This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves over 40 steps to fully disassemble the travel motor by removing components like the head, relief valves, pistons, plates, seals, bearings, and housing. The assembly process is described in reverse order and emphasizes cleanliness, application of oil, and ensuring alignment marks match during reinstallation of parts.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists over 30 detailed steps for removing components like the ring gear, carrier assemblies, gears, shafts and seals. Bearing preload is determined by applying specific pressures and measuring clearances with a micrometer. All components must be thoroughly cleaned before precise reassembly in their original locations using torque wrenches and lifting devices, with seals and threaded surfaces coated in locking compound or adhesive.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjkskedmme
The document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. It describes 17 steps to disassemble the final drive, including removing the final drive cover, ring gear, sun gears, carrier assemblies, planetary gears and shafts. Tools required include a transmission repair stand, link brackets, hydraulic wrench, hex bit socket and forcing bolts. Marks must be made to indicate original part locations for reassembly.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists over 30 detailed steps for removing components like the ring gear, carrier assemblies, gears, shafts and seals. Bearing preload is determined by applying specific pressures and measuring clearances with a micrometer. All components must be thoroughly cleaned before precise reassembly in their original locations using torque wrenches and lifting devices, with seals and threaded surfaces coated in locking compound or adhesive.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjkskedmme
The document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. It describes 17 steps to disassemble the final drive, including removing the final drive cover, ring gear, sun gears, carrier assemblies, planetary gears and shafts. Tools required include a transmission repair stand, link brackets, hydraulic wrench, hex bit socket and forcing bolts. Marks must be made to indicate original part locations for reassembly.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, plates and shafts. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing springs and seals. Tools required for specific steps are also listed.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 390 f l excavator (prefix hjd) service repair manual (hjd0000...fujskekfmsme
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and a driver group. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 315 b fm l excavator (prefix 7rz) service repair manual (7rz0...fjsekdmmeed
The document provides instructions for disassembling and assembling track rollers on a 315B excavator. It describes:
1) Removing the track rollers and draining oil from the roller before disassembly.
2) Using presses and tools to remove internal components like seals, shafts, and bearings.
3) Checking shaft end play and installing new internal components in reverse order.
4) Filling the roller with the specified oil and reinstalling it along with the track guide.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 324 e l excavator (prefix ldg) service repair manual (ldg0000...fjsekkdmme
This document provides instructions for disassembling and assembling the travel motor on 324E L and 324E LN Excavator models. The disassembly process involves removing 28 components from the travel motor including the head, springs, plates, seals, bearings and more. The assembly process is the reverse and includes lubricating components and using various tools to install components in the proper order and orientation. Precautions are provided to avoid damaging parts and ensure proper assembly.
Caterpillar cat 390 f l excavator (prefix tye) service repair manual (tye0000...fujskekfmsme
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It lists 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then lists 12 steps for reassembly, starting with installing a lip seal and finishing by reinstalling covers. Precautions are provided regarding cleaning parts and applying oil before assembly.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
This document provides instructions for removing and installing the crankshaft rear seal on Caterpillar 3054 engines. It describes the process for both engines with a 14-bolt housing assembly and those with a 10-bolt housing assembly. The removal procedure involves removing the flywheel first, then bolts and housing to access the seal. Installation requires cleaning surfaces, pressing the new seal into the housing, lubricating and aligning parts, then reinstalling bolts and housing. Tools including a rear seal installer and alignment tool are required.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, barrel assembly and more. The assembly process reverses the disassembly with 33 steps and notes to clean parts, apply oil, and reinstall components in their original locations and orientations. Precautions are provided to contain fluids, wear protective equipment for spring loaded parts, and maintain cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...paws21610697
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, and bearings. The assembly process reverses the disassembly with 33 steps, including pressing in bearings, installing seals and springs, and reassembling subassemblies in their original locations. Precautions are provided to contain fluids, handle spring-loaded parts carefully, and ensure cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual Instant D...jiuliu14811471
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, barrel assembly and more. The assembly process reverses the disassembly with 33 steps and notes to clean parts, apply oil, and reinstall components in their original locations and orientations. Precautions are provided to contain fluids, wear protective equipment for spring loaded parts, and maintain cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual Instant D...qianxu35543635
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, and bearings. The assembly process reverses the disassembly with 33 steps, including pressing in bearings, installing seals and springs, and reassembling subassemblies in their original locations. Precautions are provided to contain fluids, handle spring-loaded components carefully, and ensure cleanliness during the process.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, plates and shafts. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing springs and seals. Tools required for specific steps are also listed.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 390 f l excavator (prefix hjd) service repair manual (hjd0000...fujskekfmsme
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and a driver group. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 315 b fm l excavator (prefix 7rz) service repair manual (7rz0...fjsekdmmeed
The document provides instructions for disassembling and assembling track rollers on a 315B excavator. It describes:
1) Removing the track rollers and draining oil from the roller before disassembly.
