The document provides instructions for removing and installing a travel motor on an excavator. It describes draining the final drive oil first. Then it details disconnecting hydraulic lines and removing bolts to detach the final drive and travel motor assembly. The travel motor is then separated from the final drive housing by removing additional bolts. Reinstallation follows the removal steps in reverse order, ensuring proper orientation and applying threadlocker to bolts.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic lines before removal.
2) Using lifting equipment to remove the final drive and travel motor assembly, travel motor, and coupling.
3) Cleaning and lubricating parts before reverse installation and tightening bolts to specified torques.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjjfyjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, fittings, covers and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and further disassemble the travel motor from the final drive.
3) The reverse process to reinstall the components, applying sealant and torquing bolts to specifications.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...jfskemsemm
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are installing the components in reverse order of removal while applying threadlock and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjkkekmdm
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. 13 steps are listed to remove the final drive and travel motor, involving draining oil, removing hoses, bolts, and using lifting devices due to the heavy weight of the components. Proper torque specifications and tools required are also provided.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic lines before removal.
2) Using lifting equipment to remove the final drive and travel motor assembly, travel motor, and coupling.
3) Cleaning and lubricating parts before reverse installation and tightening bolts to specified torques.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjjfyjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, fittings, covers and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and further disassemble the travel motor from the final drive.
3) The reverse process to reinstall the components, applying sealant and torquing bolts to specifications.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...jfskemsemm
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are installing the components in reverse order of removal while applying threadlock and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjkkekmdm
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. 13 steps are listed to remove the final drive and travel motor, involving draining oil, removing hoses, bolts, and using lifting devices due to the heavy weight of the components. Proper torque specifications and tools required are also provided.
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...ze3xiandiao
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. 13 steps are listed to remove the final drive and travel motor, involving draining oil, removing hoses, bolts, and using lifting devices due to the heavy weight of the components. Proper torque specifications and tools required are also provided.
Caterpillar Cat 336E L Excavator (Prefix GTJ) Service Repair Manual (GTJ00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components in the proper order and orientation. It also describes 13 steps to remove the final drive and travel motor as a unit from the excavator as well as 11 steps to install it. Precise torques and angles are specified for bolt tightening.
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are installing the components in reverse order of removal while applying threadlock and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...hfhjskedme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, fittings, covers and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and further disassemble the travel motor from the final drive.
3) The reverse process to reinstall the components, applying sealant and torquing bolts to specifications.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removal.
2) Using lifting equipment to remove the travel motor assembly and separate the final drive and travel motor.
3) Cleaning and lubricating components before reversing the process to install the travel motor.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...zatao0179249295
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, starting with removing the cover and plate using lifting tools. Detailed diagrams accompany each step.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...luanxianshi27
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. It describes removing hoses, fittings, bolts, and lifting the assembly to remove it. The procedure is reversed for installation.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and links using lifting brackets and forcing bolts. Detailed diagrams accompany each step.
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...cnp692569
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly. 10 steps are outlined for removal, including draining oil, removing hoses and fittings, and using lifting tools. 13 steps are given for installation, with torque specifications for the reinstallation bolts.
3. Disassembly instructions for the final drive include removing the cover, plate, and links using lifting brackets and forcing bolts.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and installing lifting brackets to remove internal components. Detailed diagrams accompany each step.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjekkdmmem
The document provides instructions for assembling a travel motor. It describes 27 steps including installing seals, springs, pistons, and other components in the proper order and orientation. Tools required include adapters, nuts, washers, threaded rods, eyebolts, and drivers. The final step is to install the head and bolts, tightening the bolts to a specified torque.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjjskekdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble the internal components of the travel motor in the correct order, which includes installing seals, springs, pistons, bearings, and fasteners. The motor is then installed on the final drive assembly and excavator using lifting equipment due to the heavy weight. Proper torque specifications are listed for all fasteners.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjskekmdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble components like seals, springs, pistons, and plates into the motor housing. Key steps include lubricating mating surfaces, installing retaining rings, and tightening bolts to specified torques. The assembly ends by installing the motor housing cover and bolts, and noting the motor is then ready for installation in the excavator.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjsekqazxkdmmem
This document provides instructions for disassembling and assembling components of an excavator final drive and travel motor. The disassembly process includes removing the cover, plate, sun gear, spacer, planetary gear assembly, retaining ring, washer and planetary gear. The assembly process details installing these components in reverse order and applying the specified torques to the bolts.
