The document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It outlines the following steps:
1. Remove various engine components to access the cylinder head, including the accessory drive, intake manifold, fumes disposal group, electronic unit injectors, exhaust gas valve, and exhaust manifold.
2. Disconnect tube, hose, and harness assemblies from the cylinder head.
3. Attach a lifting device to the cylinder head due to its weight of approximately 204 kg, then remove the bolts and lift off the cylinder head and gasket.
4. Clean and inspect all parts, applying anti-seize compound to bolt threads as needed, then install the
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
This document provides instructions for disassembling the piston pump of a Caterpillar 236B3 skid steer loader. It outlines 53 steps to remove components like covers, springs, seals, studs, nuts, plates and assemblies. Special tools are required and safety precautions mentioned, like wearing protective equipment when removing parts with spring forces. Components must be marked for correct reassembly.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil to components. Precise installation of each part is outlined.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 18 m3 motor grader (prefix e9w) service repair manual (e9w000...dujjsjekkkdmm
The document provides instructions for removing and installing a bank valve on a Caterpillar 18M3 motor grader. It describes disconnecting hydraulic lines and removing mounting bolts to remove the bank valve. For installation, the instructions note to inspect O-rings and replace any that are worn before reversing the removal steps and reconnecting hydraulic lines. Personal safety warnings are provided regarding potential hazards from hydraulic pressure and spring forces.
Caterpillar cat 390 f excavator (prefix feh) service repair manual (feh00001 ...fjkskedmme
The document provides instructions for disassembling and assembling the travel motor of a 390F excavator. It describes 40 steps to disassemble the various components of the travel motor including removing the head, relief valves, spools, pistons, plates, seals and bearings. It then describes 36 steps for reassembling the components in reverse order, making sure to align marks and reinstall parts in their original locations. Precautions are provided regarding spring loaded components.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...fjsekdmmeed
The document provides instructions for removing and installing the flywheel and crankshaft pulley on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel housing, and crankshaft pulley. Detailed steps and illustrations are provided for disassembling and reassembling these parts, including cleaning, inspecting, and applying sealants to mating surfaces. Safety notices advise keeping parts clean and containing fluids.
This document provides instructions for disassembling the piston pump of a Caterpillar 236B3 skid steer loader. It outlines 53 steps to remove components like covers, springs, seals, studs, nuts, plates and assemblies. Special tools are required and safety precautions mentioned, like wearing protective equipment when removing parts with spring forces. Components must be marked for correct reassembly.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. Precise instructions are given, including required tools. Cleaning and inspection of parts is noted. The assembly section then lists the 44 steps in reverse order, noting replacement of seals and application of oil to components. Precise installation of each part is outlined.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 18 m3 motor grader (prefix e9w) service repair manual (e9w000...dujjsjekkkdmm
The document provides instructions for removing and installing a bank valve on a Caterpillar 18M3 motor grader. It describes disconnecting hydraulic lines and removing mounting bolts to remove the bank valve. For installation, the instructions note to inspect O-rings and replace any that are worn before reversing the removal steps and reconnecting hydraulic lines. Personal safety warnings are provided regarding potential hazards from hydraulic pressure and spring forces.
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...fjsekdmmeed
This document provides instructions for removing and installing the fuel injection pump housing and governor of a 120G Motor Grader. It is a 10 step process to remove the parts which includes using various tools to remove bolts, nuts, tubes and the housing itself. The 8 step process to install includes positioning bearings, installing the camshaft, washer, snap ring and other parts, and ensuring proper timing of the governor.
Caterpillar cat 993 k wheel loader (prefix z8d) service repair manual (z8d000...ufjkskemfseol
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...uudfjjjskkemmd
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 336 d2 l excavator (prefix dgr) service repair manual (dgr000...pfiskdmjekm
This document provides instructions for removing and installing a unit injector and unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step instructions that include disconnecting fuel lines and electrical connections, cleaning parts, replacing seals, and torquing bolts to specifications. Proper cleaning and installation of parts is emphasized to prevent leaks and engine damage.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step process which includes disconnecting various tube, hose and harness assemblies, removing mounting brackets and bolts, and lifting the cylinder head off once all fasteners are removed. Proper cleaning and lubrication of components is emphasized for reinstallation.
