1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, taking safety precautions around springs.
3. Reassembly instructions are also provided in reverse order, with specifications and torque requirements for components. Tools and lubricants required are listed.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f l excavator (prefix wna) service repair manual (wna0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L and 352F excavator. It begins by describing the required tools and safety precautions. The 32-step disassembly procedure removes components like plugs, springs, pistons, and bearings. The assembly section provides specifications, required tools, and a 28-step procedure to reinstall components in reverse order. Precautions are given to lubricate parts and apply locking agents in correct locations.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...cdsaas
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix rgd) service repair manual (rgd0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists 31 steps to fully disassemble the travel motor by removing components like the head, plates, seals, pins, brake piston, disks, and housing keys. Reassembly requires reversing the disassembly steps and ensuring parts are cleaned and placed back in their original locations and orientations. Special tools are listed to aid in removal and installation of components.
Caterpillar cat 349 f lxe excavator (prefix sfg) service repair manual (sfg00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs applying anti-seize compound and Loctite to bearings and bolts before installing 14 parts in the reverse order of disassembly. Precise torques are specified for installing each component.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f l excavator (prefix wna) service repair manual (wna0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L and 352F excavator. It begins by describing the required tools and safety precautions. The 32-step disassembly procedure removes components like plugs, springs, pistons, and bearings. The assembly section provides specifications, required tools, and a 28-step procedure to reinstall components in reverse order. Precautions are given to lubricate parts and apply locking agents in correct locations.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...cdsaas
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix rgd) service repair manual (rgd0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists 31 steps to fully disassemble the travel motor by removing components like the head, plates, seals, pins, brake piston, disks, and housing keys. Reassembly requires reversing the disassembly steps and ensuring parts are cleaned and placed back in their original locations and orientations. Special tools are listed to aid in removal and installation of components.
Caterpillar cat 349 f lxe excavator (prefix sfg) service repair manual (sfg00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs applying anti-seize compound and Loctite to bearings and bolts before installing 14 parts in the reverse order of disassembly. Precise torques are specified for installing each component.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
Kobelco sk300 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. Safety information is provided throughout, including general safety, safety precautions, and warnings.
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualfjsjjekdkme
This document is the shop manual for a hydraulic excavator. It contains outlines, precautions, and general information for repairing and maintaining the excavator. The manual is divided into chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for safety, preparing for disassembly, hydraulic and electrical equipment, and welding repairs. Copyright information is also included.
Kobelco sk260 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety practices, hydraulic system repair, electrical work, and welding. Permission is required to copy or distribute content from the copyrighted manual. Measurements use the international unit system. Technicians should thoroughly read and understand the manual before performing any repair work.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
Kobelco sk60 8 hydraulic excavator service repair manualfjsjjekdkme
This document appears to be a shop manual that contains information for maintenance and repair of hydraulic excavators. It includes sections on specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures. The document provides safety precautions for repairs and disassembly/assembly. It also includes a table for international unit conversion. The manual is intended as a technical reference for maintenance technicians to perform repairs and find fault equipment.
This shop manual provides information needed for the disassembly, reassembly, and repair of a Kawasaki 135ZV-2 wheel loader. It includes specifications, tightening torques, and service standards for the chassis, power, hydraulic, brake, and operator station systems. Safety precautions and symbols are defined. The manual instructs technicians on removing and installing major components like the engine, transmission, axles, cylinders, and more. Cautions are provided regarding parts handling and use of sealants or lock agents.
This shop manual provides information for performing maintenance and repairs on Kawasaki wheel loaders. It contains safety warnings and symbols, an outline of the loader components and maintenance schedule, recommended lubricants, and sections about inspecting and adjusting the chassis and power groups. Technical details are given for linkage pins, center pins, engine and transmission mounts, and the radiator mount. The purpose is to ensure good machine performance through following the correct maintenance and repair procedures.
Kawasaki 92 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 92 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component information for operating heavy machinery. It outlines proper procedures for starting and using the machine, transporting loads, and performing maintenance safely. Operators must follow guidelines to prevent injuries or accidents from improper or unsafe operation. The manual describes the various controls, switches, and components in the operator cab.
