The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like the head assembly, brake housing, barrel assembly, and more. It also includes 13 steps for reassembly, applying lubricants and installing components like the actuator piston, seals, bearing races, barrel assembly, and more. Precise torques and specifications are provided for numerous component installations.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349E and 349E L Excavator (Prefix RGH) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar Cat 349E L Excavator (Prefix RGH) Service Repair Manual (RGH00001...jdksmmdmdd
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar Cat 349E and 349E L Excavator (Prefix RGH) Service Repair Manual ...f8uejkdkdmm3e
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. It describes in detail the 27 steps to disassemble the motor, removing components like the head assembly, brake housing, rotating group, barrel assembly, and more. It then lists the required tools and specifications and describes the 25 steps to reassemble the motor, providing illustrations to show how to install components like the actuator piston, seals, bearing races, barrel assembly, pistons, and more.
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. It includes 27 steps for disassembly, removing components like the head assembly, brake housing, rotating group and individual parts within these assemblies. The assembly section includes 13 steps and specifications for reinstalling components and torquing fasteners, ensuring parts like seals and springs meet specifications. The goal is to properly disassemble and reassemble the travel motor while following all safety precautions.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349E and 349E L Excavator (Prefix RGH) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar Cat 349E L Excavator (Prefix RGH) Service Repair Manual (RGH00001...jdksmmdmdd
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar Cat 349E and 349E L Excavator (Prefix RGH) Service Repair Manual ...f8uejkdkdmm3e
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. It describes in detail the 27 steps to disassemble the motor, removing components like the head assembly, brake housing, rotating group, barrel assembly, and more. It then lists the required tools and specifications and describes the 25 steps to reassemble the motor, providing illustrations to show how to install components like the actuator piston, seals, bearing races, barrel assembly, pistons, and more.
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. It includes 27 steps for disassembly, removing components like the head assembly, brake housing, rotating group and individual parts within these assemblies. The assembly section includes 13 steps and specifications for reinstalling components and torquing fasteners, ensuring parts like seals and springs meet specifications. The goal is to properly disassemble and reassemble the travel motor while following all safety precautions.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...f89siekkmdmm2w
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are included to properly release spring forces and avoid damaging mating surfaces. Tools required include an eyebolt, retaining ring pliers, bearing puller, and adapter to securely hold parts during disassembly and assembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...f89siekkmdmm2w
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components.
4. Cleanliness is emphasized as important during both disassembly and assembly to prevent dirt from damaging internal parts.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...f89siekkmdmm2w
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
The document provides instructions for removing and installing a cab on a 336 excavator. It lists required tools including eyebolts. Steps include removing the air cleaner mount first. Various illustrations show disconnecting wiring harnesses and brackets, and lifting the cab off using the eyebolts. Reinstallation follows the removal steps in reverse order.
The document provides instructions for disassembling and assembling the final drive of a 336 Excavator. It lists 24 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 29 steps for assembly, installing components in reverse order and noting specifics like torque values and tooling used. Precise assembly is emphasized, including bearing installation and shim thickness measurement to set proper backlash.
The document provides instructions for removing and installing various engine components on a Caterpillar 336 Excavator including the lifter group, camshaft, camshaft gear, camshaft bearings, and engine oil pan. The instructions include lists of required tools and multi-step procedures accompanied by illustrations of each step. Safety notices are also provided throughout the document.
Caterpillar Cat 336D and 336D L Excavator (Prefix M3N) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves removing all grease, marking the swing gear and bearing and frame for alignment, attaching lifting tools, and using a hydraulic torque wrench to remove bolts and spacers. The swing gear and bearing assembly weighs approximately 280 kg and must be lifted carefully after the bolts are removed.
Caterpillar Cat 335F and 335F L Excavator (Prefix SGJ) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor on a 335F excavator model. The disassembly process involves removing 27 different components from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and tightening bolts to the correct torque specifications.
