This document provides disassembly and assembly instructions for the final drive of a 345C L excavator. The final drive disassembly procedure involves 30 steps to remove components like the cover, ring gear, carrier assemblies, planetary gears, and seals. The assembly procedure is not included in full but references using the required tools listed and applying thread lock compound and sealant to reinstall components in the reverse order of disassembly.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 328 d lcr excavator (prefix rmx) service repair manual (rmx00...fjsekdmmeed
This document provides instructions for disassembling and assembling the swing drive of a 328D LCR excavator. It describes in detail how to disassemble the various components of the swing drive including removing the carrier assembly, planetary gears, ring gear, and pinion shaft. It then describes the assembly process for these components in reverse order, providing illustrations and notes on cleaning, lubricating, and installing components like bearings, seals, and retaining rings. The overall process involves using various tools to carefully remove and reinstall over 15 main components of the swing drive.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 318 c excavator (prefix dah) service repair manual (dah00001 ...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 31 steps for disassembly, including draining fluids, separating housing components, and removing internal gears, shafts, seals, and bearings. The 27 steps for assembly describe installing these same parts in reverse order, with notes on cleaning, replacing seals and O-rings, and proper bearing installation techniques.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 328 d lcr excavator (prefix rmx) service repair manual (rmx00...fjsekdmmeed
This document provides instructions for disassembling and assembling the swing drive of a 328D LCR excavator. It describes in detail how to disassemble the various components of the swing drive including removing the carrier assembly, planetary gears, ring gear, and pinion shaft. It then describes the assembly process for these components in reverse order, providing illustrations and notes on cleaning, lubricating, and installing components like bearings, seals, and retaining rings. The overall process involves using various tools to carefully remove and reinstall over 15 main components of the swing drive.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 318 c excavator (prefix dah) service repair manual (dah00001 ...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 31 steps for disassembly, including draining fluids, separating housing components, and removing internal gears, shafts, seals, and bearings. The 27 steps for assembly describe installing these same parts in reverse order, with notes on cleaning, replacing seals and O-rings, and proper bearing installation techniques.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...hhfjksekmm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes in detail how to disassemble the various components of the final drive, including removing the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes the assembly process and how to properly adjust the bearing preload using shims. The goal is to thoroughly clean all parts and check seals before reassembling the final drive with the proper bearing adjustment.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 16 m motor grader (prefix b9h) service repair manual (b9h0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 16M motor grader in 50 steps. It lists all required tools and disassembles components such as sprockets, bearings, seals, gears, housings, and shafts. Safety notices are included to properly handle parts and avoid injury. Detailed illustrations accompany each step to ensure correct disassembly.
Caterpillar cat 311 f lrr excavator (prefix kcw) service repair manual (kcw00...fjskekdmjekm
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 311F LRR excavator. It lists over 30 detailed steps to disassemble components like the sprockets, traction control valve, piston assemblies, barrel assembly, planetary gear assemblies, and more. Safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs during disassembly. Required tools are listed at the beginning, along with references to other documents for fluid capacities and tool part numbers.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists over 30 detailed steps for removing components like the ring gear, carrier assemblies, gears, shafts and seals. Bearing preload is determined by applying specific pressures and measuring clearances with a micrometer. All components must be thoroughly cleaned before precise reassembly in their original locations using torque wrenches and lifting devices, with seals and threaded surfaces coated in locking compound or adhesive.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 324 d fm excavator (prefix jkr) service repair manual (jkr000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 324D FM excavator. It begins with a list of required tools. The disassembly procedure describes removing over 20 components of the final drive in detailed steps. It then describes using a special bench and tools to disassemble additional parts. The assembly section provides the reverse steps to reassemble the final drive components back into the main housing and motor housing.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w006...fjsekdmmeed
1) The document provides step-by-step instructions for disassembling and assembling the governor component of a 3304 engine. It includes 34 steps for disassembly and 33 steps for assembly.
2) Required tools include a driver group, spring clamp, and retaining ring pliers. Cleanliness is emphasized to prevent contaminants from causing wear.
