This service repair manual provides instructions for removing and installing various engine components on a Caterpillar C15 and C18 engine, including:
1) Removing the variable valve actuator by disconnecting harnesses, removing bolts and nuts, and removing the actuator component.
2) Removing the rocker arm and shaft by removing bolts and using a lifting bracket to remove the assembly as a unit.
3) Disassembling the rocker arm by removing adjustment screws, jam nuts, buttons, and O-rings.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for removing and installing various components of the valve train on a Caterpillar C18 engine, including:
1) Removing the valve actuator, rocker arms, rocker shaft, and disassembling the rocker arms.
2) Instructions include using proper tools, cleaning parts, and torquing fasteners to the specified values.
3) Reassembling and installing the rocker arms, rocker shaft, and valve actuator, and adjusting valves and injectors.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma000...f9iosoidd
The document provides instructions for removing and installing various components of a Caterpillar C-18 engine, including:
- Removing the variable valve actuator by disconnecting harnesses and removing mounting bolts and nuts.
- Installing the variable valve actuator by positioning it and securing with bolts, nuts and reconnecting harnesses.
- Removing the rocker arm and shaft assembly as a unit using a lifting bracket tool.
- Disassembling the rocker arm by removing adjustment screws, buttons, O-rings, and rocker arms from the shaft.
- Reassembling the rocker arm by installing adjustment screws and buttons with new O-rings and mounting the arms on the
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for removing and installing various components of the valve train on a Caterpillar C18 engine, including:
1) Removing the valve actuator, rocker arms, rocker shaft, and disassembling the rocker arms.
2) Instructions include using proper tools, cleaning parts, and torquing fasteners to the specified values.
3) Reassembling and installing the rocker arms, rocker shaft, and valve actuator, and adjusting valves and injectors.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma000...f9iosoidd
The document provides instructions for removing and installing various components of a Caterpillar C-18 engine, including:
- Removing the variable valve actuator by disconnecting harnesses and removing mounting bolts and nuts.
- Installing the variable valve actuator by positioning it and securing with bolts, nuts and reconnecting harnesses.
- Removing the rocker arm and shaft assembly as a unit using a lifting bracket tool.
- Disassembling the rocker arm by removing adjustment screws, buttons, O-rings, and rocker arms from the shaft.
- Reassembling the rocker arm by installing adjustment screws and buttons with new O-rings and mounting the arms on the
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
The document provides instructions for servicing components of a Caterpillar C-18 engine, including:
1) Removing and installing the variable valve actuator, which involves disconnecting harness assemblies and removing mounting bolts and nuts.
2) Disassembling and assembling the rocker arms, which involves removing adjustment screws, buttons, and O-rings.
3) Removing and installing the rocker arm shaft assembly using a lifting bracket to position the assembly, and tightening mounting bolts in a specific sequence.
Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma000...fjkskefksmeme
This document provides instructions for removing and installing various components of a Caterpillar C-18 diesel engine, including:
1. Removing the variable valve actuator by disconnecting harnesses and removing mounting bolts and nuts.
2. Installing the variable valve actuator by reinstalling mounting hardware and reconnecting harnesses.
3. Removing the rocker arm assembly by removing mounting bolts and using a lifting bracket.
4. Disassembling the rocker arm by removing adjustment screws, buttons, seals, and arms from the rocker shaft.
This document provides instructions for removing and installing a variable valve actuator on a Caterpillar 385C FS Excavator. It describes removing the valve mechanism cover, disconnecting harnesses, and removing bolts and nuts to detach the actuator. Reinstallation involves reversing these steps and adjusting lash and compression brake settings. Removal of rocker arms and shafts and disassembly/reassembly of individual rocker arms is also outlined.
This service repair manual provides instructions for removing and installing the variable valve actuator and rocker arm assembly on a Caterpillar C-18 engine. The manual specifies the required tools and outlines the step-by-step procedures for removal and installation, which include disconnecting electrical connectors, removing mounting bolts and nuts, and adjusting clearances upon reinstallation. Technicians are advised to keep components clean and lubricated to prevent premature wear.
