This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. The disassembly process involves removing 22 components from the fan drive including bolts, retainers, seals, discs, plates, and bearings. The assembly process is the reverse and includes applying sealant and installing the components in the proper order and orientation using various tools. Special care must be taken when handling springs and seals. Cleanliness is important to prevent contamination.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual clutch components like discs and plates are removed. Reassembly involves reversing the disassembly steps and carefully reinstalling components like bearings, seals, springs, and retainers in the proper order and orientation. Precautions are outlined to prevent damage and contain fluids.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...yinranhe0814
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include:
1. Removing components like the sensor, retainer, O-rings, drive flange, and clutch housing assembly.
2. Separating the cover assembly from the case and removing internal components like seals, bearings, plates, and springs.
3. Dismantling the shaft assembly by removing seals, sleeves, and retainers.
4. Reassembling follows the reverse order, taking care to clean parts and replace worn components using the provided tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...wfu089267
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and bearings from the drive flange, cover assembly, case, clutch housing, and shaft assembly. The assembly procedure outlines installing these components in reverse order and notes that cleanliness is important to prevent damage to precision parts. Special care must be taken when handling spring-loaded or sealed parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual parts like bearings, seals, springs, and discs are removed or installed. Precautions are outlined to prevent damage and contain fluids. The assembly procedure reverses the disassembly steps and notes to clean parts and apply sealants in the proper locations.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f89siekkmdmm2w
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 17 components including bolts, retainers, seals, and shafts using various tools.
3) The assembly process reverses the disassembly steps and provides notes on cleaning, inspecting, and applying sealant to parts during reassembly.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f8uejkdkdmm3e
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly follows the reverse order, applying sealant and pressing components back together using various tools. Proper cleaning and inspection of parts is emphasized.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. The disassembly process involves removing 22 components from the fan drive including bolts, retainers, seals, discs, plates, and bearings. The assembly process is the reverse and includes applying sealant and installing the components in the proper order and orientation using various tools. Special care must be taken when handling springs and seals. Cleanliness is important to prevent contamination.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual clutch components like discs and plates are removed. Reassembly involves reversing the disassembly steps and carefully reinstalling components like bearings, seals, springs, and retainers in the proper order and orientation. Precautions are outlined to prevent damage and contain fluids.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...yinranhe0814
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include:
1. Removing components like the sensor, retainer, O-rings, drive flange, and clutch housing assembly.
2. Separating the cover assembly from the case and removing internal components like seals, bearings, plates, and springs.
3. Dismantling the shaft assembly by removing seals, sleeves, and retainers.
4. Reassembling follows the reverse order, taking care to clean parts and replace worn components using the provided tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...wfu089267
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and bearings from the drive flange, cover assembly, case, clutch housing, and shaft assembly. The assembly procedure outlines installing these components in reverse order and notes that cleanliness is important to prevent damage to precision parts. Special care must be taken when handling spring-loaded or sealed parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. Key steps include using various tools to remove components like bolts, retainers, seals, and plates. The drive flange, cover assembly, and clutch housing assembly are then separated from the case. Individual parts like bearings, seals, springs, and discs are removed or installed. Precautions are outlined to prevent damage and contain fluids. The assembly procedure reverses the disassembly steps and notes to clean parts and apply sealants in the proper locations.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f89siekkmdmm2w
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 17 components including bolts, retainers, seals, and shafts using various tools.
3) The assembly process reverses the disassembly steps and provides notes on cleaning, inspecting, and applying sealant to parts during reassembly.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual Instant D...f8uejkdkdmm3e
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly follows the reverse order, applying sealant and pressing components back together using various tools. Proper cleaning and inspection of parts is emphasized.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document is a service repair manual that provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and begins by having the transmission removed and installed on an engine stand. It then provides step-by-step instructions to disassemble the various transmission components including removing gears, shafts, seals, and other parts. Detailed illustrations accompany each step.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 430E backhoe loader. It lists the required tools and presents the steps in detail with illustrations. The removal procedure involves removing bolts and lowering the guard with a hydraulic jack to access the drive shaft. Installation is the reverse of removal.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housing in their proper order and orientation. Tolerances for shaft play are also specified to be checked with gauges during assembly. The transmission is then mounted to the vehicle and electrical and hydraulic connections are made.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, seals and housing in their proper order and orientation. Tools required for the assembly are listed. Precautions like applying transmission oil and heating bearings to the specified temperature before installation are mentioned. Final steps include installing the transmission in the vehicle and connecting related components.
The document provides instructions for disassembling the transmission of a 420F2 backhoe loader. It describes removing over 20 components from the transmission, including the torque converter, gears, shafts, bearings, seals and other parts. Safety warnings are included to release springs carefully and wear protective equipment. Detailed illustrations accompany each step. The goal is to fully disassemble the transmission down to its individual parts for repair or replacement.
