This document provides instructions for installing and removing the final drive and travel motor, and disassembling and assembling the swivel, on Caterpillar 336D2 and 336D2 L excavators. The procedures include using lifting devices and tools to position, connect, and secure components. Cleanliness is emphasized to prevent contamination. O-rings, seals, and gaskets should be checked and replaced if needed before assembly.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The documents provide instructions for assembling and disassembling a swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position housing and rotor components of the swivel for disassembly and assembly. The housings weigh approximately 20-43 kg.
3. Removing and installing seals, plugs, retainers, covers, and bolts in the described order and using the specified tools to fully disassemble and reassemble the swivel.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...ikdkdmddm
The documents provide instructions for assembling and disassembling a swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position housing and rotor components of the swivel for disassembly and assembly. The housings weigh approximately 20-43 kg.
3. Removing and installing seals, plugs, retainers, covers, and bolts in the described order and using the specified tools to fully disassemble and reassemble the swivel.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...ze3xiandiao
The documents provide instructions for assembling and disassembling the swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position parts like the swivel joint, outside housing, and rotor during disassembly and assembly due to the parts weighing 20-45 kg.
3. Removing components like bolts, washers, covers, seals and O-rings from the outside housing and rotor using the specified tools to fully disassemble the swivel.
4. Ensuring cleanliness is critical during assembly and not using rags which could leave lint and cause issues.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The documents provide instructions for assembling and disassembling a swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position housing and rotor components of the swivel for disassembly and assembly. The housings weigh approximately 20-43 kg.
3. Removing and installing seals, plugs, retainers, covers, and bolts in the described order and using the specified tools to fully disassemble and reassemble the swivel.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...ikdkdmddm
The documents provide instructions for assembling and disassembling a swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position housing and rotor components of the swivel for disassembly and assembly. The housings weigh approximately 20-43 kg.
3. Removing and installing seals, plugs, retainers, covers, and bolts in the described order and using the specified tools to fully disassemble and reassemble the swivel.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...ze3xiandiao
The documents provide instructions for assembling and disassembling the swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position parts like the swivel joint, outside housing, and rotor during disassembly and assembly due to the parts weighing 20-45 kg.
3. Removing components like bolts, washers, covers, seals and O-rings from the outside housing and rotor using the specified tools to fully disassemble the swivel.
4. Ensuring cleanliness is critical during assembly and not using rags which could leave lint and cause issues.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The documents provide instructions for assembling and disassembling a swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position housing and rotor components of the swivel for disassembly and assembly. The housings weigh approximately 20-43 kg.
3. Removing and installing seals, plugs, retainers, covers, and bolts in the described order and using the specified tools to fully disassemble and reassemble the swivel.
Caterpillar Cat 336D2 L Excavator (Prefix XBH) Service Repair Manual (XBH0000...km7seydwuhdw
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fhjsjkdmemm
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fjjskmdmem
The document provides instructions for assembling and disassembling a swivel component for an excavator. It describes:
1) How to disassemble the swivel by removing bolts, washers, covers and seals from the outside housing and rotor using specialized tools.
2) How to assemble the swivel by cleaning all parts, placing seals on the outside housing and rotor, and installing the outside housing and rotor together using bolts, washers and a retainer.
3) The importance of cleanliness during assembly to prevent contaminants from causing wear and failure of components.
Caterpillar Cat 349F L Excavator (Prefix TEW) Service Repair Manual (TEW00001...zatao0179249295
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like part numbers, torque values, and lubrication points to reinstall components in their original positions.
Caterpillar Cat 349F L Excavator (Prefix KEA) Service Repair Manual (KEA00001...zatao0179249295
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It lists 30 steps to disassemble the motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for assembling the motor, such as torque specifications for plugs and bolts, and notes on lubricating sliding surfaces before assembly. The goal is to take the motor apart in a specific sequence and then rebuild it correctly using the provided specifications.
Caterpillar Cat 349F L Excavator (Prefix HPD) Service Repair Manual (HPD00001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations are provided for each step along with safety notices and required tools. The goal is to break down the travel motor into its core components for repair or replacement.
Caterpillar Cat 349F L Excavator (Prefix HLB) Service Repair Manual (HLB00001...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for components like plug torque values and spring dimensions to follow when reassembling the travel motor in reverse order.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, seals, bearings, and other internal parts. Various tools are required, and safety precautions are provided to remove parts under spring tension. The goal is to break down the travel motor into its core components to facilitate repair or replacement of parts.
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like torque values and lubrication points for components like plugs, bolts, seals and bearings.
