This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...zatao0179249295
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening to specified torques. Tools required are listed for each procedure.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...yinranhe0814
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening bolts to the specified torque. Tools required are listed for each procedure.
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
5. Installing the crankshaft rear seal by cleaning, applying primer and retaining compound, and installing the seal.
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...wfu089267
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite to bolts, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts and the seal.
5. Installing the crankshaft rear seal by cleaning parts, applying primer and retaining compound, and installing the seal with bol
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...fjskekxcddmmme
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...hhfjksekmm
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1) Removing the rear gear group by removing several bolts, gears, seals, and bearings.
2) Removing the flywheel using lifting equipment and special tools after removing mounting bolts.
3) Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4) Removing the crankshaft rear seal by removing mounting bolts.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...zatao0179249295
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening to specified torques. Tools required are listed for each procedure.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...yinranhe0814
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening bolts to the specified torque. Tools required are listed for each procedure.
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
5. Installing the crankshaft rear seal by cleaning, applying primer and retaining compound, and installing the seal.
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...wfu089267
This document provides instructions for removing and installing various components of a C13 engine, including:
1. Removing and installing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Installing the flywheel by heating the ring gear, attaching lifting tools, applying loctite to bolts, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts and the seal.
5. Installing the crankshaft rear seal by cleaning parts, applying primer and retaining compound, and installing the seal with bol
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...fjskekxcddmmme
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...hhfjksekmm
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1) Removing the rear gear group by removing several bolts, gears, seals, and bearings.
2) Removing the flywheel using lifting equipment and special tools after removing mounting bolts.
3) Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4) Removing the crankshaft rear seal by removing mounting bolts.
The document provides step-by-step instructions to disassemble the output transfer gears of a 745C Articulated Truck. It lists 49 steps to remove components like the output transfer gears case, yokes, seals, bearings, gears, shafts, and seals. Special tools are required to remove some components and safety precautions are provided given the heavy weight of some parts that need to be lifted.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
The document provides instructions for assembling and disassembling the piston pump used in Caterpillar 745 articulated trucks. The assembly instructions include installing various seals, springs, and other components in the proper order and orientation. Disassembly is performed by removing these same components in the reverse order. Pictures and diagrams accompany the text to illustrate each step. Safety warnings are provided to prevent injury from released spring forces during disassembly.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 740B Ejector Articulated Truck powered by a C15 engine. The removal procedure involves removing bolts and other components to detach the housing. For installation, the procedure describes cleaning parts, applying sealant, positioning seals and gears, and torquing bolts to specified values. Additional components like the rear power take-off must be removed before and reinstalled after the flywheel housing job.
This document provides disassembly instructions for the output transfer gears of a 740B articulated truck. It lists over 50 steps to remove various components such as planetary gears, shafts, seals, bearings, and housings. Special tools are required to remove some parts, and components can weigh up to 630 kg so lifting devices are needed. Detailed illustrations accompany each step to show the specific components and fasteners.
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing tooling to support the camshaft as it is slid out of the engine, being careful not to damage surfaces
4. Slowly sliding the camshaft forward and out of the engine using hooks for support, keeping it level throughout removal
The document provides instructions for installing the front cover on a C15 engine. It describes:
1. Cleaning the front housing sealing surface.
2. Installing a new seal into the front cover.
3. Positioning the front cover with installed seal on the front housing using alignment studs.
4. Installing spacers, nuts, and button head screws and tightening to the specified torque.
The document provides instructions for disassembling and assembling components of the gear pump and piston pump used in Caterpillar 740 GC articulated trucks. The gear pump section describes removing and installing the gear pump, housing, seals, gears, and other internal parts. The piston pump section outlines removing the pump head, springs, spools, pistons, bearings, and separating the rotating group from the pump housing. Detailed illustrations accompany each step to ensure safe and proper disassembly and reassembly of the pumps.
This document provides instructions for installing and removing the ejector blade carriage on a 740 Ejector Articulated Truck. It describes using lifting equipment and blocking to safely handle the 210 kg carriage component. The 10-step removal procedure includes loosening lock rings, bolts, and other hardware to separate the carriage from the machine. The 11-step installation procedure specifies replacing hardware in reverse order and adjusting components like floor rollers. Cleaning parts and noting shim positions are emphasized for correct reassembly.