3) Key parts that are disassembled and assembled include the governor shaft, carrier, flyweights, dashpot assembly, valve, piston, and governor servo. Detailed illustrations accompany each step.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v016...fjsekdmmeed
1) The document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304 engine.
2) It describes removing components like the fuel rack, lifters, camshaft and bearings during disassembly.
3) Reassembly instructions include installing bearings, camshaft, lifters, fuel rack, gasket and cover, and ensuring proper end play and alignment of parts.
Caterpillar cat 352 f xe vg excavator (prefix sd2) service repair manual (sd2...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor on a 352F XE VG Excavator. The disassembly procedure involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly procedure describes 18 steps and includes specifications for installing components and torquing fasteners correctly. Tools required are listed for both the disassembly and assembly processes.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 345 c l hydraulic excavator (prefix fpc) service repair manua...9fiseookddk
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust shims to set the proper bearing preload when reassembling the components. Precise positioning of identification marks and alignment of parts is important for correct reassembly.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...ifkkdkmdmd
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts installed back in the original locations and orientations.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...hhfjksekmm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes in detail how to disassemble the various components of the final drive, including removing the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes the assembly process and how to properly adjust the bearing preload using shims. The goal is to thoroughly clean all parts and check seals before reassembling the final drive with the proper bearing adjustment.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 16 m motor grader (prefix b9h) service repair manual (b9h0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 16M motor grader in 50 steps. It lists all required tools and disassembles components such as sprockets, bearings, seals, gears, housings, and shafts. Safety notices are included to properly handle parts and avoid injury. Detailed illustrations accompany each step to ensure correct disassembly.
Caterpillar cat 311 f lrr excavator (prefix kcw) service repair manual (kcw00...fjskekdmjekm
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 311F LRR excavator. It lists over 30 detailed steps to disassemble components like the sprockets, traction control valve, piston assemblies, barrel assembly, planetary gear assemblies, and more. Safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs during disassembly. Required tools are listed at the beginning, along with references to other documents for fluid capacities and tool part numbers.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists over 30 detailed steps for removing components like the ring gear, carrier assemblies, gears, shafts and seals. Bearing preload is determined by applying specific pressures and measuring clearances with a micrometer. All components must be thoroughly cleaned before precise reassembly in their original locations using torque wrenches and lifting devices, with seals and threaded surfaces coated in locking compound or adhesive.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 324 d fm excavator (prefix jkr) service repair manual (jkr000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 324D FM excavator. It begins with a list of required tools. The disassembly procedure describes removing over 20 components of the final drive in detailed steps. It then describes using a special bench and tools to disassemble additional parts. The assembly section provides the reverse steps to reassemble the final drive components back into the main housing and motor housing.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w006...fjsekdmmeed
1) The document provides step-by-step instructions for disassembling and assembling the governor component of a 3304 engine. It includes 34 steps for disassembly and 33 steps for assembly.
2) Required tools include a driver group, spring clamp, and retaining ring pliers. Cleanliness is emphasized to prevent contaminants from causing wear.
3) Key parts that are disassembled and assembled include the governor shaft, carrier, flyweights, dashpot assembly, valve, piston, and governor servo. Detailed illustrations accompany each step.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v016...fjsekdmmeed
1) The document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304 engine.
2) It describes removing components like the fuel rack, lifters, camshaft and bearings during disassembly.
3) Reassembly instructions include installing bearings, camshaft, lifters, fuel rack, gasket and cover, and ensuring proper end play and alignment of parts.
Caterpillar cat 352 f xe vg excavator (prefix sd2) service repair manual (sd2...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor on a 352F XE VG Excavator. The disassembly procedure involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly procedure describes 18 steps and includes specifications for installing components and torquing fasteners correctly. Tools required are listed for both the disassembly and assembly processes.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 345 c l hydraulic excavator (prefix fpc) service repair manua...9fiseookddk
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust shims to set the proper bearing preload when reassembling the components. Precise positioning of identification marks and alignment of parts is important for correct reassembly.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...ifkkdkmdmd
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts installed back in the original locations and orientations.
Caterpillar cat 345 c hydraulic excavator (prefix els) service repair manual ...fjkkekmdm
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts reinstalled in the original locations and orientations.