The document provides instructions for removing and installing components on a 336 excavator, including the operator monitor, hydraulic lockout control, and piston motor. It lists the required tools and includes illustrations showing the component locations and step-by-step removal and installation procedures. Safety warnings are provided to prevent injury when working with spring loaded parts. The document also identifies the excavator model and powered engine to ensure the correct repair manual is referenced.
The document is a service repair manual that provides instructions for connecting and disconnecting various components of an excavator model 336. It includes:
1) A list of required tools and replacement parts for the procedures.
2) Step-by-step illustrated instructions for connecting components like the hydraulic pump, boom cylinder, and undercarriage frame.
3) Directions for draining fluids like oil from the final drive before disconnecting it.
4) Notes on installation being the reverse of removal steps and requirements like torquing nuts to specification.
Caterpillar Cat 330F and 330F LN Excavator (Prefix HBT) Service Repair Manual...f89siekkmdmm2w
This document provides instructions for removing and installing components related to the crankshaft and front cover of a Caterpillar 330F excavator engine. The procedures include removing and installing the crankshaft pulley, vibration damper, front seal, and heavy duty front cover. Tools required are listed for each procedure. Illustrations show the components and steps to disassemble and reassemble the assemblies.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix FEX) Service Repair Manua...f89siekkmdmm2w
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components weighing up to 550 kg during disassembly. Cleanliness is important to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have additional assistance when removing heavier parts weighing over 30 kg. The detailed process takes the final drive completely apart down to individual planetary gears and shafts.
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble components like pistons, gears, brackets, hoses and sensors. Tools include lever pullers, link brackets and torque wrenches. Precautions are given for spring loaded parts. The process involves lifting heavy pump assemblies into place and tightening hundreds of bolts and fittings to specified torques.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Proper cleaning, containment of fluids, and use of anti-seize coating are emphasized to prevent contamination.
Caterpillar Cat 330D and 330D L Excavator (Prefix NBD) Service Repair Manual ...f89siekkmdmm2w
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f89siekkmdmm2w
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It lists the required tools and presents step-by-step procedures for removing and installing each component of the travel motor. Some key steps include removing the head from the motor body, taking apart the rotating assembly, and disassembling the brake piston. Special care must be taken to avoid damaging parts and ensure proper alignment during reassembly.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...f89siekkmdmm2w
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are included to properly release spring forces and avoid damaging mating surfaces. Tools required include an eyebolt, retaining ring pliers, bearing puller, and adapter to securely hold parts during disassembly and assembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...f89siekkmdmm2w
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components.
4. Cleanliness is emphasized as important during both disassembly and assembly to prevent dirt from damaging internal parts.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...f89siekkmdmm2w
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
The document provides instructions for removing and installing a cab on a 336 excavator. It lists required tools including eyebolts. Steps include removing the air cleaner mount first. Various illustrations show disconnecting wiring harnesses and brackets, and lifting the cab off using the eyebolts. Reinstallation follows the removal steps in reverse order.
The document provides instructions for disassembling and assembling the final drive of a 336 Excavator. It lists 24 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 29 steps for assembly, installing components in reverse order and noting specifics like torque values and tooling used. Precise assembly is emphasized, including bearing installation and shim thickness measurement to set proper backlash.
The document provides instructions for removing and installing various engine components on a Caterpillar 336 Excavator including the lifter group, camshaft, camshaft gear, camshaft bearings, and engine oil pan. The instructions include lists of required tools and multi-step procedures accompanied by illustrations of each step. Safety notices are also provided throughout the document.
Caterpillar Cat 336D and 336D L Excavator (Prefix M3N) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves removing all grease, marking the swing gear and bearing and frame for alignment, attaching lifting tools, and using a hydraulic torque wrench to remove bolts and spacers. The swing gear and bearing assembly weighs approximately 280 kg and must be lifted carefully after the bolts are removed.
Caterpillar Cat 335F and 335F L Excavator (Prefix SGJ) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor on a 335F excavator model. The disassembly process involves removing 27 different components from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and tightening bolts to the correct torque specifications.