This service repair manual provides instructions for removing and installing the variable valve actuator and rocker arm assembly on a Caterpillar C-18 engine. The removal process involves disconnecting electrical connectors, removing mounting bolts and nuts, and using a lifting bracket to remove the assembly. The installation process specifies tightening torques for mounting hardware and adjusting valves and injectors after installation. The document provides detailed illustrations and instructions to guide technicians through the process.
Caterpillar cat 385 c fs excavator (prefix eam) service repair manual (eam000...fjkskefksmeme
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Diagrams and specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and lubricated during disassembly and reassembly.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This document provides instructions for removing and installing various components of a Caterpillar 385C FS excavator engine, including:
1. The valve actuator is removed by disconnecting harnesses and removing bolts and nuts.
2. The rocker arm assembly is removed by taking out studs from the variable valve actuator and rocker arms.
3. The rocker arm and shaft are removed as a unit after removing bolts, using a lifting bracket tool.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
Caterpillar cat 385 c fs excavator (prefix eam) service repair manual (eam000...f9iosoidd
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
Caterpillar cat 385 c fs excavator (prefix t2f) service repair manual (t2f000...ifkkdmdmdm
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides disassembly instructions for the piston pump (implement) on a 962L Wheel Loader. It outlines 26 steps to fully disassemble the pump, including removing components like the head assembly, pump body, pistons, seals, and bearings. Various tools are required to aid in disassembly, like lifting eyes, threaded rods, and a bearing puller. Safety precautions are provided to warn of potential spring hazards.
This document provides instructions for disassembling and assembling the piston pump of the steering system on a 962K wheel loader. It lists the required tools and presents 28 steps for disassembly and 27 steps for assembly, with illustrations showing how to remove and install each component. Key steps include using retaining ring pliers to remove springs and pistons from the barrel assembly, and taking care when compressing springs during assembly to prevent injury.
More Related Content
Similar to Caterpillar Cat 385C FS Excavator (Prefix MMA) Service Repair Manual (MMA00001 and up).pdf
Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma000...fjkskefksmeme
This document provides instructions for removing and installing various components of a Caterpillar C-18 diesel engine, including:
1. Removing the variable valve actuator by disconnecting harnesses and removing mounting bolts and nuts.
2. Installing the variable valve actuator by reinstalling mounting hardware and reconnecting harnesses.
3. Removing the rocker arm assembly by removing mounting bolts and using a lifting bracket.
4. Disassembling the rocker arm by removing adjustment screws, buttons, seals, and arms from the rocker shaft.
This document provides instructions for removing and installing a variable valve actuator on a Caterpillar 385C FS Excavator. It describes removing the valve mechanism cover, disconnecting harnesses, and removing bolts and nuts to detach the actuator. Reinstallation involves reversing these steps and adjusting lash and compression brake settings. Removal of rocker arms and shafts and disassembly/reassembly of individual rocker arms is also outlined.
This service repair manual provides instructions for removing and installing the variable valve actuator and rocker arm assembly on a Caterpillar C-18 engine. The manual specifies the required tools and outlines the step-by-step procedures for removal and installation, which include disconnecting electrical connectors, removing mounting bolts and nuts, and adjusting clearances upon reinstallation. Technicians are advised to keep components clean and lubricated to prevent premature wear.
This service repair manual provides instructions for removing and installing the variable valve actuator and rocker arm assembly on a Caterpillar C-18 engine. The removal process involves disconnecting electrical connectors, removing mounting bolts and nuts, and using a lifting bracket to remove the assembly. The installation process specifies tightening torques for mounting hardware and adjusting valves and injectors after installation. The document provides detailed illustrations and instructions to guide technicians through the process.