Caterpillar cat 345 c hydraulic excavator (prefix els) service repair manual ...hfhjskedme
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts reinstalled in the original locations and orientations.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...jjfksekdmejik
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing 30 individual parts in 28 steps, including the final drive cover, carrier assemblies, ring gear, and other internal components. Reassembly follows the reverse order, with notes to reinstall parts in their original locations and orientations. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, a duo-cone seal installer, anti-seize compound, and thread lock compound.
Caterpillar cat 345 c l hydraulic excavator (prefix fpc) service repair manua...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C L Hydraulic Excavator. The disassembly procedure involves removing 28 parts in sequential order, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure similarly involves installing these 28 parts in reverse order, and adjusting the bearing preload by determining the correct number and thickness of shims to install based on precise measurement of gaps using tools like a micrometer. Proper cleaning, application of lubricants, and torque specifications are required.
Caterpillar cat 345 c l hydraulic excavator (prefix fpc) service repair manua...fjskefksemer
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust shims to set the proper bearing preload when reassembling the components. Precise positioning of identification marks and alignment of parts is important for correct reassembly.
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...kmf9ioseodk
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 30 parts from the final drive assembly using various tools. The assembly procedure is the reverse of the disassembly process and includes applying thread lock compound and gasket sealant to specific joints.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...kmf9ioseodk
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves 30 steps to remove all individual components of the drive. This includes removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure will reverse the disassembly process, noting any identification marks and using the required tools and compounds.
Similar to Caterpillar cat 345 c l hydraulic excavator (prefix lys) service repair manual (lys00001 and up) (9)
Caterpillar cat 320 d rr excavator (prefix fxk) service repair manual (fxk000...9fiseookddk
The document provides instructions for removing and installing the crankshaft on Caterpillar 3064 and 3066 engines. It describes removing components like the front housing, oil pan, flywheel housing and connecting rod caps. It then explains how to remove the crankshaft main bearings and thrust washers. For installation, it details lubricating the crankshaft and bearings before lowering the crankshaft into place and securing the main bearing caps with bolts torqued to the specified value. End play is then checked using a dial indicator to ensure it is within the acceptable range.
Caterpillar cat 320 d rr excavator (prefix eby) service repair manual (eby000...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar cat 320 d lrr excavator (prefix hjc) service repair manual (hjc00...9fiseookddk
The document provides instructions for removing and installing valve guides and valve seat inserts from the cylinder head of a Caterpillar 320D LRR excavator engine. It describes:
1) Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2) Using various tools to remove the old valve guides and seat inserts and clean the cylinder head.
3) Lubricating and installing new valve guides so they protrude a specified amount from the cylinder head.
4) Lowering the temperature of new seat inserts and installing them using the appropriate tools.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...9fiseookddk
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar cat 320 d lrr excavator (prefix gkl) service repair manual (gkl00...9fiseookddk
The document provides instructions for checking bearing clearances on excavator engines. It describes the required plastic gauge tools and notes that Cat does not recommend checking actual clearances due to the risk of damage or inaccurate results. It provides instructions for using the plastic gauges to check clearances between main and connecting rod bearings and respective journals if a technician chooses to perform the checks. Safety precautions are outlined such as ensuring clean, dry surfaces and avoiding the use of materials that could damage bearing surfaces.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...9fiseookddk
The document provides instructions for removing and installing the crankshaft on Caterpillar 3064 and 3066 engines. It describes removing components like the front housing, oil pan, flywheel housing and connecting rod caps. It then explains how to remove the crankshaft main bearings and thrust washers. For installation, it details lubricating the crankshaft and bearings and installing the main bearing caps, thrust washers and connecting rod caps, checking end play with a dial indicator.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...9fiseookddk
The document provides instructions for removing and installing various engine components on Caterpillar 320D excavators, including:
1. Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
2. Removing and installing the crankshaft pulley, which requires removing a nut and installing a new oil seal.
3. Removing the crankshaft front seal using a slide hammer puller and being careful not to damage the crankshaft flange.
Caterpillar cat 319 d ln excavator (prefix zca) service repair manual (zca000...9fiseookddk
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 38 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is critical throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d ln excavator (prefix wbj) service repair manual (wbj000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d ln excavator (prefix rjp) service repair manual (rjp000...9fiseookddk
The document provides instructions for disassembling and assembling the final drive of a 319D L and 319D LN excavator. Some key steps include:
- Removing the final drive cover, carrier assembly, ring gears, and other components.