This document provides instructions to disassemble a travel motor on a 349F and 349F L Excavator. It outlines 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, pistons, bearings, seals and other internal parts. Various tools are required, including bolts, nuts, pullers, eyebolts and other lifting devices to safely remove parts. Safety precautions are provided to wear protective equipment when removing parts with spring forces.
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It begins by listing the required tools and safety precautions. The 31 step disassembly process removes components like plugs, springs, pistons, plates and seals. The assembly section lists specifications for components and their installation, such as torque values and lubricants to use.
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, bearings, seals, springs, and pistons. Special care must be taken when removing components under spring pressure. Various tools are required including lifting devices, pullers, bolts and eyebolts to securely support parts being removed.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual (TFG00001...zatao0179249295
1. The document provides step-by-step instructions for disassembling and assembling a hydraulic fan drive for a 349E L excavator.
2. The disassembly process involves removing 22 components and parts from the fan drive assembly including sensors, retainers, seals, plates, discs, and housings.
3. The assembly process lists 8 steps including pressing components back together and installing new seals, sleeves and retaining rings. Precise instructions are provided along with required tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
More Related Content
Similar to Caterpillar Cat 336D2 Excavator (Prefix XBH) Service Repair Manual (XBH00001 and up).pdf
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are then used to secure the housing and rotor. Finally, the swivel is tested for leaks by applying air pressure before being fully installed on the excavator.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The documents provide instructions for assembling and disassembling a swivel component of an excavator. Key steps include:
1. Cleaning all parts thoroughly before assembly to prevent contamination.
2. Using lifting devices and tools to position housing and rotor components of the swivel for disassembly and assembly. The housings weigh approximately 20-43 kg.
3. Removing and installing seals, plugs, retainers, covers, and bolts in the described order and using the specified tools to fully disassemble and reassemble the swivel.
Caterpillar Cat 336D2 L Excavator (Prefix XBH) Service Repair Manual (XBH0000...km7seydwuhdw
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fhjsjkdmemm
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fjjskmdmem
The document provides instructions for assembling and disassembling a swivel component for an excavator. It describes:
1) How to disassemble the swivel by removing bolts, washers, covers and seals from the outside housing and rotor using specialized tools.
2) How to assemble the swivel by cleaning all parts, placing seals on the outside housing and rotor, and installing the outside housing and rotor together using bolts, washers and a retainer.
3) The importance of cleanliness during assembly to prevent contaminants from causing wear and failure of components.
Similar to Caterpillar Cat 336D2 Excavator (Prefix XBH) Service Repair Manual (XBH00001 and up).pdf (11)
Caterpillar Cat 349F L Excavator (Prefix TEW) Service Repair Manual (TEW00001...zatao0179249295
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like part numbers, torque values, and lubrication points to reinstall components in their original positions.
Caterpillar Cat 349F L Excavator (Prefix KEA) Service Repair Manual (KEA00001...zatao0179249295
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It lists 30 steps to disassemble the motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for assembling the motor, such as torque specifications for plugs and bolts, and notes on lubricating sliding surfaces before assembly. The goal is to take the motor apart in a specific sequence and then rebuild it correctly using the provided specifications.
Caterpillar Cat 349F L Excavator (Prefix HPD) Service Repair Manual (HPD00001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations are provided for each step along with safety notices and required tools. The goal is to break down the travel motor into its core components for repair or replacement.
Caterpillar Cat 349F L Excavator (Prefix HLB) Service Repair Manual (HLB00001...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for components like plug torque values and spring dimensions to follow when reassembling the travel motor in reverse order.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, seals, bearings, and other internal parts. Various tools are required, and safety precautions are provided to remove parts under spring tension. The goal is to break down the travel motor into its core components to facilitate repair or replacement of parts.
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like torque values and lubrication points for components like plugs, bolts, seals and bearings.
This document provides instructions to disassemble a travel motor on a 349F and 349F L Excavator. It outlines 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, pistons, bearings, seals and other internal parts. Various tools are required, including bolts, nuts, pullers, eyebolts and other lifting devices to safely remove parts. Safety precautions are provided to wear protective equipment when removing parts with spring forces.
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It begins by listing the required tools and safety precautions. The 31 step disassembly process removes components like plugs, springs, pistons, plates and seals. The assembly section lists specifications for components and their installation, such as torque values and lubricants to use.
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, bearings, seals, springs, and pistons. Special care must be taken when removing components under spring pressure. Various tools are required including lifting devices, pullers, bolts and eyebolts to securely support parts being removed.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual (TFG00001...zatao0179249295
1. The document provides step-by-step instructions for disassembling and assembling a hydraulic fan drive for a 349E L excavator.
2. The disassembly process involves removing 22 components and parts from the fan drive assembly including sensors, retainers, seals, plates, discs, and housings.