The document provides instructions for disassembling a gear pump used in Caterpillar 740 articulated trucks. The disassembly procedure involves:
1. Removing fittings from the pump body and O-rings from the fittings.
2. Removing bolts securing a flange to the pump body and an O-ring from the flange.
3. Using retaining ring pliers to remove two rings from the flange and a lip seal from the flange.
The document provides instructions for removing and installing a steering cylinder on a 740 articulated truck. It lists the required tools which include chocks, a hydraulic cylinder tool, and washers. The steps include chocking the wheels, disconnecting grease lines if needed, and using a tool and washers to secure the rod end of the cylinder before removing mounting bolts and taking it off the vehicle. Reinstallation follows the removal steps in reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C15 engine, including:
1. Removing and installing the rear power take-off, which involves installing bushings and covers in the flywheel housing.
2. Removing and installing the vibration damper and pulley, which requires using tools to lift and position the components.
3. Procedures for removing and installing the crankshaft front seal, which includes using a slide hammer and seal installer tool.
The document contains detailed step-by-step instructions accompanied by illustrations and notes about keeping components clean and applying anti-seize compound as needed.
This document provides instructions for removing and installing various components of a C13 engine, including:
- The flywheel housing
- The vibration damper and pulley
- The crankshaft front seal
- The front cover
- The front gear group
- The front housing
- Accessory drive brackets and pulleys
- The fumes disposal filter
- The valve mechanism cover
The procedures include lists of required tools and step-by-step instructions for each removal and installation. Illustrations are provided to supplement the text instructions.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and disassembling a torque converter from a Caterpillar 730C2 articulated truck. It describes 18 steps to disassemble the torque converter and 19 steps to reassemble it. Tools required include an adapter plate, engine stand, oil drain cart, and link brackets. Safety precautions are provided to contain fluids and protect from spring forces.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing an engine from a 730C Ejector Articulated Truck. It outlines 25 steps to remove the engine, including disconnecting wiring harnesses, hoses, brackets and removing bolts. It then states the installation is done in reverse order. A second document provides instructions for releasing pressure from the hydraulic system before disassembly, including moving components and removing filler caps. A third document outlines 14 steps to disassemble a torque converter, including removing housing, rings, plates and discs.
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It describes 18 steps to disassemble the torque converter by removing housing assemblies, bearings, plates, discs, seals, and other components. It then describes 13 steps to assemble the torque converter by installing these same components in the reverse order, taking care to keep parts clean and follow procedures carefully due to parts that are spring loaded. Special tools are required for many steps, and safety precautions are provided.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 43 steps to assemble the torque converter components in the proper order, attaching seals, bearings, housings and other parts. It also provides illustrations matching each step. The final steps are to connect the assembled torque converter to the planetary transmission and lists the starting steps to remove the torque converter housing.
The document provides step-by-step instructions to disassemble the output transfer gears of a 745C Articulated Truck. It lists 49 steps to remove components like the output transfer gears case, yokes, seals, bearings, gears, shafts, and seals. Special tools are required to remove some components and safety precautions are provided given the heavy weight of some parts that need to be lifted.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
The document provides instructions for assembling and disassembling the piston pump used in Caterpillar 745 articulated trucks. The assembly instructions include installing various seals, springs, and other components in the proper order and orientation. Disassembly is performed by removing these same components in the reverse order. Pictures and diagrams accompany the text to illustrate each step. Safety warnings are provided to prevent injury from released spring forces during disassembly.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 740B Ejector Articulated Truck powered by a C15 engine. The removal procedure involves removing bolts and other components to detach the housing. For installation, the procedure describes cleaning parts, applying sealant, positioning seals and gears, and torquing bolts to specified values. Additional components like the rear power take-off must be removed before and reinstalled after the flywheel housing job.
This document provides disassembly instructions for the output transfer gears of a 740B articulated truck. It lists over 50 steps to remove various components such as planetary gears, shafts, seals, bearings, and housings. Special tools are required to remove some parts, and components can weigh up to 630 kg so lifting devices are needed. Detailed illustrations accompany each step to show the specific components and fasteners.