Caterpillar cat 385 c fs excavator (prefix eam) service repair manual (eam000...fjkskefksmeme
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Diagrams and specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and lubricated during disassembly and reassembly.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This document provides instructions for removing and installing various components of a Caterpillar 385C FS excavator engine, including:
1. The valve actuator is removed by disconnecting harnesses and removing bolts and nuts.
2. The rocker arm assembly is removed by taking out studs from the variable valve actuator and rocker arms.
3. The rocker arm and shaft are removed as a unit after removing bolts, using a lifting bracket tool.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
Caterpillar cat 385 c fs excavator (prefix eam) service repair manual (eam000...f9iosoidd
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Detailed illustrations and torque specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and follow all safety notices.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
Caterpillar cat 385 c fs excavator (prefix t2f) service repair manual (t2f000...ifkkdmdmdm
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
This document provides instructions for removing and installing various components of a Caterpillar C18 engine, including the cylinder head. The removal procedure for the cylinder head involves first removing the camshaft gear, electronic unit injectors, valve mechanism cover base, and turbochargers. It then instructs to drain the cooling system and remove bolts, thrust plates, sealing plates, and O-rings from the cylinder head.
Similar to Caterpillar Cat 385C FS Excavator (Prefix MMA) Service Repair Manual (MMA00001 and up).pdf (20)
This document provides disassembly instructions for the piston pump (implement) on a 962L Wheel Loader. It outlines 26 steps to fully disassemble the pump, including removing components like the head assembly, pump body, pistons, seals, and bearings. Various tools are required to aid in disassembly, like lifting eyes, threaded rods, and a bearing puller. Safety precautions are provided to warn of potential spring hazards.
This document provides instructions for disassembling and assembling the piston pump of the steering system on a 962K wheel loader. It lists the required tools and presents 28 steps for disassembly and 27 steps for assembly, with illustrations showing how to remove and install each component. Key steps include using retaining ring pliers to remove springs and pistons from the barrel assembly, and taking care when compressing springs during assembly to prevent injury.
This document provides instructions for assembling and disassembling components of a 962K wheel loader. It describes in detail the steps to assemble the piston pump implement, including installing various parts like bearings, seals, pistons, and covers. It also outlines the procedure to remove and install the electrohydraulic control and main control valve, noting required tools and safety precautions.
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 962K wheel loader. It outlines 28 steps for disassembly of the steering pump that include removing bolts, valves, seals, spools, plugs, springs, and other components. The assembly section lists 34 steps for reinstalling components in reverse order and adjusting axial shaft end play.
This document provides instructions for assembling and disassembling components of the transmission system for a 962H wheel loader. It describes in detail the procedure for assembling the torque converter, separating the transmission from the output transfer gears, and disassembling the transmission planetary. The assembly procedure involves 28 steps connecting and securing various transmission components using tools like eyebolts and retaining ring pliers. The disassembly procedures describe 4 steps for separating the transmission and 5 initial steps for disassembling the transmission planetary. Illustrations are provided to supplement the text instructions.
This document provides disassembly and assembly instructions for the piston pump of a 950H wheel loader. The disassembly instructions list 28 steps to fully disassemble the pump, removing components like valves, plugs, springs, and bearings. The assembly section then lists 29 steps to reassemble the pump, providing the reverse of the disassembly instructions and noting any specific tools or precautions needed.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It describes 57 assembly steps to install various transmission components such as bearings, gears, shafts, seals, and housings. Cleanliness is important during assembly and all parts must be thoroughly cleaned before installation. Lubrication with transmission oil is also required for internal parts. Proper tooling is listed for expanding retaining rings and installing components.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists the required tools and outlines 35 steps to disassemble components such as the housing assembly, impeller, carrier shaft, stator, and turbine. These components are then reassembled in the reverse order, with notes on cleaning parts and using new parts for any that are worn or damaged.
The document provides instructions for assembling and installing the gear pump for an axle oil cooler on a Caterpillar 950H wheel loader. It describes 20 steps to install bearings, seals, gears, shafts, and covers onto the gear pump body. It then provides instructions for installing the assembled gear pump along with the axle oil cooler pump and clutch.