- Disassembling the carrier assembly by removing planetary shafts, gears, bearings, and other internal parts.
- Separating the main housing from the motor housing after removing bolts and gears.
- Cleaning all parts thoroughly before assembly and replacing all O-rings, gaskets, and seals.
- Assembling involves installing bearings, gears, carrier assembly, ring gears, cover, and other components in reverse order of dis
Caterpillar cat 319 d ln excavator (prefix kfm) service repair manual (kfm000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 31 parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs to install 33 parts in reverse order and provides notes on cleaning, lubricating, and setting bearing preload using shims.
Caterpillar cat 319 d ln excavator (prefix fmh) service repair manual (fmh000...9fiseookddk
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with removing the travel motor and cleaning it. Then it describes dismantling the various components like the head, barrel assembly, piston guide, and brake piston. Precise steps are given to disassemble seals, plates, and other parts. The assembly section reverses the process and provides details on installing components in the correct order and orientation while applying lubricants. Proper tool use and safety precautions are emphasized throughout.
Caterpillar cat 319 d ln excavator (prefix eaw) service repair manual (eaw000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. It describes in detail how to disassemble the final drive components including removing the cover, carrier assembly, planetary gears, ring gears, and other parts. It then describes the assembly process and lists the required tools, noting that cleanliness and replacing all seals and gaskets is important.
Caterpillar cat 319 d ln excavator (prefix ayf) service repair manual (ayf000...9fiseookddk
This document provides instructions for disassembling and assembling the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing over 30 individual parts from the final drive assembly using various tools. The assembly procedure instructs to clean all parts thoroughly and replace all O-rings, gaskets and seals before reassembling the final drive in the reverse order of disassembly while applying lubricants to components as needed. Proper cleaning, part replacement, and lubrication are emphasized to ensure correct reassembly.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...9fiseookddk
This document provides assembly instructions for a final drive on an excavator model 319D L. The steps include:
1. Installing the final drive sprocket and bearings
2. Assembling the two carrier assemblies by installing planetary gears, shafts, and pins
3. Installing the assembled carriers, sun gears, and spacer rings
4. Attaching the ring gears and installing the main housing cover
5. Torquing plugs on the cover and completing the final drive assembly
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...9fiseookddk
The document provides disassembly and assembly instructions for the final drive of a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive assembly using various tools. The assembly procedure instructs to install parts in reverse order and provides notes on cleaning, lubrication, and use of replacement seals, gaskets and O-rings. Proper shimming of bearings during assembly is also described.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...9fiseookddk
The document provides instructions for disassembling and assembling the final drive of a 319D L and 319D LN excavator. Some key steps include:
- Removing the final drive cover, carrier assembly, ring gears, and other components.
- Disassembling the carrier assembly by removing planetary shafts, gears, bearings, and other internal parts.
- Separating the main housing from the motor housing after removing bolts and gears.
- Cleaning all parts thoroughly before assembly and replacing all O-rings, gaskets, and seals.
- Assembling involves installing bearings, gears, carrier assembly, ring gears, cover, and other components in reverse order of dis
Caterpillar cat 319 d l excavator (prefix krm) service repair manual (krm0000...9fiseookddk
This document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It describes 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It also describes 31 steps for reassembling these components, including pressing in bearings, determining shim thickness, and installing seals using a special tool. Proper cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...9fiseookddk
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...9fiseookddk
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with removing the travel motor and cleaning it. Then it describes dismantling the various components like the head, barrel assembly, piston guide, and brake piston. Precise steps are given to disassemble seals, plates, and other parts. The assembly section reverses the process and provides details on installing components in the correct order and orientation while applying lubricants. Proper tool use and safety precautions are emphasized throughout.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C L EXCAVATOR LYS
Configuration: 345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i05331566
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive and Travel Motor
- Remove" in this manual.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
1/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01207795
2. Remove coupling (1) from final drive (2) .
3. Attach a suitable lifting device to the final drive, and turn final drive (2) over 180 degrees.
The weight of final drive (2) is approximately 590 kg (1300 lb).
