SlideShare a Scribd company logo
Service Repair Manual
Models
345C and 345C L Excavator
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR ESD
Configuration: 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i02407350
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
B 1P-0074 Slide Hammer Puller 1
C 6V-3010 Puller Group 1
D 4C-8359 Eyebolt 1
E 9S-9152 Bearing Puller 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
H 1U-7600 Slide Hammer Puller 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Failure to properly assemble parts or failure to follow established
procedures can lead to damage to the parts and assembly.
To avoid damage to parts, always identify and mark the parts so that
they can be installed into the same location. Never force parts during
assembly. Keep parts clean and lubricated.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
2/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel
motor to a suitable holding fixture in a vertical position. The weight of the travel motor is
141 kg (310 lb).
Illustration 1 g00627438
2. Remove displacement change valve (1) from the head of the travel motor.
Illustration 2 g00624938
3. Remove O-ring seals (2) and rings (3) from the displacement change valve.
Illustration 3 g00628657
3/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plugs (5) from the head. Remove an O-ring seal from each plug.
5. Remove outer bolts (4) from the head of the travel motor.
Illustration 4 g00624949
6. Use Tooling (A) and a suitable lifting device to remove the head of the travel motor from
the travel motor housing. The weight of head (6) is approximately 43 kg (95 lb).
Note: There are pins (7) that may fall out of the inside of the head when the head is
removed.
Note: Be careful during the removal of head (6) from the travel motor housing. Be careful
not to scratch mating surfaces or damage the mating surfaces of the components.
4/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 5 g00624953
7. Turn over the head. If pins (7) are in the bottom side of the head, remove the pins.
Illustration 6 g00627405
8. Remove port plate (8) and O-ring seal (9) from the head.
Illustration 7 g00625967
9. Use Tooling (B) in order to remove bearing (10) from the head of the travel motor.
5/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 8 g00627391
10. Remove plate (11) and remove springs (12) from the travel motor housing.
11. Remove O-ring seals (13) from the upper surface of the travel motor housing.
Illustration 9 g00627377
12. Install Tooling (C) on the brake piston (14). Remove the brake piston.
Illustration 10 g00625888
13. Remove O-ring seals (15) and the backup rings from the brake piston.
Note: Make sure that you take note of the location of the O-rings versus the backup rings.
6/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 11 g00625891
14. Remove separator plates (16) from the travel motor housing.
Illustration 12 g00666743
15. Remove disks (17) from the travel motor housing.
Illustration 13 g00626837
16. Install Tooling (D) to the shaft and use a suitable lifting device in order to remove the
rotating group from the travel motor housing. The weight of the rotating group is 29 kg
(65 lb).
7/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Note: Do not allow the components of the rotating group to come apart during the removal
from the travel motor. All of the components in the rotating group must be reinstalled in the
component's original location.
Illustration 14 g00626633
17. Turn over the rotating group. Remove shaft assembly (18) from the rotating group.
Illustration 15 g00666621
Illustration 16 g00625900
18. Use a suitable press to remove bearing (19) from shaft assembly (18).
8/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 17 g00666622
19. Use Tooling (E) and a suitable press in order to remove inner race (20) from shaft assembly
(18).
Illustration 18 g00625908
20. Remove cam plate (21) from the rotating group.
Illustration 19 g00625911
21. Retainer (22) and piston assemblies (23) are nonserviceable separately. Prior to the removal
of the retainer and the piston assemblies from barrel (24), put identification marks on the
piston assemblies, the retainer and the barrel for assembly purposes.
9/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. The piston assemblies must be reinstalled in the original bores in the retainer and the barrel.
23. Remove retainer (22) and piston assemblies (23) from barrel (24).
24. Separate the piston assemblies from the retainer.
Illustration 20 g00625917
Note: The orientation of the washers (25) is important. The washers must be reinstalled on
barrel (24) in the same orientation.
25. Remove guide (26) and outer spacer (27) from barrel (24).
26. Remove washers (25) and inner spacer (28) from the barrel.
Illustration 21 g00625937
27. Remove keys (29) from the travel motor housing.
10/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 22 g00625920
28. Use Tooling (F) to remove retaining ring (30) from the shaft end of the travel motor
housing.
Illustration 23 g00625936
Illustration 24 g00636454
29. Use Tooling (G) to remove lip seal (31) from the travel motor housing if the shaft has been
removed from the travel motor.