Kawasaki 90 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 90 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component descriptions for a machine. It outlines various hazards to avoid when operating or servicing the machine, such as ensuring safety before leaving the operator's seat, wearing protective clothing, and avoiding contact with moving parts. It also describes the machine's components, including the operator's station, consoles, switches, and monitoring systems. Maintenance procedures should follow safety practices like supporting the machine properly and avoiding high-pressure fluids.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and reassembling a wheel loader. It discusses preparing the work area, inspecting components, draining fluids, cleaning parts, applying lubricants, and ensuring proper tightening of fasteners. Special attention should be given to sliding surfaces, seals, and markings for reassembly. Tools and loose parts should be accounted for after completion. Floating seals and nylon slings require special handling to prevent damage or improper installation.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)fjsjjekdkme
This document provides specifications and component layout information for a 90Z6 wheel loader.
The specifications section lists operating weights, engine details, dimensions, speeds and other technical specifications for the GSC and LSC models.
The component layout sections include diagrams and lists showing the layout and weights of major components such as the chassis, powertrain, hydraulic, electrical and other systems. Component names, locations and approximate weights are provided.
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document is a parts catalog for a wheel loader model 90Z6 powered by a Cummins QSM11 engine. It lists parts grouped by system including the front axle, rear axle, power train, engine systems, cab, chassis, electrical systems, hydraulic system, brake system and loader attachments. The document provides part numbers, part names, quantities and the applicable serial number range for each part listed.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)fjsjjekdkme
This document provides specifications and layout diagrams for the components of a wheel loader. It includes:
- Specifications for dimensions, weights, engine details, speeds, and more.
- Overview diagrams showing the layout of main components such as the bucket, cylinders, lights, engine, and more.
- Detailed diagrams labeling locations of the engine, radiator, filters, tanks, valves, pumps, axles, and other parts.
- An overview of the electric system components around the cab, hydraulic oil tank, fuel tank, and engine.
- Sections providing specifications for the engine, hydraulic and electrical components.
The document contains detailed information on the specifications, component layout and electrical
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
Kobelco sk300 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. Safety information is provided throughout, including general safety, safety precautions, and warnings.
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualfjsjjekdkme
This document is the shop manual for a hydraulic excavator. It contains outlines, precautions, and general information for repairing and maintaining the excavator. The manual is divided into chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for safety, preparing for disassembly, hydraulic and electrical equipment, and welding repairs. Copyright information is also included.
Kobelco sk260 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety practices, hydraulic system repair, electrical work, and welding. Permission is required to copy or distribute content from the copyrighted manual. Measurements use the international unit system. Technicians should thoroughly read and understand the manual before performing any repair work.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
Kobelco sk60 8 hydraulic excavator service repair manualfjsjjekdkme
This document appears to be a shop manual that contains information for maintenance and repair of hydraulic excavators. It includes sections on specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures. The document provides safety precautions for repairs and disassembly/assembly. It also includes a table for international unit conversion. The manual is intended as a technical reference for maintenance technicians to perform repairs and find fault equipment.
This shop manual provides information needed for the disassembly, reassembly, and repair of a Kawasaki 135ZV-2 wheel loader. It includes specifications, tightening torques, and service standards for the chassis, power, hydraulic, brake, and operator station systems. Safety precautions and symbols are defined. The manual instructs technicians on removing and installing major components like the engine, transmission, axles, cylinders, and more. Cautions are provided regarding parts handling and use of sealants or lock agents.
This shop manual provides information for performing maintenance and repairs on Kawasaki wheel loaders. It contains safety warnings and symbols, an outline of the loader components and maintenance schedule, recommended lubricants, and sections about inspecting and adjusting the chassis and power groups. Technical details are given for linkage pins, center pins, engine and transmission mounts, and the radiator mount. The purpose is to ensure good machine performance through following the correct maintenance and repair procedures.