The document provides instructions for servicing various components of a C13 engine, including:
1. Procedures for removing and installing components like the valve mechanism cover base, valve actuator, rocker arm and shaft, and cylinder head.
2. Steps for disassembling and assembling the rocker arm.
3. Lists of required tools and torque specifications for fasteners.
The document is a service repair manual that details removal, installation, disassembly, and assembly procedures for key engine components, providing technicians the information needed to service a C13 engine.
The document provides instructions for servicing various components of a C13 engine, including:
1. Procedures for removing and installing components like the valve mechanism cover base, valve actuator, rocker arm and shaft, and cylinder head.
2. Steps for disassembling and assembling the rocker arm.
3. Lists of required tools and torque specifications for fasteners.
The document is a service repair manual that details removal, installation, disassembly, and assembly procedures for key engine components, providing technicians the information needed to service a C13 engine.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step process which includes disconnecting various tube, hose and harness assemblies, removing mounting brackets and bolts, and using a lifting device to remove the cylinder head due to its significant weight of approximately 204 kg (450 lb). Proper cleaning and inspection of parts is emphasized along with applying anti-seize compound to bolts during installation.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step removal process which includes disconnecting various tube, hose and harness assemblies, as well as removing bolts and brackets. Lifting equipment is required to remove the cylinder head due to its weight of approximately 450 pounds. Reinstallation is performed in the reverse order.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step removal process which includes disconnecting various tube, hose and harness assemblies, as well as removing bolts and brackets. Lifting equipment is required to remove the cylinder head due to its weight of approximately 450 pounds. Reinstallation is performed in the reverse order.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...f8usejkdmmd8i
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires loosening a nut with a socket wrench and using pullers to remove and install components.
3. Removing the crankshaft front seal using a slide hammer puller and drilling holes in the seal. The instructions caution to keep parts clean and contain fluids.
Caterpillar cat 320 d rr excavator (prefix eby) service repair manual (eby000...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...ze6074xunong
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...gongfuao7509
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut to a specified torque.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...8foskkdjdkdm3e
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut to a specified torque.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...yu5676962
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut to a specified torque.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 120 g motor grader (prefix 4hd) service repair manual (4hd000...fjsekdmmeed
This document provides instructions for removing and installing the fuel injection pump housing and governor of a 120G Motor Grader. It is a 10 step process to remove the parts which includes using various tools to remove bolts, nuts, tubes and the housing itself. The 8 step process to install includes positioning bearings, installing the camshaft, washer, snap ring and other parts, and ensuring proper timing of the governor.
Caterpillar cat 993 k wheel loader (prefix z8d) service repair manual (z8d000...ufjkskemfseol
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
Caterpillar cat 235 c excavator (prefix 5af) service repair manual (5af00001 ...uudfjjjskkemmd
1) The document provides instructions for removing and installing a fuel filter base and removing a fuel transfer pump from a Caterpillar 235C excavator.
2) The fuel filter base removal instructions include disconnecting fuel lines and removing bolts and the base. Installation is the reverse.
3) Removing the fuel transfer pump involves turning off fuel supply, disconnecting lines, and removing bolts to access the pump.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 336 d2 l excavator (prefix dgr) service repair manual (dgr000...pfiskdmjekm
This document provides instructions for removing and installing a unit injector and unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step instructions that include disconnecting fuel lines and electrical connections, cleaning parts, replacing seals, and torquing bolts to specifications. Proper cleaning and installation of parts is emphasized to prevent leaks and engine damage.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step process which includes disconnecting various tube, hose and harness assemblies, removing mounting brackets and bolts, and lifting the cylinder head off once all fasteners are removed. Proper cleaning and lubrication of components is emphasized for reinstallation.
The document provides instructions for servicing various components of a C13 engine, including:
1. Procedures for removing and installing components like the valve mechanism cover base, valve actuator, rocker arm and shaft, and cylinder head.
2. Steps for disassembling and assembling the rocker arm.
3. Lists of required tools and torque specifications for fasteners.
The document is a service repair manual that details removal, installation, disassembly, and assembly procedures for key engine components, providing technicians the information needed to service a C13 engine.
The document provides instructions for servicing various components of a C13 engine, including:
1. Procedures for removing and installing components like the valve mechanism cover base, valve actuator, rocker arm and shaft, and cylinder head.