Caterpillar Cat 349F L Excavator (Prefix TEW) Service Repair Manual (TEW00001...zatao0179249295
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like part numbers, torque values, and lubrication points to reinstall components in their original positions.
Caterpillar Cat 349F L Excavator (Prefix KEA) Service Repair Manual (KEA00001...zatao0179249295
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It lists 30 steps to disassemble the motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for assembling the motor, such as torque specifications for plugs and bolts, and notes on lubricating sliding surfaces before assembly. The goal is to take the motor apart in a specific sequence and then rebuild it correctly using the provided specifications.
Caterpillar Cat 349F L Excavator (Prefix HPD) Service Repair Manual (HPD00001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations are provided for each step along with safety notices and required tools. The goal is to break down the travel motor into its core components for repair or replacement.
Caterpillar Cat 349F L Excavator (Prefix HLB) Service Repair Manual (HLB00001...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for components like plug torque values and spring dimensions to follow when reassembling the travel motor in reverse order.
More Related Content
Similar to Caterpillar Cat 336E L Excavator (Prefix GTJ) Service Repair Manual (GTJ00001 and up).pdf
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...ze3xiandiao
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor, including installing seals, springs, pistons, and other components in the proper order. 13 steps are listed to remove the final drive and travel motor, involving draining oil, removing hoses, bolts, and using lifting devices due to the heavy weight of the components. Proper torque specifications and tools required are also provided.
Caterpillar Cat 336E L Excavator (Prefix GTJ) Service Repair Manual (GTJ00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components in the proper order and orientation. It also describes 13 steps to remove the final drive and travel motor as a unit from the excavator as well as 11 steps to install it. Precise torques and angles are specified for bolt tightening.
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are installing the components in reverse order of removal while applying threadlock and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...hfhjskedme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, fittings, covers and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and further disassemble the travel motor from the final drive.
3) The reverse process to reinstall the components, applying sealant and torquing bolts to specifications.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removal.
2) Using lifting equipment to remove the travel motor assembly and separate the final drive and travel motor.
3) Cleaning and lubricating components before reversing the process to install the travel motor.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...zatao0179249295
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, starting with removing the cover and plate using lifting tools. Detailed diagrams accompany each step.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...luanxianshi27
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. It describes removing hoses, fittings, bolts, and lifting the assembly to remove it. The procedure is reversed for installation.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and links using lifting brackets and forcing bolts. Detailed diagrams accompany each step.
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...cnp692569
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly. 10 steps are outlined for removal, including draining oil, removing hoses and fittings, and using lifting tools. 13 steps are given for installation, with torque specifications for the reinstallation bolts.
3. Disassembly instructions for the final drive include removing the cover, plate, and links using lifting brackets and forcing bolts.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and installing lifting brackets to remove internal components. Detailed diagrams accompany each step.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjekkdmmem
The document provides instructions for assembling a travel motor. It describes 27 steps including installing seals, springs, pistons, and other components in the proper order and orientation. Tools required include adapters, nuts, washers, threaded rods, eyebolts, and drivers. The final step is to install the head and bolts, tightening the bolts to a specified torque.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjjskekdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble the internal components of the travel motor in the correct order, which includes installing seals, springs, pistons, bearings, and fasteners. The motor is then installed on the final drive assembly and excavator using lifting equipment due to the heavy weight. Proper torque specifications are listed for all fasteners.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjskekmdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble components like seals, springs, pistons, and plates into the motor housing. Key steps include lubricating mating surfaces, installing retaining rings, and tightening bolts to specified torques. The assembly ends by installing the motor housing cover and bolts, and noting the motor is then ready for installation in the excavator.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjsekqazxkdmmem
This document provides instructions for disassembling and assembling components of an excavator final drive and travel motor. The disassembly process includes removing the cover, plate, sun gear, spacer, planetary gear assembly, retaining ring, washer and planetary gear. The assembly process details installing these components in reverse order and applying the specified torques to the bolts.