2) Using presses and tools to remove internal components like seals, shafts, and bearings.
3) Checking shaft end play and installing new internal components in reverse order.
4) Filling the roller with the specified oil and reinstalling it along with the track guide.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 324 e l excavator (prefix ldg) service repair manual (ldg0000...fjsekkdmme
This document provides instructions for disassembling and assembling the travel motor on 324E L and 324E LN Excavator models. The disassembly process involves removing 28 components from the travel motor including the head, springs, plates, seals, bearings and more. The assembly process is the reverse and includes lubricating components and using various tools to install components in the proper order and orientation. Precautions are provided to avoid damaging parts and ensure proper assembly.
Caterpillar cat 390 f l excavator (prefix tye) service repair manual (tye0000...fujskekfmsme
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It lists 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then lists 12 steps for reassembly, starting with installing a lip seal and finishing by reinstalling covers. Precautions are provided regarding cleaning parts and applying oil before assembly.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 120 g motor grader (prefix 11w) service repair manual (11w010...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 120G motor grader, including the cylinder head, spacer plate, and water directors. The removal and installation procedures describe removing bolts and other fasteners, lifting components, cleaning surfaces, applying sealants, and torquing bolts to specified values. Safety notices are included to handle fluids properly and avoid contaminating parts.
This document provides instructions for removing and installing the crankshaft rear seal on Caterpillar 3054 engines. It describes the process for both engines with a 14-bolt housing assembly and those with a 10-bolt housing assembly. The removal procedure involves removing the flywheel first, then bolts and housing to access the seal. Installation requires cleaning surfaces, pressing the new seal into the housing, lubricating and aligning parts, then reinstalling bolts and housing. Tools including a rear seal installer and alignment tool are required.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, barrel assembly and more. The assembly process reverses the disassembly with 33 steps and notes to clean parts, apply oil, and reinstall components in their original locations and orientations. Precautions are provided to contain fluids, wear protective equipment for spring loaded parts, and maintain cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...paws21610697
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, and bearings. The assembly process reverses the disassembly with 33 steps, including pressing in bearings, installing seals and springs, and reassembling subassemblies in their original locations. Precautions are provided to contain fluids, handle spring-loaded parts carefully, and ensure cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual Instant D...jiuliu14811471
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, barrel assembly and more. The assembly process reverses the disassembly with 33 steps and notes to clean parts, apply oil, and reinstall components in their original locations and orientations. Precautions are provided to contain fluids, wear protective equipment for spring loaded parts, and maintain cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual Instant D...qianxu35543635
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, and bearings. The assembly process reverses the disassembly with 33 steps, including pressing in bearings, installing seals and springs, and reassembling subassemblies in their original locations. Precautions are provided to contain fluids, handle spring-loaded components carefully, and ensure cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, and bearings. The assembly process reverses the disassembly with 31 steps, applying lubricant and ensuring parts are cleaned and replaced as needed. Precautions are provided to contain fluids, release spring forces carefully, and maintain part alignments through the process.