11/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Use Tooling (H) to remove lip seal (31) if the shaft has not been removed from the travel
motor. Place the travel motor in a vertical position when you use Tooling (H) to remove the
lip type seal.
Illustration 25 g00625976
31. Remove plug (33) and piston (32) from the travel motor housing. Remove O-ring seal (34)
from the plug.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 15 14:57:03 UTC+0800 2020
12/12
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR ESD
Configuration: 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i03778971
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
D 4C-8359 Eyebolt 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
J 4C-4030 Thread Lock Compound 1
K 180-6533 Seal Driver 1
L 6V-7030 Micrometer Depth Gauge 1
M 8T-0447 Calipers 1
N 1U-6396 O-Ring Assembly Compound 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
1/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-ring seals , gaskets, and seals should always be replaced. A used O-ring seal may not
have the same sealing properties as a new O-ring seal. Use Tooling (H) during the assembly
procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
Illustration 1 g01204890
1. Install O-ring seal (34) on plug (33).
2. Install piston (32) and the plug in the travel motor body. Tighten the plug to a torque of
430 ± 40 N·m (317 ± 30 lb ft).
2/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g01204916
Illustration 3 g01204919
3. Apply a thin coat of Tooling (J) on the outer surfaces of lip seal (31).
4. Use Tooling (K) and a suitable hammer to drive the lip seal into the travel motor body.
Drive the seal downward until Tooling (K) makes contact with the travel motor housing.
5. Use Tooling (F) to install retaining ring (30) to the shaft end of the travel motor body.
Illustration 4 g01204923
6. Install keys (29) inside the travel motor body.
3/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 5 g01204924
7. Assemble washers (25), inner spacer (28) and outer spacer (27) in the proper orientation, as
shown.
Illustration 6 g01204931
8. Use Tooling (L) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
4/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 7 g00625917
9. Install inner spacer (28), washers (25), and outer spacer (27) to barrel (24).
10. Install guide (26) to the barrel.
Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24).
Illustration 9 g00625908
12. Install cam plate (21) on the rotating group.
5/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 10 g00666621
Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft assembly (18).
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft assembly (18).
Note: Place the two support plates under the lip of shaft assembly (18).
6/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 13 g00626633
15. Insert shaft assembly (18) in the rotating group.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate disks (17) and separator plates (16) into the travel motor housing. Start with a
separator plate and end with a separator plate.
7/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g01204938
18. Use Tooling (M) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 32.2 ± 2 mm (1.27 ± 0.08 inch).
If this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
8/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 18 g00625888
Illustration 19 g00667938
(15) O-Ring seals
19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
9/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g01204953
21. Use Tooling (M) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1.0 mm (0.82 ± 0.04 inch).
If this measurement is off, drive the brake piston further into the travel motor body.
Illustration 22 g00627391
22. Install springs (12) and plate (11).
10/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Install O-ring seals (13).
Illustration 23 g01204965
24. Use Tooling (G) to drive the bearing into the head.
Illustration 24 g00627405
25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g01205007
11/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Turn over head (6). Install Tooling (A) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install Pins (7) into the head.
Illustration 27 g00628657
29. Install an O-ring on each plug (5).
30. Install bolts (4) which hold the head in place. Tighten the six bolts to a torque of
530 ± 70 N·m (391 ± 52 lb ft).
31. Install plugs (5) that hold the pins in the head. Tighten the plugs to a torque of 75 ± 7 N·m
(55 ± 5 lb ft).
12/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 28 g00624938
32. Install O-ring seals (2) and rings (3) on the displacement change valve.
Illustration 29 g00627438
33. Install displacement change valve (1) onto the head of the travel motor. Tighten the
displacement change valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft).
34. To prevent possible damage to the travel motor, the unit should be filled with oil at least up
to the fill port prior to operation. Refer to Operation and Maintenance Manual for the
correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jul 15 14:58:00 UTC+0800 2020
13/13
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng...
2020/7/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