Illustration 2 g01207796
4. Attach the final drive to Tooling (A) . Put an alignment mark across the sections of the final
drive for assembly purposes. All parts must be reinstalled in the original locations.
5. Remove socket head screws (3) from the final drive cover.
2/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g01207801
6. Attach Tooling (B) and a suitable lifting device to cover (5) , as shown. The weight of cover
(5) is approximately 52 kg (115 lb).
7. Remove bolts (4) and the washers that hold the cover in place.
8. Use a soft faced hammer in order to break the seal between cover (5) and the ring gear.
Remove cover (5) . The weight of cover (5) is 52 kg (115 lb).
Illustration 4 g01207835
9. Remove spacer (6) from the cover.
3/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 5 g01207845
10. Remove shims (7) from the cover.
11. Remove socket head bolts (8) and ring gear (9) from the cover.
Illustration 6 g01207864
12. Remove sun gear (10) from carrier assembly (11) . Remove carrier assembly (11) by lifting
the carrier assembly straight up.
13. Disassemble carrier assembly (11) , as follows:
4/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 7 g01207865
a. Remove spacers (12) . A spacer is located on each side of the sun gear in carrier
assembly (11) .
Note: Planetary gears (15) might be stamped with identification marks "L". Note the
position of the identification marks in relation to the carrier for assembly purposes.
Illustration 8 g01207897
b. Remove retaining ring (13) with Tooling (C) .
c. Remove thrust washers (14) and planetary gear (15) from the carrier.
d. Remove bearing (16) from the planetary gear.
e. Repeat Steps 13.b through 13.d for the other two planetary gears.
Illustration 9 g01208035
f. Use a screwdriver in order to remove retaining ring (17) from the carrier. Remove sun
gear (18) from the carrier.
5/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g01208136
14. Attach Tooling (D) and a suitable lifting device to carrier assembly (19) , as shown.
Remove carrier assembly (19) by pulling the carrier assembly straight up. The weight of
carrier assembly (19) is approximately 45 kg (100 lb).
15. Disassemble carrier assembly (19) , as follows:
Note: Spacer (20) may remain with carrier assembly (19) , or the spacer may remain with
carrier assembly (28) . Refer to Step 17.
Illustration 11 g01208162
a. Remove spacer (20) from carrier assembly (19) .
6/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 12 g01208169
b. Drive spring pin (21) into planetary shaft (22) with a hammer and a punch.
Illustration 13 g01208189
c. Remove planetary shaft (22) , two thrust washers (23) and planetary gear (24) from
the carrier.
Note: Planetary gears (24) might be stamped with identification marks "M". Note the
position of the identification marks in relation to the carrier for assembly purposes.
d. Remove bearing (25) from the planetary gear.
e. Remove spring pin (21) from planetary shaft (22) with a hammer and a punch.
f. Repeat Steps 15.b through 15.e in order to remove the other two planetary gears from
the carrier.
7/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 14 g01208245
g. Use a screwdriver to remove retaining ring (26) . Remove sun gear (27) from the
carrier.
Illustration 15 g01208253
16. If spacer (20) was not removed in Step 15.a, remove the spacer from carrier assembly (28)
at this time.
Illustration 16 g01208256
8/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 17. Attach Tooling (E) and a suitable lifting device to carrier assembly (28) , as shown. Remove
carrier assembly (28) . The weight of carrier assembly (28) is approximately 64 kg (140 lb).
18. Disassemble carrier assembly (28) , as follows:
Illustration 17 g01208265
a. Drive spring pin (29) into planetary shaft (30) with a hammer and a punch.
Illustration 18 g01208280
b. Remove planetary shaft (30) , two thrust washers (31) , and planetary gear (32) from
the carrier.