Caterpillar cat 390 f l excavator (prefix tye) service repair manual (tye0000...ifkkdmdmdm
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, and bearings. The assembly process reverses the disassembly with 33 steps, including pressing in bearings, installing seals and springs, and reassembling subassemblies in their original locations. Precautions are provided to contain fluids, handle spring-loaded components carefully, and ensure cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...f8uuseijdkmd3e
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. The disassembly process involves 40 steps to remove components like the head, relief valves, springs, seals, piston, barrel assembly and more. The assembly process reverses the disassembly with 33 steps, ensuring proper installation of components and use of alignment marks and tools. Cleanliness is emphasized throughout to prevent damage to precision parts.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...jdjkskmikdkmd
The document provides instructions to disassemble and assemble the travel motor of a 390F L Excavator. It lists 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, springs, seals, pistons, plates, and shaft. It then lists 17 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...paws21610697
The document provides instructions to disassemble and assemble the travel motor of a 390F L Excavator. It lists 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, springs, seals, pistons, plates, and shaft. It then lists 17 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual Instant D...jiuliu14811471
The document provides instructions to disassemble and assemble the travel motor of a 390F L Excavator. It lists 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, springs, seals, piston, plates, and shaft. It then lists 17 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual Instant D...qianxu35543635
The document provides instructions to disassemble and assemble the travel motor of a 390F L Excavator. It lists 40 steps to disassemble the travel motor by removing components like the head, relief valves, springs, seals, pistons, plates, and shaft. It then lists 17 steps to assemble the travel motor by reinstalling these components in the reverse order, ensuring alignment marks match and springs are installed properly to avoid injury. Precautions are provided to contain fluids, wear protective equipment, and maintain cleanliness during the process.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...f7djidksmd3e
The document provides instructions to disassemble and assemble the travel motor of a 390F L Excavator. It lists 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, springs, seals, piston, plates, and shaft. It then lists 17 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 390 f l excavator (prefix mgf) service repair manual (mgf0000...fujskekfmsme
The document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It lists 40 steps for disassembly, including removing components like the head, relief valves, springs, seals, piston, and bearings. It then lists 17 steps for assembly, installing these components in reverse order and noting that cleanliness and applying oil to parts is important. Tools required are also listed.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...f8uuseijdkmd3e
The document provides instructions to disassemble and assemble the travel motor of a 390F L Excavator. It lists 40 steps to disassemble the travel motor by removing components like the head, relief valves, springs, seals, pistons, plates, and shaft. It then lists 17 steps to assemble the travel motor by reinstalling these components in the reverse order, ensuring alignment marks match and springs are installed properly to avoid injury. Precautions are provided to contain fluids, wear protective equipment, and maintain cleanliness during the process.
Caterpillar cat 390 f l excavator (prefix mgf) service repair manual (mgf0000...ifkkdmdmdm
The document provides instructions to disassemble and assemble the travel motor of a 390F L Excavator. It lists 40 steps to disassemble the travel motor by removing components like the head, relief valves, springs, seals, pistons, plates, and shaft. It then lists 16 steps to assemble the travel motor by reinstalling these components in the reverse order. Precision cleaning and alignment marks are emphasized to ensure correct reassembly.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...fujskemdidk8u
This document provides instructions to disassemble a 390F L excavator travel motor. It lists 40 steps to remove components like the head, relief valves, pistons, springs, seals, plates, and shaft. Precision tools are required to remove parts and release spring forces. Components must be kept in order and reinstalled in their original locations and orientations.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...tingrm81805
The document provides disassembly instructions for a 390F L excavator travel motor in 40 steps. It details removing components such as the motor head, relief valves, pistons, springs, seals, plates, and bearings. Tools required include link brackets, a slide hammer puller, threaded rods, pliers, and drivers. Safety notices are provided to contain fluids and brace against spring forces during disassembly.
Caterpillar Cat 390F L Excavator (Prefix HSM) Service Repair Manual (HSM00001...nkog14651119
The document provides disassembly instructions for a travel motor in 40 steps. It instructs the technician to remove components like the head, relief valves, spools, pistons, springs, seals, bearings, and housing plates. Precise alignment marks and special tools are required to disassemble precision components while containing fluids and avoiding injury from spring forces.
Similar to Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 and up) (20)
Caterpillar cat 320 d rr excavator (prefix fxk) service repair manual (fxk000...9fiseookddk
The document provides instructions for removing and installing the crankshaft on Caterpillar 3064 and 3066 engines. It describes removing components like the front housing, oil pan, flywheel housing and connecting rod caps. It then explains how to remove the crankshaft main bearings and thrust washers. For installation, it details lubricating the crankshaft and bearings before lowering the crankshaft into place and securing the main bearing caps with bolts torqued to the specified value. End play is then checked using a dial indicator to ensure it is within the acceptable range.
Caterpillar cat 320 d rr excavator (prefix eby) service repair manual (eby000...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...9fiseookddk
The document provides instructions for removing and installing valve guides and valve seat inserts from the cylinder head of a Caterpillar 320D LRR excavator engine. It describes:
1) Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2) Using various tools to remove the old valve guides and seat inserts and clean the cylinder head.