3. The assembly process lists 8 steps including pressing components back together and installing new seals, sleeves and retaining rings. Precise instructions are provided along with required tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. The disassembly process involves removing 22 components from the fan drive including bolts, retainers, seals, discs, plates, and bearings. The assembly process is the reverse and includes applying sealant and installing the components in the proper order and orientation using various tools. Special care must be taken when handling springs and seals. Cleanliness is important to prevent contamination.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...zatao0179249295
This document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper tooling is required and parts must be cleaned, marked and replaced in their original locations and orientations. Safety notices warn of spring forces, contained fluids, and preventing contamination.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...zatao0179249295
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening to specified torques. Tools required are listed for each procedure.
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing and installing the rear gear group components like gears, covers, seals, and bearings. Precise measurements and tooling are required for proper installation.
- Procedures for removing and installing the flywheel, which requires lifting equipment due to its weight. The ring gear must be heated for removal and cooled for installation.
- Removing and installing the crankshaft rear seal using specific bolts and torque specifications. Inspection of the crankshaft surface is also noted.
Precise measurements and use of the correct tools are emphasized for correct re
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...zatao0179249295
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
1. The rear gear group is removed by taking off bolts, seals, gears, and covers. Proper bearing installation is emphasized.
2. Flywheel removal requires lifting equipment due to its weight. Installation involves heating the ring gear, applying loctite, and torqueing bolts.
3. Removing the crankshaft rear seal involves taking off bolts. Inspection of the seal surface and crankshaft specifications is noted.
4. Installing the rear seal requires cleaning, applying primer and retaining compound, and following a tightening sequence.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...zatao0179249295
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, sun gear and planetary gears. The assembly process instructs to clean parts and apply lubricants before reinstalling components like bearings, seals and gears in the reverse order of disassembly. Proper alignment and pressing of components into place is emphasized.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure describes installing these components in reverse order and provides details on properly positioning bearings and applying threadlocker to bolts. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...zatao0179249295
This document provides instructions for removing and installing the rear gear group on a 345D L excavator with a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 11 steps in the reverse order and provides notes on properly installing bearings, seals, and gears. Tools required are also listed.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07188136
Final Drive and Travel Motor - Install
SMCS - 4050-012; 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 439-3938 Link Bracket 1
D - Loctite C5A Copper Anti-Seize -
Note: Check the O-ring seals for wear or for damage. Replace the O-ring seals, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01181921
1. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
2. Position travel motor (11). Install bolts (12) that mount travel motor (11) to final drive (13).
2/5
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 2 g01181917
3. Install O-ring seals (10) and (9).
Illustration 3 g01181914
4. Install counterbalance valve (8) and bolts (7).
Illustration 4 g01181911
3/5
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 5 g01182266
5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb).
6. Carefully position final drive and travel motor (5). Apply Tooling (D) to the threads of bolts
(6).
7. Tighten bolts (6) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
Illustration 6 g01223711
8. Install fitting (4). Connect hose assemblies (3).
4/5
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 7 g00944947
9. Remove Tooling (A). Install the cap onto the hydraulic tank.
10. Fill the hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System
Oil Level - Check". Refer to Operation and Maintenance Manual, "Lubricant Viscosities
and Refill Capacities".
Illustration 8 g01223707
11. Install cover (2) and bolts (1). Tighten bolts (1) to a torque of 130 ± 10 N·m (96 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:26:54 UTC+0800 2020
5/5
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434256
Swivel - Remove
SMCS - 5060-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 1 g01209599
1. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 2 g01216069
2. Disconnect hose assemblies (1), (2), and (3). Remove support (4).
Illustration 3 g01216082
2/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 3. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Remove bolts (6) and retainer (8). Remove clamp (7) and boot
(5).
Illustration 4 g01216099
4. Remove bolts (10) and covers (11).
Illustration 5 g01216098
5. Disconnect hose assemblies (15). Disconnect fitting (16). Disconnect hose assemblies (12).
Remove fittings (14). Remove bolts (13). Remove swivel (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:27:50 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02568407
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
6V-3822 Bolt 2
6V-5839 Washer 2
1P-5546 Crossblock 1
5P-4168 Step Plate 1
5F-7366 Screw 1
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the swivel joint. Refer to Disassembly and Assembly, "Swivel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 1. Thoroughly clean the outside of the swivel joint prior to disassembly.
Illustration 1 g00633843
Illustration 2 g00633841
2. Use a suitable lifting device to position the swivel joint onto Tooling (B). Fasten the swivel joint to
Tooling (B), as shown. The weight of the swivel joint is approximately 43 kg (95 lb).