Note: Planetary gears (32) might be stamped with identification marks "N". Note the
position of the identification marks in relation to the carrier for assembly purposes.
c. Remove bearings (33) from the planetary gear.
d. Drive spring pin (29) out of planetary shaft (30) with a hammer and a punch.
e. Repeat Steps 18.a through 18.d in order to remove the other three planetary gears
from the carrier.
9/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 19 g01208300
19. Fasten Tooling (E) and a suitable lifting device to ring gear (34) , as shown. Remove ring
gear (34) from sprocket housing (35) . The weight of ring gear (34) is approximately 82 kg
(180 lb).
Illustration 20 g01208542
20. Remove O-ring seal (36) from sprocket housing (35) .
10/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Eng...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 21 g01208553
Note: Mark the orientation of coupling (38) for assembly purposes.
21. Remove bolts (37) from coupling gear (38) .
Illustration 22 g01208572
22. Install suitable forcing bolts (39) in coupling gear (38) , as shown. Tighten the forcing bolts
evenly in order to loosen coupling gear (38) . Remove the coupling gear from the motor
housing.
Illustration 23 g01208578
11/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Eng...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 24 g01208625
23. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
24. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Separate the sprocket housing from the motor housing. The weight of sprocket housing (35)
is 127 kg (280 lb).
Illustration 25 g01208626
25. Remove the locating pins from the motor housing.
26. Remove duo-cone seal gp (41) from the motor housing.
27. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
12/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Eng...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 26 g01208633
28. Remove duo-cone seal gp (43) from the sprocket housing.
29. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
30. Remove the bearing cups from the sprocket housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 5 15:00:33 UTC+0800 2020
13/13
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Eng...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C L EXCAVATOR LYS
Configuration: 345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i05970668
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 8T-0531 Duo-Cone Seal Installer As 1
H 4C-5599 Anti-Seize Compound 1
J 9S-3263 Thread Lock Compound 1
K 1U-8846 Gasket Sealant 1
L 6V-7059 Micrometer 1
M 1U-9895 Crossblock 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly. Check the condition of all O-ring seals that are used in the final drive. If
1/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. any of the seals are damaged, use new parts for replacement. Reassemble the final drive on
Tooling (A) .
Illustration 1 g01208879
2. Apply Tooling (H) to the surfaces inside sprocket housing (35) that makes contact with the
bearing cups. Install a bearing cup that is in each side of the sprocket housing with a press.
Make sure that the bearing cups are properly seated.
3. Apply Tooling (H) to the surfaces inside the motor housing that makes contact with bearing
cones (42) .
4. Install inner bearing cone (42) on the motor housing.
Illustration 2 g01208625
5. Apply Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown. The
weight of sprocket housing (35) is approximately 127 kg (280 lb). Install sprocket housing
(35) on the motor housing. Carefully install outer bearing cone (42) on the sprocket housing.
2/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 3 g01208578
6. Adjust the bearing preload of the final drive. Determine the correct number of shims (40)
that are required for the proper bearing preload, as follows:
Illustration 4 g01208987
a. Use a depth micrometer in order to measure the step height of coupling gear (38) at
several locations around the gear. Find the average for the measured dimensions
around the gear and record the dimension. Call this Dimension (X) .
b. Apply a load of 10000 kg (22000 lb)to bearing cones (42) .
c. Rotate sprocket housing (35) several times in order to seat the bearing cones.
d. Reduce the load to 3500 ± 350 kg (7700 ± 770 lb).
3/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 5 g00631001
Illustration 6 g03742848
e. While the load is still on the bearing cones, measure the distance between the top face
of the motor housing and the top face of bearing cone (42) . Take measurements in
several locations around the motor housing. Find the average of the measured
dimensions, and record the dimensions. Call this Dimension (Y) .
f. Determine the correct thickness of shims (40) which are used between bearing cone
(42) and coupling gear (38) . Use the following equation in order to determine the
shim pack thickness.
Shim pack thickness ... (X) − (Y) ± 0.05 mm (0.002 inch)
Note: If shims (40) are required, install the thinnest shim next to coupling gear (38)
during final assembly.
4/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 7 g01208625
7. Apply Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Separate sprocket housing (35) from the motor housing.
ReferenceRefer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that makes contact with the seals must be clean and
dry. After installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal
seals.