The document provides instructions for assembling a 424D backhoe loader transmission. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housings. It also provides details on final assembly steps, which include applying sealant, installing the transmission case and shafts, and connecting electrical connectors. Tolerances for shaft play are specified to be checked with a dial indicator during assembly.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 422E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard while removing bolts and lowering the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening bolts to the specified torque.
4) Raising and securing the drive shaft guard with new bolts after installation is complete.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. The 18 steps listed to install the engine describe reconnecting wiring, replacing mounting hardware, refilling fluids, and reinstalling removed components. The document is a service repair manual that details the process to remove and install an engine on the specified backhoe loader model.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, connect related components like the transmission, alternator, and air conditioning, and refill fluids before completing reassembly. Tools including a hydraulic jack and load leveling beam are required. Proper installation ensures the engine operates safely and efficiently.
The document provides instructions for removing and installing the flywheel housing on a 422E Backhoe Loader. To remove the housing, the flywheel must first be removed. Bolts are then removed from the housing and it is lifted off using a device. When installing, dowels and seals are inspected, bolts are used to secure the housing, and torque specifications are provided. The process is intended to provide maintenance for the flywheel housing component.
This document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a Caterpillar 420F2 backhoe loader with a C4.4 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe how to remove the existing crankshaft rear seal and flywheel housing, clean and inspect components, install a new seal and gasket, and reinstall the housing while torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
This document provides instructions for installing an engine in a 416F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, including connecting various components like the transmission, electrical harnesses, air conditioning compressor, and fuel and cooling systems. Proper installation of the engine is critical for safe and reliable operation of the backhoe loader.
The document provides instructions for disassembling the transmission of a 416E Backhoe Loader. It lists required tools and gives step-by-step instructions with illustrations. Key steps include removing the transmission from the vehicle, then disassembling its major components such as pumps, shafts, gears, seals and housing. Specific instructions are provided for disassembling the front and rear output shafts. Safety precautions are noted for releasing spring forces. The goal is to fully disassemble the transmission into its core components.
1. The document provides instructions for removing and installing various engine components on a Caterpillar 416F2 backhoe loader, including lifters, camshafts, camshaft bearings, and piston cooling jets.
2. The procedures describe using specialized tools to remove parts and ensuring parts are clean before installation.
3. Technicians are advised to mark lifters during removal for correct installation and lubricate parts with oil before reinstallation.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document is a service repair manual that provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and begins by having the transmission removed and installed on an engine stand. It then provides step-by-step instructions to disassemble the various transmission components including removing gears, shafts, seals, and other parts. Detailed illustrations accompany each step.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 430E backhoe loader. It lists the required tools and presents the steps in detail with illustrations. The removal procedure involves removing bolts and lowering the guard with a hydraulic jack to access the drive shaft. Installation is the reverse of removal.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housing in their proper order and orientation. Tolerances for shaft play are also specified to be checked with gauges during assembly. The transmission is then mounted to the vehicle and electrical and hydraulic connections are made.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, seals and housing in their proper order and orientation. Tools required for the assembly are listed. Precautions like applying transmission oil and heating bearings to the specified temperature before installation are mentioned. Final steps include installing the transmission in the vehicle and connecting related components.
The document provides instructions for disassembling the transmission of a 420F2 backhoe loader. It describes removing over 20 components from the transmission, including the torque converter, gears, shafts, bearings, seals and other parts. Safety warnings are included to release springs carefully and wear protective equipment. Detailed illustrations accompany each step. The goal is to fully disassemble the transmission down to its individual parts for repair or replacement.
The document provides instructions for assembling a 424D backhoe loader transmission. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housings. It also provides details on final assembly steps, which include applying sealant, installing the transmission case and shafts, and connecting electrical connectors. Tolerances for shaft play are specified to be checked with a dial indicator during assembly.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 422E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard while removing bolts and lowering the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening bolts to the specified torque.
4) Raising and securing the drive shaft guard with new bolts after installation is complete.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. The 18 steps listed to install the engine describe reconnecting wiring, replacing mounting hardware, refilling fluids, and reinstalling removed components. The document is a service repair manual that details the process to remove and install an engine on the specified backhoe loader model.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, connect related components like the transmission, alternator, and air conditioning, and refill fluids before completing reassembly. Tools including a hydraulic jack and load leveling beam are required. Proper installation ensures the engine operates safely and efficiently.
The document provides instructions for removing and installing the flywheel housing on a 422E Backhoe Loader. To remove the housing, the flywheel must first be removed. Bolts are then removed from the housing and it is lifted off using a device. When installing, dowels and seals are inspected, bolts are used to secure the housing, and torque specifications are provided. The process is intended to provide maintenance for the flywheel housing component.