2. Steps for disassembling and assembling the rocker arm.
3. Lists of required tools and torque specifications for fasteners.
The document is a service repair manual that details removal, installation, disassembly, and assembly procedures for key engine components, providing technicians the information needed to service a C13 engine.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step process which includes disconnecting various tube, hose and harness assemblies, removing mounting brackets and bolts, and using a lifting device to remove the cylinder head due to its significant weight of approximately 204 kg (450 lb). Proper cleaning and inspection of parts is emphasized along with applying anti-seize compound to bolts during installation.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step removal process which includes disconnecting various tube, hose and harness assemblies, as well as removing bolts and brackets. Lifting equipment is required to remove the cylinder head due to its weight of approximately 450 pounds. Reinstallation is performed in the reverse order.
This document provides instructions for removing and installing a cylinder head on a Caterpillar C13 engine. It lists the required tools and outlines the step-by-step removal process which includes disconnecting various tube, hose and harness assemblies, as well as removing bolts and brackets. Lifting equipment is required to remove the cylinder head due to its weight of approximately 450 pounds. Reinstallation is performed in the reverse order.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...f8usejkdmmd8i
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires loosening a nut with a socket wrench and using pullers to remove and install components.
3. Removing the crankshaft front seal using a slide hammer puller and drilling holes in the seal. The instructions caution to keep parts clean and contain fluids.
Caterpillar cat 320 d rr excavator (prefix eby) service repair manual (eby000...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...ze6074xunong
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...gongfuao7509
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut to a specified torque.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...8foskkdjdkdm3e
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut to a specified torque.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...yu5676962
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut to a specified torque.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix EBY) Service Repair Ma...f8seodkdmdmed3
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires loosening a nut with a socket wrench and using pullers to remove and install the pulley and oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and drilling holes in the seal. The instructions caution to keep parts clean and contain fluids.
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller.
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and ensuring the crankshaft flange is not damaged.
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires loosening a nut with a socket wrench and using pullers to remove and install the pulley and oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and drilling holes in the seal. The seal is then installed using a special tool.
Similar to Caterpillar cat 352 f xe excavator (prefix mdr) service repair manual (mdr00001 and up) (20)
Caterpillar cat 385 b l excavator (prefix cls) service repair manual (cls0000...fjjskekmsemm
The document provides assembly instructions for control valves on 385B and 385B L excavators. It involves 25 steps to assemble components like spools, seals, plugs, resolver valves, differential relief valves, and covers. Special tools may be required and parts need to be checked for wear before assembly. Springs and other components must be assembled carefully according to the instructions to avoid injury. Torque specifications are provided for tightening certain parts.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. Special steps are provided to determine the correct bearing preload using shims and applying hydraulic pressure.
Caterpillar cat 385 b l excavator (prefix bkf) service repair manual (bkf0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to reassembly.
3) Reassembling the components in reverse order, applying lubricants and determining proper bearing preload using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix rcd) service repair manual (rcd00001 ...fjjskekmsemm
The document provides instructions for disassembling and assembling various components of an excavator control valve, including:
1. Disassembling the proportional valve by removing bolts, nuts, and cartridge components.
2. Assembling the attachment, bucket, and boom control valve by installing O-rings, plugs, resolver valves, springs, and actuator groups.
3. Assembling the right travel, left travel, and stick control valve by installing spools, plugs, resolver valves, O-rings, and covers.
Caterpillar cat 385 b excavator (prefix mya) service repair manual (mya00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and gaskets. Corresponding assembly steps are also provided, with notes to check components for wear and reduce temperature before inserting some parts. The goal is to properly disassemble and reassemble the control valve while preventing contamination.
Caterpillar cat 385 b excavator (prefix fdl) service repair manual (fdl00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing parts in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of O-rings is also noted.
Caterpillar cat 385 b excavator (prefix cls) service repair manual (cls00001 ...fjjskekmsemm
The document provides assembly instructions for control valves for attachment, bucket, boom, right travel, left travel, and stick functions on 385B and 385B L excavators. It involves installing seals, spools, resolver valves, solenoids, pistons, actuators, and covers. Proper torque values are specified and safety precautions are provided due to parts being under spring load.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. It provides details on installing bearings and determining the correct number of shims using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix bkx) service repair manual (bkx00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It includes:
1) A list of required tools for the job.