The document provides instructions for removing and installing components on a 336 excavator, including the operator monitor, hydraulic lockout control, and piston motor. It lists the required tools and includes illustrations showing the component locations and step-by-step removal and installation procedures. Safety warnings are provided to prevent injury when working with spring loaded parts. The document also identifies the excavator model and powered engine to ensure the correct repair manual is referenced.
The document is a service repair manual that provides instructions for connecting and disconnecting various components of an excavator model 336. It includes:
1) A list of required tools and replacement parts for the procedures.
2) Step-by-step illustrated instructions for connecting components like the hydraulic pump, boom cylinder, and undercarriage frame.
3) Directions for draining fluids like oil from the final drive before disconnecting it.
4) Notes on installation being the reverse of removal steps and requirements like torquing nuts to specification.
Caterpillar Cat 330F and 330F LN Excavator (Prefix HBT) Service Repair Manual...f89siekkmdmm2w
This document provides instructions for removing and installing components related to the crankshaft and front cover of a Caterpillar 330F excavator engine. The procedures include removing and installing the crankshaft pulley, vibration damper, front seal, and heavy duty front cover. Tools required are listed for each procedure. Illustrations show the components and steps to disassemble and reassemble the assemblies.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix FEX) Service Repair Manua...f89siekkmdmm2w
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components weighing up to 550 kg during disassembly. Cleanliness is important to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have additional assistance when removing heavier parts weighing over 30 kg. The detailed process takes the final drive completely apart down to individual planetary gears and shafts.
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble components like pistons, gears, brackets, hoses and sensors. Tools include lever pullers, link brackets and torque wrenches. Precautions are given for spring loaded parts. The process involves lifting heavy pump assemblies into place and tightening hundreds of bolts and fittings to specified torques.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Proper cleaning, containment of fluids, and use of anti-seize coating are emphasized to prevent contamination.
Caterpillar Cat 330D and 330D L Excavator (Prefix NBD) Service Repair Manual ...f89siekkmdmm2w
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f89siekkmdmm2w
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It lists the required tools and presents step-by-step procedures for removing and installing each component of the travel motor. Some key steps include removing the head from the motor body, taking apart the rotating assembly, and disassembling the brake piston. Special care must be taken to avoid damaging parts and ensure proper alignment during reassembly.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR SPG
Configuration: 349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator Machine Systems
Media Number -KENR9848-04 Publication Date -01/10/2012 Date Updated -23/10/2012
i04243909
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B - Bolt M4 x 0.7 1
C 6V-3010 Puller Gp 1
D 3E-3879 Eyebolt 1
E 9S-9152 Bearing Puller Gp 1
Start By:
a. Remove the travel motor.
1. Drain the travel motor.
1/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02419258
2. Remove O-ring seal (1) from motor housing (2).
Illustration 2 g02419296
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Attach Tooling (A) onto head assembly (3). Remove bolts (4). Use Tooling (A) and a
suitable lifting device to remove head (3). The weight of head assembly (3) is
approximately 40 kg (90 lb).
2/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02419358
4. Remove plate (5) from head (3).
Illustration 4 g02419359
5. Remove bearing (6) from head assembly (3).
6. Remove orifice (7), spring (8), and ball (9).
7. Remove O-ring seal (10) from head assembly (3).
Illustration 5 g02419416
3/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove adapter (11), spool (12), and spring (13) from head assembly (3).
Illustration 6 g02419439
9. Use Tooling (B) in order to remove retainers (14) from head assembly (3).
10. Remove O-ring seals (16) and backup rings (15) from adapters (14).
11. Remove balls (17) from head assembly (3).
Illustration 7 g02419577
12. Remove springs (18) from brake housing (20).
4/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 13. Remove O-ring seals (19) from motor housing (2).
Illustration 8 g02420880
14. Use Tooling (C) in order to remove brake housing (20) from motor housing (2).
Illustration 9 g02419659
15. Remove backup ring (21) and O-ring seal (22) from brake piston (20).
16. Remove O-ring seal (23) and backup ring (24) from brake piston (20).
5/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g02419858
17. Attach Tooling (D) to shaft assembly (25).
18. Use Tooling (D) and a suitable lifting device in order to lift the rotating group from motor
housing (2). The weight of the rotating group is approximately 30 kg (65 lb).