3. Remove bolts (1), washers (2), and cover (3) from outside housing (8).
4. Remove O-ring seal (7) from outside housing (8).
5. Remove bolts (4), washers (5), and retainer (6) from rotor (11).
2/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 6. Use Tooling (A) in order to separate the outside housing (8) from rotor (11). The weight of outside
housing (8) is approximately 20 kg (45 lb). The weight of rotor (11) is approximately 21 kg (46 lb).
7. Remove seals (9) from outside housing (8).
8. Remove O-ring seals (10) from the outside housing (8).
9. Remove plug (13). Remove O-ring seal (12) from plug (13).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:28:46 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02426337
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components,
if necessary.
1/2
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g00633843
1. Install O-ring seal (12) on plug (13). Apply clean hydraulic oil on the seal. Install plug (13).
2. Install seals (9) and O-ring seals (10) into outside housing (8).
3. Carefully install outside housing (8) over rotor (11).
4. Install retainer (6), washers (5), and bolts (4). This holds the rotor (11) and the outside housing (8)
together.
5. Apply clean hydraulic oil on O-ring seal (7). Install the O-ring seal in the outside housing.
6. Install cover (3), washers (2), and bolts (1) that secure the cover.
7. Check the swivel joint for leaks. Plug the drain ports of the inside body. Apply shop air pressure in
the top of the swivel joint and check the swivel joint for leaks. The shop air pressure should be
between 0.2758 MPa (40 psi) and 0.4137 MPa (60 psi).
End By:
a. Install the swivel joint. Refer to Disassembly and Assembly, "Swivel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:29:43 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434356
Swivel - Install
SMCS - 5060-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Illustration 1 g01216082
1. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Position swivel (9). Install boot (5) and clamp (7). Install
retainer (8) and bolts (6).
1/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 2 g01216069
2. Connect hose assemblies (1), (2), and (3). Install support (4).
Illustration 3 g01216098
3. Install bolts (13). Install fittings (14). Install fitting (16). Connect hose assemblies (15).
Connect hose assemblies (14) and (12) to swivel (9).
Illustration 4 g01216099
4. Install covers (11) and bolts (10).
2/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 5 g01209599
5. Remove Tooling (A).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:30:39 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434311
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Remove
SMCS - 5479-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes
for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Illustration 1 g00690963
1. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A).
Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the
hydraulic system.
2/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 2 g01206719
2. Open door (1).
Illustration 3 g01216136
3. Disconnect harness assemblies (4).
4. Disconnect hose assemblies (2) and (3).
5. Remove bolts (5) and solenoid valve (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:31:36 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02434312
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Install
SMCS - 5479-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01216136
1/2
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. 1. Install solenoid valve (6) and bolts (5).
2. Connect hose assemblies (2) and (3).
3. Connect harness assemblies (4).
Illustration 2 g01206719
4. Close door (1).
Illustration 3 g00690963
5. Remove Tooling (A) from the hydraulic tank.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:32:32 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02413351
Swing Cushion Valve - Remove
SMCS - 5454-015
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
Illustration 1 g01206252
1. Disconnect hose assemblies (1) and (2). Disconnect harness assembly (4). Remove bolts (3)
and remove swing cushion valve (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 4 10:33:29 UTC+0800 2020
1/1
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02096925
Swing Cushion Valve - Disassemble - Fine Swing Solenoid
SMCS - 5454-015
Disassembly Procedure
Start By:
a. Remove the swing cushion valve. Refer to Disassembly and Assembly, "Swing Cushion
Valve - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
Illustration 1 g00702083
1. Remove O-ring seals (1) and (2) from the valve body.
2. Remove the fine swing solenoid, as follows.
1/4
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 2 g00702084
a. Remove bolts (3).
b. Remove fine swing solenoid (4).
Illustration 3 g00702085
c. Remove O-ring seal (8), (6), (7), and (5).
3. Remove the relief valves, as follows.
Illustration 4 g00702097
2/4
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 5 g00702102
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
a. Remove relief valve (9) from the valve body.
b. Remove spring (12), plunger (11), and ball valve (10) from relief valve (9).
Illustration 6 g00702106
c. Remove backup ring (13) and O-ring seal (14) from the relief valve.
4. Repeat Steps 3.a through 3.c for the remaining relief valve.
Thu Jun 4 10:34:25 UTC+0800 2020
3/4
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
4/4
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR XBH
Configuration: 336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02096926
Swing Cushion Valve - Assemble - Fine Swing Solenoid
SMCS - 5454-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6396 O-Ring Assembly Compound
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use Tooling (A) during the assembly procedure.
1. Install the relief valves, as follows.
1/4
336D2 & 336D2 L Excavators XBH00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...