Illustration 8 g00631006
5/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 9 g01208999
8. Install Duo-Cone seal kit (43) in the sprocket housing with Tooling (G) .
Illustration 10 g00631014
Illustration 11 g01208626
Illustration 12 g01208625
6/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 9. Install Duo-Cone seal kit (41) in the motor housing with Tooling (G) .
10. ApplyTooling (H) in the bores for the locating pins that are in the motor housing. Reinstall
the locating pins in the motor housing.
11. Make sure that inner bearing cone (42) is seated properly on the motor housing.
Note: Do not scratch Duo-Cone seal gp (41) or damage the Duo-Cone seal gp in the main
housing, or the motor housing during assembly of the two components. After installation of
the main housing on the motor housing, there will be a small gap between the components.
The gap between the components is caused by the Duo-Cone seal kit. This will be
eliminated during the installation of the coupling gear.
12. Attach Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Carefully install the sprocket housing on the motor housing.
13. Install outer bearing cone (42) on the sprocket housing. Make sure that the outer bearing
cone is properly seated.
Illustration 13 g01208578
14. Install shims (40) that were determined in Steps 6.a through 6.f on the end of the sprocket
housing, as shown. If shims were required, make sure that the thinnest shim is installed on
top.
7/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 14 g01208553
15. Put coupling gear (38) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (37) that hold coupling gear (38) in position.
Tighten bolts (37) evenly and tighten the bolts in diagonally opposite pairs.
Illustration 15 g01208542
17. Install O-ring seal (36) in sprocket housing (35) .
Illustration 16 g01208300
18. Thoroughly clean the mating surface of sprocket housing (35) that will make contact with
ring gear (34) .
19. Apply a bead of Tooling (K) on the mating surface of ring gear (34) .
20. Attach Tooling (E) and a suitable lifting device to ring gear (34) . Put ring gear (34) in
position on the sprocket housing. The weight of ring gear (34) is approximately 82 kg (180
lb). Make sure that the alignment mark up on the sprocket housing and the ring gear line
with each other.
8/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 17 g01208280
Illustration 18 g01208265
9/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Engin...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 19 g00513451
21. Assemble carrier assembly (28) , as follows:
Note: If planetary gear (32) is stamped with an "N", make sure that the planetary gear
identification grooves are facing in the correct direction, which was noted during the
disassembly of the carrier assembly (28) .
a. Assemble carrier assembly (28) .
b. Put clean SAE 30 oil on bearings (33) .
c. Install bearings (33) in planetary gear (32) .
d. Install a thrust washer (31) on each side of the planetary gear.
e. Install the planetary gear and thrust washers in carrier (28) .
f. Install planetary shaft (30) in carrier (28) and through planetary gear (32) . Make sure
that the spring pin hole in the planetary shaft is in alignment with the spring pin hole
in the carrier.
g. Install spring pin (29) in the carrier and into the planetary shaft. Install the spring pin
until the spring pin is even with the outside surface of the carrier. Orient the split in
the spring pin horizontally to the carrier. Align the split in the spring pin to the left or
to the right. Refer to Illustration 19.
h. Make a stake mark on each side of the spring pin hole in the carrier. This will prevent
the spring pin from falling out of the spring pin hole. Each stake mark should be
approximately 1.5 to 3.00 mm (.59 to .118 inch) from the spring pin hole.
i. Repeat Steps 21.a through 21.h in order to install the remaining three planetary gears
in carrier (30) .
Illustration 20 g01208256
22. Attach Tooling (E) and a suitable lifting device to carrier assembly (28) . The weight of
carrier assembly (28) is approximately 64 kg (140 lb). Put carrier assembly (28) in position
10/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Eng...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. in the ring gear. It will be necessary to rotate carrier assembly (28) back and forth during
installation in order to engage all the gears properly.
Illustration 21 g01208253
23. Install spacer (20) on carrier assembly (28) .
24. Assemble carrier assembly (19) , as follows:
Illustration 22 g01208245
11/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Eng...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 23 g01208189
Illustration 24 g01208169
12/20
345C L Hydraulic Excavator LYS00001-UP (MACHINE) POWERED BY C13 Eng...
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...