Illustration 11 g02420501
19. Remove plates (26) and friction disks (27) from barrel assembly (28).
6/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g02420544
20. Remove barrel assembly (28) and swashplate (29) from shaft assembly (25).
Illustration 13 g02420578
21. Remove plate (31) and pistons (30) from barrel assembly (28).
7/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g02420596
22. Remove bearing (32), thin shim (33), Belleville washers (34), and barrel spacer (35) from
barrel assembly (28).
Illustration 15 g02420937
23. Use a suitable press in order to remove bearing (36) from shaft assembly (25).
8/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g02421036
24. Use Tooling (E) and a suitable press in order to remove inner race (37) from shaft assembly
(25).
Illustration 17 g02420998
Illustration 18 g02421000
9/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 25. Remove keys (38) and pins (39) from motor housing (2).
Illustration 19 g02421056
26. Remove plug (40) and the O-ring seal. Remove actuator piston (41).
27. Remove retaining ring (42) and seal (43) from motor housing (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 18 01:33:47 UTC+0800 2020
10/10
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR SPG
Configuration: 349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator Machine Systems
Media Number -KENR9848-04 Publication Date -01/10/2012 Date Updated -23/10/2012
i06563923
Travel Motor - Assemble
SMCS - 4351-016
Specifications
Illustration 1 g03845362
NOTICE
To prevent damage to the motor, the case must be filled with clean
hydraulic oil at least to the fill port before operation.
1/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Table 1
Specification for 390-1088 Travel Motor Gp
Item Qty Part Specification Description
1 1 5P-7684 Plug Torque to 430 ± 40 N·m (317 ± 30 lb ft).
2 1
6K-6307 O-
Ring Seal
Lubricate with 1U-6396 O-Ring Assembly Compound.
- - -
Before assembly, lubricate the sliding surfaces of the cam plate
(3), the hold-down (4), the pistons (5), the barrel (6) and the shaft
(8) lightly with clean hydraulic oil.
7 20
124-1561 Brake
Spring
Length under test force is 19.0 mm (0.75 inch).
Test force is 425 ± 43 N (96 ± 10 lb).
Free length after test is 22.06 mm (0.869 inch).
9 1
6V-3382 Lip
Type Seal
Apply blue Loctite 243 to the outside diameter.
10 1
118-5805
Special Race
Bearing
Install the snap ring of the special race bearing toward the shaft
flange.
11 2
9S-4185 O-
Ring Plug
Torque to 82 ± 8 N·m (60 ± 6 lb ft).
12 6 8T-4187 Bolt Torque to 530 ± 70 N·m (391 ± 52 lb ft).
13 2
9S-4183 O-
Ring Plug
Torque to 190 ± 20 N·m (140 ± 15 lb ft).
Illustration 2 g03845364
Section A-A
Table 2
2/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Item Qty Part Specification Description
14 2
1T-0936 Pipe
Plug
Install in the orifice toward the head surface or below the head
surface.
15 1 124-1554 Spring
Length under test force is 15 mm (0.6 inch).
Test force is 15.0 ± 2.0 N (3.4 ± 0.4 lb).
Free length after test is 16.15 mm (0.636 inch).
D - -
Depth from the head and interface of the port plate is
20.0 ± 0.2 mm (0.79 ± 0.01 inch).
16 1
195-4456 Orifice
Plug
Torque to 7 ± 1 N·m (62 ± 9 lb in).
Illustration 3 g03845365
Section C-C
Table 3
Item Qty Part Specification Description
17 1 230-5483 Spring
Length under test force is 25 mm (1.0 inch).
Test force is 60.0 ± 8.0 N (13.5 ± 1.8 lb).
Free length after test is 35 mm (1.4 inch).