More Related Content

More from fjisejkdmd8id

Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...
fjisejkdmd8id
 
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...
fjisejkdmd8id
 
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
fjisejkdmd8id
 
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...
fjisejkdmd8id
 
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
fjisejkdmd8id
 
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...
fjisejkdmd8id
 
Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...
fjisejkdmd8id
 
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...
fjisejkdmd8id
 
Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...
fjisejkdmd8id
 
Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...
fjisejkdmd8id
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
fjisejkdmd8id
 
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...
fjisejkdmd8id
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
fjisejkdmd8id
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
fjisejkdmd8id
 
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
fjisejkdmd8id
 
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
fjisejkdmd8id
 
Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...
Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...
Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...
fjisejkdmd8id
 
Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...
Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...
Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...
fjisejkdmd8id
 
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...
fjisejkdmd8id
 
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...
fjisejkdmd8id
 

More from fjisejkdmd8id (20)

Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SXB) Service Repair Manual (SXB00...
 
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual (SJL00...
 
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
Caterpillar Cat 430F Backhoe Loader (Prefix RGS) Service Repair Manual (RGS00...
 
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...
Caterpillar Cat 434E BACKHOE LOADER (Prefix FSH) Service Repair Manual (FSH00...
 
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
 
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix HWP) Service Repair Manual (HWP0...
 
Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix JBA) Service Repair Manual (JBA00...
 
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD01...
 
Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...
Caterpillar Cat 432E BACKHOE LOADER (Prefix RXS) Service Repair Manual (RXS00...
 
Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix WEP) Service Repair Manual (WEP00...
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix LYD) Service Repair Manual (LYD0...
 
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...
Caterpillar Cat 432D BACKHOE LOADER (Prefix BLD) Service Repair Manual (BLD00...
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
 
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWG) Service Repair Manual (HWG0...
 
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
Caterpillar Cat 430F Backhoe Loader (Prefix RDF) Service Repair Manual (RDF00...
 
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00...
 
Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...
Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...
Caterpillar Cat 430E BACKHOE LOADER (Prefix SWC) Service Repair Manual (SWC00...
 
Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...
Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...
Caterpillar Cat 428E BACKHOE LOADER (Prefix SNL) Service Repair Manual (SNL00...
 
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual (BXC00...
 
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual (BNS00...
 

Recently uploaded

What Causes Audi Car Battery Failures Solutions and Maintenance Tips
What Causes Audi Car Battery Failures Solutions and Maintenance TipsWhat Causes Audi Car Battery Failures Solutions and Maintenance Tips
What Causes Audi Car Battery Failures Solutions and Maintenance Tips
Woodinville Sports Cars
 
High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...
High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...
High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...
gargjiya84
 
Latest Car Models with Prices and Specs - Visit Ccarprice.com
Latest Car Models with Prices and Specs - Visit Ccarprice.comLatest Car Models with Prices and Specs - Visit Ccarprice.com
Latest Car Models with Prices and Specs - Visit Ccarprice.com
Ccarprice .com
 
HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...
HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...
HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...
gajnagarg
 
High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...
jimmigarg6
 
New Holland Td5010 Td5020 Td5030 Tractors Service Manual
New Holland Td5010 Td5020 Td5030 Tractors Service ManualNew Holland Td5010 Td5020 Td5030 Tractors Service Manual
New Holland Td5010 Td5020 Td5030 Tractors Service Manual
Excavator
 
High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...
gargruksana809
 
Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...
Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...
Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...
ailynolive
 
Volvo L120C Wheel Loader Service Repair Manual
Volvo L120C Wheel Loader Service Repair ManualVolvo L120C Wheel Loader Service Repair Manual
Volvo L120C Wheel Loader Service Repair Manual
Excavator
 
New Holland Tc40 4 Cylinder Tractor Parts Manual
New Holland Tc40 4 Cylinder Tractor Parts ManualNew Holland Tc40 4 Cylinder Tractor Parts Manual
New Holland Tc40 4 Cylinder Tractor Parts Manual
Excavator
 
High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...
komalsharmaa480
 
UiPath Automotive PPT explaining about auto AWS.pptx
UiPath Automotive PPT explaining about auto AWS.pptxUiPath Automotive PPT explaining about auto AWS.pptx
UiPath Automotive PPT explaining about auto AWS.pptx
kalolo8435
 
Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...
Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...
Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...
tanupasswan6
 