Similar to Caterpillar Cat 336E L Excavator (Prefix GTJ) Service Repair Manual (GTJ00001 and up).pdf (18)
Caterpillar Cat 349F L Excavator (Prefix TEW) Service Repair Manual (TEW00001...zatao0179249295
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like part numbers, torque values, and lubrication points to reinstall components in their original positions.
Caterpillar Cat 349F L Excavator (Prefix KEA) Service Repair Manual (KEA00001...zatao0179249295
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It lists 30 steps to disassemble the motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for assembling the motor, such as torque specifications for plugs and bolts, and notes on lubricating sliding surfaces before assembly. The goal is to take the motor apart in a specific sequence and then rebuild it correctly using the provided specifications.
Caterpillar Cat 349F L Excavator (Prefix HPD) Service Repair Manual (HPD00001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations are provided for each step along with safety notices and required tools. The goal is to break down the travel motor into its core components for repair or replacement.
Caterpillar Cat 349F L Excavator (Prefix HLB) Service Repair Manual (HLB00001...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for components like plug torque values and spring dimensions to follow when reassembling the travel motor in reverse order.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, seals, bearings, and other internal parts. Various tools are required, and safety precautions are provided to remove parts under spring tension. The goal is to break down the travel motor into its core components to facilitate repair or replacement of parts.
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like torque values and lubrication points for components like plugs, bolts, seals and bearings.
This document provides instructions to disassemble a travel motor on a 349F and 349F L Excavator. It outlines 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, pistons, bearings, seals and other internal parts. Various tools are required, including bolts, nuts, pullers, eyebolts and other lifting devices to safely remove parts. Safety precautions are provided to wear protective equipment when removing parts with spring forces.
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It begins by listing the required tools and safety precautions. The 31 step disassembly process removes components like plugs, springs, pistons, plates and seals. The assembly section lists specifications for components and their installation, such as torque values and lubricants to use.
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, bearings, seals, springs, and pistons. Special care must be taken when removing components under spring pressure. Various tools are required including lifting devices, pullers, bolts and eyebolts to securely support parts being removed.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual (TFG00001...zatao0179249295
1. The document provides step-by-step instructions for disassembling and assembling a hydraulic fan drive for a 349E L excavator.
2. The disassembly process involves removing 22 components and parts from the fan drive assembly including sensors, retainers, seals, plates, discs, and housings.
3. The assembly process lists 8 steps including pressing components back together and installing new seals, sleeves and retaining rings. Precise instructions are provided along with required tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. The disassembly process involves removing 22 components from the fan drive including bolts, retainers, seals, discs, plates, and bearings. The assembly process is the reverse and includes applying sealant and installing the components in the proper order and orientation using various tools. Special care must be taken when handling springs and seals. Cleanliness is important to prevent contamination.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...zatao0179249295
This document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper tooling is required and parts must be cleaned, marked and replaced in their original locations and orientations. Safety notices warn of spring forces, contained fluids, and preventing contamination.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...zatao0179249295
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening to specified torques. Tools required are listed for each procedure.
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing and installing the rear gear group components like gears, covers, seals, and bearings. Precise measurements and tooling are required for proper installation.
- Procedures for removing and installing the flywheel, which requires lifting equipment due to its weight. The ring gear must be heated for removal and cooled for installation.
- Removing and installing the crankshaft rear seal using specific bolts and torque specifications. Inspection of the crankshaft surface is also noted.
Precise measurements and use of the correct tools are emphasized for correct re
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...zatao0179249295
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
1. The rear gear group is removed by taking off bolts, seals, gears, and covers. Proper bearing installation is emphasized.
2. Flywheel removal requires lifting equipment due to its weight. Installation involves heating the ring gear, applying loctite, and torqueing bolts.
3. Removing the crankshaft rear seal involves taking off bolts. Inspection of the seal surface and crankshaft specifications is noted.