Caterpillar Cat 950F SERIES II WHEEL LOADER (Prefix 4DJ) Service Repair Manua...aags15120808
This document provides instructions for disassembling a Type IV governor used in Caterpillar 3114, 3116, and 3126 engines. It lists the required tools and parts that should be replaced during disassembly. The instructions describe how to remove each component in a step-by-step process, including covers, springs, flyweights, shafts, and other internal parts. Cautions are provided regarding contained fluids and released spring forces during disassembly.
Caterpillar Cat 938G II Wheel Loader (Prefix RTB) Service Repair Manual (RTB0...aags15120808
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II wheel loader. It describes how to remove components such as the axle shaft, planetary carrier assembly, retaining rings, and seals. Detailed steps are provided for disassembling the planetary carrier assembly. The assembly procedure describes how to install components in reverse order and includes notes about properly installing duo-cone seals. Tools required are listed.
Caterpillar Cat 938G II Wheel Loader (Prefix PHN) Service Repair Manual (PHN0...aags15120808
This document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II Wheel Loader. Key steps include:
1. Removing bolts, seals, and gears to disassemble the oil pump.
2. Assembling involves installing gears, seals, bearings and bolts in reverse order.
3. Removing hoses and bolts to take off the relief valve.
In 3 sentences, this summary outlines the main components worked on (transmission oil pump and relief valve), some key disassembly/assembly steps (removing/installing bolts, gears, seals), and identifies the machine model and components discussed
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 3046 engine. It outlines the required tools and gives step-by-step procedures for removing and installing the valve springs without removing the cylinder head. Key steps include using air pressure and valve spring compressors to hold the valves in place while removing and installing the springs and valve keepers. The document also provides instructions for fully removing and installing the inlet and exhaust valves which requires first removing the cylinder head.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 3046 engine. It outlines the necessary tools and gives step-by-step procedures for removing the old guides from the cylinder head and installing the new ones. Safety notices are included to keep parts clean and contain fluids. The summary provides essential information on the content and purpose of the document in 3 sentences or less.
This document provides instructions for disassembling and assembling the piston pump of a 930K wheel loader. The disassembly procedure involves removing 22 numbered components of the pump in sequential order. The assembly procedure instructs assembling the pump components in the reverse order, and includes checks to ensure proper bearing preload. Special tools and safety precautions are noted throughout.
This service repair manual provides instructions for disassembling and assembling the transmission of a 930K wheel loader. It details over 40 steps to remove the transmission and disassemble its components. This includes using various tools to remove parts like bearings, seals, sensors, fittings, plates, shafts and housings. Diagrams are provided to illustrate each step. Proper care is noted to lift heavy transmission parts using lifting devices and jack stands.
The document provides instructions for disassembling and assembling the piston pump of a 725C articulated truck. It describes:
- Removing four socket head bolts and the pressure and flow compensator valve from the steering piston pump.
- Removing three O-rings from the pressure and flow compensator valve.
- Removing the plug and seal from the pressure and flow compensator valve.
- Detailed step-by-step instructions and illustrations for disassembling and assembling the various components of the piston pump, including checking clearances and applying locking compounds.
The document provides step-by-step instructions for disassembling and assembling the torque converter of a 725C articulated truck. It details 43 steps to disassemble components like the retarder, separator plate, center shaft, carrier assembly, torque converter impeller, stator, turbine, housings, and seals. It also lists the required tools needed and warns of safety precautions when lifting or blocking heavy components during the process.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. It begins by listing the required tools. It then provides step-by-step instructions and accompanying illustrations to remove components such as pressure valves, springs, seals, pistons, bearings, and housings. Special care notes are included when removing pressurized or spring-loaded parts. The overall process yields the individual internal parts of the piston pump for maintenance or replacement.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...aags15120808
This document provides instructions for disassembling and assembling the travel motor of a 390F hydraulic excavator. It outlines 40 steps for disassembly, removing components like the head, relief valves, spools, pistons, barrel assembly, swashplate and shaft. It then outlines 32 steps for reassembly, installing these components in reverse order while noting alignment marks and applying lubricant. Precautions are provided for spring loaded components.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02905549
Valve Actuator (Variable) - Remove
SMCS - 1105-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Note: Do not disassemble the variable valve actuator after the component has been removed. Any
attempt to disassemble the variable valve actuator will void the warranty of the component.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
