Excavator (Prefix HKT) Service Repair Manual (HK...fujsked9dikdkd
This document provides installation instructions for auxiliary control valves on an excavator model 320C. It involves installing pilot lines and hoses between the auxiliary control valves and connecting them to the main control valve and hydraulic system. The steps include fastening the control valves together, installing mount bolts, connecting pilot lines and hoses, and checking for proper operation and leaks once installation is complete. Proper containment of fluids and cleaning of components is emphasized to prevent contamination of the hydraulic system.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...fujsked9dikdkd
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles.
2. Using puller tools attached to the nozzle and fuel line connection to carefully extract each nozzle.
3. Cleaning all parts to prevent contamination, then reversing the removal steps to reinstall the nozzles, fuel lines, and other components. Proper cleaning and replacement of parts is emphasized to avoid damaging components and contaminating the fuel system.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
3. Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
1. Lower all implements to the ground.
2. Release the pressure in the hydraulic system. Refer to Disassembly and Assembly,
"Hydraulic System Pressure - Release".
3. Drain the hydraulic oil into a suitable container for storage or disposal. Refer to Operation
and Maintenance Manual, "Hydraulic System Oil - Change".
Illustration 1 g01119509
4. Remove bolts (3) and plate (2). Repeat for the other side. Remove floor mat (1).
Illustration 2 g01121317
5. Remove bolts (4) and floorplate (5).
2/7
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01121182
6. Remove louver (6).
Illustration 4 g01121187
7. Remove bolt (7).
Illustration 5 g01121221
8. Remove bolt (9) and duct (8).
9. Repeat Steps 6 through 8 for the other side.
3/7
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g01121318
10. Remove bolts (10) from each side and remove floorplate (11).
Illustration 7 g01121322
11. Remove bolts (12) from each side of bar (13) and remove bar (13).
Illustration 8 g01121327
12. Disconnect seven harness assemblies (14).
4/7
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01121334
13. Disconnect four hose assemblies (15). Disconnect eight hose assemblies (16). Remove clip
(17).
Illustration 10 g01121339
14. Remove bolts (18) and place block assembly (19) to the side.
Illustration 11 g01121356
15. Disconnect hose assembly (20) from each side of the bank valve for the backhoe.
5/7
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g01121411
19. Attach Tooling (A) and a suitable lifting device to bank valve (30) for the backhoe. The
weight of bank valve (30) for the backhoe is approximately 80 kg (175 lb). Remove bolts
(29) and remove bank valve (30) for the backhoe.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 21:15:57 UTC+0800 2019
7/7
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER KMW
Configuration: 420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders
Machine Systems
Media Number -RENR6485-08 Publication Date -01/01/2013 Date Updated -24/01/2013
i03895571
Bank Valve (Backhoe) - Disassemble
SMCS - 5051-015; 5476-015
S/N - BXE1-UP
S/N - DDT1-UP
S/N - EAT1-UP
S/N - FSH1-UP
S/N - GKZ1-UP
S/N - HLS1-UP
S/N - KMW1-UP
S/N - LBE1-UP
S/N - MFG1-6000
Disassembly Procedure
Start By:
A. Remove the bank valve (backhoe). Refer to Disassembly and Assembly, "Bank Valve
(Backhoe) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01401051
1. The valves within the bank valve are positioned in the following manner: Inlet manifold
(1) , right hand stabilizer valve (2) , boom valve (3) , right hand stick valve (4) , swing valve
(5) , bucket valve (6) , extendable stick valve (7) , left hand stabilizer valve (8) , and outlet
manifold (9) .
Illustration 2 g01401145
2. Remove nuts (11) from bank valve (10) . Remove inlet manifold (1) .
2/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g01403300
3. Disassemble inlet manifold (1) .
Illustration 4 g01401147
4. Remove plugs (12) and (14) . Remove O-ring seal (13) and (15) .
3/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 5 g02139374
5. Remove the plug and use an allen wrench to remove screen (15a) from inlet manifold (1) .
Illustration 6 g01401342
6. Remove plug (16) . Remove O-ring seal (17) . Remove nut (18) . Remove coil (19) .
4/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 7 g01401363
7. Remove spool (20) . Remove cartridge (21) .
Illustration 8 g01401393
8. Remove backup ring (22) , O-ring seal (23) and O-ring (24) from cartridge (21) .
Illustration 9 g01401420
9. Remove right hand stabilizer valve (2) .
5/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 10 g01401440
10. Remove O-ring seals (25) from right hand stabilizer valve (2) .
Illustration 11 g01401450
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
11. Remove bolts (26) and cover (27) .
6/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 12 g01401468
12. Remove spool (28) , retainer (29) , spring (30) , and O-ring seal (31) .
Illustration 13 g01401486
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove bolts (33) and cover (32) . Remove check valve (34) .
7/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 17 g01401656
16. Remove O-ring seals (41) . Remove check valve (39) . Remove O-ring seal (40) .
Illustration 18 g01401667
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
17. Remove bolts (42) . Remove cover (43) .
9/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) POWE...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 19 g01401683
18. Remove spool (44) , retainer (45) , spring (46) , and O-ring seal (47) .
Illustration 20 g01401691
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove bolts (48) . Remove cover (49) .
10/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) PO...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 21 g01401712
20. Remove O-ring seal (50) , spring (51) , and retainer (52) .
Illustration 22 g01401777
21. Remove plug (53) . Remove fittings (54) .
Illustration 23 g01401792
22. Remove O-ring seal (55) and orifice valve (56) .
11/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) PO...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 26 g01401859
25. Remove right hand stick valve (4) .
26. Repeat Steps 16 through Step 24 for the disassembly of right hand stick valve (4) .
Illustration 27 g01401876
27. Remove swing valve (5) .
28. Repeat Steps 16 through Step 24 for the disassembly of swing valve (5) .
Illustration 28 g01401886
29. Remove bucket valve (6) .
30. Repeat Steps 16 through Step 24 for the disassembly of bucket valve (6) .
13/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) PO...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 32 g01402072
34. Remove O-ring seals (64) and (66) . Remove backup ring (65) .
Illustration 33 g01402093
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
35. Remove relief valve (67) . Remove bolts (68) and remove cover (69) .
15/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) PO...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 34 g01402110
36. Remove spool (70) , retainer (71) , spring (72) , and O-ring seal (73) .
Illustration 35 g01402115
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
37. Remove bolts (74) . Remove cover (75) .
16/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) PO...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 36 g01402129
38. Remove O-ring seal (76) , spring (77) , and retainer (78) .
Illustration 37 g01402133
39. Remove plug (79) .
Illustration 38 g01402154
40. Remove O-ring seal (80) and orifice valve (81) .
17/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) PO...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 39 g01402544
41. Remove stabilizer valve (8) .
42. Repeat Steps 10 through Step 14 for the disassembly of stabilizer valve (8) .
Illustration 40 g01402845
43. Disassemble outlet manifold (9) .
18/21
420E Backhoe Loader Parallel Lift Center Pivot KMW00001-UP (MACHINE) PO...
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...