2) Detailed step-by-step instructions for removing over 30 components of the final drive, including gears, shafts, housings, and seals.
3) Procedures for installing new bearings and determining the proper bearing preload during assembly.
Caterpillar cat 385 b excavator (prefix bkf) service repair manual (bkf00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and includes pressing bearings into place, determining the correct shim thickness, and installing seals. Precise alignment of parts and cleanliness are emphasized throughout.
Caterpillar cat 374 f l excavator (prefix ebf) service repair manual (ebf0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 374F excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, planetary gears and shafts. The assembly process reverses this, applying anti-seize compound and installing components like bearing cups, pins and housings in the correct order. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 374 f excavator (prefix ebf) service repair manual (ebf00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 374F excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, planetary gears and shafts. The assembly process reverses this, applying anti-seize compound and installing components like bearing cups, pins and housings in the correct order. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including gears, shafts, housings and seals. Photos illustrate each step. Assembly requires applying threadlock to fasteners and bearings, and using shims to set the proper bearing preload when reinstalling the main housing. Proper cleaning and inspection of all parts is emphasized before reassembly.
Caterpillar cat 365 c l excavator (prefix mem) service repair manual (mem0000...fjjskekmsemm
This document provides disassembly and assembly instructions for the final drive on a 365C excavator. It describes how to disassemble the various components of the final drive including removing the ring gear, carrier assemblies, gears, shafts and seals. It then describes the assembly process and includes details on cleaning, applying threadlock, installing bearings and seals, and determining the correct shim thickness. The overall document provides a detailed multi-step process for taking apart and rebuilding the final drive assembly.
Caterpillar cat 365 c l excavator (prefix mcs) service repair manual (mcs0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 365C excavator. It outlines 33 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then outlines 11 steps to reassemble the final drive, which includes determining the correct shim thickness between components and installing seals using specialized tools. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the final drive.
Caterpillar cat 365 c l excavator (prefix elc) service repair manual (elc0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor of a 365C excavator. The disassembly process involves 29 steps to remove components like springs, plates, pistons, seals, and bearings. The assembly process reverses the disassembly with 31 steps, including verifying clearances with feeler gauges and heating components before installation. Tools include retaining ring pliers, link brackets, and threaded rods for lifting heavy parts. Personal protective equipment is recommended due to spring-loaded components.
Caterpillar cat 365 c excavator (prefix mem) service repair manual (mem00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 365C excavator. It lists over 30 steps for disassembly, which include removing the final drive cover, carrier assemblies, gears, shafts, seals and bearings. For assembly, it lists 8 steps such as cleaning parts, installing bearings, seals and housing components, and determining the correct number of shims using a micrometer to measure gear dimensions. The overall document provides detailed technical instructions for taking apart and rebuilding the final drive transmission on this excavator model.
Caterpillar cat 365 c excavator (prefix mcs) service repair manual (mcs00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 365C excavator. It describes in detail how to remove over 30 individual parts, including gears, shafts, housings and seals. Reassembly is outlined in similar detail, with requirements to clean parts thoroughly, apply locking compounds, and properly set bearing preloads using shims. Proper tools are listed to facilitate disassembly and assembly.
Caterpillar cat 365 c excavator (prefix elc) service repair manual (elc00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor of a 365C excavator. The disassembly process involves 29 steps to remove components like springs, plates, pistons, seals, and bearings. The assembly process reverses the disassembly with 31 steps, including verifying clearances with feeler gauges and heating components before installation. Tools required include retaining ring pliers, link brackets, and threaded rods for lifting. Personal safety warnings are provided throughout.
Caterpillar cat 365 b mh excavator (prefix cty) service repair manual (cty000...fjjskekmsemm
1) The document provides assembly instructions for a final drive on an excavator. It details cleaning parts, applying anti-seize compound, installing bearings and seals, and adjusting bearing preload using shims.
2) Carrier assemblies are assembled by installing bearings, thrust washers, and planetary gears, then securing with spring pins.
3) Carrier assemblies are installed in the ring gear and main housing, and components are secured with bolts torqued to specification.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03533151
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
a. Remove the valve cover.