3) Lubricating and installing new valve guides so they protrude a specified amount from the cylinder head.
4) Lowering the temperature of new seat inserts and installing them using the appropriate tools.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...9fiseookddk
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar cat 320 d lrr excavator (prefix gkl) service repair manual (gkl00...9fiseookddk
The document provides instructions for checking bearing clearances on excavator engines. It describes the required plastic gauge tools and notes that Cat does not recommend checking actual clearances due to the risk of damage or inaccurate results. It provides instructions for using the plastic gauges to check clearances between main and connecting rod bearings and respective journals if a technician chooses to perform the checks. Safety precautions are outlined such as ensuring clean, dry surfaces and avoiding the use of materials that could damage bearing surfaces.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...9fiseookddk
The document provides instructions for removing and installing the crankshaft on Caterpillar 3064 and 3066 engines. It describes removing components like the front housing, oil pan, flywheel housing and connecting rod caps. It then explains how to remove the crankshaft main bearings and thrust washers. For installation, it details lubricating the crankshaft and bearings and installing the main bearing caps, thrust washers and connecting rod caps, checking end play with a dial indicator.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar cat 319 d ln excavator (prefix zca) service repair manual (zca000...9fiseookddk
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 38 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is critical throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d ln excavator (prefix rjp) service repair manual (rjp000...9fiseookddk
The document provides instructions for disassembling and assembling the final drive of a 319D L and 319D LN excavator. Some key steps include:
- Removing the final drive cover, carrier assembly, ring gears, and other components.
- Disassembling the carrier assembly by removing planetary shafts, gears, bearings, and other internal parts.
- Separating the main housing from the motor housing after removing bolts and gears.
- Cleaning all parts thoroughly before assembly and replacing all O-rings, gaskets, and seals.
- Assembling involves installing bearings, gears, carrier assembly, ring gears, cover, and other components in reverse order of dis
Caterpillar cat 319 d ln excavator (prefix kfm) service repair manual (kfm000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 31 parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs to install 33 parts in reverse order and provides notes on cleaning, lubricating, and setting bearing preload using shims.
Caterpillar cat 319 d ln excavator (prefix fmh) service repair manual (fmh000...9fiseookddk
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with removing the travel motor and cleaning it. Then it describes dismantling the various components like the head, barrel assembly, piston guide, and brake piston. Precise steps are given to disassemble seals, plates, and other parts. The assembly section reverses the process and provides details on installing components in the correct order and orientation while applying lubricants. Proper tool use and safety precautions are emphasized throughout.
Caterpillar cat 319 d ln excavator (prefix eaw) service repair manual (eaw000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. It describes in detail how to disassemble the final drive components including removing the cover, carrier assembly, planetary gears, ring gears, and other parts. It then describes the assembly process and lists the required tools, noting that cleanliness and replacing all seals and gaskets is important.
Caterpillar cat 319 d ln excavator (prefix ayf) service repair manual (ayf000...9fiseookddk
This document provides instructions for disassembling and assembling the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing over 30 individual parts from the final drive assembly using various tools. The assembly procedure instructs to clean all parts thoroughly and replace all O-rings, gaskets and seals before reassembling the final drive in the reverse order of disassembly while applying lubricants to components as needed. Proper cleaning, part replacement, and lubrication are emphasized to ensure correct reassembly.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...9fiseookddk
This document provides assembly instructions for a final drive on an excavator model 319D L. The steps include:
1. Installing the final drive sprocket and bearings
2. Assembling the two carrier assemblies by installing planetary gears, shafts, and pins
3. Installing the assembled carriers, sun gears, and spacer rings
4. Attaching the ring gears and installing the main housing cover
5. Torquing plugs on the cover and completing the final drive assembly
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...9fiseookddk
The document provides instructions for disassembling and assembling the final drive of a 319D L and 319D LN excavator. Some key steps include:
- Removing the final drive cover, carrier assembly, ring gears, and other components.
- Disassembling the carrier assembly by removing planetary shafts, gears, bearings, and other internal parts.
- Separating the main housing from the motor housing after removing bolts and gears.
- Cleaning all parts thoroughly before assembly and replacing all O-rings, gaskets, and seals.