This document provides instructions for removing the camshaft from a Caterpillar C15 engine. The procedure involves:
1. Removing components like the camshaft gear and rocker arms
2. Removing bolts and plates connecting the camshaft to hold it in place
3. Installing tooling to support the camshaft as it is slid out of the engine, being careful not to damage surfaces
4. Slowly sliding the camshaft forward and out of the engine using hooks for support, keeping it level throughout removal
The document provides instructions for installing the front cover on a C15 engine. It describes:
1. Cleaning the front housing sealing surface.
2. Installing a new seal into the front cover.
3. Positioning the front cover with installed seal on the front housing using alignment studs.
4. Installing spacers, nuts, and button head screws and tightening to the specified torque.
The document provides instructions for disassembling and assembling components of the gear pump and piston pump used in Caterpillar 740 GC articulated trucks. The gear pump section describes removing and installing the gear pump, housing, seals, gears, and other internal parts. The piston pump section outlines removing the pump head, springs, spools, pistons, bearings, and separating the rotating group from the pump housing. Detailed illustrations accompany each step to ensure safe and proper disassembly and reassembly of the pumps.
This document provides instructions for installing and removing the ejector blade carriage on a 740 Ejector Articulated Truck. It describes using lifting equipment and blocking to safely handle the 210 kg carriage component. The 10-step removal procedure includes loosening lock rings, bolts, and other hardware to separate the carriage from the machine. The 11-step installation procedure specifies replacing hardware in reverse order and adjusting components like floor rollers. Cleaning parts and noting shim positions are emphasized for correct reassembly.
The document provides instructions for disassembling a gear pump used in Caterpillar 740 articulated trucks. The disassembly procedure involves:
1. Removing fittings from the pump body and O-rings from the fittings.
2. Removing bolts securing a flange to the pump body and an O-ring from the flange.
3. Using retaining ring pliers to remove two rings from the flange and a lip seal from the flange.
The document provides instructions for removing and installing a steering cylinder on a 740 articulated truck. It lists the required tools which include chocks, a hydraulic cylinder tool, and washers. The steps include chocking the wheels, disconnecting grease lines if needed, and using a tool and washers to secure the rod end of the cylinder before removing mounting bolts and taking it off the vehicle. Reinstallation follows the removal steps in reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C15 engine, including:
1. Removing and installing the rear power take-off, which involves installing bushings and covers in the flywheel housing.
2. Removing and installing the vibration damper and pulley, which requires using tools to lift and position the components.
3. Procedures for removing and installing the crankshaft front seal, which includes using a slide hammer and seal installer tool.
The document contains detailed step-by-step instructions accompanied by illustrations and notes about keeping components clean and applying anti-seize compound as needed.
This document provides instructions for removing and installing various components of a C13 engine, including:
- The flywheel housing
- The vibration damper and pulley
- The crankshaft front seal
- The front cover
- The front gear group
- The front housing
- Accessory drive brackets and pulleys
- The fumes disposal filter
- The valve mechanism cover
The procedures include lists of required tools and step-by-step instructions for each removal and installation. Illustrations are provided to supplement the text instructions.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and disassembling a torque converter from a Caterpillar 730C2 articulated truck. It describes 18 steps to disassemble the torque converter and 19 steps to reassemble it. Tools required include an adapter plate, engine stand, oil drain cart, and link brackets. Safety precautions are provided to contain fluids and protect from spring forces.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing an engine from a 730C Ejector Articulated Truck. It outlines 25 steps to remove the engine, including disconnecting wiring harnesses, hoses, brackets and removing bolts. It then states the installation is done in reverse order. A second document provides instructions for releasing pressure from the hydraulic system before disassembly, including moving components and removing filler caps. A third document outlines 14 steps to disassemble a torque converter, including removing housing, rings, plates and discs.
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It describes 18 steps to disassemble the torque converter by removing housing assemblies, bearings, plates, discs, seals, and other components. It then describes 13 steps to assemble the torque converter by installing these same components in the reverse order, taking care to keep parts clean and follow procedures carefully due to parts that are spring loaded. Special tools are required for many steps, and safety precautions are provided.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 43 steps to assemble the torque converter components in the proper order, attaching seals, bearings, housings and other parts. It also provides illustrations matching each step. The final steps are to connect the assembled torque converter to the planetary transmission and lists the starting steps to remove the torque converter housing.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06931709
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp. 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the electric starting motor.
b. Remove the flywheel.