Illustration 1 g01861473
1. Disconnect harness assembly (1).
1/3
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01861475
2. Loosen hose clamp (4). Remove bolts (3) and remove breather (2).
Illustration 3 g01861477
3. Remove element (5).
Illustration 4 g01861478
4. Disconnect harness assemblies (6) and (8). Remove valve cover base (7).
2/3
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01861512
5. Remove seal (9) from valve cover base (7).
Installation Procedure
1. Install valve cover base (7) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:16:28 UTC+0800 2020
3/3
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i06762189
Valve Actuator (Variable) - Remove and Install
SMCS - 1105-010
Removal Procedure
Start By:
a. Remove the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of
the components should be cleaned thoroughly. This will help to prevent dirt from entering the
internal mechanism.
Illustration 1 g01265475
1/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Disconnect harness assemblies (3). Remove bolts (1) and nuts (2). Remove valve actuator
(4).
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
Illustration 2 g01265475
1. Position valve actuator (4). Install bolts (1) and nuts (2). Tighten bolts (1) and nuts (2) to a
torque of 100 ± 20 N·m (74 ± 15 lb ft). Connect harness assemblies (3).
2. Adjust the valve actuators. Refer to Testing and Adjusting, "Variable Valve Actuators -
Inspect/Adjust" for the proper procedure.
End By:
a. Install the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:17:24 UTC+0800 2020
2/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i07074651
Rocker Arm and Shaft - Remove and Install
SMCS - 1102-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 293-2989 Lift Bracket As 1
Start By:
a. Remove the valve cover.
Illustration 1 g01861123
1. Remove bolts (1).
2. Use Tooling (A) to remove rocker arm and shaft (2). Remove pushrods (3).
1/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Installation Procedure
1. Install rocker arm and shaft (2) in the reverse order of removal.
a. Lubricate the contact points of pushrods (3) with clean engine oil. Install pushrods
(3).
b. Tighten bolts (1) to standard torque.
c. Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit
Injector - Adjust".
d. Adjust the engine valve lash. Refer to Testing and Adjusting, "Engine Valve Lash -
Inspect/Adjust".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:18:19 UTC+0800 2020
2/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03552706
Rocker Arm - Disassemble
SMCS - 1123-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
Start By:
a. Remove the rocker arm and shaft.
Illustration 1 g01262570
Note: Place an identification mark on all components for assembly purposes.
Note: Stand (5) has an offset hole.
1/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 1. Remove stands (1).
2. Remove rocker arms (2), rocker arms (3), rocker arms (4), and stand (5) from shaft (6).
3. Use Tooling (A) to remove the bushings from the rocker arms (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:19:15 UTC+0800 2020
2/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03552709
Rocker Arm - Assemble
SMCS - 1123-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Use Tooling (A) to install the bushings for rocker arms (3). For correct bearing dimensions,
refer to Specifications, "Electronic Unit Injector Rocker Arm" and Specifications, "Valve
Mechanism".
Illustration 1 g01262570
2. Install stand (5), rocker arms (4), rocker arms (3), and rocker arms (2) onto shaft (6).
Note: Stand (5) has an offset hole.
1/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 3. Install stands (1).
End By:
a. Install the rocker arm and shaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:20:11 UTC+0800 2020
2/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i07071018
Cylinder Head - Remove and Install
SMCS - 1100-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Graphite- 50 Anti-Seize -
Start By:
a. Remove the accessory drive.
b. Remove the intake manifold.
c. Remove the fumes disposal group.
d. Remove the electronic unit injectors.
e. Remove the exhaust gas valve (NRS).
f. Remove the exhaust cooler (NRS).
g. Remove the exhaust manifold.
Illustration 1 g01890955
1/3
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 1. Disconnect tube assembly (1). Disconnect the tube and hose assemblies (2). Remove bolts (3) and bracket
(4).
Illustration 2 g01890956
2. Remove tube assembly (5). Disconnect hose assembly (8).
3. Remove bolts (6) and nut (9). Reposition harness assembly (7).
Illustration 3 g01890957
4. Remove housing (10) and tube (11).
Illustration 4 g01890958
5. Attach a suitable lifting device to cylinder head (14). The weight of cylinder head (14) is approximately
204 kg (450 lb).