- Assembling involves installing bearings, gears, carrier assembly, ring gears, cover, and other components in reverse order of dis
Caterpillar cat 319 d l excavator (prefix krm) service repair manual (krm0000...9fiseookddk
This document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It describes 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It also describes 31 steps for reassembling these components, including pressing in bearings, determining shim thickness, and installing seals using a special tool. Proper cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...9fiseookddk
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...9fiseookddk
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with removing the travel motor and cleaning it. Then it describes dismantling the various components like the head, barrel assembly, piston guide, and brake piston. Precise steps are given to disassemble seals, plates, and other parts. The assembly section reverses the process and provides details on installing components in the correct order and orientation while applying lubricants. Proper tool use and safety precautions are emphasized throughout.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 390F EXCAVATOR FEH
Configuration: 390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
390F Excavator Machine Systems
Media Number -UENR0165-05 Publication Date -01/01/2018 Date Updated -24/01/2018
i05680270
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0074 Slide Hammer Puller Gp 1
C 123-4370 Threaded Rod M20 - 2.5 2
D 1P-1864 Pliers 1
E 1P-1858 Pliers 1
F 1P-0520 Driver Group 1
G 8T-0349 Bolt 2
Start By:
a. Remove the travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1. Place an alignment mark across all housings of the travel motor for assembly purposes.
Illustration 1 g01282832
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. Remove two socket head bolts (2) from head (1) that are 180 degrees from each other.
Replace these two bolts with Tooling (G). Tooling (G) will retain the brake cover when the
remaining socket head bolts (2) are removed.
3. Carefully remove the remaining socket head bolts (2) that retain head (1) in position.
Remove socket head bolts (2) evenly, in a crisscross pattern.
4. Remove Tooling (G) from head (1).
2/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01283040
5. Install Tooling (A) and a suitable lifting device to head (1).
6. Remove head (1) from the travel motor. The weight of head (1) is approximately 68 kg
(150 lb).
Illustration 3 g01283045
7. Remove relief valve (3).
Illustration 4 g01283049
3/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove cap (4) from body (9). Remove piston (5), spring (6), spool (7), and spring (8) from
body (9).
9. Remove O-ring seals (10), (12), and (14). Remove backup rings (11) and (13).
10. Remove the other relief valve from the other side of the head.
11. Repeat Steps 8 and 9 for the disassembly of the other relief valve.
Illustration 5 g01283057
12. Remove plug (15).
Illustration 6 g01283060
4/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 13. Remove spool (16).
Illustration 7 g01283070
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove plug (17).
Illustration 8 g01283075
15. Remove spool (21) from the head. Remove O-ring seal (22) from plug (17).
16. Remove plug (18) from the other side of the head. Remove spring (20). Remove O-ring seal
(19) from plug (18).
5/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g01283083
17. Remove cap (23) and pressure reducing valve (24).
Illustration 10 g01283088
18. Remove O-ring seals (25), (26), and (27) from pressure reducing valve (24).
Illustration 11 g01283096
19. Use Tooling (B) in order to remove bearing (28) from the head.
6/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01283101
20. Remove port plate (29) from the travel motor.
Note: Note the location of springs (30) before removal.
21. Remove springs (30) from the travel motor.
22. Remove O-ring seals (31).
Illustration 13 g01283110
23. Place alignment marks on piston (32) and the housing. The dowel hole in piston (32) must
be reinstalled to the original location.
7/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g01283120
24. Install Tooling (C) to the threaded holes in piston (32). Install Tooling (A) and a suitable
lifting device on Tooling (C), as shown. Remove piston (32) from the travel motor.
Illustration 15 g01283129
25. Remove O-ring seals (33) and (34) from the travel motor.
Illustration 16 g01283133
26. Remove separator plates (35) and friction plates (36) from the travel motor.
Illustration 17 g01283138
8/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01283139
Note: Barrel assembly (37), piston assemblies (39), and retainer (40) must remain intact
during removal.
27. Position the travel motor sideways. Carefully remove barrel assembly (37) from shaft (38).
Illustration 19 g01283155
28. Place identification marks on piston assemblies (39), retainer (40), and barrel assembly (37).
These components must be reinstalled in the original location.
29. Remove retainer (40) and piston assemblies (39) from barrel assembly (37).
9/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g01283175
Illustration 21 g01283193
30. Remove guide (41).
31. Remove springs (42).
Illustration 22 g01283187
32. Turn swashplate (43) counterclockwise in order to provide clearance for the removal of
swashplate (43).