Kawasaki 92 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 92 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component information for operating heavy machinery. It outlines proper procedures for starting and using the machine, transporting loads, and performing maintenance safely. Operators must follow guidelines to prevent injuries or accidents from improper or unsafe operation. The manual describes the various controls, switches, and components in the operator cab.
Kawasaki 90 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 90 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component descriptions for a machine. It outlines various hazards to avoid when operating or servicing the machine, such as ensuring safety before leaving the operator's seat, wearing protective clothing, and avoiding contact with moving parts. It also describes the machine's components, including the operator's station, consoles, switches, and monitoring systems. Maintenance procedures should follow safety practices like supporting the machine properly and avoiding high-pressure fluids.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and reassembling a wheel loader. It discusses preparing the work area, inspecting components, draining fluids, cleaning parts, applying lubricants, and ensuring proper tightening of fasteners. Special attention should be given to sliding surfaces, seals, and markings for reassembly. Tools and loose parts should be accounted for after completion. Floating seals and nylon slings require special handling to prevent damage or improper installation.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)fjsjjekdkme
This document provides specifications and component layout information for a 90Z6 wheel loader.
The specifications section lists operating weights, engine details, dimensions, speeds and other technical specifications for the GSC and LSC models.
The component layout sections include diagrams and lists showing the layout and weights of major components such as the chassis, powertrain, hydraulic, electrical and other systems. Component names, locations and approximate weights are provided.
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document is a parts catalog for a wheel loader model 90Z6 powered by a Cummins QSM11 engine. It lists parts grouped by system including the front axle, rear axle, power train, engine systems, cab, chassis, electrical systems, hydraulic system, brake system and loader attachments. The document provides part numbers, part names, quantities and the applicable serial number range for each part listed.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)fjsjjekdkme
This document provides specifications and layout diagrams for the components of a wheel loader. It includes:
- Specifications for dimensions, weights, engine details, speeds, and more.
- Overview diagrams showing the layout of main components such as the bucket, cylinders, lights, engine, and more.
- Detailed diagrams labeling locations of the engine, radiator, filters, tanks, valves, pumps, axles, and other parts.
- An overview of the electric system components around the cab, hydraulic oil tank, fuel tank, and engine.
- Sections providing specifications for the engine, hydraulic and electrical components.
The document contains detailed information on the specifications, component layout and electrical
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349F L EXCAVATOR TEW
Configuration: 349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349F and 352F Excavators Machine Systems
Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07203491
Travel Motor - Disassemble
SMCS - 4351-015
Disassemble Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
154-6182 M12x1.75 mm Forcing Bolt 2
6V-8149 M12x1.75 mm Nut 4
5P-8245 M12 Hard Washer 4
D
- M3x0.5 Threaded Rod 1
3K-3068 3 mm Thrust Washer 1
3C-6969 M3x0.5 Nut 2
E
8T-0276 M8x45mm Bolt 2
9M-1974 M8 Hard Washer 2
Start By:
a. Remove travel motor.
NOTICE
1/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06252257
1. Use Tooling (B) and a suitable lifting device to position travel motor (1) in a vertical
position on Tooling (A). The weight of travel motor (1) is approximately 136 kg (300 lb).
Use Tooling (C) to attach travel motor (1) to Tooling (A).
Illustration 2 g06252275
2. Remove plugs (2), plug (3), plug (4), and the O-ring seals.
2/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 3 g06252280
Illustration 4 g06252989
3. Remove plug (6) and the O-ring seal.
4. Remove plug (5), stopper (7), and ball (8).
3/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g06255756
Illustration 6 g06255791
5. Use Tooling (D) and a suitable washer to extract seat (8A).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g06252992
Illustration 8 g06252996
6. Remove plugs (9) and the O-ring seals.
7. Remove plug (10), spool (11), spring (12), and the O-ring seal.
Illustration 9 g06253028
8. Remove plug (13), valve (14) , and the O-ring seals.
5/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g06253047
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove the top two nuts and washers from Tooling (C).
10. Remove bolts (15).
11. Use Tooling (B) and a suitable lifting device to remove motor head assembly (16). The
weight of motor head assembly (16) is approximately 45 kg (100 lb). Remove motor head
assembly (16).