This document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a Caterpillar 420F2 backhoe loader with a C4.4 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe how to remove the existing crankshaft rear seal and flywheel housing, clean and inspect components, install a new seal and gasket, and reinstall the housing while torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
This document provides instructions for installing an engine in a 416F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, including connecting various components like the transmission, electrical harnesses, air conditioning compressor, and fuel and cooling systems. Proper installation of the engine is critical for safe and reliable operation of the backhoe loader.
The document provides instructions for disassembling the transmission of a 416E Backhoe Loader. It lists required tools and gives step-by-step instructions with illustrations. Key steps include removing the transmission from the vehicle, then disassembling its major components such as pumps, shafts, gears, seals and housing. Specific instructions are provided for disassembling the front and rear output shafts. Safety precautions are noted for releasing spring forces. The goal is to fully disassemble the transmission into its core components.
1. The document provides instructions for removing and installing various engine components on a Caterpillar 416F2 backhoe loader, including lifters, camshafts, camshaft bearings, and piston cooling jets.
2. The procedures describe using specialized tools to remove parts and ensuring parts are clean before installation.
3. Technicians are advised to mark lifters during removal for correct installation and lubricate parts with oil before reinstallation.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i05239586
Fan Drive - Disassemble - Hydraulic Fan Drive
SMCS - 1359-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 9U-7480 Compressing Tube 1
C 1P-1859 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
Start By:
a. Remove the Hydraulic fan Drive. Refer to Disassembly and Assembly, "Fan Drive -
Remove and Install".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, thoroughly
clean the exterior of the components. This procedure will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01208862
1. Remove bolt (2) and sensor (1).
Illustration 2 g01333292
2. Remove bolts (3). Remove retainer (4).
2/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01333295
Illustration 4 g02089003
3. Remove O-ring seal (5) and drive flange (6).
4. Firmly secure drive flange (6) with a suitable vise. Protect drive flange (6) in order to
prevent damage during clamping.
5. Use a hammer and a chisel in order to break sleeve (6A). Use extreme care to prevent
damage to drive flange (6).
3/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01208866
6. Remove bolts (7). Separate cover assembly (8) from case (9).
Illustration 6 g01333297
7. Position cover assembly (8) on the opposite side.
8. Remove O-ring seal (10) from cover assembly (8).
Illustration 7 g01208919
9. Use a suitable press in order to separate cover assembly (8) and clutch housing assembly
(11).
4/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01258470
10. Remove lip seal (12). Use Tooling (A) in order to remove retaining ring (13). Use a suitable
press in order to remove bearing (14).
Illustration 9 g01208920
Note: Note the order of all the components in the clutch assembly.
11. Remove retaining ring (15). Remove retaining plate (16). Remove discs and clutch plates
(17).
Illustration 10 g01333298
5/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Use Tooling (B) and a suitable press to reposition piston (18). Use Tooling (C) in order to
remove retaining ring (19). Remove piston (18).
Illustration 11 g01333300
13. Remove seal (20) from piston (18).
Illustration 12 g01333301
14. Remove spring (21) from clutch housing assembly (11).
6/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g01333303
15. Remove seal rings (22) from shaft assembly (24). Use Tooling (D) in order to remove
retaining ring (23).
Illustration 14 g02089058
16. Use a suitable press in order to remove shaft assembly (24) from case (9).
Illustration 15 g02089073
17. Remove seal (25) from shaft assembly (24).
7/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 18. Firmly secure shaft assembly (24) with a suitable vise. Protect shaft assembly (24) in order
to prevent damage during clamping.
19. Use a hammer and a chisel in order to break sleeve (30). Use extreme care to prevent
damage to shaft assembly (24).
Illustration 16 g01333308
20. Remove tube assembly (26) from case (9).
Illustration 17 g01333310
21. Remove lip seal (27) from case (9).
8/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g01333314
22. Use Tooling (A) in order to remove retaining ring (28). Use a suitable press in order to
remove bearing (29) from case (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:54:22 UTC+0800 2020
9/9
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142230
Fan Drive - Disassemble - Direct Drive
SMCS - 1359-015
Disassembly Procedure
Start By:
A. Remove the fan drive (direct drive).
Illustration 1 g02341528
1. Remove bolt (8), plate (7), bearing assembly (5), hub assembly (4), spacer (3), and bearing
assembly (2) from bracket assembly (1) .
2. Remove spring pin (6) from plate (7) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:55:17 UTC+0800 2020
1/2
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i06192451
Fan Drive - Assemble - Hydraulic Fan Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 9U-7480 Compressing Tube 1
C 1P-1859 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
E - Loctite Flexible Anaerobic Gasket Flange 1
F - Loctite 648 1
G 359-4915 Driver 1
H 359-4916 Driver 1
Note: Caution is required while handling the lip seals. The lip seals can be damaged if objects or
cleaning fluids contact the sealing surface.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts except the lip
seals with cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to
dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01333314
1. Use a suitable press to install bearing (29) into case (9) . Use Tooling (A) in order to install
retaining ring (28) .