Mercedes Maintenance Comprehensive Steps to Prevent and Address Oil Leaks
Mercedes Maintenance Comprehensive Steps to Prevent and Address Oil LeaksMercedes Maintenance Comprehensive Steps to Prevent and Address Oil Leaks
Mercedes Maintenance Comprehensive Steps to Prevent and Address Oil Leaks
Schearer's Sales & Service Inc
 
ALPHARD, VELLFIRE PILOT SEAT CATALOG.pdf
ALPHARD, VELLFIRE PILOT SEAT CATALOG.pdfALPHARD, VELLFIRE PILOT SEAT CATALOG.pdf
ALPHARD, VELLFIRE PILOT SEAT CATALOG.pdf
kenyong0701
 
TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..
TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..
TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..
botbtesting3838
 
Volvo SDLG LG918 Operation Maintenance Manual
Volvo SDLG LG918 Operation Maintenance ManualVolvo SDLG LG918 Operation Maintenance Manual
Volvo SDLG LG918 Operation Maintenance Manual
Excavator
 
Root Cause Analysis....................................
Root Cause Analysis....................................Root Cause Analysis....................................
Root Cause Analysis....................................
AfzalRafeeque1
 
Certified Auto Glass Replacement Professionals
Certified Auto Glass Replacement ProfessionalsCertified Auto Glass Replacement Professionals
Certified Auto Glass Replacement Professionals
O.E. Auto Glass
 
Liquid Penetrant Testing Demystified: Complete Guide
Liquid Penetrant Testing Demystified: Complete GuideLiquid Penetrant Testing Demystified: Complete Guide
Liquid Penetrant Testing Demystified: Complete Guide
SeanMcKernan6
 

Recently uploaded (20)

What Causes Audi Car Battery Failures Solutions and Maintenance Tips
What Causes Audi Car Battery Failures Solutions and Maintenance TipsWhat Causes Audi Car Battery Failures Solutions and Maintenance Tips
What Causes Audi Car Battery Failures Solutions and Maintenance Tips
 
High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...
High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...
High Girls Call Gangtok 000XX00000 Provide Best And Top Girl Service And No1 ...
 
Latest Car Models with Prices and Specs - Visit Ccarprice.com
Latest Car Models with Prices and Specs - Visit Ccarprice.comLatest Car Models with Prices and Specs - Visit Ccarprice.com
Latest Car Models with Prices and Specs - Visit Ccarprice.com
 
HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...
HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...
HiFi Girls Call Coimbatore 000XX00000 Provide Best And Top Girl Service And N...
 
High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Mohali 000XX00000 Provide Best And Top Girl Service And No1 i...
 
New Holland Td5010 Td5020 Td5030 Tractors Service Manual
New Holland Td5010 Td5020 Td5030 Tractors Service ManualNew Holland Td5010 Td5020 Td5030 Tractors Service Manual
New Holland Td5010 Td5020 Td5030 Tractors Service Manual
 
High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Shimla 000XX00000 Provide Best And Top Girl Service And No1 i...
 
Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...
Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...
Busty Girls Call Mumbai 🎈🔥9930687706 🔥💋🎈 Provide Best And Top Girl Service An...
 
Volvo L120C Wheel Loader Service Repair Manual
Volvo L120C Wheel Loader Service Repair ManualVolvo L120C Wheel Loader Service Repair Manual
Volvo L120C Wheel Loader Service Repair Manual
 
New Holland Tc40 4 Cylinder Tractor Parts Manual
New Holland Tc40 4 Cylinder Tractor Parts ManualNew Holland Tc40 4 Cylinder Tractor Parts Manual
New Holland Tc40 4 Cylinder Tractor Parts Manual
 
High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...
High Girls Call Nashik 000XX00000 Provide Best And Top Girl Service And No1 i...
 
UiPath Automotive PPT explaining about auto AWS.pptx
UiPath Automotive PPT explaining about auto AWS.pptxUiPath Automotive PPT explaining about auto AWS.pptx
UiPath Automotive PPT explaining about auto AWS.pptx
 
Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...
Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...
Celebrity Girls Call Delhi 🎈🔥9711199171 🔥💋🎈 Provide Best And Top Girl Service...
 