Illustration 11 g06253060
12. Remove bearing (17) and O-ring seal (18).
6/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g06253330
13. Reinstall the washers and nuts from Tooling (C) that were removed in a previous Step.
14. Remove springs (19), O-ring seal (20), port plate (21), O-ring seal (22), plug (23), and the O
-ring seal.
Note: Port plate (21) may still be adhered to the bottom of motor head assembly (16).
Illustration 13 g06253333
15. Remove orifice (24) and orifice (25).
Illustration 14 g06253335
7/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 16. Remove plug (26).
Illustration 15 g06253475
17. Use Tooling (E) and suitable prying devices to remove piston assembly (27).
Illustration 16 g06253502
Illustration 17 g06253508
Typical example.
18. Remove separator plates (28) and friction plates (29). Note the alternating order of separator
plates (28) and friction plates (29) for assembly purposes.
8/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g06253734
19. Remove barrel assembly (30).
Note: Do not allow the components of barrel assembly (30) to come apart while you
remove barrel assembly (30). The components of barrel assembly (30) must be reinstalled
into the original positions.
Illustration 19 g06253741
20. Remove piston assemblies (31) and retainer (32).
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g06253748
21. Remove guide (33).
Illustration 21 g06253755
22. Remove springs (34).
Illustration 22 g06254252
23. Put location marks on swashplate (35) for assembly purposes. Remove swashplate (35).
10/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g06254282
24. Remove snap ring (37) and roller (36).
Illustration 24 g06254306
25. Remove keys (38).
Illustration 25 g06254363
26. Remove snap ring (40).
27. Use a soft faced hammer to remove shaft assembly (39).
11/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g06254423
28. Remove snap ring (41).
29. Use a suitable press to remove bearing (42) from shaft assembly (39).
Illustration 27 g06254449
30. Remove O-ring seal (43) and O-ring seal (44).
Illustration 28 g06254465
12/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g06254467
31. Remove plug (45) and use compressed air to remove piston (46).
Illustration 30 g06254480
32. Remove lip seal (47).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 26 18:25:50 UTC+0800 2020
13/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349F L EXCAVATOR TEW
Configuration: 349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349F and 352F Excavators Machine Systems
Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i06563923
Travel Motor - Assemble
SMCS - 4351-016
Specifications
Illustration 1 g03845362
NOTICE
To prevent damage to the motor, the case must be filled with clean
hydraulic oil at least to the fill port before operation.
1/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Table 1
Specification for 390-1088 Travel Motor Gp
Item Qty Part Specification Description
1 1 5P-7684 Plug Torque to 430 ± 40 N·m (317 ± 30 lb ft).
2 1
6K-6307 O-
Ring Seal
Lubricate with 1U-6396 O-Ring Assembly Compound.
- - -
Before assembly, lubricate the sliding surfaces of the cam plate
(3), the hold-down (4), the pistons (5), the barrel (6) and the shaft
(8) lightly with clean hydraulic oil.
7 20
124-1561 Brake
Spring
Length under test force is 19.0 mm (0.75 inch).
Test force is 425 ± 43 N (96 ± 10 lb).
Free length after test is 22.06 mm (0.869 inch).
9 1
6V-3382 Lip
Type Seal
Apply blue Loctite 243 to the outside diameter.
10 1
118-5805
Special Race
Bearing
Install the snap ring of the special race bearing toward the shaft
flange.
11 2
9S-4185 O-
Ring Plug
Torque to 82 ± 8 N·m (60 ± 6 lb ft).
12 6 8T-4187 Bolt Torque to 530 ± 70 N·m (391 ± 52 lb ft).
13 2
9S-4183 O-
Ring Plug
Torque to 190 ± 20 N·m (140 ± 15 lb ft).
Illustration 2 g03845364
Section A-A
Table 2
2/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Item Qty Part Specification Description
14 2
1T-0936 Pipe
Plug
Install in the orifice toward the head surface or below the head
surface.
15 1 124-1554 Spring
Length under test force is 15 mm (0.6 inch).
