1. The document provides instructions for installing and disassembling the piston pump on a 336D2 excavator.
2. It describes 30 steps for assembling the piston pump, including installing bearings, seals, springs, and housing components in the proper order.
3. The disassembly instructions list 8 steps for removing the piston motor, such as removing bolts, seals, springs, and bearings. Tools and safety precautions are also provided.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing bearings, seals, pistons, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts to access the motor. Safety precautions are provided throughout regarding spring-loaded parts that could cause injury.
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing various bearings, seals, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts. Cleanliness is emphasized throughout assembly and disassembly. Required tools are listed.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...fjjskekdmmem
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 29 steps to disassemble the pump, including removing bolts, seals, bearings, pistons, springs and other components. The assembly procedure is described as installing these components in reverse order while taking precautions for spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskmdmem
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the pump with 30 parts in 29 steps, requiring cleaning of parts, application of specific temperatures, and use of tools including retaining ring pliers and a dial indicator. Safety precautions are provided throughout regarding spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing bearings, seals, pistons, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts to access the motor. Safety precautions are provided throughout regarding spring-loaded parts that could cause injury.
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing various bearings, seals, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts. Cleanliness is emphasized throughout assembly and disassembly. Required tools are listed.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...fjjskekdmmem
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 29 steps to disassemble the pump, including removing bolts, seals, bearings, pistons, springs and other components. The assembly procedure is described as installing these components in reverse order while taking precautions for spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskmdmem
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the pump with 30 parts in 29 steps, requiring cleaning of parts, application of specific temperatures, and use of tools including retaining ring pliers and a dial indicator. Safety precautions are provided throughout regarding spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...ufjksemd8ujd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires draining fluids, removing mounting bolts and seals, and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and sockets, which may require removing a wear sleeve.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes in the seal.
- Installing a new crankshaft front seal using a installer tool and applying oil to the seal and crankshaft pulley.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...ufjksemd8ujd
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The removal procedure involves locking the crankshaft, camshaft, and fuel injection pump in position using timing pins. Components like the idler gears, camshaft gear, and housing bearing are then removed. Installation follows the reverse order, with lubrication of gears and checking of timing, backlash, and end play measurements upon completion. Tools and torque specifications are provided.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...ufjksemd8ujd
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to clearly show how to disassemble the various systems.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...ufjksemd8ujd
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening bolts to specification.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing a crankshaft rear seal housing assembly using alignment tools and tightening setscrews in a specific order.
- Removing and installing a crankshaft wear sleeve using pullers and installation sleeves to reclaim worn seal surfaces.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...ufjksemd8ujd
The document provides instructions for installing a flywheel and crankshaft rear seal on a 3054C engine. It includes:
1) Heating the ring gear to install it on the flywheel, then installing the flywheel using guide bolts and tightening bolts to the specified torque.
2) Removing the crankshaft rear seal housing assembly by removing setscrews, as the seal is non-serviceable and the housing must be replaced.
3) Installing the new crankshaft rear seal housing assembly by positioning it over the crankshaft, aligning it, and tightening setscrews to the specified torque using an alignment tool.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...ufjksemd8ujd
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in a specific sequence, and refilling fluids before installing removed components.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...ufjksemd8ujd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling the components. Safety notices are included to warn of potential injuries from parts under spring pressure, hydraulic oil pressure, and hot oil. The components are to be marked for proper reassembly.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054C engine. The removal procedure involves taking out setscrews and the housing assembly. For installation, the new seal assembly is pushed onto the crankshaft flange with a plastic sleeve for protection. Setscrews are then tightened to secure the housing assembly to the cylinder block. Proper cleaning, alignment with tools, and torque specifications are emphasized to complete the process.
This document provides instructions for removing and installing various components of a Caterpillar 312D excavator engine, including:
- Removing and installing the flywheel housing, which requires lifting devices and bolts.
- Removing and installing the crankshaft rear seal, using a slide hammer, distorter, and installer tool.
- Removing and installing the crankshaft pulley, using a combination puller and socket tools. Heating may be required to install wear sleeves.
- Guidelines are provided for cleaning parts and applying retaining compounds during installation. Torque specifications and required tools are listed for each procedure.