Mercedes Maintenance Comprehensive Steps to Prevent and Address Oil Leaks
Mercedes Maintenance Comprehensive Steps to Prevent and Address Oil LeaksMercedes Maintenance Comprehensive Steps to Prevent and Address Oil Leaks
Mercedes Maintenance Comprehensive Steps to Prevent and Address Oil Leaks
 
ALPHARD, VELLFIRE PILOT SEAT CATALOG.pdf
ALPHARD, VELLFIRE PILOT SEAT CATALOG.pdfALPHARD, VELLFIRE PILOT SEAT CATALOG.pdf
ALPHARD, VELLFIRE PILOT SEAT CATALOG.pdf
 
TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..
TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..
TOYOTA VOXY 80 SERIES CONSOLE BOX BOTB..
 
Volvo SDLG LG918 Operation Maintenance Manual
Volvo SDLG LG918 Operation Maintenance ManualVolvo SDLG LG918 Operation Maintenance Manual
Volvo SDLG LG918 Operation Maintenance Manual
 
Root Cause Analysis....................................
Root Cause Analysis....................................Root Cause Analysis....................................
Root Cause Analysis....................................
 
Certified Auto Glass Replacement Professionals
Certified Auto Glass Replacement ProfessionalsCertified Auto Glass Replacement Professionals
Certified Auto Glass Replacement Professionals
 
Liquid Penetrant Testing Demystified: Complete Guide
Liquid Penetrant Testing Demystified: Complete GuideLiquid Penetrant Testing Demystified: Complete Guide
Liquid Penetrant Testing Demystified: Complete Guide
 

Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual (ESD00001 and up).pdf

  • 1. Service Repair Manual Models 345C and 345C L Excavator
  • 2. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR ESD Configuration: 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engine Disassembly and Assembly 345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013 i02407350 Travel Motor - Disassemble SMCS - 4351-015 Disassembly Procedure Start By: a. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" . Table 1 Required Tools Tool Part Number Part Description Qty A 3E-3879 Eyebolt 1 B 1P-0074 Slide Hammer Puller 1 C 6V-3010 Puller Group 1 D 4C-8359 Eyebolt 1 E 9S-9152 Bearing Puller 1 F 1P-1862 Pliers 1 G 1P-0510 Driver Group 1 H 1U-7600 Slide Hammer Puller 1 NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair 1/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 3. of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. NOTICE Failure to properly assemble parts or failure to follow established procedures can lead to damage to the parts and assembly. To avoid damage to parts, always identify and mark the parts so that they can be installed into the same location. Never force parts during assembly. Keep parts clean and lubricated. NOTICE Keep all parts clean from contaminants. Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components. To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly. Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination. Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information is available to analyze failures for piston pumps and motors. Refer to Special Publication, SEBD0641, "Analyzing Axial Piston Pump and Motor Failures". Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The installation of used parts during reconditioning is acceptable. Reuse and salvage information is available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations, SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might have caused the original failure. 2/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 4. 1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the travel motor is 141 kg (310 lb). Illustration 1 g00627438 2. Remove displacement change valve (1) from the head of the travel motor. Illustration 2 g00624938 3. Remove O-ring seals (2) and rings (3) from the displacement change valve. Illustration 3 g00628657 3/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 5. Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 4. Remove plugs (5) from the head. Remove an O-ring seal from each plug. 5. Remove outer bolts (4) from the head of the travel motor. Illustration 4 g00624949 6. Use Tooling (A) and a suitable lifting device to remove the head of the travel motor from the travel motor housing. The weight of head (6) is approximately 43 kg (95 lb). Note: There are pins (7) that may fall out of the inside of the head when the head is removed. Note: Be careful during the removal of head (6) from the travel motor housing. Be careful not to scratch mating surfaces or damage the mating surfaces of the components. 4/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 6. Illustration 5 g00624953 7. Turn over the head. If pins (7) are in the bottom side of the head, remove the pins. Illustration 6 g00627405 8. Remove port plate (8) and O-ring seal (9) from the head. Illustration 7 g00625967 9. Use Tooling (B) in order to remove bearing (10) from the head of the travel motor. 5/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 7. Illustration 8 g00627391 10. Remove plate (11) and remove springs (12) from the travel motor housing. 11. Remove O-ring seals (13) from the upper surface of the travel motor housing. Illustration 9 g00627377 12. Install Tooling (C) on the brake piston (14). Remove the brake piston. Illustration 10 g00625888 13. Remove O-ring seals (15) and the backup rings from the brake piston. Note: Make sure that you take note of the location of the O-rings versus the backup rings. 6/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 8. Illustration 11 g00625891 14. Remove separator plates (16) from the travel motor housing. Illustration 12 g00666743 15. Remove disks (17) from the travel motor housing. Illustration 13 g00626837 16. Install Tooling (D) to the shaft and use a suitable lifting device in order to remove the rotating group from the travel motor housing. The weight of the rotating group is 29 kg (65 lb). 7/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 9. Note: Do not allow the components of the rotating group to come apart during the removal from the travel motor. All of the components in the rotating group must be reinstalled in the component's original location. Illustration 14 g00626633 17. Turn over the rotating group. Remove shaft assembly (18) from the rotating group. Illustration 15 g00666621 Illustration 16 g00625900 18. Use a suitable press to remove bearing (19) from shaft assembly (18). 8/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 10. Illustration 17 g00666622 19. Use Tooling (E) and a suitable press in order to remove inner race (20) from shaft assembly (18). Illustration 18 g00625908 20. Remove cam plate (21) from the rotating group. Illustration 19 g00625911 21. Retainer (22) and piston assemblies (23) are nonserviceable separately. Prior to the removal of the retainer and the piston assemblies from barrel (24), put identification marks on the piston assemblies, the retainer and the barrel for assembly purposes. 9/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 11. 22. The piston assemblies must be reinstalled in the original bores in the retainer and the barrel. 23. Remove retainer (22) and piston assemblies (23) from barrel (24). 24. Separate the piston assemblies from the retainer. Illustration 20 g00625917 Note: The orientation of the washers (25) is important. The washers must be reinstalled on barrel (24) in the same orientation. 25. Remove guide (26) and outer spacer (27) from barrel (24). 26. Remove washers (25) and inner spacer (28) from the barrel. Illustration 21 g00625937 27. Remove keys (29) from the travel motor housing. 10/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 12. Illustration 22 g00625920 28. Use Tooling (F) to remove retaining ring (30) from the shaft end of the travel motor housing. Illustration 23 g00625936 Illustration 24 g00636454 29. Use Tooling (G) to remove lip seal (31) from the travel motor housing if the shaft has been removed from the travel motor. 11/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 13. 30. Use Tooling (H) to remove lip seal (31) if the shaft has not been removed from the travel motor. Place the travel motor in a vertical position when you use Tooling (H) to remove the lip type seal. Illustration 25 g00625976 31. Remove plug (33) and piston (32) from the travel motor housing. Remove O-ring seal (34) from the plug. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Jul 15 14:57:03 UTC+0800 2020 12/12 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 14. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR ESD Configuration: 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engine Disassembly and Assembly 345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013 i03778971 Travel Motor - Assemble SMCS - 4351-016 Assembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 3E-3879 Eyebolt 1 D 4C-8359 Eyebolt 1 F 1P-1862 Pliers 1 G 1P-0510 Driver Group 1 J 4C-4030 Thread Lock Compound 1 K 180-6533 Seal Driver 1 L 6V-7030 Micrometer Depth Gauge 1 M 8T-0447 Calipers 1 N 1U-6396 O-Ring Assembly Compound 1 NOTICE Keep all parts clean from contaminants. Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components. 1/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 15. To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly. Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination. Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information is available to analyze failures for piston pumps and motors. Refer to Special Publication, SEBD0641, "Analyzing Axial Piston Pump and Motor Failures". Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The installation of used parts during reconditioning is acceptable. Reuse and salvage information is available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations, SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might have caused the original failure. Note: O-ring seals , gaskets, and seals should always be replaced. A used O-ring seal may not have the same sealing properties as a new O-ring seal. Use Tooling (H) during the assembly procedure. Note: Apply a light film of "10W" oil to all components before assembly. Illustration 1 g01204890 1. Install O-ring seal (34) on plug (33). 2. Install piston (32) and the plug in the travel motor body. Tighten the plug to a torque of 430 ± 40 N·m (317 ± 30 lb ft). 2/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 16. Illustration 2 g01204916 Illustration 3 g01204919 3. Apply a thin coat of Tooling (J) on the outer surfaces of lip seal (31). 4. Use Tooling (K) and a suitable hammer to drive the lip seal into the travel motor body. Drive the seal downward until Tooling (K) makes contact with the travel motor housing. 5. Use Tooling (F) to install retaining ring (30) to the shaft end of the travel motor body. Illustration 4 g01204923 6. Install keys (29) inside the travel motor body. 3/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 17. Illustration 5 g01204924 7. Assemble washers (25), inner spacer (28) and outer spacer (27) in the proper orientation, as shown. Illustration 6 g01204931 8. Use Tooling (L) to measure the distance from the outer spacer to the surface of the table. The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check orientation of the washers. If orientation is correct, replace washers and spacers with new parts. 4/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 18. Illustration 7 g00625917 9. Install inner spacer (28), washers (25), and outer spacer (27) to barrel (24). 10. Install guide (26) to the barrel. Illustration 8 g00625911 11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in barrel (24). Illustration 9 g00625908 12. Install cam plate (21) on the rotating group. 5/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 19. Illustration 10 g00666621 Illustration 11 g00628062 13. Use a suitable press to install bearing (19) onto shaft assembly (18). Illustration 12 g00668076 14. Use a suitable press in order to install inner race (20) onto shaft assembly (18). Note: Place the two support plates under the lip of shaft assembly (18). 6/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 20. Illustration 13 g00626633 15. Insert shaft assembly (18) in the rotating group. Illustration 14 g00625891 Illustration 15 g00666743 16. Alternate disks (17) and separator plates (16) into the travel motor housing. Start with a separator plate and end with a separator plate. 7/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 21. Illustration 16 g00626837 17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel assembly into the travel motor body. Note: Align the notches of the cam plate with the keys in the travel motor body before you lower the barrel assembly into the travel motor body. Illustration 17 g01204938 18. Use Tooling (M) to measure the depth from the top surface of the travel motor body to the bronze face of the barrel assembly. The distance should be 32.2 ± 2 mm (1.27 ± 0.08 inch). If this measurement is off, check orientation of the barrel assembly. Also check if the cam plate is properly seated on the keys. 8/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 22. Illustration 18 g00625888 Illustration 19 g00667938 (15) O-Ring seals 19. Install O-ring seals (15) and the backup rings on the brake piston. Note: Make sure that you install the backup ring and the O-ring seal in the original position. Refer to Illustration 19. 9/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engin... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 23. Illustration 20 g00629015 20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use a soft faced hammer to seat the brake piston correctly. Illustration 21 g01204953 21. Use Tooling (M) to measure the distance from the top of the brake piston (14) to the top surface of the travel motor body. The distance should be 20.8 ± 1.0 mm (0.82 ± 0.04 inch). If this measurement is off, drive the brake piston further into the travel motor body. Illustration 22 g00627391 22. Install springs (12) and plate (11). 10/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 24. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 25. 23. Install O-ring seals (13). Illustration 23 g01204965 24. Use Tooling (G) to drive the bearing into the head. Illustration 24 g00627405 25. Install O-ring seal (9) onto the head. 26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to the port plate in order to hold the port plate in place during the installation of the head. Illustration 25 g01205007 11/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 26. 27. Turn over head (6). Install Tooling (A) onto the head. Use a suitable lifting device to install the head onto the travel motor. Illustration 26 g00631594 28. Install Pins (7) into the head. Illustration 27 g00628657 29. Install an O-ring on each plug (5). 30. Install bolts (4) which hold the head in place. Tighten the six bolts to a torque of 530 ± 70 N·m (391 ± 52 lb ft). 31. Install plugs (5) that hold the pins in the head. Tighten the plugs to a torque of 75 ± 7 N·m (55 ± 5 lb ft). 12/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 27. Illustration 28 g00624938 32. Install O-ring seals (2) and rings (3) on the displacement change valve. Illustration 29 g00627438 33. Install displacement change valve (1) onto the head of the travel motor. Tighten the displacement change valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft). 34. To prevent possible damage to the travel motor, the unit should be filled with oil at least up to the fill port prior to operation. Refer to Operation and Maintenance Manual for the correct oil specification. End By: a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Wed Jul 15 14:58:00 UTC+0800 2020 13/13 345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Eng... 2020/7/15 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...