Test force is 15.0 ± 2.0 N (3.4 ± 0.4 lb).
Free length after test is 16.15 mm (0.636 inch).
D - -
Depth from the head and interface of the port plate is
20.0 ± 0.2 mm (0.79 ± 0.01 inch).
16 1
195-4456 Orifice
Plug
Torque to 7 ± 1 N·m (62 ± 9 lb in).
Illustration 3 g03845365
Section C-C
Table 3
Item Qty Part Specification Description
17 1 230-5483 Spring
Length under test force is 25 mm (1.0 inch).
Test force is 60.0 ± 8.0 N (13.5 ± 1.8 lb).
Free length after test is 35 mm (1.4 inch).
18 1 087-4786 Adapter Torque to 115 ± 10 N·m (85 ± 7 lb ft).
Assembly Procedure
Table 4
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
D 3E-3879 Eyebolt 1
3/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. F 1U-6396 O-Ring Assembly Compound 1
G - Loctite 242 -
H 1P-0510 Driver Gp 1
J 6V-2055 Grease 1
K 128-5049 Guide Stud 2
Illustration 4 g02421056
1. Lubricate actuator piston (41) with the oil that is being used. Install actuator piston (41) into
housing (2). Apply Tooling (F) onto O-ring seal of plug (40). Install plug (40) into motor
housing (2).Tighten plug (42) to a torque of 430 ± 40 N·m (315 ± 30 lb ft).
2. Apply Tooling (G) onto outside diameter of seal (43). Use Tooling (H) to install seal (43).
Install retaining ring (42).
Illustration 5 g02421000
4/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 6 g02420998
3. Install pins (39) and keys (38) into motor housing (2).
Illustration 7 g02421876
Illustration 8 g02421958
4. Use a suitable press to install bearing (36) and bearing (37) onto shaft assembly (25). Bearing
(36) must be installed with Retaining Clip (X) toward the barrel assembly.
5/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 13 g02423621
8. Use Tooling (D) and a suitable lifting device to install the rotating group into motor housing
(2). The weight of the rotating group is approximately 30 kg (65 lb).
Note: Align the notches of swashplate (29) with the keys in the motor housing (2).
Note: Protect shaft seal (43) from damage by covering the splines on shaft assembly (25) with
heat shrink tubing.
Illustration 14 g02423738
8/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 15 g02423742
9. Install plates (26) and friction discs (27). Start with plate (26). Alternate between plates (26)
and friction discs (27) with plates (26) on the top and the bottom.
Illustration 16 g02419659
10. Install backup ring (21) and O-ring seal (22) onto brake piston (20).
11. Install backup ring (24) and O-ring seal (23) onto brake piston (20).
Illustration 17 g02419577
12. Install O-ring seals (19) onto motor housing (2). Install springs (18) onto brake piston (20).
9/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 18 g02419439
13. Install balls (17), backup rings (15), O-ring seals (16), and retainers (14) into head assembly
(3).
Illustration 19 g02419416
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install spring (13), spool (12), and adapter (11). Tighten adapter (11) to a torque of
115 ± 10 N·m (85 ± 7 lb ft).
10/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 20 g02419359
15. Install ball (9), spring (8), and orifice (7). Tighten orifice (7) to a torque of 7 ± 1 N·m
(62 ± 9 lb in).
16. Install bearing (6) and O-ring seal (10) onto head assembly (3).
Illustration 21 g02001974
Illustration 22 g02419358
17. Apply Tooling (K) to the back side of plate (5) to hold plate (5) in place during assembly.
Install plate (5) to head assembly (3).
11/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 23 g02424459
Illustration 24 g02419296
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
18. Install Tooling (K) onto motor housing (2). Use Tooling (A) and a suitable lifting device to
install head assembly (3) onto motor housing (2).The weight of the head (3) is approximately
40 kg (90 lb). Remove Tooling (A) and Tooling (D). Install bolts (4). Tighten bolts (4) to a
torque of 530 ± 70 N·m (390 ± 50 lb ft).
12/13
349F & 349F L Excavators TEW00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...