The document provides instructions for installing a flywheel on a 3054C engine. It includes the following steps:
1. Clean the flywheel housing and inspect the crankshaft rear seal for leaks.
2. Heat the ring gear to 250°C and quickly install it on the flywheel, ensuring correct orientation.
3. Install guide bolts and lifting brackets to position the flywheel, then install and tighten the bolts to the specified torque.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...ufjksemd8ujd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires draining fluids, removing mounting bolts and seals, and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and sockets, which may require removing a wear sleeve.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes in the seal.
- Installing a new crankshaft front seal using a installer tool and applying oil to the seal and crankshaft pulley.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...ufjksemd8ujd
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The removal procedure involves locking the crankshaft, camshaft, and fuel injection pump in position using timing pins. Components like the idler gears, camshaft gear, and housing bearing are then removed. Installation follows the reverse order, with lubrication of gears and checking of timing, backlash, and end play measurements upon completion. Tools and torque specifications are provided.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...ufjksemd8ujd
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to clearly show how to disassemble the various systems.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...ufjksemd8ujd
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening bolts to specification.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing a crankshaft rear seal housing assembly using alignment tools and tightening setscrews in a specific order.
- Removing and installing a crankshaft wear sleeve using pullers and installation sleeves to reclaim worn seal surfaces.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...ufjksemd8ujd
The document provides instructions for installing a flywheel and crankshaft rear seal on a 3054C engine. It includes:
1) Heating the ring gear to install it on the flywheel, then installing the flywheel using guide bolts and tightening bolts to the specified torque.
2) Removing the crankshaft rear seal housing assembly by removing setscrews, as the seal is non-serviceable and the housing must be replaced.
3) Installing the new crankshaft rear seal housing assembly by positioning it over the crankshaft, aligning it, and tightening setscrews to the specified torque using an alignment tool.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...ufjksemd8ujd
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in a specific sequence, and refilling fluids before installing removed components.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...ufjksemd8ujd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling the components. Safety notices are included to warn of potential injuries from parts under spring pressure, hydraulic oil pressure, and hot oil. The components are to be marked for proper reassembly.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054C engine. The removal procedure involves taking out setscrews and the housing assembly. For installation, the new seal assembly is pushed onto the crankshaft flange with a plastic sleeve for protection. Setscrews are then tightened to secure the housing assembly to the cylinder block. Proper cleaning, alignment with tools, and torque specifications are emphasized to complete the process.
This document provides instructions for removing and installing various components of a Caterpillar 312D excavator engine, including:
- Removing and installing the flywheel housing, which requires lifting devices and bolts.
- Removing and installing the crankshaft rear seal, using a slide hammer, distorter, and installer tool.
- Removing and installing the crankshaft pulley, using a combination puller and socket tools. Heating may be required to install wear sleeves.
- Guidelines are provided for cleaning parts and applying retaining compounds during installation. Torque specifications and required tools are listed for each procedure.
The document provides instructions for installing a flywheel on a 3054C engine. It includes the following steps:
1. Clean the flywheel housing and inspect the crankshaft rear seal for leaks.
2. Heat the ring gear to 250°C and quickly install it on the flywheel, ensuring correct orientation.
3. Install guide bolts and lifting brackets to position the flywheel, then install and tighten the bolts to the specified torque.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02732015
Piston Pump (Hydraulic Fan) - Assemble
SMCS - 1387-016-QP; 5070-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
D 8T-5096 Dial Indicator Gp 1
Illustration 1 g01212915
1. Lower the temperature of bearing cup (49). Install bearing cup (49).
1/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01212913
2. Install lip seal (48).
3. Use Tooling (B) in order to install retaining ring (47).
Illustration 3 g01213404
4. Raise the temperature of bearing cone (46).
5. Install bearing cone (46) onto shaft (45).
Illustration 4 g01213405
6. Install bearing cone (46), shaft (45), and bearing cone (31).
2/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01213407
7. Lower the temperature of bearing cone (26). Install bearing cone (26).
Illustration 6 g01212900
8. Position head (23) onto the housing.
9. Install bolts (22).
Illustration 7 g01213409
10. Use Tooling (D) in order to determine the end play of shaft (45).
3/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g01212900
11. Remove bolts (22) and head (23).
Illustration 9 g01213405
12. Remove bearing cone (31).
Illustration 10 g01213433
13. Install bearings (44).
4/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g01212910
14. Install swashplate (43).
Illustration 12 g01373818
15. Install shim (40), spring (41), and shim (42) to barrel (38).
Illustration 13 g01212908
5/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
16. Use Tooling (A), Tooling (B), and a suitable press in order to install retaining ring (39) into
barrel (38).