4. Installing the rear seal requires cleaning, applying primer and retaining compound, and following a tightening sequence.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...zatao0179249295
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, sun gear and planetary gears. The assembly process instructs to clean parts and apply lubricants before reinstalling components like bearings, seals and gears in the reverse order of disassembly. Proper alignment and pressing of components into place is emphasized.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure describes installing these components in reverse order and provides details on properly positioning bearings and applying threadlocker to bolts. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...zatao0179249295
This document provides instructions for removing and installing the rear gear group on a 345D L excavator with a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 11 steps in the reverse order and provides notes on properly installing bearings, seals, and gears. Tools required are also listed.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR GTJ
Configuration: 336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 17 23:39:27 UTC+0800 2020
10/10
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR GTJ
Configuration: 336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 17 23:40:22 UTC+0800 2020
5/5
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR GTJ
Configuration: 336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g02131875
4. Remove retaining ring (7), washer (8), planetary gear (9), roller bearing (11), and washer
(12) from carrier assembly (13).
5. Remove retaining ring (10) and sun gear (14) from carrier assembly (13).
Illustration 5 g02131876
6. Remove spacer (16).
7. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (15). The weight
of planetary gear assembly (15) is approximately 32 kg (70 lb). Remove planetary gear
assembly (15).
3/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 6 g02131877
8. Drive spring pin (17) into planetary shaft (18) with a suitable hammer and a suitable punch.
9. Remove planetary shaft (18), washer (20), roller bearing (20), planetary gear (23), and
washer (24) from the carrier assembly (21).
10. Remove spring pin (17) from planetary shaft (18) with a suitable hammer and a suitable
punch.
11. Remove retaining ring (19) and sun gear (25) from carrier assembly (21).
Illustration 7 g02131878
12. Remove spacer (26).
13. Attach Tooling (A) and a suitable lifting device to ring gear (27). The weight of ring gear
(27) is approximately 70 kg (155 lb). Remove bolts (28) and ring gear (27).
4/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 8 g02131879
14. Remove O-ring seal (29).
15. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (30). The weight
of planetary gear assembly (30) is approximately 57 kg (125 lb). Remove planetary gear
assembly (30).
Illustration 9 g02131881
16. Drive spring pin (31) into planetary shaft (32) with a suitable hammer and a suitable punch.
17. Remove planetary shaft (32), washer (33), roller bearings (35), planetary gear (36), and
washer (36) from the carrier assembly (34).
18. Remove spring pin (31) from planetary shaft (32) with a suitable hammer and a suitable
punch.
5/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 10 g02131882
Illustration 11 g02131885
19. Remove bolts (38). Use Tooling (B) in order to remove gear (39).
Illustration 12 g02131886
20. Remove shims (40).
6/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 13 g02131887
21. Attach Tooling (C) and a suitable lifting device to sprocket housing (41). The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Remove sprocket housing (41) and
roller bearing (42).
Illustration 14 g02131888
22. Remove bearing races (43) and Duo-Cone seal (44) from sprocket housing (41).
7/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 15 g02132155
23. Remove Duo-Cone seal (45) and roller bearing (47) from motor housing (48). The weight of
motor housing (48) is approximately 91 kg (200 lb).
24. If necessary, remove dowels (46) from motor housing (48).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 17 23:41:18 UTC+0800 2020
8/8
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR GTJ
Configuration: 336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i05103849
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
D 5P-3931 Anti-Seize Compound -
E 1U-9895 Crossblock 1
F 6V-2012 Depth Micrometer 1
G 6V-7059 Micrometer () 1
H - Loctite 242 -
J 6V-2055 Grease -
K - Loctite 17430 -
L 8T-9206 Seal Installer 1
1/12
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g02132155
1. Apply Tooling (D) to the surface of dowels (46) . Install dowels (46) .
2. Raise the temperature of roller bearing (47) . Install the roller bearing (47) on motor housing
(48) .
3. Install Duo-Cone seal (45) .
Illustration 2 g02131888
4. Lower the temperature of bearing races (43) . Install bearing races (43) in sprocket housing
(41) .
5. Install Duo-Cone seal (44) .
2/12
336E & 336E L Excavators GTJ00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...