33. Remove swashplate (43) from the travel motor housing.
10/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M007...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g01283195
34. Remove piston (44) and pivots (45).
Illustration 24 g01283206
35. Use Tooling (D) in order to remove retaining ring (46) from shaft (38).
Illustration 25 g01283209
36. Use a soft hammer in order to drive shaft (38) and bearing (47) from the motor housing.
11/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M007...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g01283212
37. Use Tooling (E) in order to remove retaining ring (48) from bearing (47).
Illustration 27 g01283232
38. Use a suitable press in order to remove bearing (47) from shaft (38).
Illustration 28 g01283244
39. Remove retaining ring (49) and bearing race (50).
12/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M007...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g01283253
40. Use Tooling (F) in order to remove lip seal (51) from the travel motor housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 11 10:09:31 UTC+0800 2020
13/13
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M007...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 390F EXCAVATOR FEH
Configuration: 390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
390F Excavator Machine Systems
Media Number -UENR0165-05 Publication Date -01/01/2018 Date Updated -24/01/2018
i02563228
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
D 1P-1864 Pliers 1
E 1P-1858 Pliers 1
F 1P-0520 Driver Group 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply a light film of 10W oil to all components before assembly.
1/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01283253
1. Use Tooling (F) in order to install lip seal (51) in the travel motor housing.
Illustration 2 g01283244
2. Install bearing (50) and retaining ring (49).
Illustration 3 g01283329
3. Raise the temperature of bearing (47). Install bearing (47) onto shaft (38).
2/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g01283212
4. Use Tooling (E) in order to install retaining ring (48) onto bearing (47).
Illustration 5 g01283209
5. Install shaft (38) and bearing (47) into the motor housing.
Illustration 6 g01283206
6. Use Tooling (D) in order to install retaining ring (46) onto shaft (38).
3/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 10 g01283175
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
9. Install springs (42).
10. Install guide (41).
Illustration 11 g01283155
11. Install retainer (40) and piston assemblies (39) into barrel assembly (37). These components
must be reinstalled in the original location.
5/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 12 g01283139
Note: Barrel assembly (37), piston assemblies (39), and retainer (40) must remain intact
during installation onto shaft (38).
12. Position the travel motor sideways.
Illustration 13 g01283138
13. Carefully install barrel assembly (37) onto shaft (38).
Illustration 14 g01283133
14. Install separator plates (35) and friction plates (36) into the travel motor.
6/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 15 g01283129
15. Install O-ring seals (33) and (34) into the travel motor.
Illustration 16 g01283110
Note: Piston (32) must be reinstalled in the original location.
16. Install piston (32).
Illustration 17 g01283350
7/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Note the location of springs (30) for installation.
17. Install springs (30) and O-ring seals (31) to the travel motor.
Illustration 18 g01283096
18. Lower the temperature of bearing (28). Install bearing (28) in the head.
Illustration 19 g01283088
19. Install O-ring seals (25), (26), and (27) on pressure reducing valve (24).
8/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 20 g01283083
20. Install pressure reducing valve (24). Tighten pressure reducing valve (24) to a torque of
44 ± 4 N·m (33 ± 3 lb ft).
21. Install cap (23).
Illustration 21 g01283075
22. Install O-ring seal (22) onto plug (17). Install spool (21) and plug (17) to the head.
23. Install O-ring seal (19) onto plug (18). Install spring (20) and plug (18) to the head.
24. Tighten plugs (17) and (18) to a torque of 74 ± 7 N·m (55 ± 5 lb ft).
9/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M00727...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 22 g01283060
25. Install spool (16).
Illustration 23 g01283057
26. Install plug (15).
Illustration 24 g01283049
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install O-ring seals (10), (12), and (14) and backup rings (11) and (13).
28. Install piston (5), spring (6), spool (7), and spring (8) in body (9). Install cap (4) in body (9).
29. Repeat Steps 27 and 28 for the assembly of the other relief valve.
10/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M007...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 25 g01283045
30. Install relief valves (3). Tighten relief valves (3) to a torque of 177 ± 18 N·m
(131 ± 13 lb ft).
Illustration 26 g01283396
31. Use light grease to install port plate (29) on the head.
11/12
390F L Excavator FEH00001-UP (MACHINE) POWERED BY C18 Engine(M007...
2020/12/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...