Illustration 14 g01212907
17. Install pins (37) into barrel (38).
Illustration 15 g01212906
18. Install bearing (36), retainer (35), and pistons (34).
6/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 16 g01212905
19. Install rotating group (32) and shim (33).
Note: Shim thickness was determined on Step 9.
Illustration 17 g01212904
20. Install bearing cone (31).
Illustration 18 g01212903
21. Install piston (30).
7/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 19 g01212902
22. Install spring (27), piston (29), and O-ring seal (28).
Illustration 20 g01213436
23. Install O-ring seals (24) and port plate (25).
Illustration 21 g01212900
8/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install head (23) and bolts (22).
Illustration 22 g01212898
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
25. Install spool (15), poppet (16), spring (17), spring (18), shim (19), O-ring seal (20), and
housing (21) into housing (2).
26. Install retainer (7), spring (8), retainer (9), spool (10), O-ring seal (12), backup ring (11), O-
ring seal (13), and cartridge (14).
27. Install screw (6) into housing (2).
9/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g01212897
28. Install coil (4) and nut (5).
Illustration 24 g01212896
29. Install O-ring seals (3).
Illustration 25 g01212895
30. Install controller (2) and bolts (1).
End By:
10/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 En...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Fan)
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 19:55:55 UTC+0800 2020
11/11
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 En...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02424411
Piston Pump (Hydraulic Fan) - Install
SMCS - 1387-012-QP; 5070-012-HFN
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01211400
1. Position piston pump (7) and install bolts (6).
2. Connect harness assembly (5).
3. Connect hose assemblies (3) and (4).
1/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01211399
4. Connect hose assembly (2).
Illustration 3 g01206719
5. Close door (1).
6. Fill the hydraulic system with oil. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 19:56:51 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415451
Piston Motor (Hydraulic Fan) - Remove
SMCS - 1386-011-QP; 5058-011-FM
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01207415
1. Bend locking tabs (1) backward.
2. Remove bolts (2) and hub (3).
1/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01207416
3. Use a suitable lifting device to position fan motor assembly (4) onto suitable cribbing. The
weight of fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207418
4. Attach a suitable lifting device to piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
5. Remove bolts (6) and fan motor (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 19:57:47 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415272
Piston Motor (Hydraulic Fan) - Disassemble
SMCS - 1386-015-QP; 5058-015-FM; 5058-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Start By:
a. Remove the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Remove".
1/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g01207275
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (1) and head (2).
Illustration 2 g01207276
2. Remove O-ring seal (3), port plate (4), and bearing cup (5).
Illustration 3 g01207278
2/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (6), sleeve (7), poppet (8), spring (9), poppet (10), and O-ring seal (11).
Illustration 4 g01207279
4. Remove bearing cone (12).
Illustration 5 g01207280
5. Remove shim (13) and rotating group (14).
3/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 9 g01207284
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Use Tooling (C) and Tooling (B) in order to remove retaining ring (19).
10. Remove shim (23), spring (22), and shim (21).
Illustration 10 g01207285
11. Remove swashplate (24) and shaft (25).
5/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 11 g01207287
12. Use Tooling (A) in order to remove bearing cone (26) from shaft (25).
Illustration 12 g01207286
13. Use Tooling (C) in order to remove retaining ring (27).
14. Remove lip seal (28).
Illustration 13 g01207288
15. Remove bearing cup (29).
6/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR TLY
Configuration: 336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 12 g01207276
15. Lower the temperature of bearing cup (5).
16. Install bearing cup (5), port plate (4), and O-ring seal (3).
Illustration 13 g01207275
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install head (2) and bolts (1).
End By:
a. Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install".
6/7
336D2 & 336D2 L Excavators TLY00001-UP (MACHINE) POWERED BY C9 Engin...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...