6. Remove bolts (12) and (13). Remove cylinder head (14) and the cylinder head gasket.
Installation Procedure
2/3
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Inspect the cylinder head and the cylinder block for flatness. Refer to Guideline for Reusable Parts and
Salvage Operations, SEBF8162, "Procedure to Measure and Salvage Cylinder Head Assemblies and
Related Components".
2. Install cylinder head (14) in reverse order of removal.
a. Install a new head gasket.
b. Apply Tooling (A) to the threads of bolts (12), (13), and both sides of the washers.
c. Install bolts (12) and (13). Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines".
Illustration 5 g00950659
d. Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 170 ± 10 N·m
(125 ± 7 lb ft).
e. Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 170 ± 10 N·m
(125 ± 7 lb ft).
f. Place a mark on bolt (1) through bolt (26). Rotate bolt (1) through bolt (26) in a numerical sequence
for an additional 120 ± 5 degrees (1/3 turn).
g. Loosen bolt (1) through bolt (26) until the washers are loose under the Bolt heads.
h. Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 170 ± 10 N·m
(125 ± 7 lb ft).
i. Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 170 ± 10 N·m
(125 ± 7 lb ft).
j. Place a mark on bolt (1) through bolt (26). Rotate bolt (1) through bolt (26) in a numerical sequence
for an additional 120 ± 5 degrees (1/3 turn).
k. Tighten bolt (27) through bolt (34) in a numerical sequence to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:21:07 UTC+0800 2020
3/3
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03554743
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
a. Remove the cylinder head.
Illustration 1 g01138716
1. Remove bolts (1).
2. Remove lifter group (2).
1/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Installation Procedure
1. Install lifter group (2) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:22:03 UTC+0800 2020
2/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05331988
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7638 Magnetic Holding Tool 18
B
201-4211 Camshaft Pilot 1
201-4212 Camshaft Pilot 1
Start By:
a. Remove the rocker arms and shafts.
b. Remove the front cover.
c. Remove the camshaft position sensor.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel.
1/5
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01878122
2. Install Tooling (A) in order to support the lifter. Repeat for all the remaining lifters.
Illustration 2 g03377797
2/5
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g03377808
Note: Lubricate Tooling (B) for easier removal of the camshaft. Lubrication also prevents
damaging the camshaft lobes and the camshaft bearings.
6. Use two people to remove camshaft (7). The weight of camshaft (7) and the camshaft gear
is approximately 34 kg (75 lb). Carefully remove camshaft (7) from the engine. Support the
weight of the camshaft during removal.
Note: Rotate the camshaft during removal. This action will prevent the camshaft from
binding in the camshaft bearings.
Installation Procedure
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
4/5
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Note: Ensure that camshaft (6) and Tooling (B) are clean. Apply clean engine oil to the lobes and
journals of camshaft (6) and Tooling (B).
Note: During installation of camshaft (6), rotate the camshaft in both directions in order to prevent
binding in the camshaft bearing bores.
1. Install camshaft (6) in the reverse order of removal.
Illustration 6 g01292427
a. Ensure that the timing Marks (X) on the idler gear aligned with the timing marks on
the crankshaft gear and the camshaft drive gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:22:58 UTC+0800 2020
5/5
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05351535
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
A. Remove the camshaft.
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g00522082
1/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. NOTICE
Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Use a suitable press to remove drive gear (1) from camshaft (3) .
3. Remove woodruff key (2) .
Installation Procedure
1. Install drive gear (1) in the reverse order of removal.
a. Raise the temperature of drive gear (1) to a temperature of 315° C (600° F).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 5 10:23:54 UTC+0800 2020
2/2
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 352F EXCAVATOR MDR
Configuration: 352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05332615
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
201-4214 Receiving Sleeve 1
201-4213 Puller Plate 1
201-4209 Bearing Pilot 1
201-4208 Backup Plate 1
6F-7032 Bolt 1
8M-8778 Taperlock Stud 1
8S-8292 Extension (Short) 2
8S-8293 Extension (Long) 1
B 185-3989 Thread Lubricant 1
Start By:
a. Remove the lifter group.
b. Remove the camshaft.
1/4
352F XE Excavator MDR00001-UP (MACHINE) POWERED BY C13 Engine(M007...
2020/10/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...