Illustration 2 g01333310
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
2. Apply Tooling (E) to the outside diameter of lip seal (27) . Carefully install lip seal (27) into
case (9) .
2/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g02092525
3. Install seal (25) onto shaft assembly (24) .
4. Apply Tooling (F) to the full diameter of the shoulder on shaft assembly (24) . Position new
sleeve (30) on shaft assembly (24) . The external chamfer on sleeve (30) will be on top. Use
Tooling (G) and a suitable press in order to install sleeve (30) . Remove excess Tooling (F) .
Illustration 4 g01333308
Illustration 5 g01286111
3/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5. Position tube assembly (26) into case (9) .
6. Position case (9) and tube assembly (26) onto shaft assembly (24) .
7. Use a suitable press and a suitable driver to press shaft assembly (24) through the bearing
and through tube assembly (26) .
Illustration 6 g01333303
8. Use Tooling (D) in order to install retaining ring (23) . Install seal rings (22) onto shaft
assembly (24) .
Illustration 7 g01333301
9. Install spring (21) on clutch housing assembly (11) .
4/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g01333300
10. Install seal (20) on piston (18) .
Illustration 9 g01333298
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Install piston (18) . Use Tooling (B) and a suitable press in order to position piston (18) .
Use Tooling (C) in order to install retaining ring (19) . Carefully release the tension on
Tooling (B) .
5/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g01208920
12. Install clutch plates (16) and discs (17) . Install retaining ring (15) .
Illustration 11 g01209073
13. Position cover assembly (8) onto clutch housing assembly (11) .
Note: Make sure that the splines of cover assembly (8) fully engage all of the clutch plates
and discs in the clutch assembly.
6/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 12 g01209125
Illustration 13 g01258534
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
14. Use a suitable press in order to install bearing (14) . Use Tooling (A) in order to install
retaining ring (13) . Install lip seal (12) .
Illustration 14 g01333297
15. Position cover assembly (8) on the opposite side.
16. Install O-ring seal (10) on cover assembly (8) .
7/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 15 g01208914
17. Position cover assembly (8) onto case (9) . Install bolts (7) and tighten bolts (7) to a
minimum torque of 18 N·m (13 lb ft) up to a maximum torque of 31 N·m (23 lb ft).
Illustration 16 g02092935
18. Apply Tooling (F) to the full diameter of the shoulder on drive flange (6) . Position new
sleeve (6A) on drive flange (6) . The external chamfer on sleeve (6A) will be on top. Use
Tooling (H) and a suitable press in order to install sleeve (6A) . Remove excess Tooling
(F) .
8/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 17 g01333295
19. Install drive flange (6) and O-ring seal (5) .
Illustration 18 g01333292
20. Install retainer (4) . Tighten retainer (4) to a minimum torque of 610 N·m (450 lb ft) up to a
maximum torque of 750 N·m (550 lb ft). After achieving the torque range, overtighten
retainer (4) as needed in order to align the next position for locking screws (3) .
21. Install locking screws (3) and tighten locking screws (3) to a minimum torque of 7 N·m (62
lb in) to a maximum torque of 10 N·m (89 lb in).
9/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 19 g01208862
22. Position sensor (1) . Install bolt (2) .
End By: Install the fan clutch. Refer to Disassembly and Assembly, "Fan Clutch - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:56:13 UTC+0800 2020
10/10
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engin...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142231
Fan Drive - Assemble - Direct Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Illustration 1 g02341528
1. Install spring pin (6) into plate (7) .
2. Apply Tooling (A) to the threads of bolt (8). Install bearing assembly (2), spacer (3), hub
assembly (4), bearing assembly (5), plate (7), and bolt (8) onto bracket assembly (1).
Tighten bolt (8) to a torque of 115 ± 15 N·m (85 ± 11 lb ft).
1/2
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. End By: Install the fan drive (direct drive).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 23:57:09 UTC+0800 2020
2/2
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E EXCAVATOR FJB
Configuration: 349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04108512
Water Pump - Remove and Install
SMCS - 1361-010; 1361-011; 1361-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Start By:
A. Remove the water temperature regulator.
B. Remove fan drive.
Illustration 1 g02310883
1/4
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. 1. Remove bolts (1) and sheet assembly (2). Remove bolts (3) and sheet assembly (4) .
Illustration 2 g02311921
2. Remove step (6), sheet assembly (5), sheet assembly (7), and sheet assembly (8) .
Illustration 3 g02311923
Note: Open the hoods to the FULLY OPEN position.
3. Disconnect support assembly (9). Use suitable cribbing to support the support assembly (9) .
4. Remove support assembly (10) and support assembly (11) .
2/4
349E & 349E L Excavators FJB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...