18 1 087-4786 Adapter Torque to 115 ± 10 N·m (85 ± 7 lb ft).
Assembly Procedure
Table 4
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
D 3E-3879 Eyebolt 1
3/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. F 1U-6396 O-Ring Assembly Compound 1
G - Loctite 242 -
H 1P-0510 Driver Gp 1
J 6V-2055 Grease 1
K 128-5049 Guide Stud 2
Illustration 4 g02421056
1. Lubricate actuator piston (41) with the oil that is being used. Install actuator piston (41) into
housing (2). Apply Tooling (F) onto O-ring seal of plug (40). Install plug (40) into motor
housing (2).Tighten plug (42) to a torque of 430 ± 40 N·m (315 ± 30 lb ft).
2. Apply Tooling (G) onto outside diameter of seal (43). Use Tooling (H) to install seal (43).
Install retaining ring (42).
Illustration 5 g02421000
4/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g02420998
3. Install pins (39) and keys (38) into motor housing (2).
Illustration 7 g02421876
Illustration 8 g02421958
4. Use a suitable press to install bearing (36) and bearing (37) onto shaft assembly (25). Bearing
(36) must be installed with Retaining Clip (X) toward the barrel assembly.
5/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g02423621
8. Use Tooling (D) and a suitable lifting device to install the rotating group into motor housing
(2). The weight of the rotating group is approximately 30 kg (65 lb).
Note: Align the notches of swashplate (29) with the keys in the motor housing (2).
Note: Protect shaft seal (43) from damage by covering the splines on shaft assembly (25) with
heat shrink tubing.
Illustration 14 g02423738
8/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g02423742
9. Install plates (26) and friction discs (27). Start with plate (26). Alternate between plates (26)
and friction discs (27) with plates (26) on the top and the bottom.
Illustration 16 g02419659
10. Install backup ring (21) and O-ring seal (22) onto brake piston (20).
11. Install backup ring (24) and O-ring seal (23) onto brake piston (20).
Illustration 17 g02419577
12. Install O-ring seals (19) onto motor housing (2). Install springs (18) onto brake piston (20).
9/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g02419439
13. Install balls (17), backup rings (15), O-ring seals (16), and retainers (14) into head assembly
(3).
Illustration 19 g02419416
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install spring (13), spool (12), and adapter (11). Tighten adapter (11) to a torque of
115 ± 10 N·m (85 ± 7 lb ft).
10/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g02419359
15. Install ball (9), spring (8), and orifice (7). Tighten orifice (7) to a torque of 7 ± 1 N·m
(62 ± 9 lb in).
16. Install bearing (6) and O-ring seal (10) onto head assembly (3).
Illustration 21 g02001974
Illustration 22 g02419358
17. Apply Tooling (K) to the back side of plate (5) to hold plate (5) in place during assembly.
Install plate (5) to head assembly (3).
11/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 23 g02424459
Illustration 24 g02419296
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
18. Install Tooling (K) onto motor housing (2). Use Tooling (A) and a suitable lifting device to
install head assembly (3) onto motor housing (2).The weight of the head (3) is approximately
40 kg (90 lb). Remove Tooling (A) and Tooling (D). Install bolts (4). Tighten bolts (4) to a
torque of 530 ± 70 N·m (390 ± 50 lb ft).
12/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 25 g02419258
19. Install O-ring seal (1) onto motor housing (2).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 18 01:34:43 UTC+0800 2020
13/13
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR SPG
Configuration: 349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator Machine Systems
Media Number -KENR9848-04 Publication Date -01/10/2012 Date Updated -23/10/2012
i07186913
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3941 Link Brackets 2
C - Loctite 243 -
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/4
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 1 g02415557
2. Release the track tension. Refer to Operation and Maintenance Manual, "Track Adjustment
- Adjust".
3. Start the machine. Position track roller (1) on suitable cribbing. Position pin to separate the
track above the final drive.
4. Separate the track.
5. Remove the counterbalance valve.
Illustration 2 g02417799
2/4
349E & 349E L Excavators SPG00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/9/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...