1. Support the engine.
1/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g06002548
2. Remove bolts (2) and rear crankshaft seal (1).
Illustration 2 g06002556
3. Remove bolts (4) and the washers. Remove cover (3) and the seal.
Illustration 3 g06002558
4. Remove gear (7), bolts (6), and gear (5).
Illustration 4 g06002564
2/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 5. Remove O-ring seal (8) from gear (7).
Illustration 5 g06172622
6. Use Tooling (A) to remove bushing (7A) from gear assembly (7).
Illustration 6 g06172537
7. Remove bolts (9), adapter assembly (10), and the O-ring seal.
Illustration 7 g06172541
8. Use Tooling (B) to remove bearing (11) from adapter assembly (10).
3/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 8 g06172549
9. Remove gear assembly (12).
Illustration 9 g06172554
10. Remove cover (13) and the O-ring seal.
Illustration 10 g06172557
11. Use Tooling (B) to remove bearing (14).
Installation Procedure
4/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Table 2
Required Tools
Tool Part Number Part Description Qty
A 095-0706 Bolt 2
Illustration 11 g06172557
Illustration 12 g06172580
5/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 13 g06172587
1. Lower the temperature of bearing (14). Be sure to match Dimension (B) and Dimension (C)
when installing bearing (14.). Dimension (B) indicates the angle of the joint on bearing (14).
Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing (14) to the end
of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
Illustration 14 g06172554
2. Install the O-ring seal and cover (9).
6/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g06172597
3. Install gear assembly (12) with oil passage plug (12A) facing out.
Illustration 16 g06172601
Illustration 17 g06172609
4. Lower the temperature of bearing (11). Be sure to match Dimension (F) and Dimension (G)
when installing bearing (11) into adapter assembly (10). Dimension (F) indicates the angle
of the joint on bearing (11). Dimension (F) is 15° ± 1°. Dimension (G) shows the distance
from bearing (11) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
7/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 18 g06172537
5. Install the O-ring seal, adapter assembly (10), and bolts (9).
Illustration 19 g06172619
6. Lower the temperature of bearing (7A). Install bearing (7A) into gear assembly (7). Be sure
that each relief (H) is within 2° of each relief in gear assembly (7).
Illustration 20 g06002564
7. Install O-ring seal (8) onto gear (7).
8/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 21 g06002578
8. Install gear (5) and bolts (6).
Note: Tooling (A) is for supporting gear (7) during the installation of the cover and the rear
crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check
the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
9. Install gear (7) and Tooling (C).
Illustration 22 g06002581
10. Install cover (3), the seal, bolts (4), and the washers.
9/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 23 g06002592
11. Install rear crankshaft seal (1) and bolts (2).
12. Remove Tooling (C).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:26:41 UTC+0800 2020
10/10
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M0...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249234
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
1/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g01132214
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 79 kg (175 lb).
2. Remove top bolt (1). Install Tooling (B).
3. Remove remaining bolts (1).
4. Remove flywheel (2).
5. Use a hammer and a punch in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:27:37 UTC+0800 2020
2/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06123534
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
C - Loctite 242 1
Always wear protective gloves when handling parts that have been
heated.
1. Raise the temperature of the ring gear. Position the ring gear with the part number toward
the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel.
1/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g01132214
2. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 79 kg (175 lb).
3. Position flywheel (2) on Tooling (B) .
4. Apply Tooling (C) to bolts (1) .
5. Install bolts (1) . Remove Tooling (B) . Install remaining bolt (1) . Tighten the bolts evenly
to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:28:33 UTC+0800 2020
2/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010889
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g01132235
1. Remove bolts (1).
2. Remove crankshaft rear seal (2).
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:29:29 UTC+0800 2020
2/2
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010890
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place to dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 7 12:30:24 UTC+0800 2020
3/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249340
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
1. Support the engine.
Illustration 1 g01132273
1/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb).
3. Remove bolts (1) and flywheel housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Apply Tooling (A) to the face of the cylinder block.
Illustration 2 g01132273
2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder
block.
3. Install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Sep 7 12:31:20 UTC+0800 2020
2/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 EXCAVATOR WEC
Configuration: 349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249982
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
1/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
25. Illustration 1 g01132580
1. Remove belt (1).
2. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Remove bolts
(2).
3. Remove crankshaft vibration damper and pulley (3).
Installation Procedure
2/3
349D2 L Excavator WEC00001-UP (MACHINE) POWERED BY C13 Engine(M008...
2020/9/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...