1/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01446246
1. Disconnect harness assembly (4). Disconnect harness assembly (1).
2. Remove bolt (2). Remove four nuts (3) and two nuts (6).
3. Remove variable valve actuator (5).
Illustration 2 g01446248
4. Remove support (11) and stud (10).
2/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Remove two studs (9) and three studs (7).
6. Remove rocker arm assembly (8).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:41:36 UTC+0800 2020
3/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02905633
Valve Actuator (Variable) - Install
SMCS - 1105-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01446248
1/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g01446408
1. Install two studs (9) at Location 6 and Location 7. Tighten studs (9) to a torque of
47 ± 9 N·m (35 ± 7 lb ft).
2. Install stud (10) at Location 2. Tighten stud (10) to a torque of 65 ± 10 N·m (48 ± 7 lb ft).
Install support (11).
3. Position rocker arm assembly (8). Install three studs (7) at Location 3, Location 4, and
Location 5. Tighten studs (7) to a torque of 50 ± 5 N·m (37 ± 4 lb ft). Turn studs (7) for an
additional 45 ± 5 degrees.
Illustration 3 g01446246
4. Install variable valve actuator (5).
5. Install bolt (2). Install four nuts (3). Install two nuts (6). Refer to the tightening sequence.
6. Tighten bolt (2) to a torque of 105 ± 20 N·m (77 ± 15 lb ft). Tighten nuts (3) to a torque of
105 ± 20 N·m (77 ± 15 lb ft). Tighten nuts (6) to a torque of 47 ± 9 N·m (35 ± 7 lb ft).
Tighten the nuts and the bolt in a numerical sequence.
7. Connect harness assembly (4). Connect harness assembly (1) to variable valve actuator (5).
2/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01446444
8. First adjust the lash on the exhaust and then adjust the compression brake on variable valve
actuator (5). Refer to Testing and Adjusting, "Compression Brake Lash - Adjust" for more
information on adjusting the lash for the compression brake. Tighten jam nut (12) to a
torque of 15 ± 3 N·m (11 ± 2 lb ft).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:42:33 UTC+0800 2020
3/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02906282
Rocker Arm and Shaft - Remove
SMCS - 1102-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 124-2946 Lifting Bracket 1
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
B. Remove the variable valve actuator, if necessary. Refer to Disassembly and Assembly,
"Valve Actuator (Variable) - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01117306
1. Remove bolts (2) .
2. Use Tooling (A) to remove rocker arm shaft assembly (4) , valve rocker arms (3) , and
electronic unit injector rocker arms (1) as a unit.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:43:30 UTC+0800 2020
2/2
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i04997049
Rocker Arm - Disassemble
SMCS - 1123-015
Disassembly Procedure
Start By:
a. Remove the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01047557
1. Remove valve rocker arms (11) and electronic unit injector rocker arm (3) from rocker shaft
assembly (4).
2. Remove jam nut (7) from adjustment screw (8).
3. Remove adjustment screw (8) from valve rocker arms (11).
4. Remove button (10) from adjustment screw (8). Remove O-ring seal (9) from the
adjustment screw.
5. Remove jam nut (2) from unit injector adjustment screw (1).
6. Remove unit injector adjustment screw (1) from electronic unit injector rocker arm (3).
7. Remove button (6) from unit injector adjustment screw (1). Remove O-ring seal (5) from
the unit injector adjustment screw.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:44:26 UTC+0800 2020
2/2
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i04998150
Rocker Arm - Assemble
SMCS - 1123-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01047557
1/2
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Do not reuse the O-ring seal on the adjustment screw if the button is removed from
the adjustment screw.
1. Install O-ring seal (9) in button (10).
2. Use a soft hammer to seat button (10) on adjustment screw (8).
3. Install adjustment screw (8) in valve rocker arms (11). Install jam nut (7) on the adjustment
screw.
4. Install O-ring seal (5) in button (6).
5. Use a soft hammer to seat button (6) on unit injector adjustment screw (1).
6. Install unit injector adjustment screw (1) in electronic unit injector rocker arm (3). Install
jam nut (2) on the unit injector adjustment screw.
7. Lubricate rocker shaft assembly (4) with clean engine oil.
8. Install valve rocker arms (11) and electronic unit injector rocker arm (3) on rocker shaft
assembly (4).
End By:
a. Install the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:45:23 UTC+0800 2020
2/2
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i07394739
Rocker Arm and Shaft - Install
SMCS - 1102-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 124-2946 Lifting Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01117306
Illustration 2 g01325993
1. Position rocker arm shaft assembly (4), valve rocker arms (3), and electronic unit injector
rocker arms (1) as a unit with Tooling (A) on the cylinder head.
Note: Apply clean engine oil to the underside of the bolt heads prior to installation.
2/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 2. Install bolts (2) and tighten to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Tighten bolts (2) again
to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Turn bolts (2) for an additional 60 ± 5 degrees.
Tighten the bolts in the following sequence: 2, 3, 1, 4.
3. Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit
Injector - Adjust".
4. Adjust the engine valve lash. Refer to Testing and Adjusting, "Engine Valve Lash-
Inspect/Adjust".
End By:
a. Install the variable valve actuator, if necessary. Refer to Disassembly and Assembly, "Valve
Actuator (Variable) - Install".
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:46:20 UTC+0800 2020
3/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02211115
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
c. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
d. Remove the turbochargers. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1. Drain the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
Illustration 1 g01056681
2. Remove bolts (2) and thrust plate (1).
2/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01116390
3. Remove sealing plate (3) and adapter assembly (4).
Illustration 3 g01056684
4. Remove O-ring seal (5) and O-ring seal (6) from sealing plate (3).
3/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 4 g01117768
5. Disconnect hose assembly (8).
6. Disconnect hose assembly (12).
7. Remove bolts (10). Position fuel filter base (9) out of the way.
8. Remove bolt (11) and the breather tube from the cylinder head.
9. Remove bolts (7) and remove the bracket from the cylinder head.
10. Disconnect boost pressure sensor (13).
11. Disconnect inlet air temperature sensor (14).
4/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 5 g01116398
12. Remove water temperature regulator housing (17).
13. Remove strap (18).
14. Attach a suitable lifting device to cylinder head (16). The weight of the cylinder head is
approximately 235 kg (518 lb).
15. Remove cylinder head bolts (15).
16. Carefully remove cylinder head (16).
5/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 6 g01117797
17. Remove cylinder head gasket (19).
18. Remove spacer plate (20).
19. Remove seals (24) and seal (22).
20. Remove spacer plate gasket (23).
21. Remove O-ring seal (21) from the dowel in the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:47:17 UTC+0800 2020
6/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i04410295
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4876 Lubricant 1
B 8T-2998 Lubricant 1
C 9S-3263 Thread Lock Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01117797
1. Install O-ring seal (21) on the dowel in the cylinder block.
2. Install spacer plate gasket (23) on the cylinder block.
3. Install seals (24) and seal (22) .
4. Install spacer plate (20) .
5. Install cylinder head gasket (19) on the spacer plate.
2/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 2 g01116398
6. Attach a suitable lifting device to cylinder head (16) . The weight of the cylinder head is
approximately 235 kg (518 lb).
7. Carefully install cylinder head (16) on the dowel pins on the cylinder block.
3/6
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...